Beckett CF 2300A manual

23 0 0 MODEL MODEL MODEL MODEL MODEL CF 2300A Instruction M anual Oil Burner Thank you for purchasing a Beckett burner . With proper care and regular maintenance, it will provide years of trouble-free service. Please take a few minutes to read the section entitled “T o the owner” inside this manual. Then, keep the manual in a safe place where i[...]

Instruction Manual – Model CF2300A Oil Burner 2 Form 6104 BCF-23-R0399 Please . . . r ead this page first Denotes presence of a hazard which, if ignored, could result in minor personal injury or property damage. Hazard definitions The following will be used throughout this manual to bring attention to hazards and their risk factors, or to special[...]

Instruction Manual – Model CF2300A Oil Burner 3 Form 6104 BCF-23-R0399 W arranty Beckett warrants its equipment to those who have purchased it for resale, including your dealer . If you hav e any problems with your equipment or its installation, you should contact your dealer for assistance. Refer to warranty sheet in literature packet included w[...]

Instruction Manual – Model CF2300A Oil Burner 4 Form 6104 BCF-23-R0399 Pr e-installation checklist T able 1 – Nozzle capacities at various pressures ❏ Combustion air supply • The burner requires combustion air and ventilation air for reliable operation. Assure that the building and/or com- bustion air openings comply with National Fire Prot[...]

Instruction Manual – Model CF2300A Oil Burner 5 Form 6104 BCF-23-R0399 T able 2 – Air tube capacity vs. firebox pressure Figure 2 – Air tube mounting dimensions 2304 E D G T 2° 1 F E Insertion depth G Air tube to inside of chamber – 0.25" ± 0.125" T Air tube length D Tube diameter Figure 1 – Min. combustion chamber dimensions [...]

Instruction Manual – Model CF2300A Oil Burner 6 Form 6104 BCF-23-R0399 Mount the bur ner ❏ Mount flange(s) on air tube • This section does not apply to burners with welded flanges. • Do not install air tube on burner . • For non-pressure firing flange , refer to Figure 3 : Install gasket (item a ) and flange (item d ). Ignore the next par[...]

Instruction Manual – Model CF2300A Oil Burner 7 Form 6104 BCF-23-R0399 Figure 5 – Nozzle line assembly in burner ❏ ❏ ❏ ❏ ❏ Set dimension Z • Replace the rear access door on the bu rner , making sure that the adjust- ing plate assembly is now securely held in place. • Loosen acorn nut d in Figure 5 . Slide the nozzle line and plate[...]

Instruction Manual – Model CF2300A Oil Burner 8 Form 6104 BCF-23-R0399 Connect fuel line(s) ❏ Fuel unit by-pass plug • The CF2300A burner is shipped with a by-pass plug in- stalled in the fuel unit. For low/high operation, the by- pass plug must be left in the fuel unit , regardless of the fuel system used (one-pipe with by-pass loop or two- [...]

Instruction Manual – Model CF2300A Oil Burner 9 Form 6104 BCF-23-R0399 Figure 9a – T wo-pipe oil flow , low fire, “ H ” pump • Use continuous lengths of heavy-wall copper tubing, routed under the floor where possible. Do not attach fuel lines to the appliance or to floor joists if possible. This reduces vibration and noise transmission pr[...]

Instruction Manual – Model CF2300A Oil Burner 10 Form 6104 BCF-23-R0399 Legend FD Fused disconnect, by others LM Limit controls, by others OP Operating controls, by others PR Oil primary control, R8184 typical CC Flame sensor, cad cell typical TM Optional delay timer TR Ignition transformer M1 Burner motor S1 Primary oil valve S2 By-pass oil valv[...]

Instruction Manual – Model CF2300A Oil Burner 11 Form 6104 BCF-23-R0399 Sequence of operation — typical NO TE: The following sequence is based on using a type B fuel unit, with pump-mounted by-pass valve. The by-pass valve operation is reversed for a type H fuel unit. That is, the by- pass valve is powered at low fire instead of being powered a[...]

Instruction Manual – Model CF2300A Oil Burner 12 Form 6104 BCF-23-R0399 Pr epar e the bur ner for star t-up - continued ❏ Z dimension • Should be set per these instructions (see page 7). The top acorn nut ( Figure 11 , item d ) should never be loosened once the Z dimension is initially set. ❏ Adjusting plate assembly (Figure 11) • Make su[...]

Instruction Manual – Model CF2300A Oil Burner 13 Form 6104 BCF-23-R0399 T able 5 – Initial air adjusting plate settings (damper position) CLOSE OPEN 2309-1 a b d e f g Figure 12 – Air damper and damper motor assembly CLOSE 12 0 1 2 3 4 5 6 7 8 9 10 11 2309-2 a h b d c k m Legend (Figure 12) a Damper motor – do not adjust internal cam b Arm [...]

Instruction Manual – Model CF2300A Oil Burner 14 Form 6104 BCF-23-R0399 Star t the bur ner Do not proceed unless all prior steps in this manual have been completed. Failure to comply could result in se v ere personal injury , death or substantial property damage. Do not attempt to start the burner when excess oil has accumulated, when the applian[...]

Instruction Manual – Model CF2300A Oil Burner 15 Form 6104 BCF-23-R0399 Maintenance and ser vice Annual service — by qualified service technician Have the burner inspected, tested and started at least annually by a qualified service technician. This annual test/inspection should include at least the following: ❏ Replace oil nozzle. ❏ Clean [...]

Instruction Manual – Model CF2300A Oil Burner Form 6104 BCF-23-R0399 U.S.A.: P . O. Box 1289 • Elyria, Ohio 44036 • 800-645-2876 • 440-327-1060 • F AX 440-327-1064 Canada: R. W . Beckett Canada, Ltd. • 430 Lair d Road • Guelph, Ontario, N1G 3X7 • 800-665-6972 • F AX 519-763-5656 SUNTEC 1 2 3 4 5 12 13 14 6 79 10 8 15 27 H B fuel u[...]