Westinghouse NB-14w2 manual

www .westinghousedigital.com USER’S MANUAL MANUAL DEL USUARIO NB-14w2 Notebook Computer Westinghouse Digital Electronics Santa Fe Springs, CA SE-UM-1401-0601[...]

i -1[...]

i -2 Notice The information in this user ’s manual is subject to change without notice. THE MANUF ACTURER OR RESELLER SHALL NO T BE LIABLE FOR ERRORS OR OMISSIONS CONT AINED IN THIS MANUAL AND SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL DAMAGES, WHICH MA Y RESUL T FROM THE PERFORMANCE OR USE OF THIS MANUAL. The information in this user ’s manual [...]

i -3 T ABLE OF CONTENTS PREF ACE Symbols and Conventions Protecting Y our Computer - Avoid Abusive Handli ng and Adverse Environment Chapter Summaries 1. GETTING TO KNOW THE BA SICS Performance Features (1-2,3) System at a Glance (1-4) T op View (1-4,5) Front View (1-6) Side Views (1-7,8,9) Bottom View (1-10,1 1) AC Adapter (1-12) LED S tatus Indic[...]

i -4 BIOS Action Keys (2-3) Modifying the BIOS Settings (2-4) Main Setup (2-4) Info Setup (2-4) Advance Setup (2-5) Security Setup (2-5,6) Power Setup (2-6) Boot Setup (2-7) Exit Setup (2-8) 3. BA TTER Y POWER & POWER MANAGEMENT The Battery Pack (3-2) Lithium-Ion Battery T echnology (3-2) Battery Low-Power W arning (3-3) Installing and Removing[...]

i -5 Performance Problems (4-14) Firewire (IEEE1394) and USB2.0 Probl ems (4-15) Additional Questions (4-16) APPENDIX A Product Specification APPENDIX B A gency Regulatory Notices[...]

i -6 Preface Using This Manual This User ’s Manual contains gen eral info rmation about the hardware and sof tware setup, trouble shooting, and technical specifications of the notebook computer . Symbols and Conventions The following conventions and symb ols are used in this manual:  When keys are to be pressed at the same time, a plus (+) sym[...]

i -7 Protecting Y our Computer - Av oid Abusive Handling and Adverse Environment Follow the advice below will help en sure that you get the most out of your Investment. Y our computer will serve you well if you t ake g ood care of it.  Do not expose the computer to direct sunlight or pla c e it near sources of heat.  Do not subject it to temp[...]

i -8  Keep the adapter away from children.  The total ampere ratings of the equipm ent plugged in should not exceed the ampere rating of the cord if you are using an extension cord.  The total current rating of all equipment plugg ed into a single wall outlet should not exceed the fuse rating.  Do not connect other AC adapter to your no[...]

i -9 Chapter Summaries The following is a summary of the available chapters and appendices in this manual . Chapter 1: Getting to Know the Basics In this chapter , you will learn the basic operations and features of your computer . It gives you a general understanding o f the component s of your computer . Chapter 2: BIOS Setup / Security In this c[...]

■ C h a p t e r 1 G e t t i n g T o K n o w T h e B a s i c s 1-1 CHAPTER ▼ ONE GETTING T O KNOW THE BASICS This chapter introduce s the features and component s of the computer .[...]

■ C h a p t e r 1 G e t t i n g T o K n o w T h e B a s i c s 1-2 Performance Features  High Performance Processor w ith A TI Radeon Xpress 200M Chip set The notebook PC is equipped with a po werful Mobile Intel Celeron M processo r . T ogether with the A TI chipset and integrated graphic technologie s, the system offers very advanced PC perfo[...]

■ C h a p t e r 1 G e t t i n g T o K n o w T h e B a s i c s 1-3  Firewire (IEEE1394 / 1394a) and USB2.0 port s In addition to a full array of built-in I/O por t s, the computer offers IEEE1394 for ultra hi gh-sp eed connection to high bandwidt h digital video devices a nd USB2.0 ports to connect to any USB-based peripheral devices.  Wirel[...]

■ C h a p t e r 1 G e t t i n g T o K n o w T h e B a s i c s 1-4 System At A Glance T op V iew 1. LCD Display The panel is whe re the system content is displayed. 2. LED St atus Indicator The LED S tatus indicators reveal the status of the system power state, battery-chargi ng st ate, Instant-On/Su spend state, and the WLAN switch enabling and d[...]

■ C h a p t e r 1 G e t t i n g T o K n o w T h e B a s i c s 1-5 3. Keyboard The keyboard is used to en ter data. (See Keyboard Section for details.) 4. T ouch Pad The touch pad is a built-in pointing device with functions similar to a mouse. 5. Built-in Microphone The built-in microphone record s sound. 6. Silent Mode Button When the system is [...]

■ C h a p t e r 1 G e t t i n g T o K n o w T h e B a s i c s 1-6 Front Vie w W arning: Do not place any heavy objects on the top of notebook. This may damage the display 1. Wireless On/Off S witch Use the Switch to disable or enable the Wireless fun ction. When Wireless LA N function is enabled, the LED st atus indicator shows steady blue light.[...]

■ C h a p t e r 1 G e t t i n g T o K n o w T h e B a s i c s 1-7 Side Vie w s W arning: Do not place any heavy objects on the top of notebook. This may damage the display 1. Optical Drive and Disk Eject Button a nd Manual Eject Key Hole If your computer comes with the Combo drive, DVD-Dual, or Super-Multi drive, you may save data on to a CD-R / [...]

■ C h a p t e r 1 G e t t i n g T o K n o w T h e B a s i c s 1-8 4. Modem Port This is where you plug the phone jack (RJ-1 1) for fax/modem functions. 5. Kensington Lock Key Hole A Kensington-type security lock latche s to this keyhole for anti-theft purpose. 6. USB2.0 Port (x3) The Universal Serial Bus (USB2.0-compliant) port allows you to conn[...]

■ C h a p t e r 1 G e t t i n g T o K n o w T h e B a s i c s 1-9 12. Ethernet / LAN Port The port connect s to a network hub via the RJ-45 cable and also conforms to 10/100Base -TX transmission protocol. 13. V entilation Grill The fan grill is where air is exchanged t o dissipate the internal heat. Do not block this airway completely . 14. TV (S[...]

■ C h a p t e r 1 G e t t i n g T o K n o w T h e B a s i c s 1-10 Bottom Vi ew 1. Battery Pack and Battery Latch The battery pack is a built-in power sou rce for the notebook. Slide the battery latch to release the battery pack. 2. V entilation Grill The fan grill is where air is exchanged t o dissipate the internal heat. Do not block this airwa[...]

■ C h a p t e r 1 G e t t i n g T o K n o w T h e B a s i c s 1-1 1 W arning: Do not block the Fan Grill outlet. Place the machine on hard surface only . The bottom case may get very hot. 3. System Device Cov er The system’ s processor with cooler assembly , Wireless LAN module, HDD, and DDR memory mo dule are located under the case cover . Not[...]

■ C h a p t e r 1 G e t t i n g T o K n o w T h e B a s i c s 1-12 AC Adapter 1. DC-out Connector The DC-out connector docks to the power jack (DC-in) on the computer . 2. Adapter The adapter convert s alternating current into constant DC voltage for the computer . 3. AC Plug The AC plug connects to the AC wall outlet.[...]

■ C h a p t e r 1 G e t t i n g T o K n o w T h e B a s i c s 1-13 LED S tatus Indicator The LED S tatus Indicator d isplays the operating st atus of your notebook. When a certai n function is enabled, an LED will light up. The following section describes it s indication. System & Power S t atus Indicators LED Graphic Symbol Indication Blue l[...]

■ C h a p t e r 1 G e t t i n g T o K n o w T h e B a s i c s 1-14 OSD S tatus Indicator The On-screen S tatus Displ ay Indicator displays the operating status of your notebook. When a cert ain function is enabled, the symbol will show up on windows. The following section describes its i ndication. OSD St atus Indicators Action Graphic Symbol Fn [...]

■ C h a p t e r 1 G e t t i n g T o K n o w T h e B a s i c s 1-15 Keyboard Features Function Keys (Quick Key s) Graphic Symbol Action System Control Fn + F1 Enters Suspend Mode. Fn + F3 T urns of the battery warning beep off or o n. Fn + F4 Changes Display Mode: LCD-only , CRT -only and LCD&CRT . Fn + F5 T urns S peaker V olume up. Fn + F6 T[...]

■ C h a p t e r 1 G e t t i n g T o K n o w T h e B a s i c s 1-16 Windows Keys Y our keyboard also has two Windows keys: 1. S tart Key This key allows you to p ull up the Windows S tart Me nu at the bottom of the taskbar . 2. Application Menu Key This key brings up the popup menu fo r the application, similar to a click of the right mouse button[...]

■ C h a p t e r 1 G e t t i n g T o K n o w T h e B a s i c s 1-17 T ouch Pad The built-in touch pad, which is a PS/2-comp atible pointing device, senses movement on it s surface. As you move your fingertip on the surface of the pad, the cu rsor responds accordingly . The following items teach you how to use the touch p ad: 1. Move your finger ac[...]

■ C h a p t e r 1 G e t t i n g T o K n o w T h e B a s i c s 1-18 Graphic Subsystem Y our computer uses a high performance 14.1-inch active matrix TFT p anel with high resolution and multi -million colors for comfortabl e viewing. The A TI Radeon Xpress 200M integrated video graphics accelerator , which is Mi crosoft DirectX 9 co mpatible, perfo[...]

■ C h a p t e r 1 G e t t i n g T o K n o w T h e B a s i c s 1-19 Opening and Closing the Display Panel T o open the display , lift up the lid. Then tilt it to a comfortable viewing position. The LCD panel has a maximum op ening of 135 degrees. Do not push i t down forcibly . T o close the display cover , fold it down gently . W arning: T o avoi[...]

■ C h a p t e r 1 G e t t i n g T o K n o w T h e B a s i c s 1-20 Audio Subsystem Y our computer ’s audio sub system is Sound Blaster Pro-compatibl e. Adjusting the V olume Manually T o increase the volume, press Fn+F5. T o decrease the volume, press Fn+F6. Adjusting the Audio V olume in Windows 1. Click the speaker symbol in the t ask tray in[...]

■ C h a p t e r 1 G e t t i n g T o K n o w T h e B a s i c s 1-21 Modem Y our computer comes with a 56K V .92 internal fax/modem and a phone jack (RJ-1 1), whi ch is located on the left side of your co mputer . Use a telephone cable to conne ct the computer to the telephone wall outlet. Note: For certain configuration, ther e is no Modem Port or[...]

■ C h a p t e r 1 G e t t i n g T o K n o w T h e B a s i c s 1-22 2. Click on the pull-do wn menu and select the count ry where it is applicable. Click on OK to exit.[...]

■ C h a p t e r 1 G e t t i n g T o K n o w T h e B a s i c s 1-23 Ethernet Y our computer is equipped with a 10/100 Base-TX Fast Ethernet network adapter . Connect the active LAN ca ble to the RJ-45 LAN port located on the left side of the computer . This allows you to access and transmit dat a in the local area network. Connecting to the Net wo[...]

■ Chapter 2 Bios Setup and Security Feature 2-1 CHAPTER ▼ TWO BIOS SETUP AND SECURITY FEA TURE In this chapter , you will learn how to enter the BIOS Setup Menu and manipulate various hardware control settings. Y ou will also learn how to use the built-in security features.[...]

■ Chapter 2 Bios Setup and Security Feature 2-2 The Setup Utility is a hardware conf iguration program built into your computer ’s BIOS (Basic I nput/Output System). It runs a nd maintains a variety of hardware functio ns. It is a menu-driven software, which allo ws you to easily configure and change the settings. The BIOS contains manuf acture[...]

■ Chapter 2 Bios Setup and Security Feature 2-3 Entering the BIOS Setup Screen First turn on the power . When the BIOS performs the POST (Power-On Self T est), press F2 ke y quickly to activate the Pheonix BIOS Setup Utility . Note: Y ou may need to press F2 key fairly quickly . Once the system begins to load Windows, you may have to retry b y cy[...]

■ Chapter 2 Bios Setup and Security Feature 2-4 Modifying the BIOS Settings The Phoenix BIOS setup main menu is subdivided into sub-menus. Each menu item is described in this section. Main Setup Under this menu, you may change time/date and view ba sic processor and system memory inform ation. Item Selections / Sub-menu Description System Time N/[...]

■ Chapter 2 Bios Setup and Security Feature 2-5 Advanced Setup Item Selections / Sub-menu Description Execute Disable Bit Disabled Enabled When enabled, this unique feature protects against certain type of virus that creates Buffer Overflow problem in the memory subsystem. Quiet Boot Disabled Enabled When Disabled, the system will display OEM log[...]

■ Chapter 2 Bios Setup and Security Feature 2-6 provides both a Supervisor and a User password. If you try to activate both passwo rds, the Superv isor p assword must be set first. The passwords activate two diff erent levels of protecti on: 1. System always asks for p assword every time it is powered on. 2. System asks for passwo rd only when yo[...]

■ Chapter 2 Bios Setup and Security Feature 2-7 Boot Setup ► Boot Settings Configuration Item Selections / Sub-menu Description LAN Remote Boot Disabled Enabled When enabled, the system can supp ort remote wake-up or boot on LAN. ► Boot Device Priority Item Selections / Sub-menu Description USB Key USB FDC USB CDROM USB HDD IDE CD IDE HDD PCI[...]

■ Chapter 2 Bios Setup and Security Feature 2-8 Exit Setup Item Selections / Sub-menu Description Saves Changes and Exit N/A After you have completed the BIOS settings, select this item to s ave all settings, exit BIOS Setup utility , and reboot. New system settings will t ake effect on next power-up. F10 key can b e used for this operation. Disc[...]

■ C h a p t e r 3 B a t t e r y P o w e r & P o w e r M a n a g e m e n t 3-1 CHAPTER ▼ THREE BA TTER Y POWER & POWER MANAGEMENT In this chapter , you will learn the fundamentals of power management and how to use it to achieve longer battery life.[...]

■ C h a p t e r 3 B a t t e r y P o w e r & P o w e r M a n a g e m e n t 3-2 In this chapter , you will learn how to operate your no teboo k on battery power , how to handle and maintain the battery p ack, and learn about the system’ s power saving features. TFT display , central processor , hard disk drive are the major hardware subsystem[...]

■ C h a p t e r 3 B a t t e r y P o w e r & P o w e r M a n a g e m e n t 3-3 Battery Low-Power W arning 1. Low Battery W arning Low battery condition occurs when battery power is reduced to 6%. The green battery status LED indicator blinks and the system beep s once every 16 seconds o r so. 2. V ery Low Battery Warning V ery Low battery cond[...]

■ C h a p t e r 3 B a t t e r y P o w e r & P o w e r M a n a g e m e n t 3-4 Installing and Removing the Battery Pack T o Remove the Battery Pack: 1. Place the notebook bottom-side up on a flat and secured surface. 2. Push the latch and pull the battery’s hard case away from the notebook.[...]

■ C h a p t e r 3 B a t t e r y P o w e r & P o w e r M a n a g e m e n t 3-5 T o Install the Battery Pack: 1. Place the notebook bottom-side up on a flat and secured surface. 2. Carefully insert the battery pack into the battery compartment of the notebo ok. Charging the Battery and Charging T ime T o charge the battery , while the battery p[...]

■ C h a p t e r 3 B a t t e r y P o w e r & P o w e r M a n a g e m e n t 3-6 Checking the Battery Level Y ou can check the remaining battery power in the Windows battery status indicator , which i s located at the lower ri ght-hand corner of the task bar . (If you do not see a battery or AC-in icon on the task tray , go to Power Options Prop[...]

■ C h a p t e r 3 B a t t e r y P o w e r & P o w e r M a n a g e m e n t 3-7 Using Windows Power Options Windows Power Manage ment provides basic power saving features. In the Windows Power Options Properties [S tart > Settings > Control Panel > Power Option s] dialogue box, you may enter time-out values for display and hard disk dr[...]

■ C h a p t e r 3 B a t t e r y P o w e r & P o w e r M a n a g e m e n t 3-8 In this dialog box, you can manually set the LCD and hard drive’ s time-out value s in the Plugged in colu mn and in the Running on batteries column. Lower time-o ut values will save more battery power . Note: Also consult Windows user guide for more information o[...]

■ C h a p t e r 3 B a t t e r y P o w e r & P o w e r M a n a g e m e n t 3-9 Suspend Mode St andby Suspend The system automatically enters this mo de af ter a period of inactivity , which is set in the Power Schem es dialog box. In S tandby mode, hardware devices, such as display panel and ha rd di sk, are turned of f to conse rve energy . H[...]

■ C h a p t e r 3 B a t t e r y P o w e r & P o w e r M a n a g e m e n t 3-10 Note: Do not install or remove the memory module when the system is in the suspend mode. Note: Actual dialogue box shown above ma y appear slightly dif ferent.[...]

■ C h a p t e r 3 B a t t e r y P o w e r & P o w e r M a n a g e m e n t 3-1 1 Power Button Action The notebook PC’ s power button can be set to turn of f the system or activate the suspend mode. Go to [S tart > Settings > Control Panel > Power Options] and click on the Advanced tab. In the pull-do wn menu, select how you wish the[...]

■ C h a p t e r 3 B a t t e r y P o w e r & P o w e r M a n a g e m e n t 3-12 Low Battery W arning Y ou can define when and how the syste m warns you of its battery-lo w condition. Go to the Alarms tab in the Power Options Propertie s box. If you wish to hear audible beep s, click on the Alarm Action button and put a check on Sound Alarm. No[...]

■ C h a p t e r 3 B a t t e r y P o w e r & P o w e r M a n a g e m e n t 3-13 Power Menu Quick Access Instead of making specific sele ction s in the Power Options Properties box, you can quickly and ea sily specify which pre-set power saving fun ction you desire by clicking on the Battery icon at the lower right-hand corner of the task bar .[...]

■ Chapter 4 T roubleshooting 4-1 CHAPTER ▼ FOUR TROUBLESHOOTING In this chapter , you will learn how to solve common hardware and sof tware problems.[...]

■ Chapter 4 T roubleshooting 4-2 Y our computer has been fully tested and complies with the system specifications befor e ship ping. However , incorrect operations and/or mishandling may caus e problems. This chapter provides a reference for ide ntifying and correcting common hardware and sof tware problems that you may encounter . When you encou[...]

■ Chapter 4 T roubleshooting 4-3 changes you made, try to restore all the settings to factory defaults.  Be sure all the device drivers are inst all ed properly . For example, without the audio driver properl y inst alled, the speakers and micro phone will not work.  If external devices such as USB came ra , scanner , and printer do not fun[...]

■ Chapter 4 T roubleshooting 4-4 Audio Problems No speaker output -  Software volume cont rol is turned down in Microsoft Sound System or is muted. Double-cli ck the speaker icon on the lower right corner of the taskbar to see if the speaker has been muted o r turned down all the way .  Most audio problems are sof tware-related. If your com[...]

■ Chapter 4 T roubleshooting 4-5 Hard Disk Problems The hard disk drive does not work or is not recognizable -  The new HDD may need to be partitioned and reformatted. O/S and drivers will need to be re-inst alled as well.  Check the hard disk indicat or LED. When you access a file, the LED lamp should light up moment arily .  The new HD[...]

■ Chapter 4 T roubleshooting 4-6 The hard disk t akes longer to read a file -  If you have b een using the drive for a period, the files may be fragmented. Go to [S tart > Programs > Accessories > System T ools > Disk Defragmenter] to perform a disk defragment ation. This operation may take a while.  Interrupt request s or probl[...]

■ Chapter 4 T roubleshooting 4-7 Optical Drive Problems The optical drive does not work -  T r y rebooting the system.  The disk is damaged or files are not re adabl e.  After you have inserted a CD-ROM disk, it may take a moment before you can access it s content. The drive dose not read any disks -  The CD may not be properly seated[...]

■ Chapter 4 T roubleshooting 4-8 Display Problems The display p anel is blank when the system is turned on -  Make sure the computer i s not in the S tandby or Hibernate suspend mod es. The display is turned of f to conserve energy in these modes. The screen is difficult to read -  The display resolution should at least be set to at least10[...]

■ Chapter 4 T roubleshooting 4-9 Keyboard and Mouse Problems The built-in touch p ad performs erratically  Make sure there is no excess perspi ration or humidity on your hand when using the t ouc h p ad. Ke ep the surfa ce of the touch pad clean a nd dry .  Do not rest your palm or wr ist on the surface of the touch pad while typing or u si[...]

■ Chapter 4 T roubleshooting 4-10 CMOS Battery Problem A message “CMOS Checksum Failure” display s during the booting process or the ti me (clock) reset s when booting -  T ry to reboot the system.  If the message “CMOS Checksum Failu re” appears during the booting procedure even af ter rebooting, it may indicate failure of the CMOS[...]

■ Chapter 4 T roubleshooting 4-1 1 Memory Problems The POST does not show an increased memory capacity when you have already inst alled additional memory -  Certain brand s of memory module m ay not be compatible wi th your system. Y ou should ask your vendor for a list of compatible DIMM.  The memory module may be defective. The O/S issues[...]

■ Chapter 4 T roubleshooting 4-12 Modem Problems The built-in modem does not respond -  Make sure the modem driver is loa ded p roperly .  Go to [S tart > Settings > Control Panel > Phone and Modem Options] and go to Modems t ab. Make sure Motorola SM56 Data Fax Modem i s listed. Otherwise, click the Add button to add t he modem dr[...]

■ Chapter 4 T roubleshooting 4-13 Network Adapter / Ethernet Problems The Ethernet adapter does not w ork -  Go to [S tart > Settings > Control Panel > System > Hardware > Device Manager]. Double-click on Network Adapters and check if Re al tek RTL8139/810x Family Fast Ethernet NIC appears as one of the adapters. If it does not [...]

■ Chapter 4 T roubleshooting 4-14 Performance Problems The computer becomes hot -  In a 35 o C environment, the cert ain areas of the computer ’ s b ack ca se are expected to reach 50 degrees.  Make sure the air vent s are not blocked.  If the fan does not seem to be working at high temperature (50 degrees Celsius an d up ), contact th[...]

■ Chapter 4 T roubleshooting 4-15 Firewire (IEEE1394) and USB2.0 Problems The USB device does not w ork -  Windows NT 4.0 does not support USB protocol s  Check the settings in the Windows Control Panel.  Make sure you have inst alled the necessary devi ce drivers.  Contact the d evice vend or for additional support. The IEEE1394 port[...]

■ Chapter 4 T roubleshooting 4-16 Additional Questions  See our website at www.westinghoused i gital.com.  Contact Westinghouse Digital Customer Service at (866) 287-5555 or write u s service@westinghousedigital.com .[...]

■ Appendix A Product Specific ation A -1 APPENDIX ▼ A PRODUCT SPECIFICA TION[...]

■ Appendix A Product Specific ation A -2 ▼ Processor and Core Logic Mobile Intel Celer on M Processor (Yon ah), up to 1.73GHz, 1MB L2 cache A TI RC410MD + A TI SB460 chipset with graphic, audio, modem, and USB2.0 controllers integrated 533MHz Front Side Bus 533 / 667MHz DDR2 interface ▼ System Memory DDR2 SDRAM 533 / 667 256 / 512 / 1024MB T [...]

■ Appendix A Product Specific ation A -3 ▼ Audio A TI SB460 integrated audio controller Realtek Audio Codec DirectSound 3D, EAX 1.0 & 2.0 compatible A3D, I3DL2 compatible AC97 V2.3 compatible Azalia compatible 2 S tereo S peakers ▼ Modem A TI SB460 integrated Modem Cont roller with MDC card, support 56K MDC Modem Card with Azalia standard[...]

■ Appendix A Product Specific ation A -4 ▼ LAN / Ethernet Realtak RTL8100CL Ethernet function f or 10/100Base-TX network standard s Windows XP Plug and Play compatible Automatic Jam and auto-negotiation for flow control Auto Negotiation and Parallel detectio n for automatic speed selection (IEEE 802.3u) High performance 32-bit PCI bus master ar[...]

■ Appendix A Product Specific ation A -5 ▼ Keyboard & T ouch pad 86/87-key QWERTY keyboard with numeric keyp ad and Windows keys, 19.05mm Pitch Built-in T ouch Pad ▼ ExpressCard (NewCard) & Multiple Card Reader 02 Micro 0Z128 (Card Reader) Single Slot, 34mm type I supported Multimedia Card (MMC), Secu re Digital Card (SD ), Memory S t[...]

■ Appendix A Product Specific ation A -6 ▼ Battery Pack / AC Adapter Li-ion 6-Cell pack, 10.8V / 1 1.1V x 4000 mAH or Li-ion 6-Cell pack, 10.8V / 1 1.1V x 4400 mAH or Li-ion 6-Cell pack, 10.8V / 1 1.1V x 4800 mAH Low battery state with low battery warning beep Uniwill SmartPower III Power Management Smart Battery Compliant; low battery warning [...]

■ Appendix A Product Specific ation A -7 ▼ Physical Specification 332 (W) x 232 (D) x 23.5~33.8 (H) mm 2.4KG / 5.28lbs (with 14.1” LCD, DVD-ROM Drive an d 6-cell battery pack) Operating T emperature: 5 to 35 o C (41 to 95 o F) Operating Humidity: 20 to 80 percent RH (5 to 35 o C) S torage T emperature: -15 to 50 o C (-5 to 122 o F)  Dimens[...]

■ Appendix B A gency Regulato ry N otices B-1 APPENDIX ▼ B AGENCY REGULA TOR Y NOTICES[...]

■ Appendix B A gency Regulato ry N otices B-2 Federal Communications Commission Notice This equipment has bee n tested an d found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasona ble prot ection against har mful interference in a residential installation. Th[...]

■ Appendix B A gency Regulato ry N otices B-3  EN55022 : 1998+A1: 2000+A2: 2003, CLAS S B  EN61000-3-2 : 2000  EN61000-3-3 : 1995+A1: 2001  EN55024 : 1998+A1 : 2001+A1: 2003  IEC61000-4-2: 2001  IEC61000-4-3:200 2+A1:2002  IEC61000-4-4:199 5+A1:2000+A2:2001  IEC61000-4-5:200 1  IEC61000-4-6:200 1  IEC61000-4-8:200 1 [...]

■ Appendix B A gency Regulato ry N otices B-4 Att achment Limitations St atement '' Notice: This equipment meets telecommu ni cations network protective, operational and safet y requir ements as pre scribe d in the appropriate Terminal Equipment T echnical Requirements document(s). This is confirmed by marking the equipment wi th the In[...]

■ Appendix B A gency Regulato ry N otices B-5  The cord set must have a rated current capacity of at least 10 A.  The attachment plug must be an earth-grounding t ype with a NEMA 5-15P (15A, 125V) or NEMA 6-15P (15 A, 250V) configuration. Japan  All components of the cord set (cord, connector , and plug) must bea r a `PSE` mark and regis[...]

■ Appendix B A gency Regulato ry N otices B-6  The cord set must have a current capacity of at least 10 A and a nominal voltage rating of 125 / 250 V AC. CAUTION: MODEL NB-14w2 IS DESIGNED T O USE WITH THE FOLLOWING AC ADAPTER MODEL ONL Y Manufacture: LITE-ON ELECTRONICS, INC Model: P P A-1650-02 (65W), P A-1650-01 (65W) Manufacture: LI SHIN I[...]

■ Appendix B A gency Regulato ry N otices B-7 only with same or equivale nt typ e recommended by the manufacturer . Discard used batteries according to the manufacturer ’s instructions or local laws. VORSICHT! Explisionsgefa hr bei unsachgernazen Austausch der Batterie. Ersatz nur durch denselben oder ei nem vom Hersteller empfohlenem ahnlichen[...]

■ Appendix B A gency Regulato ry N otices B-8 Discard used batteries according to the manu f acturer ’s instructions. A TTENTION: Il y a danger d’xplosion s’il y a remplac eme nt incorrect d e la batterie. Remplacer uniquement a vcc unc batterie du meme type ou d’un type recommande par le constructer . Mettre au rebut les batteries usag e[...]

www .westinghousedigital.com USER’S MANUAL MANUAL DEL USUARIO NB-14w2 Notebook Computer Westinghouse Digital Electronics Santa Fe Springs, CA SE-UM-1401-0601[...]