Bosch Appliances d9412gv3 manual

EN Program Entry Guide Control Panels D9412GV3/D7412GV3 v8.11 and Higher[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | EN | 2 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 System Requirements Minimum system requirements for Classification in accordance with ANSI/SIA CP-01-2007: UL Listed and Classified co ntrol unit Model D9412GV3 or D7412GV3 UL Listed and Classified keyp ad Model D1256, D1257, D1260, D1255, D[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | EN | 3 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Table of Contents 1.0 Introduction ................................................. 5 1.1 Using t his Program Entr y Guid e ................... 5 1.2 Guid e to Programmi ng Options .................... 6 1.2.1 Local Keyp ad Progr amming ...[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | EN | 4 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 6.1 Door Prof ile .............................................. 140 6.2 Str ike Profile............................................. 143 6.3 Event Profile............................................. 145 7.0 SIA CP-01 Quick Reference ......[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 1.0 Introduction EN | 5 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 1 .0 Int roduct ion 1.1 Using this Program Entry Guide This guide is only for programming the D9412G V3 and D 7412G V3 Co ntrol Panel s. Although this guide specifically refers to the D9412GV3 Control Panels, it can be used [...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 1.0 Introduction EN | 6 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 1.2 Guide to Programming Option s Full configuration of the control panel is only achieved through use of the Remote Programmi ng Software (RPS). A limited keyp ad programmer’s mode is avail abl e to modify some of the mor[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 1.0 Introduction EN | 7 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 1.2. 1 Local Keypad Programming GV3 now offers a Local Keyp ad Programming menu with the Service Passcode o nly. It includes all custom options. For a list of program items you ca n set using Keypad Programming, refer to Fig[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 1.0 Introduction EN | 8 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Figure 2: D1260 Keypad Programming Menu and Page Ref erences Refer to Phone # on page 12. Refer to Phone # Format on page 13. Refer to Enhanced Comm on pages 130 to 132. Refer to R# Primary Device on page 18 and R# Backup De[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 1.0 Introduction EN | 9 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 1.3 Guide to U L 864 Progr amming Requirements This section identifies the pr ogramming requirements you must make in order to comply with UL 864 Commercial Fire applications. NOTICE TO USERS, INSTALLERS, AUTHORITIES HAVING [...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 1.0 Introduction EN | 10 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Table 3: UL 864 Prog ramming Requirements (continued) Product Feature/Option Permi tted in UL 864? ( Y/N) Possible Settings Settings Permitted in UL 864 Refer to Page: Bat Fail/Restoral Report Yes Yes / No Set to Yes 30 Are[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 1.0 Introduction EN | 11 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Table 3: UL 864 Prog ramming Requirements (continued) Product Feature/Option Permi tted in UL 864? ( Y/N) Possible Settings Settings P ermitted in UL 864 Refer to Page: For IP Communications to a D6600 Receiver Enhanced Com[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 12 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 2.0 Panel and Area Wide Parameters This section has twelve programming categories:  Phone  Phone Parameters  Routing  Area Parameters  Power Supervision  Printer Parameters  RPS Parame[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 13 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 If you program the primary phone number with a sequence to temporarily disable Call Waiting (typically *70 pause, but verify with the phone service provider) followed by the phone nu mber, you should progr[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 14 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 2.2 Phone Parameters The program items in this category d escribe panel- wide characteristics for telephone dialing, receiver format, an d supervisio n. Phone # Format Default: Modem IIIa 2 Selection: Mode[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 15 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Table 5: Modem IIIa 2 Communication Format Data - User ID Numbers Point/User Flag NO Point/User Flag YES 000 000 001 to 005 001 to 005 006 to 013 601 to 608 014 to 021 701 to 708 022 to 029 801 to 808 030 [...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 16 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Phone Supv Time Default: 0 Selection: 0, 10 to 240 0 No phon e line su pervision. 10 to 240 En ter the number of seconds (in 10 sec increm ents) you wis h to wait before indicating trouble. After a faulted[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 17 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Expand Test Report Default: No Selection: Yes or No Yes Off-normal events listed in Routing Group Test Reports are reported to the central stat ion. No Off-normal conditions for the events listed in the Ro[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 18 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 2.3.3 Programming Primary an d Backup Destinations Each route number has an R# Primary Device an d an R# Backup Dev ice . For e xample, if t wo phon e numbers are programmed , the R# Primary Device destina[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 19 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 There are four Route Groups which contain a selection of event categorizes and individual events. Each group has a primary a nd a backup device. The primary device is the firs t (most importan t) destinati[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 20 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 R# Backup Device Default: No Device Selection: No Device, Phone 1..4, SDI ## Path 1..4 Phone 1 Phone 1 is this group’s backup destination if the primary destination fails. Phone 2 Phone 2 is this group?[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 21 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 2.3.9 Route Group Categories Fire Reports To meet U L 864 require ments for Central Station an d Remote Station applications, enable Fire Reports . Selecting Yes enables a report to be sent wh en the event[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 22 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 User Reports Selecting Yes enables a report to be sent wh en the event occurs. Table 11: User Reports Report Selections Report Description R# Point Bypass Yes , No Point Bypass Event R# Forced Point Yes , [...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 23 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Table 12: Test Reports Report Selections Report Description R# S: Alarm 1 Yes , No Status Alarm R# S: Trouble 1 Yes , No Status Trouble R# S: Supervised 2 Yes , No Status Supervised R# Status Report Yes , [...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 24 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Table 13: Diagnostic Reports Report Selections Report Description R# SDI Dev Fail 1 Yes , No SDI device failure R# SDI Dev Restl Yes , No Restoral of SDI device failure R# Watchdog Rset Yes , No Watch dog [...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 25 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 When activating an on-board relay using remote automation software, the D9412GV3 and D7412GV3 Control Panels log and print the resulting event as: Relay 250 (Relay A) Relay 251 (Relay B) Relay 252 (Relay C[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 26 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Point Reports Selecting Yes enables a report to be sent wh en the event occurs. Table 17: Point Reports Report Selections Report Description R# Service Start Yes , No Reorts Service Walk Test Start Event R[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 27 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Access Reports Selecting Yes enables a report to be sent wh en the event occurs. Access Granted, No En try, Request to Enter (RTE) and Request to Exit (REX) Events can be ena bled or disable d by each D921[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 28 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Table 20: Eve nt Descriptions, Prioritie s, and Numbers (Continued) Event Descri ption Event Priority Event Number Forced Close Perimeter Insta nt 007 084 Forced Close Pe rimeter Dela y 007 085 Perime ter [...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 29 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 2.4 Power Supervisio n AC Fail Time Default: 1:00 Selection: 0:01 to 90:00 Program the amount of time that AC power must be off before the con trol pa nel respon ds to the AC failure. The response to re st[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 30 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 AC Tag Along is required for NFPA and UL 864 Commercial Fire sys tems. Be sure to program AC Fail/ Restoral Report as No if AC Tag Along is programmed Yes . AC/Battery Buzz Default: No Selection: Yes or No[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 31 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 P## Scope Default: No Printer Selection: No Printer, Area, Account, Panel Wide, Custom Panel Wide Printer prints all design ated events that occur panel-wide. A panel-wide printer can cross account boundar[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 32 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 P## Point Event Default: R efer to the program record sheet Selection: Yes or No P## Usr Chng Evt Default: R efer to the program record sheet Selection: Yes or No 2.6 RPS Paramete rs Use these program item[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 33 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Keypad Programming of RPS Passcode D1255 1. Refer to Figure 1 on page 7 to access Keyp ad Programming and navigate to the RPS PASSC ODE option. T he keypad shows the currently configured passcode. 2. Press[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 34 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 RPS Call Back Default: No Selection: Yes or No Yes When the control panel hears the correct RPS passcode, it hangs up the phone, seizes the phone line, then dials the program med RPS phone number (refer to[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 35 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 RPS P hone # Default: Blank Selection: Blank or up to 24 characters Blank Control panel does not dial a p hone number for RPS. 1 to 24 characters Enter up to 24 charac ters to define dialing characteristic[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 36 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 2.7 Miscellaneous Duress Type Default: 0 Selection: 0, 1, 2, or 3 0 Do n ot send a duress e vent wi th any passcode . 1 Increase the last digit by 1 to generate an alarm. For example, if the passcode is 61[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 37 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Area 1 must be enabled:  System events such as power an d phone s upervision do not sen d a report correctly if A rea 1 is disabled.  When prog rammed No , points assigned to this area do not generat[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 38 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Refer to the prompts P## Force Arm Returnab le and P## Bypass Returnable in Section 3.2 Point Responses on page 91 for returning a point to th e system when the point returns to normal or when the area is [...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 39 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 When the detector senses smoke or fire, the area’s sensor reset r elay inte rrupts power to po ints connected to it for th e time in Verify Time. When power restores to the points, the 60-sec confirmatio[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 40 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 A# Area Type Default: Regular Selection: Regular, Master, Associate, or S hared Regular Arm s or disarms as an in depen dent area. Master Does not allow arming for this area unless all asso ciate areas wit[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 41 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 2.8.2 Shared-Area Characteristics Arming a Shared Area A shared area arms automatic ally when all associate areas are armed. As soon as the last associate area is armed, the shared area automatically begin[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 42 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 A# Fire Time Default: 6 min Selection: 1 min to 90 min Enter the number of minutes the bell rings for Fire Alarm points. The relay ac tivated for this time is programmed in A# Fire Bell in Area Relays. The[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 43 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 A# Single Ring Default: No Selection: Yes or No Yes One bell output per a rming pe riod. After one alarm, alarms on any No n- fire points in the same area cannot restart the bell until the armed state chan[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 44 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 To suppress r eports:  Use Opening/Closi ng Windows to suppress reports for a specified period of time and then automatically turn them on again.  Use the Restricted O/C options. A Clo sing Report is[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 45 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 A# Area O/C Default: Yes Selection: Yes or No Yes Include the Area # and generate Opening and Closing Reports for this area when it is armed. No Do not include the Area # or generate Opening and Clos ing R[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 46 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 A# Fail to Close Default: No Selection: Yes or No Yes Fail to Close Report is sent for this area if the area is not armed when the Closing Window stop time occurs. Note: Program an exit delay tim e in Exit[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 47 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 A# Perimeter O/C Default: No Selection: Yes or No Yes This area can send Perime ter Opening and Closing Report s. No This area cannot send Perimeter Op ening and Clo sing Re ports. This item determ ines if[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 48 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Parameter Setup Requirement: Two Man Ru le can be completed on ly by en tering two valid unique passcodes with L## Passcod e Disarm authority. To avoid unintended results for the end user of the system: ?[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 49 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Parameter Setup Requirement: The Early Ambush tim er can be s tarted an d stopped only by passcodes with the L## Passcode Disarm authority. To avoid unintended results for the end user of the system:  W[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 50 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 A# Entry Warning Default: Yes Selection: Yes or No Yes Pulse the alarm output for the last 10 sec of the Ent ry Delay time. No Do not pulse the Alarm Bell output during the Entry Delay time. When en abled,[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 51 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 CC# Supervised Default: R efer to the program record sheet Selection: Yes or No Yes Only one keypad can be installed for this CC SDI address. No More than one keypad ca n be installed using this CC SDI add[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 52 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 CC# Scope Default: Refer to the program record sheet Selection: Panel Wide , Custom, No Keyp ad, Area, and Account Panel Wide A panel-wide keypad ca n view inform ation and pe rform A rming an d Disarming [...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 53 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 CC# Enter Key Relay Default: 0 Selection: 0 to 128, A, B, C (0 to 64, A, B, C for the D7412GV3) 0 The [ENTER] key is not used to activate a relay. 1 to 128 (64), A, B, C Assign the relay number that activa[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 54 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2  If a door is not programmed for this prompt and a door is not assig ned to the area using the D# Entry Area in the Access Control section, 9210 NOT READY appears at this keypad when you attempt to add [...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 55 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 For SIA CP-01 Compliance CC# Exit Tone can be set to Yes or No . CC# Arm No w Warning Default: No Selection: Yes or No Yes This keypad activates a tone and displays PLEASE CLOSE NOW. No This keypad does no[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 56 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 CC# Scroll Lock Default: No Selection: Yes or No Yes Prevents the idle syst em status t ext from scrolling automatically. Requires us er interven tion to advance. No Allows the idle syste m status text to [...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 57 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Area# Is On Default: Refer to the program record sh eet Selection: Sixteen alphanumeric characters Enter the text for this area that appears when the area is master armed or mast er instan t armed and othe[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 58 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Custom Function Default: 128 Selection: 128 to 143 Enter the Custom Function number you want to program. You can program up to sixteen Custom Functions, which are numbered 128 to 143. CF### Text Default: R[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 59 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2  128 to 143 Enable Custom Function 128 through 143 (Menu Function only): This function determine s if a passc ode is neede d to access a Custom Functio n from the menu list. ENTER PASSCODE (or Enter Pas[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 60 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 2.10.1 Commands Similar to command initiation used in other Bosch Security Systems, Inc. produc ts, the Commands method pr ovides continuity in the armi ng commands across pro duct lines an d makes an easy[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 61 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Instant arms all perimeter po ints with point res ponse that starts an instant alarm (refer to P## Pt Response in Section 3.2 Point Responses o n page 91) in the area where the keypad is assig ned. Entry a[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 62 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 View Memory Default: E Selection: -, E, or P Function No. Function Name Alternate Keystroke 9 View Event Memory [COMMAND][4][0] Use this function to view prior alarm, trouble, an d supervisory activity occ[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 63 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Change Display Default: E Selection: -, E, or P Function No. Function Name Alternate Keystroke 15 Change Displ ay [COMMAND][4][9] Use this function to select either a bright or dim display with loud or sof[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 64 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 View Log Default: E Selection: -, E, or P Function No. Function Name Alternate Keystroke 21 View Log (Menu f unction only) Use this function to view all of the system events, their time stamps , User IDs, [...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 65 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Reset Sens ors Default: E Selection: -, E, or P Function No. Function Name Alternate Keystroke 27 Reset Sensor s [COMMAND][4][7] Use this function to activate the Reset Sensors function for Fire or Intrus [...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 66 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Default Text Default: P Selection: -, E, or P Function No. Function Name Alternate Keystroke 34 Default Text [COMMAND][5][7] Determining the armed state of an area using the programm ed custom text migh t [...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 67 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Keypad Programming of the Keypad Programming Option D1255 1. Refer to Figure 1 on page 7 to access Keyp ad Programming and navigate to the DISABLE KP PROG option. Press [ENT]. 2. The current keypad program[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 68 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 L## Master Arm Delay Default: Re fer to the program record sheet Selection: - or E Function No. Function Name Alternate Keystroke 2 Master Arm Delay [COMMAND][1] Master arms areas based on the CC# Scope of[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 69 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 L## View Memory Default: Refer to the program record sheet Selection: - or E Function No. Function Name Alternate Keystroke 9 View Event Memory [COMMAND][4][0] View all memory events that occurred since th[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 70 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 L## Send Report Default: Refer to the program record sh eet Selection: - or E Function No. Function Name Alternate Keystroke 13 Send Report [COMMAND][4][1] or [COMMAND][4][2] Send a Test Report from any ke[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 71 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Table 26: L## Secure Door-Door Mode Definitions Door State Definition Lock Door Normal Door: When a door is in the Lock Door state, one can initiate the door sequence using Skeds, CYCLE DOOR?, keypad funct[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 72 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 L## Add User Default: Re fer to the program record sheet Selection: - or E Function No. Function Name Alternate Keystroke 18 Add User [COMMAND][5][6] Add or change users, add or change aut hority levels, a[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 73 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 L## Bypass a Point Default: R efer to the program record sheet Selection: - or E Function No. Function Name Alternate Keystroke 25 Bypass a Po int [COMMAND][0] Bypass points with this authority level. L## [...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 74 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2  Events print locally without alarm annunciation or reporting to the central station receiver.  D1255 Key pad display s a sequen tial coun t and the text for the poin t afte r each point is activated[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 75 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Custom Functions L## C Function 128 [through 143] Default: R efer to the program record sheet Selection: - or E Function No. Function Name Alternate Keystroke 128 throug h 143 Enable Custom Function 12 8 t[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 76 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 L## Disarm Level Default: Refer to the program record sh eet Selection: I, D, or - I Users change the Master Armed state and Perimeter Armed state to Perimeter Instant. The armed state does not change in o[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 77 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 2.10.8 SIA Duress Passcode Options USER INTERFACE  Authority Levels  L## Disarm USER INTERFACE  Authority Levels  L## Send Duress USER INTERFACE  Authority Levels  L## Passcode Disarm Gen[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 78 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 M## CC Address 1 [through 16] Default: R efer to the program record sheet Selection: Yes or No Yes This menu item appears at this keypad address. No T his menu item does not app ear at this keypad address.[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 79 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Relay functions that resume the proper state within one minute: Alarm Bell Perimeter Fault Summary Fire Summary Trouble Area Armed Reset Sensors Fire Bell AC Fail Summary Alarm Phone Fail Silent Alarm Summ[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 80 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 When sharing one relay to reset sensors in two or more areas, you must program the following. Failure to do so caus es TROUBLE PT ### for all point types programmed as P## Resettable .  CC # Scope must [...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 81 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 A# Duress Relay Default: 0 Selection: 0, 1 to 128 for D9412GV3, 1 to 64 for D7412GV3, A, B, or C Activates when a Duress alarm is generated from a keypad assigned to the specified area. Burg Time needs a b[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 82 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Comm Fail Default: 0 Selection: 0, 1 to 128 for D9412GV3, 1 to 64 for D7412GV3, A, B, or C Activates when a control panel cannot communicate a report after making ten attempts to each routin g destination.[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 83 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 2.1.1 User Groups For the D9412GV3, there are 249 groups (99 groups for the D7412GV3) consisting of one user with a passco de and token (maste r) and th ree us ers with tokens or cards but not a passcode ([...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 84 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 2.1.6 Reporting and Logging Phone # Format must be ModemIIIa 2 for the following reports sent to the central station. Regard less of the reporting format, they log and print at the local printer as shown i[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 85 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 User ### Default: 001 Selection: 000 or 001 to 249 (001 to 099 for the D7412GV3) Enter the User number you are programming. User 000 is the Serv ice Authority Level (Level 15). You cannot change the progra[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters EN | 86 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 U### Name Default: Refer to the program record sh eet Selection: Sixteen alphanumeric characters Enter Alphabetic-ch aracters A to Z in capital letters Period (.), comma (,), perce nt (%), parentheses [()][...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 3.0 Points EN | 87 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 3.0 Points 3.1 Point Index Use the poin t indexe s to cons truct person ality types for points used in the system. The Index nu mbers are used in Point As signments. Each un ique point index number determi nes the control panel?[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 3.0 Points EN | 88 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 P ## Type Description 2 Interior: Interior points are armed only by master arming t he area. They are not armed wh en using Perimeter Arming fu nctions. These points ar e typically used to monitor interior detec tion devices such[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 3.0 Points EN | 89 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 P ## Type Description Keyswitch Maintained: Program P## Pt Response as 1. Do not connect initiating devices to a Keyswitch point. Normal: The area is disarmed. Short: A short is a trouble when the area is disarmed. A short is an [...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 3.0 Points EN | 90 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 P ## Type Selection Description D279 (O/C Non-Priority): T he D279 provides point arming and disarmi ng independent of the area arm state. A non-p riority D279 point arm state does no t affect the area arm state. Point Response m[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 3.0 Points EN | 91 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 3.2 Point Responses 3.2.1 Applications for Point Responses 9 , D, and E: Combine Point Response s 9, D, and E with Perimeter point types to create more flexible 24-hour protection. Unlike 24-hour points, a faulted Perimeter point[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 3.0 Points EN | 92 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 P## Pt Response Default: Refer to the program record sheet Selection: 0 to F Controlled (Non-24-Hour Points) Point Response 0 1 2 3 4 5 6 7 8 9 A B C D E F Armed Open I I I I D D I I D I I I I I T Armed Short I I I I I I D D D I [...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 3.0 Points EN | 93 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 P## Entry Tone Off Default: No Selection: Yes or No Yes Disables the entry delay tone whe n this perimeter poin t is faulted. This is in tended for use with poin ts set to P## Type 1 (Perimeter). No A tone sound s at keypads when[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 3.0 Points EN | 94 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 When a po int progra mmed for P## Silent Bell is faulted, the timer for the A# B urg Time starts, eve n though the bell is not yet ri nging . As mu ch as 3 mi n can elapse before the second attempt fails. Ensu re that A# Burg Tim[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 3.0 Points EN | 95 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 P## Buzz On Fault Default: 0 Selection: 0 to 3 Selection Operation for Controlled Points (Point Types 1, 2, and 3) Operation for 24-hour, Fire and Aux AC Supervision Points (Po int Types 0 and 11) 0 Th e point buzzes at th e keyp[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 3.0 Points EN | 96 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 P## Watch Point Default: Refer to the program record sheet Selection: Yes or No Yes Activates Watch Mo de response s if the point is faulted wh ile the control panel is in Watch Mode. No Does not activate Watch Mode responses for[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 3.0 Points EN | 97 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Local While Disarmed suppresses all reports from 24-hour points. Do not use P## Type 0 f or this pro mpt. Remem ber that this option works only for Disa rmed points, an d a Type 0 is a 24-hou r Always Armed point. Instead, ch oos[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 3.0 Points EN | 98 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 P## Bypass Returnable Default: No Selection: Yes or No Yes This point automatically returns to the system when the area is disarmed. No This point sta ys out of the system through arming and disarmi ng cycles. Use this option to [...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 3.0 Points EN | 99 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 P## Swinger Bypass Default: No Selection: Yes or No Yes En able Swinger By pass for th is point. No Disable Swi nger Bypass for this point. To meet UL requirements, set th is parameter to No . Use the P## Swinger Bypass parameter[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 3.0 Points EN | 100 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 The Cross Point feature does not activate when a fault occurs on Controlled points (Point Types 1, 2 and 3) in the disarm ed, entry de lay, or ex it delay states. Refer to Section 5.9 Cross Point Paramete rs on page 139 for addi[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 3.0 Points EN | 101 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 When a sensor reset occurs, the control panel does not accept alarms from any poin ts w ith P## Resettable programme d as Yes . During the 5-sec reset time, alarms from these points are ignored. Do not mix fire an d intrusion de[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 3.0 Points EN | 102 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Keypad Programming of P### Point Index D1255 1. Refer to Figure 1 on page 7 to access Keyp ad Programming and navigate to the POINT PARAMET ERS option. The PT NUM 1 - ### option shows. 2. Enter the point number you wish to confi[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 3.0 Points EN | 103 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 P### Relay Default: Refer to the program record sheet Selection: 0 to 8 Use this option to ac tivate a relay when th e point is faulted. Refer to Table 28 . Relays do not activate for Fire Supervisory or Non-Fire Supervisory poi[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 3.0 Points EN | 10 4 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 3.4 COMMAND 7 and COMMAND 9 These en tries ass ign point in dexes, as sociated re lays that activate, and th e text for the COMMA ND 7 and COMMAND 9 keypad functions. CMD7 Point Index Default: 31 Selection: 0 to 3 1 This entry [...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 4.0 Schedules (Skeds) EN | 105 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 4.0 Schedules (Skeds) 4.1 Windows Use this programming mod ule to define the windows for Open ing an d Closin g and Us er Access . 4.1.1 Opening and Closing Use these windows to set a schedule for disarmi ng and armin[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 4.0 Schedules (Skeds) EN | 106 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 W# Mo nday Default: No Selection: Yes or No W# Tuesday Default: No Selection: Yes or No W# Wednesday Default: No Selection: Yes or No W# Thursday Default: No Selection: Yes or No W# Friday Default: No Selection: Yes o[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 4.0 Schedules (Skeds) EN | 107 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 W# Open Window Start Default: 00: 00 Selection: HH:MM (hours and minutes) Enter the time you want the control panel to start the Opening Window. T he window goes i nto effect at the beginning of the minute. Make time [...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 4.0 Schedules (Skeds) EN | 108 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Table 30: Programming for Two Same Day Opening Windo ws (refer to Figure 5 ) Open C lo se W# Day of Week Early Begin Start Stop Early Begin Start Stop eXcep t On Holiday Holiday Index Area(s) 1 S M T W T F S 06: 00 07[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 4.0 Schedules (Skeds) EN | 109 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 If the window must activate on th e same day as it is programmed, reboot the control panel to activate the window immed iately. W# Close Window Start Default: 00: 00 Selection: HH:MM (hours and minutes) Enter the time[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 4.0 Schedules (Skeds) EN | 110 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 W# Xept Holiday Default: No Selection: Yes or No Yes Do no t activate this win dow on holidays. To use this selection, the window must be programmed to activate on at least one day of the week and a Holiday In dex mus[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 4.0 Schedules (Skeds) EN | 111 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Table 33: Opening and Closing Win dows Worksheet Open C lo se W# Day of Wee k Early Begin Start Stop Early Begin Start Stop eXcep t On Holiday Holiday Index Area(s) 1 S M T W T F S _ _ : _ _ _ _ : _ _ _ _ : _ _ _ _ : [...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 4.0 Schedules (Skeds) EN | 112 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Table 36: Delivery Schedule* Open C lo se W# Day of Wee k Early Begin Start Stop Early Begin Start Stop eXcep t On Holiday Holiday Index Area(s) 3 S M T W T F S 02 : 30 02 : 45 03 : 00 03 : 05 03: 15 03: 30 Yes No 1 2[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 4.0 Schedules (Skeds) EN | 113 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 UW# Sunday Default: No Selection: Yes or No This prom pt, and th e next s ix day o f the we ek prompts, select the days of the week that the User Group Window is active. Refer to the W# Sunday prompt in Section 4.1.1 [...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 4.0 Schedules (Skeds) EN | 114 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 4.1.3 Holiday Indexes for User Group Win dows You can enable up to four Holiday Indexes to use wit h User Group Windows. Enable at least one Holiday Index if UW# Xept Holiday is programmed as Yes for this user window,[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 4.0 Schedules (Skeds) EN | 115 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Default: 0 Selection: 0 to 24, 28, 29 S## Ar ea 1[through #] 1 Arm Area: Th is function simulates the Master Ar m Delay keyp ad function. Entries in th e S## Area # prompts define the area(s) this sked arms. The sked [...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 4.0 Schedules (Skeds) EN | 116 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Default: 0 Selection: 0 to 24, 28, 29 S## Area 1[through #] Yes Unbypa ss all points in Area #. 5 Unbypass Al l Points: This function is not available as a key pad function. The entry in the S## Area # prompt defines [...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 4.0 Schedules (Skeds) EN | 117 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Default: 0 Selection: 0 to 24, 28, 29 S## Defer Test Yes Defer the Test Report. Default: No Selection: Yes or No Enable sked to defer the Test Report No Send the Test Report on schedule. S## Hourly Report Yes Send the[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 4.0 Schedules (Skeds) EN | 118 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Default: 0 Selection: 0 to 24, 28, 29 S## Cmd Center Default: Blank (0) Selections: Blank (0), 1 to 8 Blank (0) No keypad is specified for Custom Function activation. Identify the specific key pad (CC #) where the Cus[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 4.0 Schedules (Skeds) EN | 119 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Default: 0 Selection: 0 to 24, 28, 29 13 Adjust Time Forward One Hour : This s ked function is used to make adjustmen ts to the control panel’s clock. A typical application is to program th is to go into effect at 2[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 4.0 Schedules (Skeds) EN | 120 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Default: 0 Selection: 0 to 24, 28, 29 S## Access Ctl Level # Default: No Yes Turn off access for level #. 17 Access Control Level Off: This function emulates the ACCESS CMD LEVEL command that determ ines whether a use[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 4.0 Schedules (Skeds) EN | 121 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Default: 0 Selection: 0 to 24, 28, 29 S## Door 1 [through 8] Default: No Selection: Yes or No Yes Disable the sendi ng of Access Grant ed Ev ents for Door #. 22 Access Authority Events Off: The contr ol panel can log [...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 4.0 Schedules (Skeds) EN | 122 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 29 Non-Expanded Off-Normal Test Repo rt: Non- Expanded O ff-Norm al Test Re port Events are only sent when any point is in the off-normal state from any area, but only sends the Off Normal Test Report Event. Any syste[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 4.0 Schedules (Skeds) EN | 123 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 S## Time Default: 00:00 Selection: HH:MM (hours and minutes) Enter the time that the sked executes. Make entries using a 24-hour clock (for example, 7:00 AM is entered as 07:00, 2: 45 PM is en tered as 14 :45). Disabl[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | EN | 124 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 S## Holiday # Default: None Selection: Yes or No Yes Use Holiday Index 1 with this sked. No Do not use Holiday Index 1 with this sked. 4.3 Holiday Indexes This programming module has two sectio ns: Add/Change/Delete a nd View Holidays. Use[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 5.0 AUXPARM EN | 125 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 5.0 AUXP ARM 5.1 Introduction The programming p rompts in this sectio n are primarily used for programmi ng enhanced communication capabilitie s for the GV3 Series Contr ol Pane ls. Enhanced communications is the ability to pro[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 5.0 AUXPARM EN | 126 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Statu s Rate Default: 0 Selection: 0 to 255 0 Status information is sent on ly when requested. 1 to 255 Status information is sent at the interval programmed. If the Status Rate is set to a value less than 10, and 1 to 6 SDI de[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 5.0 AUXPARM EN | 127 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 5.4.1 Configuration for RPS Over Network COMMAND 43 (Remote Programmi ng) can establish communication with RPS over the phone or over the network. Figure 6 on page 128 and Figure 7 on page 129 show the structure of COMMAND 43. [...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 5.0 AUXPARM EN | 128 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Figure 6: COMMAND 43 Flow Chart (D1255) Command 43, Remote Program RPS via phone Enter choice: Use port 7700> Enter Port Number> <Exit rps via Port 7700 RPS connecting... via phone (via network) <Exit RPS connecting[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 5.0 AUXPARM EN | 129 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Figure 7: COMMAND 43 Fl ow Chart (D1265) ALLOW ANSWER ? COMMAND 4 3 RPS VIA PHONE ? NEXT NEXT ENT USE PORT ## ### ? NEXT NEXT RPS CONNEC TING ENT RPS CONNECTING ENT (or ringing) RPS VIA NETWORK? NEXT ENTER PORT NUM ? ##### ENT [...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 5.0 AUXPARM EN | 130 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 RPS IP Addr ess # Default: 0.0.0. 0 Selection: 0.0. 0.0 to 255.255.255.255 0 to 255 There are four n umbers for an IP address. Leading zeros are not required. This prompt contains the IP address for RPS. An IP address has four [...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 5.0 AUXPARM EN | 131 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 5.5 Programming Path Numbers and IP Addresses for Enhanced Communications Enhanced communication s is the ability to communicat e by some means other than the standard digital diale r. In this section, pr ogrammable parameters [...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 5.0 AUXPARM EN | 132 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Refer to Keypad Programming of Path # IP Address, Path # Port Number, and Path # Poll Rate on page 132. Path # Poll Rate Default: 0 Selection: 0, 5 to 65535 sec 0 Disables the heartbeat poll (not recommen ded, refer to the firs[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 5.0 AUXPARM EN | 133 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 8. The keypad shows the currently configured IP address. Press [NEXT]. The currently co nfigured port num ber shows. 9. Press [ENT] to change the port number. 10. The [PREV] button ac ts as a [Backspace] key. Press [PREV] to de[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 5.0 AUXPARM EN | 134 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 When the control panel first powers up, the first Heartbeat Poll for Path 1 is sent and is acknowledged in 1 sec. 120 sec after the first Heartbeat Poll is sent, the secon d Heartbeat Poll for Path 1 is generated and sent to th[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 5.0 AUXPARM EN | 135 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Example of Retry Count: An ackn owledgm ent of th e heartbe at was not received wit hin 10 sec. The control p anel sends t h e next Heartbeat Poll after the first 10-sec ACK wait period expires. If the central station does not [...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 5.0 AUXPARM EN | 136 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 This item determines whether the NIM is supervised. If the NIM is supervised, disconnecting it from the control panel creates a Trouble SDI 88 Event and the keypad annunciates a troub le tone and displays SERVC SDI 88 . Supervi[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 5.0 AUXPARM EN | 137 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 5.8 Miscellaneous Fire Summar y Su stain Default: No Selection: Yes or No Yes Forces the Sum mary Fi re relay output to remain on after the Alarm Silence command. No Allows Summ ary Fire relay output to be silent when the Fire [...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 5.0 AUXPARM EN | 138 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 For SIA CP-01 Compliance: Abort Window is a required parameter. To meet UL requirements, the comb ined Entry Delay tim e and Abort Win dow time must not e xceed 60 sec. F or Entry D elay time programming information, refer to P[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 5.0 AUXPARM EN | 139 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Perimeter Relay Default: No Selection: Yes or No Yes Ch ange the function of the area-wide fail-to-close relays to follow the perimeter armed states of their areas. No The area-wide fail-to-close relay operates normally. When s[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 6.0 ACCESS CONTROL EN | 14 0 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Table 38: Cross Point Ranges Within Grou ps Cross Point Group Point Range 1 1 to 8 2 9 to 16 3 17 to 24 4 25 to 32 5 33 to 40 6 41 to 4 8 7 49 to 56 8 57 to 64 9 65 to 72 10 73 to 80 11 81 to 88 12 89 to 96 13 97 to 104[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 6.0 ACCESS CONTROL EN | 141 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 All SDI devices, regardless of area assigned, report to Area 1, Account 1 by default upon SDI failure. If a D9210B becomes d isconnected, an S DI Fail ## and a Missing Point ### Event is created. If the D9210B is not pro[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 6.0 ACCESS CONTROL EN | 142 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Door points must be programmed as Perimeter po ints. If a 24-hour po int type is required for the Door poin t, you can use a Perimeter point type with a point response of 9 to C. Also, t he debounce count mus t be set to[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 6.0 ACCESS CONTROL EN | 143 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 This comm and unloc ks the do or regardless of the armed state. Each fire alarm that is generated causes a Door Unlocked – Automatic Event. D# Disarm on Open? Default: Yes Selection: Yes or No Yes The area disarms only[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 6.0 ACCESS CONTROL EN | 144 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 D# Buzz Time Default: 2 sec Selection: 0 to 24 0 sec 0 Buzz Time is not programmed for this door. 1 to 240 The buzzer sounds for the amount of time programmed. Enter the amount of time the buzzer output sounds to notify [...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 6.0 ACCESS CONTROL EN | 14 5 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 D# REXShunt Only? Default: No Selection: Yes or No Yes Programme d shunt tim e activates so the door can be manual ly opened. No REX automatically activates the programme d strike an d shunt tim e. Use this program item[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 6.0 ACCESS CONTROL EN | 146 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 D# Enter Request? Default: No Selection: Yes or No Yes A Door RTE Event from this door controller is sent to the control panel for processing. No A Door RTE Even t from this door controller is not sent to the control pan[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | 7.0 SIA CP-01 Quick Reference EN | 147 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 7.0 SIA CP-01 Quick Reference Table 40: Programming the Control Panels for SIA CP--01 Compliance Prompt Name Bosc h Recommende d Settings for SIA CP-01 Compliance Shipping Defa ult Referenc es Phone # (Prefix [...]

D9412G V3/D 7412 GV3 | Program Entry Guide | Progr amming Prompts Directory EN | 148 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Programming Pr ompts Directory Panel and Area Wide Parameters ................ 12 Phone ....................................................... 12 Phone # ............................................ 12 Phone[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | Progr amming Prompts Directory EN | 149 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Open/Close Op tions .............................. 43 A# Account O/C ................................. 44 A# Area O/C ...................................... 45 A# Disable O /C in Window ................. 45 A[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | Progr amming Prompts Directory EN | 150 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Authority Le vel ................................... 67 L## Disarm ........................................ 67 L## Master Arm Delay ....................... 68 L## Master Arm Instant L## Perimeter In stant ...[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | Progr amming Prompts Directory EN | 151 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 U### User Gr oup ............................... 85 U### Area 1 [ through Area #] Auth .... 85 U### Name........................................ 86 U### Mstr S ite ................................... 86 U### [...]

D9412G V3/D 7412 GV3 | Program Entry Guide | Progr amming Prompts Directory EN | 152 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 UW# Xept Holiday............................ 11 4 UW# Holiday 1 [ through 4] ............... 11 4 Schedules (Skeds) ................................ 114 Sked Numb er ................................... 114 S#[...]

D9412G V3/D 7412 GV3 | Program Entry Guide | Progr amming Prompts Directory EN | 153 Bosch Se curity Syst ems, Inc. | 10/11 | F01U 170807-0 2 Strike Profile .......................................... 143 Door # .............................................. 143 D# Str ike Time ................................. 1 4 3 D# Shunt Ti me .................[...]

Bosch Security Systems, Inc. 130 Perinton Parkway Fairport, NY, 14450 USA www.boschsecurity.com © Bosch Security Systems, Inc. 201 0[...]