Audiovox AS9233ST manual

128-8605 1 of 20 1 SELECT ABLE FEA TURES The selectable features can be set manually as explained below , or with the RF feature programmer . T o set features using the RF programmer , follow the instructions packaged with the programmer . Factory default settings are indicated by bold text. Note : The method of manual override can either be select[...]

128-8605 2 of 20 2 Note: Where indicated, press transmitter lock button to change, the Factory Transmitter Lock button, Door Lock Switch, or the supplied transmitter can be used. T o program these selectable features; Action System Response Turn ignition on No response Press and release the valet switch 3 times 1 Chirp - LED 1 flash Within 3 second[...]

128-8605 3 of 20 3 T o exit program mode, turn ignition off, or press and release valet switch. RF Programmable Features Bank 3 Is Remote Start Selectable Features: Feature Selection 1 Chirp 2 Chirps 3 Chirps 4 Chirps 5 Chirps 6 Chirps 1st Defrost Output NA 2nd RF S tart Chirp O f f On On & Carfinder 3rd Run Time 5 Mins 10 Mins 15 Mins 20 Mins [...]

128-8605 4 of 20 4 Action System Response Turn ignition on No response Press and release the valet switch 3 times 1 Chirp - LED 1 flash Within 3 seconds, turn ignition Off, On, Off, On Short chirp, then 2 long chirps This Action Accesses Feature Bank 3 Remote S tart Selectable Features First Press the valet switch one time Non Functional On This Un[...]

128-8605 5 of 20 5 This Remote S tart/Alarm System is designed to be used with Automatic T ransmission V ehicles Only! The unit provides a selectable ignition control that allows a number of selectable timed outputs for glow plug pre-heat which may be required for certain diesel vehicles, (see selectable feature #9). If the diesel engine has a inst[...]

128-8605 6 of 20 6 from all areas of the vehicle. The selected location must be within 18" of the control module to allow routing and connecting of the 4 pin harness. Secure the shock sensor to the chosen location using two #8 self taping sheet metal screws. The sensor can also be secured to an existing dash brace using cable tie straps. Which[...]

128-8605 7 of 20 7 Note: This wire must be connected to the vehicle side of the starter cut relay (when used). For the electrical neutral switch configuration, this connection must be made between the starter inhibit relay , (when used) and the neutral safety switch as shown in the following diagram. Failure to connect this wire to the ignition swi[...]

128-8605 8 of 20 8 Purple Wire: (+) Door Trigger Input If the vehicle's door courtesy light switches + 12 volts when the door is opened, (Some Fords and some Imports), you must connect this wire to the positive output from one of the vehicle's door pin switches. In most cases, the Purple wire will need to be connected to only one door swi[...]

128-8605 9 of 20 9 Dark Green Wire: (-) Instant Trigger Input This is the instant on ground trigger input wire. This wire must be connected to the hood and trunk pin switches where installed. Note: This wire will be shunted when remote control channel 3 is accessed, (trunk release). This wire will remain shunted all the while there is ground presen[...]

128-8605 10 of 20 10 Black White/Black Grey Wire: Negative Inhibit Input The Grey w/ Black T race wire provides an instant shut down for the Remote S tart Control Module whenever it is grounded. Connect the Grey trace wire to the hood pin switch previously installed. This wire must be routed through a grommet in the firewall and connected to the ho[...]

128-8605 11 of 20 11 Black Wire: Chassis Ground Source Connect the Black wire to a known vehicle ground source or to a solid clean metal part of the chassis. Be certain to remove any paint or grease and secure this wire with a self taping screw and ring terminal. Chassis Ground Connection Detail Brown w/ Black T race Wire: Positive Inhibit Input Th[...]

128-8605 12 of 20 12 Green/Y ellow Wire: Diesel W ait T o S tart Input The Green/Yellow wire will connect to a diesel vehicles glow plug wire. When the unit receives a start command, this wire must go to + 12 then to ground to allow the crank sequence to begin. When ignition #1 is activated by the remote start unit, the glow plug circuit gets energ[...]

128-8605 13 of 20 13 Note! When installing this system as a stand alone passive security system, the RED wire in this connector must be connected to a rest at ground , + 12 VDC switched ignition source. RED w/BLACK, GREEN & GREEN/BLACK wires must be connected to ground. The BLUE wire in this connector will not be required for the stand alone in[...]

128-8605 14 of 20 14 output would be to disarm a factory theft deterrent system to prevent false triggering of the factory alarm when the remote start unit engages or when the 785 is used to unlock the doors. Black w/ Light Green T race Wire: Pulsed Ground Output After S tart The Black w/ Light Green Trace wire will provide a 1 second mA pulsed gro[...]

128-8605 15 of 20 15 3 Wire Positive Switched Door Locks: In this application, the Red wire of the door lock harness provides a + 12 volt pulse during the disarming sequence, or pulsed 12 volt unlock output. Connect the Red wire to the low current 12 volt signal wire from the factory door unlock switch to the factory door unlock relay . The Green w[...]

128-8605 16 of 20 16 T o Learn T ach 1. Turn the ignition key to the On position. 2. Press and release the valet/program push button switch 3 times. 3. Immediately turn the ignition key Off. 4. Press and hold the valet/program push button switch, then start the vehicle using the key . 5. When the unit senses the tach signal, the parking lights will[...]

128-8605 17 of 20 17 TESTING YOUR INST ALLA TION: CAUTION!! The following procedure must be performed af ter the installation of an Audiovox Remote S tart Device. It is the responsibility of the installing technician to complete these tests. Failure to test the unit in the following manner may result in personal injury , property damage, or both. H[...]

128-8605 18 of 20 18 MECHANICAL NEUTRAL SAFETY SWITCH CONSIDERA TIONS: Mechanical neutral safety switch configurations differ slightly in that they do not offer the same level of safety when installing a remote start device. Often when the ignition switch is turned off while the gear selector is in any position other than park or neutral, the mecha[...]

128-8605 19 of 20 19 METHOD 2 T o connect to the key in sensor circuit as shown for method 2: A. Locate the control wire that connects the drivers door pin switch to the key in sensor switch. B. Cut this wire and connect the ignition cylinder side to chassis ground. C. Locate the key in sensor switch wire that connects the chime module to the ignit[...]

128-8605 20 of 20 20 © 2009 Audiovox Electronics Corp., Hauppauge, N.Y. 11788 12 8 -8 6 05[...]