Alliance Laundry Systems Dishwasher manual

Para bajar una copia de estas instrucci ones en español, visite www.comlaundry.com. Keep these instructions for future reference. (If this machine changes ownership, this manual must accompany machine.) www.comlaundry.com Inst allation Instructions for S t acked W ashers and Dryers Dimensions ..................... ....................... .........[...]

© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 2 802715 IMPOR T ANT : Purchaser must consu lt the local gas supplie r for suggested instructions to be followed if the unit user smells gas. The gas utility instructions pl us the SAFE TY and W ARNING note directly above must be posted in a pr ominent location near the unit f[...]

© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 802715 3 Dimensions SWD897N * With leveli ng legs turned into base. NOTE: Exhaust op enings are 4 inch (10.2 c m) metal ducting. SWD898N *With leveling legs turned into base. NOTE: Exhaust op enings are 4 inch (10.2 c m) metal ducting. 1 3/8 in. NPT Gas Connection 23.5 in. (59[...]

© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 4 802715 Before Y ou St art Supplies For most installations, the basic supplies you will need are: Figure 1 NOTE: If the unit is deliver ed on a cold day (below freezing), or is stor ed in an unheated r oom or area during the cold months, do not attempt to operate it until the[...]

© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 802715 5 Inst allation Step 1: Position Unit Near Inst allation Area Move unit as close to the desired area of installation as possible. NOTE: For best performance and to minimize vibration or movement, install washer on a solid, sturdy and level floor . Some floors may need t[...]

© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 6 802715 NOTE: Use of the dispenser drawer or unit doors as a handle in the transportation of the unit may cause damage to the dispenser or doors. Place unit in position on a soli d, sturdy and level floor . Installing the unit on any type of carpeting, soft tile, a platform o[...]

© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 802715 7 Step 3: Connect Fill Hoses Wat e r Su p p l y W ater supply faucets must fit standard 3/4 inch (19.1 mm) female garden hose couplings. DO NOT USE SLIP-ON OR CLAMP-ON CONNECTIONS. W ater supply faucets should be readily accessible to permit turning them off wh en washe[...]

© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 8 802715 IMPOR T ANT : Hoses and other natural rubber parts deteriorate after extended use. Hoses may develop cracks, blisters or material wear from the temperatur e and constant high pressur e they are subject to. All hoses should be ch ecked on a monthly basis for any visibl[...]

© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 802715 9 Step 4: Connect Drain Hose to Drain Recept acle Remove the drain hose from its shipping position on the rear of the washer by unhooking the hose f rom the retainer clamp and by removing th e shipping tape. Install the drain hose into the drain receptacle (standpipe, w[...]

© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 10 802715 Step 5: (Gas Dryer Only) Connect Gas Supply Pipe 1. Make certain your dryer is equipped for use with the type of gas in your laundry room. Dryer is equipped at the factory for Natural Gas with a 3/8 inch NPT gas connectio n. NOTE: The gas service to a gas dryer must [...]

© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 802715 11 4. T ighten all connections securely . T urn on gas and check all pipe connections (internal & external) for gas leaks with a non-corrosive leak detection fluid. NOTE: The dryer and its appliance main gas valve must be disconnected from the gas supp ly piping sys[...]

© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 12 802715 Grounding Information • This dryer must be con nected to a grounded metal, permanent wiring system; or an equipment-grounding cond uctor must be run with the circuit conducto rs and connected to the equipment-grounding term inal or lead on the dryer . • For model[...]

© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 802715 13 Connecting Power Cord with Three-Wire Plug NOTE: Four -wire cord is requir ed for mobile homes or where codes do not permit grounding through neutral. Figure 12 1. Disconnect power to dryer . 2. Remove access cover from rear of dryer . Figure 13 3. Use a strain relie[...]

© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 14 802715 4. Use the three screws from the accessories bag to attach the power cord wir es to the terminal block. Refer to Figur e 15 . Figure 15 5. T ighten all screws firmly . IMPOR T ANT : Failure to tighten these scr ews firmly may result in wir e failure at the terminal b[...]

© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 802715 15 3. Remove ground screw and save for use in S tep 5. Remove wire and use in Step 6. Figure 18 4. Use a strain relief and insert end of power cord through power suppl y hole. Figure 19 5. Attach power cord ground (green) wire to rear bulkhead using g round screw remove[...]

© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 16 802715 Step 7: Connect Dryer Exhaust System • DO NOT use plastic or thin foil ducting. Rigid metal duct is recommended. Refer to Figur e 21 . • Locate dryer so exhaust duct is as short as possible. • Be certain old ducts are cleaned before installing your new dryer . [...]

© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 802715 17 Exhaust Direction The dryer can be exhausted to the ou tdoors through the back, left, right or bottom of the dryer . EXCEPT ION: Gas dryers cannot be vented out the left side because of the burner housing. Dryer is shipped from factory ready for rear exhaust. Exhaust[...]

© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 18 802715 Step 8: (W asher On ly) Remove th e Shock Sleeves and Shipping Brace Remove front access panel by removing the two screws at the bottom of the panel. Remove the five bolts an d lockwashers from shipping brace with 9/16 inch wrench and remove brace. Refer to Figur e 2[...]

© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 802715 19 Step 10: Plug In the W asher and Dryer Electric Dryer Connect the dryer to an electrical pow er source. Refer to Step 4 for information on connecting po wer cord. Figure 25 Gas Dryer Dryer requires 120 V olt, 60 He rtz electrical supply and comes equipped with a 3-pr[...]

© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 20 802715 Washer - All Models Except L TSA7A*N2989 W asher requires 120 V olt, 60 Hertz e lectrical supply and comes equipped with a 3-prong grou nding plug. Refer to serial plate for specific electrical requirements. NOTE: The wiring diagram is located behind the control pane[...]

© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 802715 21 When plugging in the washer: • DO NOT overload circuits. • DO NOT use an extension cord. • DO NOT use an adapter . • DO NOT operate both a washer and gas dryer on the same circuit. Use separately fused 15 Amp circuits. The washer is des igned to be operated o[...]

© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT 22 802715 After the dryer has operated fo r approximately five minutes, observe burn er flame through lower front panel. Adjust the air shutte r to obtain a soft, uniform blue flame. (A lazy , yellow-tipped flame indicates lack of air . A harsh, roaring, very blue flame indica[...]

[...]

© Copyright, Alliance Laundry System s LLC – D O NOT COPY or TRANSMIT Inst aller Checklist Fast T rack for Inst alling the Unit (Refer to the manual for mor e detailed information) • Position Unit Near Installation Are a. 1 CHECK • Position and Level the Unit. 2 CHECK SWD833N SWD833N • Connect Fill Hoses. TLW1976N HOT COLD 3 Filter Screens[...]