Go to page of
Similar user manuals
-
Heat Pump
White Rodgers 90 SERIES
8 pages 0.13 mb -
Heat Pump
White Rodgers 1F95-391
12 pages 0.16 mb -
Heat Pump
White Rodgers 1F84-51
8 pages 0.11 mb -
Heat Pump
White Rodgers 1F95CA-391
12 pages 0.15 mb -
Heat Pump
White Rodgers 1F82-261
2 pages 0.21 mb -
Heat Pump
White Rodgers 1F58-72
6 pages 0.12 mb -
Heat Pump
White Rodgers 70 Series
2 pages 0.32 mb -
Heat Pump
White Rodgers 1F59-13
4 pages 0.12 mb
A good user manual
The rules should oblige the seller to give the purchaser an operating instrucion of White Rodgers 1F84-51, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.
What is an instruction?
The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of White Rodgers 1F84-51 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.
Unfortunately, only a few customers devote their time to read an instruction of White Rodgers 1F84-51. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.
What should a perfect user manual contain?
First and foremost, an user manual of White Rodgers 1F84-51 should contain:
- informations concerning technical data of White Rodgers 1F84-51
- name of the manufacturer and a year of construction of the White Rodgers 1F84-51 item
- rules of operation, control and maintenance of the White Rodgers 1F84-51 item
- safety signs and mark certificates which confirm compatibility with appropriate standards
Why don't we read the manuals?
Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of White Rodgers 1F84-51 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of White Rodgers 1F84-51, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the White Rodgers service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of White Rodgers 1F84-51.
Why one should read the manuals?
It is mostly in the manuals where we will find the details concerning construction and possibility of the White Rodgers 1F84-51 item, and its use of respective accessory, as well as information concerning all the functions and facilities.
After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.
Table of contents for the manual
-
Page 1
To prevent electrical shock and/or equipment damage disconnect electric power to system at main fuse or circuit breaker box until installation is complete. Do not use on circuits exceeding specified voltage. Higher voltage will damage control and could cause shock or fire hazard. Do not short out terminals on gas valve or primary control to test. S[...]
-
Page 2
2 INST ALLA TION REMOVE OLD THERMOSTAT 1. Shut off electricity at the main fuse box until installation is complete. Ensure that electrical power is disconnected. 2. Remove the front cover of the old thermostat. With wires still attached, remove wall plate from the wall. If the old thermostat has a wall mounting plate, remove the thermostat and the [...]
-
Page 3
3 NOTE NOTE Relay contacts shown are thermostatically operated. The following wiring diagrams show typical terminal identifica- tion and wiring. For proper installation, refer to the original manufacturer's instructions. L R E 24 VAC 120 VAC Hot MALF FAN ON EMERGENCY SYSTEM MONITOR SWITCH FAN AUTO Heat or Cool FAN AUTO Emer Neutral THERMOSTAT [...]
-
Page 4
4 Heating System 1. Move SYSTEM switch to HEAT position. If the auxiliary heating system has a standing pilot, be sure to light it. 2. Press to adjust thermostat setting to 90 ° and hold for five seconds. Both stages of the heating system should begin to operate. However, if the word HEAT is flashing, the com- pressor lockout feature is operating [...]
-
Page 5
5 OPERA TION Before you begin programming your thermostat, you should be familiar with its features and with the display and the location and operation of the thermostat buttons. Your thermostat consists of two parts: the thermostat cover and the base . To remove the cover, gently pull it straight out from the base. To replace the cover, line up th[...]
-
Page 6
6 • RESET BUTTON - (see fig. 2) resets the thermostat pro- gram to the factory setting. This button can be used if you do not like the program you have entered or if you wish to start over in the programming procedure. The reset button can also be used to reset the program if the thermostat has been subjected to a voltage spike and the program ha[...]
-
Page 7
7 Monday Tuesday Wednesday Thursday Friday Saturday Sunday Heating/Cooling Schedule Plan THIS THERMOSTAT ALLOWS ONE SET OF TIMES FOR BOTH HEATING AND COOLING Time Heat Temp. Cool Temp. Time Heat Temp. Cool Temp. Time Heat Temp. Cool Temp. Time Heat Temp. Cool Temp. Period 4 Period 3 Period 2 Period 1 Enter Heating/Cooling Times and Heating Temperat[...]
-
Page 8
6. Repeat steps 3 and 4 to select the start time and heating temperature for Monday’s 2nd heating/cooling period. 7. Repeat steps 3 through 5 for Monday’s 3rd and 4th heating/ cooling period. Monday’s heating program is now complete. If you are programming your thermostat for the first time, and you want programming for all days of the week t[...]