Aastra Telecom RN-001029-00 manual

Release Note Release 2.2 SI S I P I I P PHONE P H O N E 51i, 53i, 55i, 57i, and 57i CT 51 i, 5 3i , 55i , 57 i, a nd 57 i CT RN-001029-00 Rev 06[...]

Aastra T elecom will not accept liability for any da mages and /or long distance charges, which result from unauthorized and/or unlawful use. While every ef fort has been made to ensure accuracy , Aastra T elecom will not be liable for technical or editorial errors or omissions contained within this documentation. The info rmation contained in thi [...]

RN-001029-00, Rev 06, Release 2.2 iii C o n t e n t s Contents General Information ...................... ................... ................ ................ .................... ........... 2 Release Content Information ................. ................... ................ ................... ............... 2 Hardware Supported ...............[...]

iv RN-001029-00, Rev 06 , Release 2.2 C o n t e n t s BroadSoft Interoperability Fe atures ................ ................ ................. ................ ....... 126 CMS Support ..... .................... ................ ................ ................ .................... ....... 126 Server-Side Do Not Disturb (DND), Call Forward (CFWD) ,[...]

RN-001029-00, Rev 06, Relea se 2.2 1 SIP IP Phone Models 51i, 53i, 55i, 57i, and 57i CT Release Note 2.2 About this Document This document provides an overview of the 2.2 features on the 5i Series phones (51i, 53i, 55i, 57i, and 57i CT). For more detailed information about the features associat ed with each phone, and for information on how to use [...]

General Information 2 RN-001029-00, Rev 06, Release 2.2 IP Phone Release Notes 2.2 General Information Release Content Information This document provides release content in formation on the Aastra 51i, 53i, 55i, 57i, and 57i CT SIP IP phone firmware. Hardware Supported This release of firmware is compatible with the following Aastra IP portfolio pr[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 3 5i Series IP Phone Release Notes Features in Release 2.2 Description This section describes the new features includ ed in Release 2.2 of the 5i Series IP Phones. The following table specifies th e 2.2 Features and provides the page number for each feature. Feature Page Number Usability Fe[...]

Features i n Release 2.2 4 RN-001029-00, Rev 06, Release 2.2 IP Phone Release Notes 2.2 BroadSoft Interope rability Feature s CMS Support page 126 Server-Side Do Not Disturb (DND), Call Forward (CFWD) , and Automati c Call Distribution (ACD) Support page 130 Feature Page Number[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 5 5i Series IP Phone Release Notes Usability Features Dial Plan Support for Secondary Dial T one The IP phones now support a feature that allows the user to dial a predefined dial string, obtain a dial tone, and contin ue dialing. A User or Administrator can configure this using the existin[...]

Features i n Release 2.2 6 RN-001029-00, Rev 06, Release 2.2 IP Phone Release Notes 2.2 Account-Based Do Not Disturb (DND) and Ca ll Forward (CFWD) In previous releases of the IP Phone, you could configure a DND key to set “do not disturb” on all the lines on the phone. Also in pre vious releases, you could configure CFWD on all lines (global s[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 7 5i Series IP Phone Release Notes The following describes the soft key behavior for each DND mode. • Account - DND key toggles the a ccount in focus on the IP Phone UI, to ON or OFF if DND enabled for that account. • Phone - DND key toggles all accounts on the phone to ON or OFF . • [...]

Features i n Release 2.2 8 RN-001029-00, Rev 06, Release 2.2 IP Phone Release Notes 2.2 Configuring DND Using the Configuration Files Y ou use the following parameters to configure DND on the IP Phone: • dnd key mode • softkeyN type, topsoftk eyN type, prgkeyN type, or expmodX keyN type • softkeyN states (optional) Y ou use the following para[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 9 5i Series IP Phone Release Notes Example The following is an example of co nfiguring the mode for DND in the configuration files: dnd key mode: 2 softkey1 type: dnd softkey1 states: idle connected inco ming outgoing busy In the above example, softkey 1 is conf igured for DND for line 1 on[...]

Features i n Release 2.2 10 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 Configuring DND Using the Aastra W eb UI Use the following procedure to co nfigure DND mode using the Aastra W e b UI: Aastra Web UI 1 Click on Basic Se ttings->Preferences->General. . 2 In the “ DND Key Mode ” field, sel ect a “do not di sturb” [...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 11 5i Series IP Phone Release Notes 3 Click to save your changes. The change takes effect immediately without a reboot. 4 Click on Basic Settings->Acc ount Configuration. . 5 For each account, enable DND by placing a check mark in the box. Disable DND by unchecking the box. Notes : 1. If[...]

Features i n Release 2.2 12 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 6 Click to save your changes. The change takes effect immediately without a reboot. 7 Click on Operation->Softkeys and XML ; or Click on Operation->Programmab le Keys; or Click on Operation->Expansion Module . Note: If there is no DND key configured o[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 13 5i Series IP Phone Release Notes Using DND Modes via the IP Phone UI If you add a DND key using the config uration files or the Aastra W eb UI, you can toggle the DND state using the IP Phon e UI. Use the following procedure to enable/disable DND on the IP Phone. The following procedure [...]

Features i n Release 2.2 14 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 . Aastra IP Phone UI Ste p Action DND in Account Mode On the 51i and 53i: With the account in focus on the IP Phone UI, press the DND key to toggle DND ON or OFF for the account. Use the RIGHT and LEFT arrow keys to scroll through each account. In the above ex[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 15 5i Series IP Phone Release Notes DND in Phone Mode On the 51i and 53i: Press the DND key to toggle DND ON or OFF for all accounts on the phone. T oggling to ON enables DND on all accounts on the phone. T oggling to OFF disables DND on al l accounts on the phone. Use the RIGHT and LEFT ar[...]

DND in Custom Mode On the 51i and 53i: Press the DND key on the phone. The screen displays a lis t of the accounts on the phone and allows you to enable/disable a specific accoun t or all ac counts. Use th e UP and DOWN arrow keys to scroll through the accounts. In the above exampl e, Screenname1 and 3 have DND ON as indicate d by a checkmark ( 3 )[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 17 5i Series IP Phone Release Notes DND in Custom Mode (continued) On the 55i, 57i, and 57i CT : Press the DND key on the phone. The screen displays a lis t of the accounts on the phone and allows you to enable/disable a specific accoun t or all ac counts. Use th e UP and DOWN arrow keys to[...]

Features i n Release 2.2 18 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 CFWD Account-Based Configuration Call Forward (CFWD) on the IP phone allo ws incoming calls to be forwarded to another destination. Previous to Release 2.2, you could conf igure CFWD on all lines (global settings) or on specific lines (local settings) on th e [...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 19 5i Series IP Phone Release Notes In previous releases, you could configure one phone number and then select the current mode (All, Off, Busy , No Answer, Busy No Answer). In Release 2.2, you can enable different call forwarding rule s/modes independently (for exam ple, you can set differ[...]

Features i n Release 2.2 20 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 Important Notes • In the configuration files, the new “ call forward key mode ” parameter listed in the section “Configuring CFWD Using th e Configuration Files” , is in addition to the previous call forward parameter ( call forward disabled ). Y ou [...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 21 5i Series IP Phone Release Notes Configuring CFWD Using the Con figuration Files Y ou use the following parameters to set CFWD on the IP Phone using the configuration files: • call forward key mode • softkeyN type, topsoftk eyN type, prgkeyN type, or expmodX keyN type • softkeyN st[...]

Features i n Release 2.2 22 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 Parameter – call forward key mode Aastra Web UI: Basic Settings->Preferences->Ge neral Configuration Fi les aastra.cfg, <mac>.cfg Description Sets the mode for how the phone uses “call forwarding” (CFWD) • account The account mode allows yo[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 23 5i Series IP Phone Release Notes Y ou use the following p a rameters to configure a CFWD key and number of rings: • softkeyN type, topsoftk eyN type, prgkeyN type, or expmodX keyN type • softkeyN states (optional) Example The following is an example of co nfiguring the mode for CFWD [...]

Features i n Release 2.2 24 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 Configuring CFWD Using the Aas tra Web UI Use the following procedure to configur e CFWD mode u sing the Aastra W eb UI: Aastra Web UI 1 Click on Operation->Softkeys and XML ; or Click on Operation->Programmab le Keys; or Click on Operation->Expansion[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 25 5i Series IP Phone Release Notes 3 Click on Basic Se ttings->Preferences->General. . Note: If there is no CFWD key configured on the phone or it is removed, you can still set the CFWD modes via the IP Phone UI at the path Options->Call Forward. Aastra Web UI Call Forward Key Mod[...]

Features i n Release 2.2 26 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 4 In the “ Call Forward Ke y Mode ” field, select a call forward mode to use on the phone. V alid values are: Account, Phone, Custom. Default is Account . • account The account mode allows you to configure CFWD on a per account basis. Pressing a configur[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 27 5i Series IP Phone Release Notes 6 Click on Basic Settings->Acc ount Configuration. . 7 For each account, enable CFWD state by placing a check mark in one or more of the following “ Stat e ” fields: •A l l •B u s y • No Answer The “ All ” option forwards all in coming ca[...]

Features i n Release 2.2 28 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 8 For each account, i n the “ Number ” field, enter the phone number for which you want the incoming calls to forward to if th e phone is in the specified state. If using th e “ Account ” mode or “ Custom ” mode, you can enter di fferent phone numb[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 29 5i Series IP Phone Release Notes Using CFWD Modes via the IP Phone UI If you enable/disable CFWD using the configuration files or the Aastra W eb UI, you can use the CFWD screens that displa y to the IP Phone U I. Y ou can access the CFWD parameters by pressing a configured CFWD key (if [...]

Features i n Release 2.2 30 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 . Aastra IP Phone UI Ste p Action CFWD in Account M ode (51i and 53i) 1U s e t h e RIGHT and LEF T arrow keys to scroll through each account. In the above exampl e, Screenname1, Screen name2, and Scree nname3, are three accounts configured on the phone. Screen[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 31 5i Series IP Phone Release Notes 3 Select a state for the account(s) in focus using the UP and DOWN arrow keys. Y ou can enable/disable any or all of the following states for an account: • All - Enables CFWD All for an account and forwards all incoming calls for that account, to the sp[...]

Features i n Release 2.2 32 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 7 In the CFWD S tat e screen, press the DOWN arrow key to scroll to the CFWD Number screen and press CHANGE . 8 Enter a phon e number to apply to th e current st ate in focus. When the phone is in the state you specified, and a call comes into the phone, it fo[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 33 5i Series IP Phone Release Notes 10 For the CFWD No Answer state, In the CFWD Number screen, press the DOWN arrow key to scroll to the CFWD No. Rings screen and press CHAN GE . 1 1 Press the NEXT key to select the number of rings to apply to the phone for call forwarding incoming calls. [...]

Features i n Release 2.2 34 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 14 Press # to confirm the change(s) each time the “Apply Cha nges” screen displays. All changes are saved to the phone. Aastra IP Phone UI Ste p Action[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 35 5i Series IP Phone Release Notes CFWD in Phone Mode (51i and 53i) 1U s e t h e RIGHT and LEF T arrow keys to scroll through each account. In the above exampl e, Screenname1, Screen name2, and Scree nname3, are three accounts configured on the phone. All three accounts have CFWD enable d [...]

Features i n Release 2.2 36 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 2 Press the Call Forward key . The Call Forward Mo de screen displays. Use the UP and DOWN arrow keys to scroll through each state type. In the above exampl e, the account has CFWD All and CFWD NoAns enabl ed as indicated by a checkmark ( 3 ). The CFWD Busy se[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 37 5i Series IP Phone Release Notes 3 Select a state using the UP and DOWN arrow keys. Y ou can enable/disable a specific account on the phone with any or all of the following states. However , the configuration you set will ap ply to all accounts on the phone. • All - Enables CFWD All on[...]

Features i n Release 2.2 38 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 5 Press the CHANGE key in the CFWD S tate screen. Press NEXT to toggle the state of the CFWD state ON or OFF . In the example in S tep 4, you press NEXT to change the option to OFF . 6 Press the SET key to save the change. 7 In the CFWD S tat e screen, press t[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 39 5i Series IP Phone Release Notes 10 For the CFWD No Answer state, in the CFWD Number screen, press the DOWN arrow key to scroll to the CFWD No. Rings screen and press CHAN GE . 1 1 Press the NEXT key to select the number of rings to apply to the phone for call forwarding incoming calls. [...]

Features i n Release 2.2 40 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 14 Press # to confirm the change(s) each time the “Apply Cha nges” screen displays. All the same changes are saved to all accounts on the phone. Aastra IP Phone UI Ste p Action[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 41 5i Series IP Phone Release Notes CFWD in Custom Mode (51i and 53i) 1U s e t h e RIGHT and LEF T arrow keys to scroll through each account. In the above exampl e, Screenname1, Screen name2, and Scree nname3, are three accounts configured on the phone. All three accounts have CFWD enable d[...]

Features i n Release 2.2 42 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 2 Select an account to configure. Press the CHANGE key . The CFWD Mode screen displays. Use the UP and DOWN arrow keys to scroll through each state screen.. In the above exampl e, the account has CFWD All and CFWD NoAns enabled as indicated by a checkmark ( 3 [...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 43 5i Series IP Phone Release Notes 3 Select a state for the account(s) in focus using the UP and DOWN arrow keys. Y ou can enable /disable any or all of the following states for a specifi c account or for all accounts (with individual configurations): • All - Enables CFWD All for an acco[...]

Features i n Release 2.2 44 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 5 Press the CHANGE key in the CFWD S tate screen. Press NEXT to toggle the state of the CFWD state ON or OFF . In the example in S tep 4, you press NEXT to change the option to OFF . 6 Press the SET key to save the change. 7 In the CFWD S tat e screen, press t[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 45 5i Series IP Phone Release Notes 10 For the CFWD No Answer state, in the CFWD Number screen, press the DOWN arrow key to scroll to the CFWD No. Rings screen and press CHAN GE . 1 1 Press the NEXT key to select the number of rings to apply to the phone for call forwarding incoming calls. [...]

Features i n Release 2.2 46 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 13 Press DONE to save CFWD All Number , CFWD All S t ate, CFWD Busy Number , CFWD Busy S tate, CFWD No Answer Number , CFWD No Answer S tate, CFWD No Answer Rings. Each time you press DONE , the following “Apply Changes” screen displays. 14 Press # to conf[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 47 5i Series IP Phone Release Notes . Aastra IP Phone UI Ste p Action CFWD in Account Mode (55i, 57i, and 57i CT) 1U s e t h e RIGHT and LEF T arrow keys to scroll through each account. In the above exampl e, Screenname1, Screen name2, and Scree nname3, are three accounts configured on the [...]

Features i n Release 2.2 48 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 3 Select a state for the account(s) in focus using the UP and DOWN arrow keys. Y ou can enable/disable any or all of the following states for an account: • All - Enables CFWD All for an account and forwards all incoming calls for that account, to the specifi[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 49 5i Series IP Phone Release Notes 4 For the CFWD No Answer state, press the CHANGE key for the mod e you selected i n step 2. This displays the Call Forward S tate screen. In the following example, the CFWD All state is ON.. Note: Y ou can press the AllAcct s key to co py the settings in [...]

Features i n Release 2.2 50 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 5 Press the CHANGE key in the CFWD St ate screen. With th e cursor in the “ St a te ” field, toggle the state ON and OFF by pressing the CHANGE key . Note: Y ou can press the AllAcct s key to co py the settings in the current Call Forward Settings screen f[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 51 5i Series IP Phone Release Notes CFWD in Phone Mode (55i, 57i, and 57i CT) 1U s e t h e RIGHT and LEF T arrow keys to scroll through each account. In the above exampl e, Screenname1, Screen name2, and Scree nname3, are three accounts configured on the phone. Sc reenname1, 2 a nd 3 have ?[...]

Features i n Release 2.2 52 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 3 Select a state for the phone using the UP and DOWN arrow keys. Y ou can enable/disable a specific account on the phone with any or all of the following states. However , the configuration you set will ap ply to all accounts on the phone. • All - Enables CF[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 53 5i Series IP Phone Release Notes 4 In the CFWD No Answer state, press the CHANGE key for the mode you sele cted in st ep 2. This displays the Call Forward S tate screen. In the following example, the CFWD All state is ON.. 5 Press the CHANGE key in the CFWD St ate screen. With th e curso[...]

Features i n Release 2.2 54 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 6U s e t h e DOWN arrow key to scroll to the “ Num ber ” field. Enter a phone number to apply to the current state in focus. When the phone is in the state you specified, and a call comes into the phone, it forwards the call to the number you specify . Use[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 55 5i Series IP Phone Release Notes CFWD in Custom Mode (55i, 57i, and 57i CT 1U s e t h e RIGHT and LEF T arrow keys to scroll through each account. In the above exampl e, Screenname1, Screen name2, and Scree nname3, are three accounts configured on the phone. Screenname1 has “ CFWD All [...]

Features i n Release 2.2 56 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 3 Select an account using the UP a nd DOWN arrow keys. Y ou can also use the follow ing keys if required: All Off Key - Disables CFWD for all accoun ts on the phone. All On Key - Enables C FWD for all accounts on the phone . CopytoAll Key - Copies all settings[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 57 5i Series IP Phone Release Notes 5 Select a state for the selected account(s) using the UP and DOWN arrow keys. Y ou can enable /disable any or all of the following states for a specifi c account or for all accounts (with individual configurations): • All - Enables CFWD All for an acco[...]

Features i n Release 2.2 58 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 6 Press the CHANGE key for the mode you sele cted in step 4. This displays the Call Forward S tate screen. In the following example, th e CFWD All state is ON.. Note: Y ou can press the AllAcct s key to co py the settings in the current Call Forward Settings s[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 59 5i Series IP Phone Release Notes 7 Press the CHANGE key in the CFWD St ate screen. With th e cursor in the “ St a te ” field, toggle the state ON and OFF by pressing the CHANGE key . Note: Y ou can press the AllAcct s key to co py the settings in the current Call Forward Settings scr[...]

Features i n Release 2.2 60 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 Multicast Group Paging An Administrator or User can configure a specific softkey on the phone that allows you to send/receive a Real Time T ransport Protocol (R TP) stream to/from pre-configured multicast address(es) with out involving SIP signaling. This is c[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 61 5i Series IP Phone Release Notes The recipient can d rop the incoming page if required. The recipient can also set Do Not Disturb (DND) to i gnore any incoming pages. For incoming R TP multicasts, the ring ing display is dependant on the “ Allow Barge-In ” parameter . If this paramet[...]

Features i n Release 2.2 62 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 Configuring Group Paging R TP Settings Receiving End of Page Using the Configuration Files Use the following parameters to configur e R TP streaming on the receiving end for Paging applications usin g the configuration files. • paging group listening. Parame[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 63 5i Series IP Phone Release Notes Receiving End of Page Using the Aastra W eb UI Use the following procedure to configure R TP streaming on the receiving end for Paging applications using th e Aastra W eb UI . Aastra Web UI 1 Click on Basic Settings-> Preferences->Group Paging RTP S[...]

Features i n Release 2.2 64 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 Sending End of Page Using the Configurati on Files Use the following parameters to configur e R TP streaming on the sending end for Paging applications usin g the configuration files. • softkeyN type, topsoftk eyN type, prgkeyN type, or expmodX keyN type •[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 65 5i Series IP Phone Release Notes Sending End of Page Using the Aastra W eb UI Use the following procedure to configure R TP streaming for Paging applications using the Aastra W eb UI . Aastra Web UI 1 Click on Softkeys and XML. or Click on Programmable Keys . or Click on Expansion Module[...]

Features i n Release 2.2 66 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 4 In the “ Va l u e ” field, enter a multicast IP add ress and a port number for the Paging key . When you press this key , the phone initiates an outgoing mu lticast RTP session to the specified address(es) using the specified port. (F or example, 239.0.1[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 67 5i Series IP Phone Release Notes Using the Configured Paging Key on the IP Phone The following procedure describes the us e of the Paging key . The procedures assumes you have already configured the Paging key using th e configuration files or the Aastra W eb UI. Notes: 1. Recipient of a[...]

Features i n Release 2.2 68 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 Simplified T ransfer Using BLF and Speeddial Keys In Release 2.2, a transfer (Xfer) enhanc ement has been added to the original functionality of the BLF and Speeddial keys - BLF/Xfer and Speeddial/Xfer . Prior to this release, the IP Phones supp orted BLF , Xf[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 69 5i Series IP Phone Release Notes BLF/Xfer Key Requirements and Functionality • BLF/Xfer and BLF A BLF/Xfer key can be configured for subscribing to a n extension and monitor the status of the extension, similar to the t h e BLF key functionality . Changes of the state of the monitored [...]

Features i n Release 2.2 70 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 Speeddial/Xfer Key Requirements and Functionality The Speeddial/Xfer key has the following capabilities: • Speeddial/Xfer and Speeddial When the pho ne is in the “ Idle ” state, pressing the Speeddial/Xfer key causes the phone to go o ffhook and dial the[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 71 5i Series IP Phone Release Notes Configuring the BLF/Xfer Key and the Speeddial/Xfe r Key Using the Configuration Files Y ou use the following parameters in th e configuration files to configure the BLF/Xfer key and/or Speedd ial/Xfer key on the IP Phone. Examples: softkey1 type: speeddi[...]

Features i n Release 2.2 72 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 Configuring the BLF/Xfer Key and the Speeddial/Xfe r Key Using the Aastra Web UI Y ou configure the BLF/Xfer key and/or the Speeddial/Xfer Key on the IP phone similar to configuring a BLF key or speeddial key using the Aastra W eb UI. Use the following procedu[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 73 5i Series IP Phone Release Notes T op Key s T ab (57i example ) 2 Choose a key that you want to assign the BLF/Xf er key or a Speeddial/Xfer key to, and select BLF/ Xfer or Speeddial/Xfer from the “ Ty p e ” field.. 3 In the “ Label ” field, enter a key label to assign to the BLF[...]

Features i n Release 2.2 74 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 Ability to Disable Switching Focus to a Ringin g Line When on a Call In Release 2.2, it is now possible to control the behav ior of the phone when it receives an incoming call when it is alread y in a connecte d call. By default, and in the previous release be[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 75 5i Series IP Phone Release Notes Configuring “Switch Focus to Ringing Line” Using the Aastra Web UI Use the following procedure to enable or disable the “Switch Focus to Ringing Line” using the Aastra W eb UI . Aastra Web UI 1 Click on Basic Se ttings->Preferences->General.[...]

Features i n Release 2.2 76 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 Security Features 802.1x Support The IP phones now support the IEEE 802.1x protocol. The 802.1x protocol is a standard for passing Extens ible Authentication Protocol (EAP) over a wired or wireless Local Area Network (LAN). The 802.1x protoc ol on the IP phone[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 77 5i Series IP Phone Release Notes Certificates and Private Key Info rmation • If the certificates and private key are NOT stored in the phone: — the phone conn ects to an open un authenticated VLAN and the certificates are downloaded. or — the phone connects using EAP-MD5 to a restr[...]

Features i n Release 2.2 78 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 Configuring the 802.1x Protocol Us ing the Configuration Files Use the following parameters to co nfigure the 802.1x Protocol on your phone using the configuration files. For EAP-MD5 use: • eap type •i d e n t i t y • md5 pas sword • pc port passthroug[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 79 5i Series IP Phone Release Notes Parameter – pc port passthru enabled IP phone UI Options->Administrator Menu-> Network Settings->Ethernet Link Aastra Web UI Advanced Settings->Network-> Basic Network Settings Configuration Fi les aastra.cfg, <mac>.cfg Description [...]

Features i n Release 2.2 80 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 Parameter – identity IP Phone UI: Options->Administrator Menu-> Network Settings->Ethernet Link-> 802.1x Settings->EAP-MD5 Settings Aastra Web UI: Advanced Settings->802.1 x Support->General Configuration Fi les aastra.cfg, <mac>.c[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 81 5i Series IP Phone Release Notes Parameter – 802.1x root and intermedia te certificates Aastra Web UI: Advanced Settings->802.1 x Support-> EAP-TLS Settings Configuration Fi les aastra.cfg, <mac>.cfg Description S pecifies the file name that co ntains the root and intermedi[...]

Features i n Release 2.2 82 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 Parameter – 802.1x trusted certifi cates Aastra Web UI: Advanced Settings->802.1 x Support-> EAP-TLS Settings Configuration Fi les aastra.cfg, <mac>.cfg Description S pecifies the file name that co nt ains the trusted certificates. Format St r i [...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 83 5i Series IP Phone Release Notes Configuring the 802.1x Protocol Us ing the IP Phone UI Use the following procedure to con figure the 802.1x Protocol on your p hone using the IP Phone UI. Note: If configuring 802.1x using the IP Phone UI, the certificates and private keys mu st already b[...]

Features i n Release 2.2 84 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 4 The PC PassThru Port is enabled by defaul t. Note: The PC PassThru Port must be enabled to use the 802.1x Proto col. 5 Press Done . 6S e l e c t 802.1x Se ttings. 7S e l e c t 802.1x Mo de. Aastra IP Phone UI Ste p Action Done - Enable PassT hru Port Enable [...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 85 5i Series IP Phone Release Notes 8S e l e c t EAP-MD5 to configure th e phone to use MD5 authentication; or Select EAP-TLS to configure the phone to use TLS authenticati on. Note: The 802.1x Protocol is disabled by defa ult. If y ou select EAP-TLS authent ication, you must use the config[...]

Features i n Release 2.2 86 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 12 Enter the identity or user name used for authenticating the phon e. 13 Use the softkeys as applicable while entering the username; then press Done . 14 Enter the password used for authenticating the phone. 15 Use the softkeys as applicable while entering th[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 87 5i Series IP Phone Release Notes Configuring the 802.1x Protocol Us ing the Aastra Web UI Use the following procedure to con figure the 802.1x Protocol on your p hone using the Aastra W eb UI. Aastra Web UI Click on Advanced Settings->80 2.1x Support . T o configure EAP-MD5: 17 In the[...]

Features i n Release 2.2 88 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 21 Click on Advanced Settings->Network->Ba sic Network Settings . 22 The “ PC Port PassThr u Enab le/Disable ” field is enabled by default. T o d isable this field, uncheck the box. Note: The PC Port PassThru Enable Disable field must be enabled to u[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 89 5i Series IP Phone Release Notes 5 In the “ Privat e Key ” field, enter th e filename that cont ains the private key . For example: privatekey .pem . 6 In the “ T rusted Certificates ” field, enter the filename that co n tains the trusted certificates. For example: trusted_certi [...]

Features i n Release 2.2 90 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 Improved Configuration File Encryption The IP phones have an en cryption feat ure that allows Service Providers the capability of storing encrypted files on th eir server to protect against unauthorized access and tampering of sensitive info rmation (i.e., use[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 91 5i Series IP Phone Release Notes XML Features SIP NOTIFY T riggers an XML Event In order for an XML push to bypass the NA T/firewall, in Release 2.2 the phone now supports a proprietary SIP NOTIFY event (aastra-xml) with or without XML content. If XML content is provided in the SIP NOT I[...]

Features i n Release 2.2 92 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 When the phone receives the SI P NOTIF Y , it will trigger the action uri xm l sip notify parameter , if it has been previously configur ed using the conf iguration files or the Aastra W eb UI. If the action uri xml sip notify parameter is not configured, the [...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 93 5i Series IP Phone Release Notes Configuring XML SIP NOTIFY Feature Using the Config uration Files Y ou can enable or disable the XML SI P NOTIFY feature using the following parameter in the configuration file: • sip xml notify event Parameter – sip xml notify event Aastra Web UI: Ad[...]

Features i n Release 2.2 94 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 Configuring XML SIP NOTIFY Feature Using the Aast ra Web UI Use the following procedure to enable/d isable the XML SIP NOTIFY feature in the Aastra W eb UI. Aastra Web UI Enabling/Disa bling the XML SIP NOTIFY Feature 1 Click on Advanced Settin gs->Global S[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 95 5i Series IP Phone Release Notes Configuring the Action URI for a n empty XML SIP NOTIFY using the Configuration Files If the content is missing in the SIP NOTIFY message received by the phone, the phone automatically uses the value you specify for the fo llowing parameter: • action ur[...]

Features i n Release 2.2 96 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 Configuring the Action URI for a n empty XML SIP NOTIFY using the Aastra Web UI Use the following procedure to configur e the Action URI for an empty XML SIP NOTIFY using the Aastra W eb UI. Aastra Web UI Setting an Action URI XML SIP Notify 1 If the content i[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 97 5i Series IP Phone Release Notes RTP and Multicast RTP via XML The IP Phones have new XML commands an Administrator can use with the “ AastraIPPhoneExecute ” object. These commands allow the phone to send/ recieve an R TP stream to/from gi ven multicast/unicast addresses (without inv[...]

Features i n Release 2.2 98 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 RTP R x The R TPRx URI instructs the phone to r eceive a Unicast R TP stream or stop receiving Unicast or Multicast R TP streams. The R TPRx formats to use with the AastraIPPhoneExecute ob ject in the URI are: • R TPRx:i:p:v • R TPRx:S top Where i S pecifi[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 99 5i Series IP Phone Release Notes RTPT x The R TP Tx URI instructs the phone to transmit a Unicast R TP stream or to stop transmitting Unicast or Multicast R TP strea ms. The R TP Tx formats to use with the AastraIPPh oneExecute object in th e URI are: • R TP Tx:i:p • R TP Tx:S top No[...]

Features i n Release 2.2 100 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 RTP M Rx The R TPMRx URI instructs the phone to rec e iv e a Multicast R TP stream. The R TPMRx format to use with the Aastra IPPhoneExecute object in the URI is: •R T P M R x : i : p : v Where i S pecifies the multicast IP Address fr om which to receive an[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 101 5i Series IP Phone Release Notes RTP M Tx The R TPMTx URI instructs the phone to transmit a Multicast R TP stream. The R TPMTx format to us e with the Aastra IPPhoneExecute object in the URI is: •R T P M T x : i : p Where i S pecifies the Multicast IP Address to which an RTP stream is[...]

Features i n Release 2.2 102 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 T ext Wrap for XML T extMenu Items The AastraIPPhoneT extMenu object now supports text wrappi ng on two lines for its items. This is done us ing a new attribute called " wr apList ". This attribute allows you to specify the text wrapping to an addit[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 103 5i Series IP Phone Release Notes Configuring the T ext Wr apping Parameter Y ou use the following parameter with the XML AastraIPPhoneT extMenu object: •w r a p L i s t Example <AastraIPPhoneTextMenu destroyOnExit ’”yes” wrapList =”yes”.... ..... <AastraIPPhoneTextMenu[...]

Features i n Release 2.2 104 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 Polling Action URI Another way to reach a phone behind a NA T/firewall is to have the ph one make an XML call at periodic intervals. A new Action URI was added in Release 2.2 called action uri poll which commands the phone to perform an XML call at configurab[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 105 5i Series IP Phone Release Notes Configuring Polling Action URI via the Aastra Web UI Use the following procedure to config ure polling Action URI using the Aastra We b U I . Aastra Web UI 1 Click on Advanced Settin gs->Action URI . 2 In the “ Poll ” field, enter a URI to be call[...]

Features i n Release 2.2 106 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 Deployability Features SIP Registration St atus in Aastra W eb UI The IP Phones now show the SIP registra tion status on the IP Phone’ s Network Status screen in the Aastra W eb UI. If there are accounts configured on the IP Phone, their SIP stat us displa [...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 107 5i Series IP Phone Release Notes St atus Conditi on Desription Registered Displays this status on account s that HA VE been registered with the SIP proxy server . Example : Backup Registrar Line SI P Account Status Used? 1 9057604603@an asipproxy.aas tra.com:5060 Re gistered Yes where A[...]

Features i n Release 2.2 108 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 Support for HTTP and HTTPS Configuration Se rvers on Non-St andard Port s Prior to Release 2.2, the IP Phones us ed the default port numbers for loading configuration over HTTP (Port 80), HTTPS (Port 443) and DHCP option 66. Now the IP Phones allow an Adminis[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 109 5i Series IP Phone Release Notes Configuring HTTP and HTTPS Port Using the IP Phone UI Use the following procedure to configur e the HTTP or HTTPS port using t he IP Phone UI. Parameter – https port IP Phone UI: Options->Administrator Menu-> Configuration Server->HTT PS Setti[...]

Features i n Release 2.2 110 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 4 Enter the HTTP po rt that the server uses to load the configuration to the phone over HTTP . Press Done . 5 Press Options to save your changes and exit from the Options Menu. Configuring HTTPS Port 1 Press Options->Admi nistrator Men u . 2 Enter your Adm[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 111 5i Series IP Phone Release Notes Configuring HTTP and HTTPS Port Using the Aastra W eb UI Use the following procedure to config ure the HTTP or HTTPS port using t he Aastra W eb UI. . Aastra Web UI Configuring HTTP Port 1 Click on Advanced Settin gs->Configu ration Server->Setting[...]

Features i n Release 2.2 112 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 Configuring HTTPS Port 1 Click on Advanced Settin gs->Configu ration Server->Settings . 2 In the “ Download Procotol ” field, select HTTPS . 3 In the “ HTTPS Server ” fi eld, enter the HTTPS server that dow nloads the configura tion to the phone[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 113 5i Series IP Phone Release Notes Ability to Set TFTP and FTP Path for Configuration Servers The IP Phones now allow the acqu isition of configuration files from subdirectories when connecting to either a TFTP or FTP server . An Administrator can specify a TFTP path, an alternate TFTP pa[...]

Features i n Release 2.2 114 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 Parameter – alternate tf tp path Aastra Web UI Advanced Settings -> Configuration Server ->Settings IP Phone UI Options->Administrator Menu-> Configuration Server ->TFTP Settings Configuration Fi les aastra.cfg, <mac>.cfg Description S [...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 115 5i Series IP Phone Release Notes Configuring a TFTP or FTP Pa th Using the Aastra Web UI Use the following procedure to configure a TFTP path or FTP path on the IP Phones. . Aastra Web UI Configuring TFTP an d Alternate TFTP Path 1 Click on Advanced Settin gs->Configu ration Server-&[...]

Features i n Release 2.2 116 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 Configuring FTP Path 1 Click on Advanced Settin gs->Configu ration Server->Settings . 2I n t h e “ FTP Path ” field, enter the path name for which the co nfi guration files reside on the FTP server for downloading to the IP Phone. Note: Enter the pa[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 117 5i Series IP Phone Release Notes Configuring a TFTP or FTP Pa th Using the IP Phone UI Use the following procedure to configur e a TFTP or FTP path using the IP Phone UI. Aastra IP Phone UI Ste p Action Configuring TFTP Pat h 1 Press Options->Admi nistrator Men u . 2 Enter your Admi [...]

Features i n Release 2.2 118 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 5 Press DONE to save the entry for the TFTP Path to the phone’s configuration. Configuring Alternate TFTP Path 1 Press Options->Admi nistrator Men u . 2 Enter your Admi nistrator password and press Enter . 3S e l e c t Configuration Server->TF TP Sett[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 119 5i Series IP Phone Release Notes 5 Press DONE to save the entry for the Alterna te TFTP Path to th e phone’s configuration. Configuring FTP Path 1 Press Options->Admi nistrator Men u . 2 Enter your Admi nistrator password and press Enter . 3S e l e c t Configuration Serve r ->FT[...]

Features i n Release 2.2 120 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 NA T T raversal Features Configurable SIP and TLS Source Port s A System Administrator can now confi gur e the SIP and TLS source ports on the IP Phone. Previously , the IP phone used default values ( 5060 for UDP/TCP and 5061 for TLS). The two new parameters[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 121 5i Series IP Phone Release Notes Configuring SIP and TLS Source Ports Using the Co nfiguration Files Parameter – sip local port Aastra Web UI: Advanced Settings->Global SIP-> Advanced SIP Settings Configuration Fi les aastra.cfg, <mac>.cfg Description S pecifies the local [...]

Features i n Release 2.2 122 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 Configuring SIP and TLS Source Ports Using the Aastra Web UI Use the following procedure to configure SIP and TLS source ports using t he Aastra W eb UI. . Aastra Web UI 1 Click on Advanced Settin gs->Global SI P->Advanced SIP Settings. . 2T h e “ Loc[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 123 5i Series IP Phone Release Notes RPORT Support The Session Initiation Protocol (SIP) operates over UDP and TCP . When used with UDP , responses to requests are return ed to the source address from which the request came, and returned to the port written into the to pmost “V ia” head[...]

Features i n Release 2.2 124 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 Configuring Rport Using the Configuration Fil e s Use the following parameter to configure Rp ort on your phone. •s i p r p o r t Parameter – sip rport Aastra Web UI: Advanced Settings->Network-> Advanced Network Setting s Configuration Fi les aastr[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 125 5i Series IP Phone Release Notes Configuring Rport Using the Aastra Web UI Use the following procedure to configure Rport on your phone using the Aastra We b U I . Aastra Web UI 1 Click on Advanced Settin gs->Network->Advanced Network Settings . 2 In the "Advance d Network Se[...]

Features i n Release 2.2 126 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 BroadSof t Interoperability Features CMS Support The IP phones now suppor t HTTP/HTTPS digest authentication as defined in RFC 2617. (The HTTP client supports digest authentication; the HTTP server does not; the HTTP server supports basic authentication). Thi[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 127 5i Series IP Phone Release Notes Configuring HTTP/HTTPS Digest Authenti cation Using the Configuration Files Use the following parameters to conf igure HTTP /HTTPS Digest Authentication on the phone. Parameter – http digest username Configuration Fi les aastra.cfg, <mac>.cfg Des[...]

Features i n Release 2.2 128 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 How it Works with the BroadSoft CMS Tool If you enable the HTTP/HTTPS digest auth entication feature, the phone behaves as follows with the BroadSoft CMS tool: 1. Factory default the phone. 2. Configure the HTTP or HTTPS server (specify the HTTP or HTTPS serv[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 129 5i Series IP Phone Release Notes 4. Press the “ Log In " key to displays the username/passw ord screen. 51i and 53i Login Screens 55i, 57i, and 57i CT Login Screens 5. Enter a username in the “ Username ” field (up to 40 cha racters) and a password in the “ Password ” fie[...]

Features i n Release 2.2 130 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 Server-Side Do Not Disturb (DND), Call Forward (CFWD) , and Automatic Call Distribution (ACD) Support The IP phones now support server -side DND, CFWD, and ACD feature events.This feature is called “as-fe ature-event” and works with the DND, CFWD, and ACD[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 131 5i Series IP Phone Release Notes When you press the DND, CFWD, or ACD key , only one attempt is made to enable/disable the “as-feature-event” feature on the server . The mess age “ T rying ” displays on the phone’ s LCD after pressing the key . If the attempt is successful, th[...]

Features i n Release 2.2 132 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 Note: IMPOR T ANT ! If DND and CFWD are configured to use “ Account ” mode on the IP Phone, pressing the DND an d CFWD ke ys apply to the account in focus as described in the section, “Account-Based Do Not Disturb (DND) and Call Forward (CFWD)” . If A[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 133 5i Series IP Phone Release Notes Configuring Server-Side DND, CFWD, and ACD Using the Configuration Files If the phone-side features of the DND, CFWD, and ACD keys a re enabled, the phone uses the existing parameter values fo r these keys. If the se rver-side features are enabled, the p[...]

Features i n Release 2.2 134 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 Configuring Server-Side DND, CFWD, and ACD Using the Aastra Web UI Use the following procedure to enable/dis able the server -side “ as-feature-event” on the IP Phone using the Aastra W e b UI. . Aastra Web UI 1 Click on Advanced Settin gs->LineN->A[...]

Features in Re lease 2.2 RN-001029-00, Rev 06, Release 2.2 135 5i Series IP Phone Release Notes 4 Click on Advanced Settin gs->Global SI P->Advanced SIP Settings . 5 In the “Advanced SIP Settings” section, in the “ As-Feature-Event Su bs cription Period ” field, enter the amount of time, in seconds, that the phon e waits after sending[...]

Issues Resolved on Series 5i Phone s in Release 2.2 136 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 Issues Resolved on Series 5i Phones in Release 2.2 This section describes the issues resolv ed on the Series 5i IP phones in Release 2.2. The following table provides t he issue number and a brief description of each fix. Note: Unle[...]

Issues Resolved on Se ries 5i Phones in Release 2. 2 RN-001029-00, Rev 06, Release 2.2 137 5i Series IP Phone Release Notes DEF08852 Auto-answer calls are no longer rejected when you are already in a call; they are now treated as normal calls. Th e previo us behavior affected Fonality H UD users. SIP DEF07873 Display na me portion of the F ROM and [...]

Issues Resolved on Series 5i Phone s in Release 2.2 138 RN-001029-00, Rev 06, Rele ase 2.2 IP Phone Release Notes 2.2 Robustness DEF07948 Phones no w work properly when the y fail to renew a registration, either because of network issues or b ecause of SIP message floods. DEF08186 Phones now corren tly clear down the call when making a call to a pa[...]

Contacting Aastra Telec om Support RN-001029-00, Rev 06, Release 2.2 139 5i Series IP Phone Release Notes Cont acting Aastra T elecom Support If you’ve read this release note, and consulted the T roubleshooting sectio n of your phone model’ s manual and still have prob lems, please send inqu iries via email to support@aastra.com.[...]

[...]

[...]

Generic SIP IP Phone Model 5i Series 2.2 Release Notes Copyright © 2008 Aastra T elecom. All rights reserv ed. Information in this document is subject to change without notice. Aastra T elecom assumes no re sponsibility fo r any errors that may appear in this document. Product capabilities described in this document pertain solely to Aastra T elec[...]