Bosch Appliances D9412GV4 manual

Control Panel D9412GV4/D7412GV4 v2.00 en UL Installation Instructions[...]

[...]

Table of contents 1 Introduction 4 1.1 About documentation 4 1.2 Determine Bosch Security Systems, Inc. Product Manufacturing Dates 4 2 Installation 5 2.1 Installation Preparation 5 2.2 Enclosure Options 5 2.3 Mounting Enclosure 5 2.4 Installing the Control Panel 6 2.5 Connecting Earth Ground 7 2.5.1 Terminal 10 7 2.5.2 Ground Fault Detect Enable 7[...]

Introduction About documentation Copyright This document is the intellectual property of Bosch Security Systems, Inc. and is protected by copyright. All rights reserved. Trademarks All hardware and software product names used in this document are likely to be registered trademarks and must be treated accordingly. Determine Bosch Security Systems, I[...]

Installation Installation Preparation This section contains a general installation procedure and refers to other sections of the document for detailed instructions. Review this document and the D9412GV4/D7412GV4 Program Entry Guide (P/N: F01U265459) before beginning the installation to determine the hardware and wiring requirements for the features[...]

i Notice! Electromagnetic interference (EMI) can cause problems on long wire runs. Figure 2.1: Enclosure Mounting Callout - Description 1 - Point chart label 2 - Mounting skirt hooks (2) 3 - Module mounting holes (12) 4 - Tamper switch mounting holes (5) 5 - Skirt mounting hole (1) 6 - Enclosure mounting holes (5) 7 - Mounting skirt hook holes (2) [...]

Connecting Earth Ground Terminal 10 To help prevent damage from electrostatic charges or other transient electrical surges, connect the system to earth ground at Terminal 10 before making other connections. Recommended earth ground references are a grounding rod or a cold water pipe. ! Warning! Do not use telephone or electrical ground for the eart[...]

Figure 2.2: Ground Fault Detect (S4) Callout - Description 1 - S4 Locked (Closed). Control panels detects ground faults. 2 - S4 Unlocked (Open). Control panel does not detect ground faults. Ground Fault Impedance Specifications The table below provides the impedance specifications for detecting ground faults when any terminal or field wiring is sho[...]

Figure 2.3: Reset Pin Callout - Description 1 - Reset pin locked (closed) 2 - Reset pin normal (open) Control Panel Installation | en 9 Bosch Security Systens, Inc. UL Installation Instructions 2012.12 | 02 | F.01U.265.462[...]

Diagrams Faceplates Figure 3.1: Faceplates Callout - Description Callout - Description 1 - Charging status LED (yellow) 8 - Ring 2 - Low battery LED (red) 9 - Operation monitor LED (green) 3 - Color-coded battery leads 10 - Accessory connector 4 - Ground fault detect enable 11 - Reset pin 5 - Phone LED (red) 12 - SDI interconnect wiring connector 6[...]

Power Supply Side Wiring Diagrams D9412GV4/D7412GV4 Power Supply Side System Wiring Diagram (Power and Phone) Figure 3.2: Side System Wiring Diagram Callout - Description Callout - Description 1 - If required by local AHJ, connect D113 Battery Lead Supervision Module. 8 - To Output A or Output B 2 - Batteries 9 - Listed Audible Signaling Devices ra[...]

i Notice! For UL Certified accounts, additional power can be obtained using only a UL Listed auxiliary 12.0 VDC regulated, power-limited power supply. i Notice! All terminals accept for Outputs A, B, and C (Terminals 6, 7 and 8) are supervised. D9412GV4/D7412GV4 Input Points and Peripheral Devices System Wiring Diagram Figure 3.3: Input Points and [...]

i Notice! For D129, use zero retard except for waterflow devices. All external connections except Terminal 5 (battery positive) are power limited. Control Panel Diagrams | en 13 Bosch Security Systens, Inc. UL Installation Instructions 2012.12 | 02 | F.01U.265.462[...]

SDI Devices Wiring Diagrams D9412GV4 SDI and Zonex Devices System Wiring Diagram Figure 3.4: D9412GV4 System Wiring Diagram, SDI and Zonex Devices Callout ￚ Description Callout ￚ Description 1 ￚ Up to 16 supervised D1265, D1255 (all versions), D1255RB, D1256RB Keypads, or D1257RB Fire Annunciators, or up to 8 supervised D1260 Keypads (all ver[...]

i Notice! Terminals 24 through 36 are power limited, supervised. Fire and Intrusion devices must be on separate circuits. Refer to ICP-SDI-9114 Installation Instructions (P/N: F01U030068) D7412GV4 SDI and Zonex Devices System Wiring Diagram Figure 3.5: D7412GV4 SDI and Zonex Devices System Wiring Diagram Callout - Description 1 - Up to 16 supervise[...]

i Notice! Terminals 24 through 36 are power limited, supervised. Fire and Intrusion devices must be on separate circuits. Refer to ICP-SDI-9114 Installation In- structions (P/N: F01U030068). D9412GV4/D7412GV4 SDI2 Devices System Wiring Figure 3.6: SDI2 Devices System Wiring Diagram Callout - Description 1 - B208 Octo-input Modules 1 2 - B308 Octo-o[...]

Module D9412GV4 D7412GV4 4 BB810/B820 SDI2 Inovonics Interface Modules 1 1 B920 Two-line Alphanumeric Keypad 5 16 16 B930 ATM Style Alphanumeric Keypad (SDI2) 5 16 16 B520 Auxiliary Power Supply Module 8 8 1 For the D7412GV4, only 5 inputs are available on the Octo-input at address 7. 2 For the D7412GV4, only 4 outputs are available on the Octo-out[...]

SDI2 Bus Wiring Recommendations Use the following SDI2 bus wiring recommendations for SDI2 installation. The SDI2 bus is used by the GV4 Control Panel and corresponding modules to communicate with one another. Modules can be connected via home run, daisy chain, or single level T-tapped anywhere on the SDI2 bus. Please reference Figure 2.7 below. Fi[...]

Cable capacitance Overall cable length Cable capacitance Overall cable length Cable capacitance Overall cable length Cable capacitance Overall cable length pF/ft ft pF/ft ft pF/ft ft pFf/ft ft < 17 7500 22 6363 27 5185 32 4400 18 7500 23 6086 28 5000 33 4242 19 7350 24 5800 29 4828 34 4100 20 7000 25 5600 30 4700 35 4000 21 6666 26 5385 31 4516 [...]

Power Supply and Power Outputs Power Supply - Primary Primary (AC) Power Circuit The primary source is a 16.5 VAC, 40 VA, internally-fused transformer (Bosch Security Systems, Inc. Model D1640). The control panel draws 225 mA when idle and 300 mA when in an alarm state. The total available auxiliary current is 1.4 A. Transient suppressors and spark[...]

D8004 Transformer Enclosure Required for Fire Systems Use the D8004 Transformer Enclosure for the D1640 Transformer in fire and combined fire and burglary applications. i Notice! Check with the Authority Having Jurisdiction (AHJ) about mounting transformers on specific circuits. Power Terminals - Secondary Secondary (DC) Power A 12 V, 7 Ah (up to 1[...]

! Warning! High current arcs are possible. The positive (red) battery lead and Terminal 5 can create high current arcs if shorted to other terminals or the enclosure. Use caution when working with the positive lead and Terminal 5. Always disconnect the positive (red) lead from the battery before removing it from Terminal 5. ! Warning! The battery t[...]

Figure 4.2: Non-PowerLimited Wiring Callout ￚ Description 1 ￚ Conduit required for use with external batteries. 2 ￚ Battery wires 3 ￚ 0.25 in (6.4 mm) minimum. To ensure proper spacing, use tie-wraps or similar devices to secure wires. 4 ￚ Relay output wires 5 ￚ Input or Zone wires 6 ￚ Standby battery Power Outputs - Circuit Protectio[...]

– Terminal 8: Output C (Switched Auxiliary Power) PTC CB5 protects Terminal 24: Zonex Power. PTC CB1 protects Terminal 32: SDI Power +. PTC CB3 protects Terminal 36: SDI2 Power +. Required by UL: – All devices powered from a power output are to be supervised. – Power outputs are not shared between fire and non-fire devices unless all devices [...]

F01U265459) contains complete instructions for programming outputs. Refer to Terminals 6 and 7, page 25 , Fire System Power Formula, page 25 , and Terminal 8, page 26 for descriptions of the functions of each terminal. Refer to the Bell Parameters section of the program to set the Fire Bell, Alarm Bell, and Gas Bell output responses for outputs. Fo[...]

Terminal 8 Terminal 8 provides continuous positive (+) 12.0 VDC Nominal power. Output C interrupts the power at Terminal 8 when activated. Use Terminal 8 to power smoke detectors or other devices that are reset by interrupting power. One self-resetting circuit breaker protects Terminals 6, 7, and 8 against shorts. Verification/Reset Output The defa[...]

Specifications Voltage Input (Power Supply) 1 Primary: Terminals 1 and 2 16.5 VAC 40 VA class 2 plug-in transformer (D1640) Secondary: Terminals 4 and 5 Sealed lead-acid rechargeable battery (12.0 VDC, 7 Ah or 12.0 VDC, 17.2 or 18 Ah). The control panel supports up to two 12.0 VDC, 7 Ah batteries using the D122/ D122L Dual Battery Harness or two D1[...]

SDI Bus B-: 9 VDC 15000 (4572 m) maximum SDI2 Bus SDI2 Bus A+; 12 VDC nominal 7500 ft (2286 m) maximum 3 SDI2 Bus B-: 12 VDC nominal (7500 ft) (2286 m) maximum 3 Telephone Connections Connection: RJ31X or RJ38X jack can connect the control panels. Two telco lines: Bosch Security Systems, Inc. D928 Dual Phone Line Module required for two phone line [...]

B520 Specifications Voltage Input (Power Supply) Primary: 18 VAC terminal 18.0 VAC, 50 VA class 2 plug-in transformer -TR1850 (18.0 VAC, 50 VA class 2 plug-in transformer – TR1850-CA for Canada) Secondary: Batt 1, Batt 2 terminals The B520 Auxiliary Power Supply Module supports the connection of two independantly monitored sealed lead-acid rechar[...]

Recharge Cycle AC ON – Load shed relay resets, battery charging begins, Battery Trouble and AC Restoral Reports sent. 12.6 VDC – Battery Restoral Report sent, Low Battery LED off. Environmental Temperature: +32 ﾟ F to +120 ﾟ F (0 ﾟ C to +49 ﾟ C) Relative Humidity: Maximum 93% non-condensing Compatible Enclosures D8103 Universal Enclosur[...]

Terminal No Terminal Description Requirements 16 POINT 4 Terminal accommodates 14 to 22 AWG, use appropriate wire size based on loop resistance less than 100 Ω. 17 POINT 5 Terminal accommodates 14 to 22 AWG, use appropriate wire size based on loop resistance less than 100 Ω. 18 POINT 5/6 COMMON Terminal accommodates 14 to 22 AWG, use appropriate [...]

Terminal No Terminal Description Requirements 36 SDI2 POWER Terminal accommodates 14 to 22 AWG, use appropriate wire size based on peripheral device current. *D9412GV4 only. Terminals 25 and 26 are NOT USED on the D7412GV4 Control Panel. Compatibilities i Notice! Where the fire alarm transmitter is sharing on-premise communications equipment, the s[...]

Model Title UL 864 UL 985 Intrusion cUL Intrusion D1218 12 V, 17.2 Ah Rechargeable Battery D1255/D1255B Keypads (General Purpose) X X X D1255W Text Keypad (white) X X X D1260/ D1260B 2 Keypads X X X D1640 16.5 VAC 40 VA Transformer X X X D1640-CA 16.4 VAC 40 VA Transformer for Canada X D8004 Transformer Enclosure X X X D8125 POPEX Module X X X X D8[...]

Model Title UL 864 UL 985 Intrusion cUL Intrusion 3 RFRP-A RADION repeater X X 3 RFPR-12-A RADION PIR X 3 RFPR-C12_A RADION PIR C X 3 RFUN RADION universal transmitter X 1 Where the fire alarm transmitter is sharing on-premise communications equipment, the shared equipment must be UL Listed (ITE or fire potective signaling). 2 Version 1.04 or above[...]

[...]

Bosch Security Systems, Inc. 130 Perinton Parkway Fairport, NY 14450 USA www.boschsecurity.com © Bosch Security Systems, Inc., 2012[...]