Go to page of
Similar user manuals
-
Network Card
Transition Networks SSDTF1029-106
9 pages 0.7 mb -
Network Card
Transition Networks E-100BTX-FX-05
7 pages 0.27 mb -
Network Card
Transition Networks SSDTF1018-105
9 pages 0.7 mb -
Network Card
Transition Networks CSRFB10XX-100
9 pages 0.67 mb -
Network Card
Transition Networks E-TX-MC01
2 pages 0.09 mb -
Network Card
Transition Networks N-FX-SC-01
16 pages 0.08 mb -
Network Card
Transition Networks SSDTF1022-105
9 pages 0.7 mb -
Network Card
Transition Networks SSDTF1025-105
9 pages 0.7 mb
A good user manual
The rules should oblige the seller to give the purchaser an operating instrucion of Transition Networks SSDTF1013-105, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.
What is an instruction?
The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Transition Networks SSDTF1013-105 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.
Unfortunately, only a few customers devote their time to read an instruction of Transition Networks SSDTF1013-105. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.
What should a perfect user manual contain?
First and foremost, an user manual of Transition Networks SSDTF1013-105 should contain:
- informations concerning technical data of Transition Networks SSDTF1013-105
- name of the manufacturer and a year of construction of the Transition Networks SSDTF1013-105 item
- rules of operation, control and maintenance of the Transition Networks SSDTF1013-105 item
- safety signs and mark certificates which confirm compatibility with appropriate standards
Why don't we read the manuals?
Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Transition Networks SSDTF1013-105 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Transition Networks SSDTF1013-105, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Transition Networks service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Transition Networks SSDTF1013-105.
Why one should read the manuals?
It is mostly in the manuals where we will find the details concerning construction and possibility of the Transition Networks SSDTF1013-105 item, and its use of respective accessory, as well as information concerning all the functions and facilities.
After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.
Table of contents for the manual
-
Page 1
Installation . . . . . . . . . . . . . . . . . . . . .3 Operation . . . . . . . . . . . . . . . . . . . . . .9 Cable Specifications . . . . . . . . . . . . .10 Technical Specifications . . . . . . . . . .12 Troubleshooting . . . . . . . . . . . . . . . .13 Compliance Information . . . . . . . . .16 * Typical maximum cable distance. (Actual distance[...]
-
Page 2
2 SSDTF10xx-10x (TX) = transmit (RX) = receive * Typical maximum cable distance. Actual distance is dependent upon the physical characteristics of the network. ** SSDTF1029-105 and -106 are intended to be installed in the same network where one is the local device and the other is the remote device. *** SSDTF1029-107 and -108 are intended to be ins[...]
-
Page 3
4 SSDTF10xx-10x Installation -- Continued Set the loop-back switch Hardware mode: The loop-back switch is located on the front panel of the device and is used for installation and network debugging procedures. To set the switch, use a small flat-blade screwdriver or a similar device (see the drawing to the right). CL (Copper loop-back) Enable loop-[...]
-
Page 4
6 SSDTF10xx-10x Installation -- Continued Settings for T1 configuration (right switch set, SW 1) T1/long-haul signal Use switches 3 and 4 on the left switch set to select T1/long-haul signal (see the drawing below). Use switches 1 and 2 on the right switch set to select the proper network cable settings. The drawing below lists the four options. -1[...]
-
Page 5
8 SSDTF10xx-10x Installation -- Continued Install the copper cable 1. Locate or build twisted-pair copper cables that are compliant with the specifications on page 11 with RJ-45 connectors at both ends. 2. Ensure that the MDI/MDI-X switch is set according to the network conditions (see page 3) . 3. Connect the RJ-45 connector at one end of cable to[...]
-
Page 6
10 SSDTF10xx-10x Cable Specif ications Fiber cable Single mode fiber (recommended): 9 µm Multimode fiber (recommended): 62.5/125 µm Multimode fiber (optional): 100/140, 85/140, 50/125 µm SSDTF1011-105 850 nm multimode Fiber Optic Transmitter Power: min: -19.0 dBm max: -14.0 dBm Fiber Optic Receiver Sensitivity: min: -32.5 dBm max: -14.0 dBm Link[...]
-
Page 7
12 SSDTF10xx-10x T echnical Specifications For use with Transition Networks Model SSDTF10xx-10x or equivalent Standards: Emissions: CISPR A; Telecordia TR-NWT-001089 (designed to meet; NOT tested) ; FCC Part 68; T1/E1 Physical layer: ITU-T, ANSI, AT&T, and ETSI; European Technical Standard: TBR 12; British Technical Publication: PD 7024 : 1994 [...]
-
Page 8
14 SSDTF10xx-10x 4. Is data transfer failing? YES • Verify the local copper connection by starting a local copper loop-back (hardware mode: set the loop-back switch on the local device to “CL”, software mode: enter the local copper loop-back command) and then use a bit error test unit to run a bit error test. • Verify the local fiber connec[...]
-
Page 9
Compliance Information CISPR22/EN55022 Class A + EN55024 CE Mark FCC regulations This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial[...]