Acer AL1916 manual

1 English Table of Contents Preface ............................................................................................................................... 2 FCC Statemen t Warning .......................................................................................................... ..... 2 Canadian DOC Notice ..........................[...]

2 Preface This manual is designed to assist users in setting up and using the LC D Monitor. Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. The information in this document is subject to cha nge without notice. This document contains proprietary information pro[...]

3 Important Safety Instructions Please read the following instructions carefully. Th is manual should be retained for future use. 1. To clean LCD Monitor screen; -- Power off LCD Monitor and unplug the AC Cord. -- Spray a non-solvent cleaning solution onto a rag. -- Gently clean the screen with dampened rag. 2. Do not place the LCD Monitor near a w[...]

4 IT Equipment Recycling Information IT Equipment Recycling I nformation: Acer is strongly committed to environmental protecti on and views recycling, in the form of salvaging and disposal, of used equipment as one of the company’s top priorities in minimizing the burden placed on the environment. We at Acer are very conscious of the environmenta[...]

5 Chapter 1 Installation Unpacking Before unpacking the LCD Monitor, prepare a suita ble workspace for your Monitor and computer. You need a stable and clean surface near a wall power outlet. Make sure that LCD Monitor has enough space around it for sufficient airflow. Though the LCD Monitor uses very little power, some ventilation is needed to ens[...]

Detaching LCD Monitor from Its Stand Unscrew screws the swivel base support column and pull down the hinge to release. Figure 1-3 Interface for Arm Applications Before installing to mounting device, please refer to Fig.1-3. The rear of this LCD display has four integrated 4 mm, 0.7 pitches threaded nuts, as well as four 5 mm acces s holes in the pl[...]

7 Chapter 2 Display Controls General Instructions Press the power button to turn the monitor on or o ff. The other control buttons are located at front panel of the monitor (See Figure 2-1). By changing th ese settings, the picture can be adjusted to your personal preferences.  The power cord should be connected.  Connect the video cable from[...]

8 Front Panel Control / Power Button: Press this button to turn the monitor ON or OFF, And display the monitor’s state. Power Indicator: Green — Power On mode. Orange — off mode Menu / Enter : Activate OSD menu when OSD is OFF or activate/de-activate adjustment function when OS D is ON < : Navigate through adjustment icons when OSD is ON o[...]

9 How to Adjust a Setting 1. Press the MENU-button to activate the OSD window. 2. Press < or > to select the desired function. 3. Press the MENU-button to select the function that you want to adjust. 4. Press < or > to change the settings of the current function. 5. To exit and save, select the exit function. If you wa nt to adjust any [...]

10 N/A English N/A Deutsch N/A Français N/A Español N/A Italiano N/A 繁體中文 or Русский N/A 简体中文 or Hollands N/A 日本語 or Suomalainen Multi-language selection. H. Position Adjust the horizontal position of the OSD. V. Position Adjust the vertical position of the OSD. OSD Timeout Adjust the OSD timeout. N/A Auto Config Auto[...]

11 Chapter 3 Technical Information Specifications LCD Panel Size 19" Display Type Active matrix color TFT LCD Resolution 1440 x 900 Display Dot 1440 x (RGB) x 900 Display Area (mm)(H x V) 408 x 255 Display Color 16.2M with FRC or Dithering Brightness 300 cd/m 2 (typical) Contrast Ratio 700:1 (typical) Response Time 5ms (typical) Lamp Voltage 6[...]

12 Power Management Mode Power Consumption* AC Input LED Color On 55W maximum 240 VAC Green Off 2W maximum 240 VAC Amber Soft switch off 1W maximum 240 VAC Dark * Meeting VESA DPMS requirements measured from AC Input end of AC power cord. Sync Input Signal Separate TTL compatible horizontal and vertical synchronization Polarity Positive and negativ[...]

13 Pin Assignment Signal PIN Description PIN Description PIN Description 1 2 3 4 5 Red Green Blue Digital GND Digital GND 6 7 8 9 10 Red Rtn Green Rtn Blue Rtn +5V Hot Plug Detect 11 12 13 14 15 NC SDA H. Sync. V. Sync. SCL 1 5 6 10 11 15 Digital Video Input Connector : DVI – D (option) Pin – Assignment of DVI –D connector : 1 TX2- 9 TX1- 17 [...]

14 Standard Timing Table If the selected timing is NOT included in table below, this LCD monitor will use the m ost suitable available timing. TIMING FH(KHZ ) FV(HZ) SYNC POLARITY TOTAL (DOT/ LINE) ACTIVE (DOT/ LINE) SYNC WIDTH (DOT/LINE) FRONT PORCH (DOT/LINE) BACK PORCH (DOT/LINE) PIXEL FOREQ (MHZ) 640x350 31.469 + 800 640 96 16 48 25.175 VGA-350[...]

15 TIMING FH(KHZ ) FV(HZ) SYNC POLARITY TOTAL (DOT/ LINE) ACTIVE (DOT/ LINE) SYNC WIDTH (DOT/LINE) FRONT PORCH (DOT/LINE) BACK PORCH (DOT/LINE) PIXEL FOREQ (MHZ) 800x600 46.875 + 1056 800 80 16 160 49.5 VESA-600-75Hz 75 + 625 600 3 1 21 1024x768 48.363 – 1344 1024 136 24 160 65 XGA 60.004 – 806 768 6 3 29 1024x768 53.964 + 1328 1024 176 16 112 [...]

16 Troubleshooting This LCD Monitor has pre-adjusted using factory standard VGA timings. Due to the output timing differences among various VGA cards in the market , users may initially experience an unstable or unclear display whenever a new displa y mode or new VGA card is selected. Attention This LCD Monitor Supports Multiple VGA Modes. Refer to[...]