Bosch Appliances HMV9306 manual

Household Appliances Over -the-Range Microwave Installation Instructions For Models: HMV9302, HMV9305, HMV9306, HMV9307 PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING IMPORT ANT : Save these instructions for the local electrical inspector’ s use. INST ALLER: Please leave these Installation Instructions with this unit for the owner . OWNER: Ple[...]

2 YOUR SAFETY FIRST BEFORE YOU ST ART • Proper installation is the installer's responsibility! – Read the entire manual before you begin. The Model number label is located on the oven front. See Figure 1. Mounting plate is located on back side of microwave oven. See Figure 2. BE SURE TO READ THE FOLLOWING SAFETY INSTRUCTIONS: FOR YOUR SAFE[...]

3 • THIS APPLIANCE MUST BE GROUNDED![...]

4 • MAKE SURE YOU HAVE ENOUGH SPACE AND SUPPORT. – Mount the oven against a flat, vertical wall, so it is supported by the wall. The wall should be constructed of minimum 2" x 4" wood studding and 3/8" thick drywall or plaster/lath. – ATTACH AT LEAST ONE of the two lag screws supporting the oven to a vertical, 2" x 4"[...]

5 THE FOLLOWING PARTS ARE SUPPLIED WITH THE OVEN: P AR TS, TOOLS, MA TERIALS Damper/duct connector (for roof vented or wall vented installation) Not Actual Size Four 1/4" x 2" lag screws - Actual Size (for wall stud holes) Four 1/4" x 3" toggle bolts - Actual Size (for drywall holes) Two 1/4" x 3" bolts - Actual Size O[...]

6 YOU WILL NEED THE FOLLOWING TOOLS AND MATERIALS FOR THE INSTALLATION: Carton or other heavy material for covering the counter top. • If you have brick or masonry walls, you will need special hardware and tools. • The ductwork you need for the installation is not included. All wall and roof caps must have a back-draft damper (shown on page 5).[...]

7 A VOID ELECTRICAL SHOCK! THIS APPLIANCE MUST BE GROUNDED! 1. Locate the grounded electric outlet for this oven in the cabinet above the oven, as shown in Figure 4 Detail. 2. You will cut the power-supply-cord hole (shown in Figure 4 Detail) later when you prepare the wall and upper cabinet in Step 4. Improper grounding could result in electric sh[...]

8 THIS OVEN MUST BE PROPERLY VENTED! You may vent your oven in one of three ways: Roof-venting If your oven is located on an outside wall near the roof, as in Figures 5 (3 1 / 4 " x 10" duct) and 8 (6" round duct.) Wall-venting If your oven is located on an outside wall on the first floor of your house, as in Figure 7 (3 1 / 4 "[...]

9 STEP 2: PREP ARE THE VENTING SYSYTEM ST ANDARD FITTINGS DUCT LENGTH The total length of the duct system, including straight duct, elbows, transitions, wall or roof caps must not exceed the equivalent of 140 feet. For best performance, do not use more than three 90 degree elbows. Below are the standard fittings and their equivalent length in feet.[...]

10 Your microwave oven is shipped with the blower assembled for roof venting. You need to adjust the blower if you want wall-venting or room-vented (recirculating) installation. ELECTRICAL SHOCK HAZARD! UNPLUG UNIT BEFORE WORKING ON IT . • DO NOT PULL OR STRETCH THE BLOWER WIRING! Pulling and stretching the blower wiring could result in electrica[...]

11 W ALL-VENTED INST ALLA TION: 1. Remove one blower unit mounting screw and one blower plate screw. Remove the blower plate from cabinet. See Figure 13. 2. Carefully lift the blower unit out of the microwave oven. 3. Use side cutters or tin snips to cut and remove knockouts “B” from Back plate. Discard knockouts. Be careful not to distort the [...]

12 STEP 3: PREP ARE THE VENTING BLOWER ROOM-VENTED (Recirculating) INST ALLA TION: 1. Remove one blower unit mounting screw and one blower plate screw. Remove the blower plate from cabinet. See Figure 19. 2. Carefully lift the blower unit out of the microwave oven. 3. Rotate blower unit 90 ˚ so the exhaust ports face the front of the cabinet. See [...]

13 MEASURE AND T ACK / T APE UP THE TEMPLA TES 1. Using a plumb line and (metal) measuring tape, find and mark the vertical center line on the back wall, as in Figure 22. 2. Find and mark one or two points where the studs are on the wall (Studs are normally 16 inches apart) and then measure and mark the stud locations. If you cannot find any wall s[...]

14 DRILLING THE HOLES IN THE W ALL AND UPPER CABINET : BE VER Y CAREFUL WHEN DRILLING HOLES INTO THE W ALL. Electrical wires could be concealed behind the wall covering and if the drill hits them you could get an electric shock. 1. Find the points on the mounting plate labeled A, B, C , and D . Drill a 3/16" diameter hole at any of these point[...]

15 STEP 5: INST ALL THE MOUNTING PLA TE TO THE W ALL 1. Draw a vertical line on the wall at the center of the 30 ″ wide space. Use the mounting plate as the template for the rear wall. Place the mounting plate on the wall, making sure that the tabs are against the bottom of the cabinet. Line up the notch and center line on the mounting plate to t[...]

16 STEP 5: INST ALL THE MOUNTING PLA TE TO THE W ALL TO PREP ARE THE REAR W ALL CUTOUT OPENING AND EXHAUST ADAPTOR/MOUNTING PLA TE FOR W ALL-VENTED: 1. Place the mounting plate against the rear wall as described in step 5 item 1 (page 15). 2. Using a pencil, put dots through slots F and G, and through holes H and I. Remove the mounting plate and dr[...]

17 STEP 6: A TT ACH THE OVEN TO THE W ALL You will need two people to lift this microwave. Failure to use more than one person could result in personal injury . 1. Carefully lift microwave oven and hang it on support tabs (See Figure 26 on the page 15) at the bottom of the mounting plate. Reaching through upper cabinet, thread power supply cord thr[...]

18 STEP 6: A TT ACH THE OVEN TO THE W ALL 5. Roof vented installation: See Figure 32 Install ductwork through the vent opening in the upper cabinet. Complete the venting system through the roof according to the method needed. See “ PREPARE THE VENTING SYSTEM, ” step 2 on the page 8. Use caulking to seal exterior roof opening around the exhaust [...]

Installation Notes[...]

Printed in Korea P/No.: 3828W5U0310[...]