Go to page of
Similar user manuals
-
Ventilation Hood
Venmar 600 cfm
24 pages 2.17 mb -
Ventilation Hood
Venmar ESC270
36 pages 3.95 mb -
Ventilation Hood
Venmar 1200 cfm
24 pages 2.17 mb -
Ventilation Hood
Venmar HRV 2600*
22 pages 4.25 mb -
Ventilation Hood
Venmar HEPA 4100*
22 pages 4.25 mb -
Ventilation Hood
Venmar QDE
36 pages 3.95 mb -
Ventilation Hood
Venmar ESB10
36 pages 3.95 mb -
Ventilation Hood
Venmar 700 cfm
24 pages 2.17 mb
A good user manual
The rules should oblige the seller to give the purchaser an operating instrucion of Venmar HRV 2600*, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.
What is an instruction?
The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Venmar HRV 2600* one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.
Unfortunately, only a few customers devote their time to read an instruction of Venmar HRV 2600*. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.
What should a perfect user manual contain?
First and foremost, an user manual of Venmar HRV 2600* should contain:
- informations concerning technical data of Venmar HRV 2600*
- name of the manufacturer and a year of construction of the Venmar HRV 2600* item
- rules of operation, control and maintenance of the Venmar HRV 2600* item
- safety signs and mark certificates which confirm compatibility with appropriate standards
Why don't we read the manuals?
Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Venmar HRV 2600* alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Venmar HRV 2600*, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Venmar service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Venmar HRV 2600*.
Why one should read the manuals?
It is mostly in the manuals where we will find the details concerning construction and possibility of the Venmar HRV 2600* item, and its use of respective accessory, as well as information concerning all the functions and facilities.
After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.
Table of contents for the manual
-
Page 1
INST ALLA TION INSTR UCTIONS AND USER MANU AL RESIDENTIAL USE ONL Y INST ALLER: LEA VE THIS MANU AL WITH THE HOMEO WNER. HOMEO WNER: USE AND CARE INFORMA TION ON P AGES 18 T O 21. READ AND SA VE THESE INSTR UCTIONS 04313 re v . G MODELS[...]
-
Page 2
ABOUT THIS MANU AL First, we want to cong ratulate you on y our purchase of this excellent unit which will allo w you and y our family to enjo y clean and health y air throughout your home f or years to come! Because of the large amount of models cov ered by this pub lication, the illustrations are typical ones. Some details of your unit ma y be sl[...]
-
Page 3
1. T YPICAL I NST ALLA TIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-6 1.1 HR V 2600, HR 2.6, HEP A 3100, HF 3.1 AND HEP A 4100 U NIT I NST ALLA TIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.1.1 S TA N D A LONE . . . . . . . . . . . . . . . . . . . . . . . [...]
-
Page 4
1. TYPICAL INST ALLA TIONS Installations ma y vary according to the model number and the position in which the unit is installed. Use the f ollowing illustr ations as guidelines to help you decide on ho w your unit will be installed. All the units should be hung from the joists, and installed either v er tically or horizontally . NO TE: F or more d[...]
-
Page 5
1. TYPICAL INST ALLA TIONS (CONT’D)[...]
-
Page 6
All 3 types of installations can be used in the attic (Stand Alone, Central Dr aw P oint or Retur n-Retur n). The example sho wn bel ow i s a Return-Retur n installation (connection to a forced air system). VH0051 - 6 - A por tion of stale air is exhausted to the outside and the rest is dr awn to the unit. Outside fresh air is blended with interior[...]
-
Page 7
- 7 - 2.3 M OUNTING AND S ER VICING C ONSIDERA TIONS • The two f ollowing pictures are showing the minim um clearance needed to open the door completely . 22.5” 15.75” (572 mm) (400 mm) VD0117 VD0116 22” (559 mm) NO TE: A minimum of 8” (203 mm) clearance from an y obstruction on top of the unit is required for the ductwork radius turn. 8?[...]
-
Page 8
- 8 - 3.3 L OCA TING THE U NIT Choose an appropriate location for the unit. • Within an area of the house where the ambient temperature is between 10°C (50°F) and 65°C (149°F) (basement, furnace room, closet, etc.). • So as to provide easy access to the interior of the unit, f or filter maintenance. • Close to an e xter ior wall, so as to[...]
-
Page 9
- 9 - 1. Route the cable from the unit to a con venient location f or the wall control. 2. Loosen the locking scre w (the screw cannot be completely remo ved). 3. Detach the f aceplate from the mounting plate by pulling the bottom par t. If necessar y , bore the mounting holes and inser t anchors. 4. P ass the cable (4 wires) through the opening of[...]
-
Page 10
7. T urn the unit switch knob to OFF position in order to unloc k the door. Unlatch the door and open it. If required, the door can be removed. T o do so , remov e the stopper ( A ) located on the right side of the door hinge. Then, hold the door and hit with your palm its left side . Slide the door to the right to disengage it from the unit. 8. Us[...]
-
Page 11
5.2 H OW TO H ANG THE U NIT Use the 4 chains and springs in the hardware pack pro vided with the unit. According to your needs , you can install the unit either in vertical or hor izontal position. VD0074[...]
-
Page 12
- 12 - 5.3 P LANNING OF THE D UCTWORK All units in this manual are prebalanced. • K eep it simple. Plan for a minimum of bends and joints . • K eep the length of outside insulated duct to a minimum. • Do not v entilate cra wl spaces or cold rooms. Do not attempt to recover the e x haust air from a dryer or a range hood. This w oul d cause clo[...]
-
Page 13
5.4 I NST ALLING N ON -I NSULA TED D UCTS AND R EGISTERS ( CONT ’ D ) 5.4.1 S TA N D A LONE S YSTEM ( AS ILLUSTRA TED IN S ECTION 1.1.1) ( CONT ’ D ) A LL UNITS How to connect the fle xible duct to the unit ports • Using the colored stic ker dot included, identify which duct it is (red dot f or stale airflow and b lue dot for filtered airflo [...]
-
Page 14
5.4 I NST ALLING N ON -I NSULA TED D UCTS AND R EGISTERS ( CONT ’ D ) 5.4.2 C ENTRAL DRA W P OINT ( AS ILLUSTRA TED IN S ECTION 1.1.2) ( CONT ’ D ) Fresh/Filtered air ductwork (Return side connection) (cont’ d) HEP A 3100, HF 3.1 AND HEP A 4100 UNITS ONL Y ( CONT ’ D ) • Fix the duct connector to the f orced air unit duct using its 4 reta[...]
-
Page 15
5.5 I NST ALLING I NSULA TED F LEXIBLE D UCTS Use the f ollowing procedure f or connecting the insulated flexib le ducts to the T andem® transition* ( EXHA UST AIR TO OUTSIDE and FRESH AIR FROM OUTSIDE ). NO TE: If the joist are perpendicular to the ducts, or if the connection to the exterior hood is in a limited area, your installation will need [...]
-
Page 16
5.5 I NST ALLING I NSULA TED F LEXIBLE D UCTS ( CONT ’ D ) 5.5.2 C ONNECTION TO THE 5’ ’ TO 6’ ’ O V AL PORTS OF THE UNIT ( CONT ’ D ) 4. Apply duct tape gently to the joint in order to make an airtight seal. 5. Repeat steps 1 to 4 f or the other 5’ ’ to 6’ ’ por t. See figure beside to find the EXHA UST AIR T O OUTSIDE ( 1 ) an[...]
-
Page 17
5.6 I NST ALLING D UA L E XTERIOR H OOD ( CONT ’ D ) 5.6.3 C ONNECTING T ANDEM ® TRANSITION TO EXTERIOR D UAL H OOD ( CONT ’ D ) 2. Join the end of the T andem transition to the rear of the e xter ior backplate. Secure with 2 Xmas tree pins and seal properly with duct tape. 3. Lean the e xter ior bac kplate to the exterior wall. Using 4 #8 x 1[...]
-
Page 18
6.1 M AIN S WITCH All units are equipped with a 3-position main s witch, located on the front panel. 6.2 40415 AND 40425 W ALL C ONTR OLS D ESCRIPTION The included wall control is 40415 (intented f or HR V 2600, HEP A 3100 and HEP A 4100 units only) or 40425 control (intented for HR 2.6 and HF 3.1 units only). The w all control is in OFF mode when [...]
-
Page 19
6.4 W ALL C ONTROLS C ONFIGURA TION See the configuration tab le below f or the list of configuration parameters. Press the Menu b utton for 3 seconds to enter or e xit the configuration menu. NO TE: The wall control automatically sav es any changes and e xits the configuration menu if no b utton is pressed within the ne xt 60 seconds. Press the Me[...]
-
Page 20
- 20 - 7. MAINTENANCE W ARNING Risk of electrical shocks. Before performing an y maintenance or servicing, al ways disconnect the unit fr om its power source. ! 7.1 B IANNU AL M AINTENANCE ( ESSENTIAL ) P erf or m this maintenance when the Filter Maintenance LED is flashing . F ollow these steps: 1. T urn switch knob to OFF to unloc k the door . 2.[...]
-
Page 21
- 21 - 7.1 B IANNU AL M AINTENANCE ( ESSENTIAL ) ( CONT ’ D ) 6. W ash the 2 core filters under hot water with mild soap . Rinse thoroughly and let dr y completely bef ore reinstalling on the core. Remove the dust on the core using a v acuum cleaner with a soft brush attachment. 1) Core filters 2) Core NO TE: Make sure the damper spring ( 1 ) is [...]
-
Page 22
If the problem is still not solv ed, call your installer or the nearest authorized Service Center . Also , you can reach the Customer Service Depar tment at one of the following telephone n umbers: Exclusively f or models HRV 2600, HEP A 3100 and HEP A 4100: Exclusively f or models HR 2.6 and HF 3.1: 1-800-567-3855. 1-866-737-7770. PROBLEMS SOLUTIO[...]