Bosch Appliances X40 SN manual

VideoJet X40 SN Network Video Server en Installation and Operating Manual[...]

VideoJet X40 SN[...]

VideoJe t X40 SN Table of Cont ents | en 3 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 T able of Contents 1P r e f a c e 7 1.1 About this Manual 7 1.2 Conventions in this Man ual 7 1.3 Intended Use 7 1.4 EU Directives 8 1.5 Rating Plate 8 2 Safety Information 9 2.1 Electric Shock Hazard 9 2.2 Installation and Oper[...]

4 en | Table of Cont ents VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 5.19 Advanced Mode: Encoder Profile 48 5.20 Advanced Mode: Audio 52 5.21 Advanced Mode: Storage Management 53 5.22 Advanced Mode: Remote Video Device 56 5.23 Advanced Mode: Recording Profiles 57 5.24 Advanced Mode: Retention Tim[...]

VideoJe t X40 SN Table of Cont ents | en 5 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 8.3 Malfunctions with iSCSI Connections 112 8.4 LEDs 113 8.5 Processor Load 114 8.6 Network Connection 114 8.7 Serial Interface 114 8.8 Terminal Block 115 8.9 Communication with Terminal Program 116 8.10 Copyrights 118 9 Specifi[...]

6 en | Table of Cont ents VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems[...]

VideoJe t X40 SN Preface | en 7 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 1P r e f a c e 1.1 About this Manual This manual is intended for persons responsibl e for the installation and operation of the VideoJet X40 SN. International, national and any regional electrical engineering regulations must be followed a[...]

8 en | Preface VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 1.4 EU Dir ective s The VideoJet X40 SN network vi deo server complies with the requirements of EU Directives 89/336 (Electromagnetic Compatibility) an d 73/23, amended by 93/68 (Low Voltage Directive). 1.5 Rating Plat e For exact identifi[...]

VideoJe t X40 SN Sa fe ty In for m at io n | e n 9 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 2 Safety Information 2.1 Electric Shock Hazard – Never attempt to connect the unit to any powe r network other than the type for which it is intended. – Use only power supply units with UL approv al and a power outpu[...]

10 en | S afe t y I nfo rm at io n VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems[...]

VideoJe t X40 SN Product De scription | en 11 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 3 Product De scription 3.1 Scope of Deliver y – VideoJet X40 SN network video server – 4 terminal blocks – Quick Installation Guide – Product CD with the following content: – Quick Installation Guide –M a n u a l [...]

12 en | Product Descrip tion VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 3.2 Sy stem R equirements General Requirements – Computer with Windows XP or Windows Vista operating system – Network access (Intranet or I nternet) – Screen resolution 1,024 × 768 pixels – 16- or 32-bit color depth [...]

VideoJe t X40 SN Product De scription | en 13 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 3.3 Over view of F unctions Network Video Server The VideoJet X40 SN is a compact network video server fo r four connected video sources. It is primarily designed for en coding video, audio a nd control data for transfer over[...]

14 en | Product Descrip tion VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems Remote Control For remote control of exte rnal units such as pa n or tilt heads for came ras or motorized zoom lenses, control data is transmitte d via the VideoJet X40 S N's bidirectional serial interface. This interfac[...]

VideoJe t X40 SN Product De scription | en 15 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 Summary The VideoJet X40 SN provides th e following main functions: – Video and data transmissi on over IP data networks – Dual Streaming function for the encoder for si multaneous encoding with two individually definable[...]

16 en | Product Descrip tion VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 3.4 Connections on the F ront Panel 1U S B inte rface for future expansion of functions 2V i d e o I n 1 to Video In 4 video inputs BNC sockets for connecting video sources 3 Audio In audio line input 3.5 mm stereo socket for[...]

VideoJe t X40 SN Product De scription | en 17 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 3.5 Connections on the Rear Panel 7E T H RJ45 socket for connecting to an Ethernet LA N (local network), 10/100 MBit Base-T 8E T H LED lights up yellow when the unit is connected to the n etwork via ETH 9 Terminal block for a[...]

18 en | Product Descrip tion VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems[...]

VideoJe t X40 SN Installation | en 19 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 4 Installation 4.1 Preparations Please ensure the following installation conditions: – Do not install the unit close to heaters or other heat sources. Avoid locations exposed to direct sunlight. – Allow sufficient space for runni[...]

20 en | Installation VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 4.3 Connections Cameras You can connect four video so urces to the VideoJet X40 SN. Any cameras and other video sources that produce a standard PA L or NTSC signal are suitable. 1. Connect the cameras or other video sources to the BN[...]

VideoJe t X40 SN Installation | en 21 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 1. Carefully slide the CF card, top side do wn , into the slot as far as it will go. 2. To remove the CF card, simply pull it out. Data Interface The bidirectional data interface is used to co ntrol units connected to the VideoJet X4[...]

22 en | Installation VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems Relay Outputs The VideoJet X40 SN has four relay outputs for switching external units such as lamps or alarm sirens. You can operate these relay outputs manually while there is an active connection to the VideoJet X40 SN. The outputs[...]

VideoJe t X40 SN Installation | en 23 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 Backup Power Supply If the VideoJet X40 SN doe s no t have a permanent power supply, it may be nece ssary to supply the internal clock separ ately. To do this, you can connect the VideoJet X40 SN directly to a battery via the BP and [...]

24 en | Installation VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 4. 4 Power On /Powe r O f f Power Supply The VideoJet X40 SN does not have a power s wit ch. Power is supplied via a separate unit. Connect the VideoJet X40 SN to the power s upply un it and plug this into the mains. The unit is now [...]

VideoJe t X40 SN Installation | en 25 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 Configuring the VideoJet X40 SN You can start the Configuration Manager immediately after installation. 1. Double-click the icon on the desktop or s t art the program via the Start menu. After the program has started, the network is [...]

26 en | Installation VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems[...]

VideoJe t X40 SN Configuration Using a Web Brow ser | en 27 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 5 Configuration Using a W eb Brow ser 5.1 Connecting The integrated HTTP server in the VideoJet X40 SN provides you with the option to configure the unit over the network with a Web browser. Th is option is an a[...]

28 en | Configuration Using a Web Br owser VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems Establishing the Connection Before you can operate the VideoJet X 40 SN within your network, it must have a valid IP address for your network and a compatible subnet mask. The following default address is preset[...]

VideoJe t X40 SN Configuration Using a Web Brow ser | en 29 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 Protected VideoJet X40 SN If the VideoJet X40 SN is password protected ag ainst unauthorized access, the Web browser displays a corresponding message and prompt s you to enter the pa ssword when you attempt to a[...]

30 en | Configuration Using a Web Br owser VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems Starting Configuration X Click the SETTINGS link in the upper section of th e win dow. The Web browser opens a new page with the configuration menu. Navigation 1. Click one of the menu items in the left window m[...]

VideoJe t X40 SN Configuration Using a Web Brow ser | en 31 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 5.3 Basic Mode: Unit Access Device name You can give the VideoJet X40 SN a name to make it easier to identify. The name makes the task of administering multiple units in larger video monitori ng systems easier, [...]

32 en | Configuration Using a Web Br owser VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems Password A VideoJet X40 SN is generally protected by a password to prevent unau thorized acces s to the unit. You can use different auth orization levels to limit access. The VideoJet X40 SN opera tes with three[...]

VideoJe t X40 SN Configuration Using a Web Brow ser | en 33 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 Time server IP address The VideoJet X40 SN can receive the time s ignal from a time server using various time server protocols, and then use it to set the internal cl ock. The unit polls the time signal automati[...]

34 en | Configuration Using a Web Br owser VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems Gateway address If you want the unit to establish a connection to a remote location in a different subnet, enter the IP address of the gateway here. Otherwise leave the box blank ( 0.0.0.0 ). 5.6 Basic Mode: Enc[...]

VideoJe t X40 SN Configuration Using a Web Brow ser | en 35 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 5.7 Basic Mode: Audio You can set the gain of the audio signals to suit your specific requirements. The current video image is shown in the small window next to the slide controls to help you check the selected [...]

36 en | Configuration Using a Web Br owser VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 5.8 Basic Mode: Recording You can record the images from the cameras connected to the VideoJet X40 SN on various local storage media or on an appr opriately configured iSCSI system. CF cards (see Section CF Slot[...]

VideoJe t X40 SN Configuration Using a Web Brow ser | en 37 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 5.10 Advanced Mode: Identification Device ID Each VideoJet X40 SN should be assigned a uniq ue identifier that you can enter here as an additional means of identification. Device name You can give the VideoJet X[...]

38 en | Configuration Using a Web Br owser VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems You can use the second line for entering addition al characters; these can be selected from a table. 1. Click the icon next to the second line. A ne w window with the character map is opened. 2. Click the requir[...]

VideoJe t X40 SN Configuration Using a Web Brow ser | en 39 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 You can define and change a password for each authorization level if you are logged in as service or if the unit is not password protected. Enter the password for the approp riate authorization level here. Confi[...]

40 en | Configuration Using a Web Br owser VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 1. First check whether the correct time zone is selected. If it is not correct, select the appropriate time zone for the system, and click the Set button. 2. Click the Details button. A new window will open and [...]

VideoJe t X40 SN Configuration Using a Web Brow ser | en 41 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 Camera name st amping This field sets the position of the camera name overlay. It can be displayed at the Top , at the Bottom or at a position of your choice that you can then specify using the Custom option. Or[...]

42 en | Configuration Using a Web Br owser VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 5.14 Advanced Mode: Appearance On this page you can adapt the appearance of the web inte rface and change the website language to meet your requirements. If nec essary, you can replace the manufacturer' s l[...]

VideoJe t X40 SN Configuration Using a Web Brow ser | en 43 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 JPEG interval You can specify the interval at which the individual images should be generated for the M- JPEG image on the LIVEPAGE . JPEG quality You can specify the image quality for displaying M-JPEG on the L[...]

44 en | Configuration Using a Web Br owser VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems Show alarm inputs Alarm inputs are shown next to the video image as icons, along with their assigned names. If an alarm is active, the corr esponding icon changes color. Show relay outputs Relay outputs are show[...]

VideoJe t X40 SN Configuration Using a Web Brow ser | en 45 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 5.16 Advanced Mode: L ogging Save event log Check this option to save event messages in a text file on your local computer. You can then view, edit and print this file with any text editor or the s tandard Offic[...]

46 en | Configuration Using a Web Br owser VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 5.17 Advanced Mode: Video Input You can activate the 75 Ohm terminating re sistance for each video input of the VideoJet X40 SN. The terminating resistance must be deactivated for the video signal to be looped t[...]

VideoJe t X40 SN Configuration Using a Web Brow ser | en 47 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 5.18 Advanced Mode: Pictur e Se ttings You can set the video image of each camera to suit your requirements. The current video image is displayed in the small window next to the slide controls as confirmation. Y[...]

48 en | Configuration Using a Web Br owser VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 5.19 Advanced Mode: Encoder Pr ofile For the video signal encoding, you can select a code algorithm for each and two profiles for each encoder (video input), and you ca n change the presets for the prof iles. Yo[...]

VideoJe t X40 SN Configuration Using a Web Brow ser | en 49 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 Pre-programmed profiles are available, each giving priority to different perspectives. – Low bandwidth (CIF) High quality for low bandwidth connect ions, resolution 35 2 × 288/240 pixels – Low delay (2/3 D1[...]

50 en | Configuration Using a Web Br owser VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems Target data rate You can limit the data rate for the VideoJet X40 SN to optimize utilization of the bandwidth in your network. The target data rate should be set according to the desired picture quality for typi[...]

VideoJe t X40 SN Configuration Using a Web Brow ser | en 51 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 Video quality This setting allows you to adjust the image quality. The Auto option automatically adjusts to the optimum combination of movement and image definition (focus). Alternatively, you can use the slide [...]

52 en | Configuration Using a Web Br owser VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 5.20 Advanced Mode: Audio You can set the gain of the audio signals to suit your specific requirem ents. The current video image is shown in the small window next to th e slide controls to help you check the sel[...]

VideoJe t X40 SN Configuration Using a Web Brow ser | en 53 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 5.21 Advanced Mode: S torage Management You can record the images from the cameras connected to the VideoJet X 40 SN on various local storage media or on an appr opriately configured iSCSI system. CF cards (see [...]

54 en | Configuration Using a Web Br owser VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems Device manager If you activate the VRM option in this screen, the VRM Video Recording Manager will manage all recording and you will not be able to configure any further settings here. Recording media Select the[...]

VideoJe t X40 SN Configuration Using a Web Brow ser | en 55 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 5. Check the boxes for the Overwrite older recordings option to specify which older recordings can be overwritten once the av ailable memory capacity has been used. Recording 1 corresponds to Stream 1, Recording[...]

56 en | Configuration Using a Web Br owser VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 5.22 Advanced Mode: R emote Video Device You can allow a remote video device to use the VideoJet X40 SN storage media. This means you can record video images from a camera that does not have its own storage medi[...]

VideoJe t X40 SN Configuration Using a Web Brow ser | en 57 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 5.23 Advanced Mode: R ecording Profile s You can define up to ten different recording profiles. You will then use these recording profiles in the recording scheduler, where they are linked with the indi vidual d[...]

58 en | Configuration Using a Web Br owser VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 6. For each profile, click the Set button to save the settings in the unit. Standard recording Here you can select the mode for standard recordin gs. If you select Continuous , the recording proce eds contin uou[...]

VideoJe t X40 SN Configuration Using a Web Brow ser | en 59 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 Recording includes You can specify whether, in addition to vi deo data, audio data and metadata (for example alarms, VCA data and serial data) should also be recorded. Includ ing metadata could make subsequent s[...]

60 en | Configuration Using a Web Br owser VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 5.25 Advanced Mode: R ecording Scheduler The recording scheduler allows you to link th e created recording profiles with the days an d times at which the images of selected cameras ar e to be recorded in the eve[...]

VideoJe t X40 SN Configuration Using a Web Brow ser | en 61 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 Holidays You can define holidays that are not in the standard weekly sche dule on which recordings are to apply. This allows you to apply a schedule fo r Sundays to other days with dates that fall on varying wee[...]

62 en | Configuration Using a Web Br owser VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 5.26 Advanced Mode: R ecording Status Certain details on the recording status are di splayed here for info rmation purposes. You cannot change any of these settings.[...]

VideoJe t X40 SN Configuration Using a Web Brow ser | en 63 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 5.27 Advanced Mode: Alarm Connections You can select how the VideoJet X40 SN responds to an alarm. In the event of an alarm, the unit can automatically connect to a pre-defi ned IP address. You can enter up to t[...]

64 en | Configuration Using a Web Br owser VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems Destination password If the remote station is password protected, enter the password here. In this page, you can save a maximum of ten dest ination IP addresses and hence up to ten passwords for connecting to re[...]

VideoJe t X40 SN Configuration Using a Web Brow ser | en 65 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 SSL encryption The data for the connection, for example the password, can be securely transmitted with SSL encryption. If you have selected the On option, only encrypted ports ar e offered in the Remote port par[...]

66 en | Configuration Using a Web Br owser VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 5.28 Advanced Mode: V CA The VideoJet X40 SN contains an integrated vide o content analysis (VCA), which can detect and analyze changes in the signal on the basis of image processing. Such changes can be due to [...]

VideoJe t X40 SN Configuration Using a Web Brow ser | en 67 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 5.29 Advanced Mode: V CA Profiles You can configure two profiles with different VCA configuratio ns. You can save profiles on your computer's hard drive and lo ad saved profiles from there. This can be usef[...]

68 en | Configuration Using a Web Br owser VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 3. Click the Save... button to save the profile settings to another f ile. A new window is opened, in which you can specif y where you want to save the file and what name you want to save it under. 4. Click the [...]

VideoJe t X40 SN Configuration Using a Web Brow ser | en 69 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 Sensitivity (MOTION+ only) The basic sensitivity of the motion detector ca n be adjus ted for the environmental conditions to which the camera is subject. The sensor reacts to variations in the brig htness of th[...]

70 en | Configuration Using a Web Br owser VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems Global change You can set how large the global change in th e video image must be for an alarm to be triggered. This setting is independent of the sensor fields selected under Select Area . Set a high value if f[...]

VideoJe t X40 SN Configuration Using a Web Brow ser | en 71 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 3. Left-click the fields to be activate d. Activated fields are marked yellow. 4. If necessary, click Select All to select the entire video frame for monitoring. 5. Right-click any fields you wish to deactivate.[...]

72 en | Configuration Using a Web Br owser VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 1. Click the profile you want to link in the Time periods field. 2. Click in a field in the table, hold down the mouse button and drag th e cursor over all the periods to be assigned to the selected profile. 3. [...]

VideoJe t X40 SN Configuration Using a Web Brow ser | en 73 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 5.31 Advanced Mode: V CA Event T riggered This configuration allows you stip ulate that the video content anal ysis is only to be activated when triggered by an event. As long as no trigger is activated, the Sil[...]

74 en | Configuration Using a Web Br owser VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems Trigger active Select the VCA configuration here that is to be enabled via an active trigger. A green check mark to the right of the list field indicates that the trigger is active. Trigger inactive Select the V[...]

VideoJe t X40 SN Configuration Using a Web Brow ser | en 75 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 Name The name makes it easier to identify the alar m in extensive video monitoring systems, for example with the VIDOS and Bo sch Video Management System programs. Enter a uniqu e and clear name here. Threshold [...]

76 en | Configuration Using a Web Br owser VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems Mail server IP address Enter the IP address of a mail server that op erates on the SMTP standard (Simple Mail Transfer Protocol). Outgoing e-mails are sent to the mail server via the address you entered. Otherwi[...]

VideoJe t X40 SN Configuration Using a Web Brow ser | en 77 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 5.34 Advanced Mode: Alarm T ask Editor As an alternative to the alarm settings on the va rious alarm pages, you can enter your desired alarm functions in script form here. This will overwrite all settings and en[...]

78 en | Configuration Using a Web Br owser VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 5.35 Advanced Mode: Alarm Inputs You can configure the alarm inputs of the VideoJet X40 SN. Alarm input Select Active high if the alarm is to be triggered when the contact closes. Select Active low if the alarm [...]

VideoJe t X40 SN Configuration Using a Web Brow ser | en 79 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 Operating mode Select an operating mode for the relay. For example, if you want an alarm-activated la mp to stay on after the alarm ends, select Bistable . If you wish an alarm-activated siren to sound for ten s[...]

80 en | Configuration Using a Web Br owser VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 5.37 Advanced Mode: COM1 You can configure the serial interface paramete rs (ora nge terminal block) to meet your requirements. Serial port function Select a controllable unit from the list. If you wish to use t[...]

VideoJe t X40 SN Configuration Using a Web Brow ser | en 81 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 Interface mode Select the desired protocol for the serial interface. 5.38 Advanced Mode: Network The settings on this page are used to integrate the VideoJet X40 SN into an existing network. Some changes only ta[...]

82 en | Configuration Using a Web Br owser VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 2. Click the Set and Reboot button. The VideoJet X40 SN is rebooted and the changed settings are activated. Automatic IP assignment If a DHCP server is employed in the network for the dynamic assignment of IP ad[...]

VideoJe t X40 SN Configuration Using a Web Brow ser | en 83 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 You can activate and configure encryption of the media data (video, audio and metadata) on the Encryption page (see Section 5.42 Advanced Mo de: Encryption, page 88 ). RCP+ port 1756 To exchange connection data,[...]

84 en | Configuration Using a Web Br owser VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems Force registration now You can force the regis tration by transferring the IP address to the DynDNS server. Entries that change frequently are not prov ided in the Domain Name System. I t i s a g o o d i de a t [...]

VideoJe t X40 SN Configuration Using a Web Brow ser | en 85 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 enter one or two SNMP host addresses, SN MP traps are sen t automatically. Select Off to deactiv ate the SNMP function. 1. SNMP host address / 2. SNMP host ad dress If you wish to send SNMP traps automatically, [...]

86 en | Configuration Using a Web Br owser VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 5.40 Advanced Mode: Multicasting In addition to a 1:1 connectio n between an encoder and a single receiver (unicast), the VideoJet X40 SN can enable multiple receivers to receive the video signal from an encoder[...]

VideoJe t X40 SN Configuration Using a Web Brow ser | en 87 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 Multicast Address Enter a valid multicast address for each stream fr om the relevant encoder (video input) to be operated in multicast mode (duplication of the data streams in the network). With the setting 0.0.[...]

88 en | Configuration Using a Web Br owser VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems – Large 704 × 576/480 pixels (4CI F) File name You can select how file names will be created fo r the individual images that are transmitted. – Overwrite The same file name is always used and any existing f[...]

VideoJe t X40 SN Configuration Using a Web Brow ser | en 89 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 5.43 Advanced Mode: Maint enance Firmware The VideoJet X40 SN is des igned in such a wa y that its functions and parameters can be updated with firmware. To do th is, transfer the current firmware package to the[...]

90 en | Configuration Using a Web Br owser VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems Configuration You can save configuration data for the VideoJet X40 SN on a co mputer and then load saved configuration data from a computer to the unit. Upload 1. Enter the full path of the file to upload or cli[...]

VideoJe t X40 SN Configuration Using a Web Brow ser | en 91 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 5.44 Advanced Mode: L icenses You can enter the activation key to release additional fu nctions or software modules. 5.45 Advanced Mode: Sy stem Ov er view The data on this page are for information pu rposes onl[...]

92 en | Configuration Using a Web Br owser VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 5.46 F unction T est The VideoJet X40 SN o ffers a variety of configur ation options. You should therefore check that it is functioning correctly af ter installation and configuration. The function test is the o[...]

VideoJe t X40 SN Operation | en 93 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 6 Operation 6.1 Operation with Microsoft Internet Explorer A computer with Microsoft Intern et Explorer (version 6.0 or hi gher) can re ceive live images from the VideoJe t X40 SN, control came ras or other peripher als and replay store[...]

94 en | Operation VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems Establishing the Connection Before you can operate the VideoJet X 40 SN within your network, it must have a valid IP address for your network and a compatible subnet mask. The following default address is preset at the factory: 192.168.[...]

VideoJe t X40 SN Operation | en 95 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 6.2 The LIVEP AGE Once the connection is established , the Web browser displays the LIVEPAGE . It shows the live video image on the right of the browser window. Depending on the configuration, various text overlays may be visible on the[...]

96 en | Operation VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems View Control Control options for perip herals (for example a pa n/tilt head or dome camera) depend on the type of unit installed and on the configuration of the VideoJet X40 SN. If a controllable unit is configured and connected to the [...]

VideoJe t X40 SN Operation | en 97 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 System Log / Event Log The System Log field contains information about the operating status of the VideoJet X40 SN and the connection. You can s ave these messages automatically in a file (see Section 5.15 Advanced Mode : LI VEPAGE Func[...]

98 en | Operation VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 6.3 Sa ving Snapshots You can save individu al images from the video se quence currently sh own on the LIVEPAGE in JPEG format on your computer's hard drive. The icon for re cording single images is only visible if the unit is conf[...]

VideoJe t X40 SN Operation | en 99 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 6.5 Running Recording Program The hard drive icon below the camera images on the LIVEPAGE changes during an automatic recording. A moving graphic will appear to indicate a running recording. If no recording is taking place, a static ico[...]

100 en | Operation VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 6.6 The RECORDINGS Page The RECORDINGS page for playing back recorded vi deo sequences can be accessed from the LIVEPAGE and from the SETTINGS menu. The RECORDINGS link is only visible if a storage medium h as been selected (see Sectio[...]

VideoJe t X40 SN Operation | en 101 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 The time bar offers various options fo r navigation. Red bars indicate the points in time where al arms were triggered. Dr ag the green arrow to navigate to these points quickly. 1. You can change the time interval by clicking the zoom[...]

102 en | Operation VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems Trick Mode If you are using a mouse with a scroll wheel, yo u can view recordings frame by frame in trick mode. To do this, place the mouse cursor in the timeline below the timescale and turn the scroll wheel. Playback is automatically[...]

VideoJe t X40 SN Operation | en 103 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 6.8 Hardware Connections Betwe en V ideo Ser vers A VideoJet X40 SN with connected cameras to it can be used as a sender and a compatible MPEG-4 hardware decoder (such as the VIP XD) with a connected monitor as a receiver using an Ethe[...]

104 en | Operation VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems Connecting with a Terminal Program Various requirements must be met in orde r to operate with a terminal program (see Section 8.9 Communication with Terminal Program, page 116 ). 1. Start the terminal prog ram and enter the command 1 i[...]

VideoJe t X40 SN Operation | en 105 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 6.9 Operation Using Sof tware Decoders The VideoJet X40 SN video serve r combines wi th VIDOS to provide a high-performance system solution. VIDOS is a software package for operating, cont rolling and managing CCTV installations (such [...]

106 en | Operation VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems[...]

VideoJe t X40 SN Maintenance and Upgrades | en 107 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 7 Maintenance and Upgrades 7.1 T esting the Ne twork Connection You can use the ping command to check the connection between two IP addresses. This allows you to test whether a un it in the network is active. 1. Open the[...]

108 en | Maintenance and Upgrades VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 7.3 Repairs Ensure that all maintenance or repair work is carried out only by qualified personnel (electrical engineers or network technology sp ecialists). In case of doubt, contact your dealer's technical service [...]

VideoJe t X40 SN Appendix | en 109 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 8 Appendix 8.1 T roubleshoo ting If you are unable to resolve a malfunction, please contact your supplier or systems integrator, or go directly to Bosch Secu rity Systems Cust omer Service. You can view a range of information about your[...]

110 en | Appendix VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 8.2 G eneral Malfunctions Malfunction Possible causes Recommended solution No connection between the unit and terminal program. Incorrect cable connections. Check all cables, plugs, contacts, terminals and connections. The computer&apos[...]

VideoJe t X40 SN Appendix | en 111 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 The unit does not report an alarm. Alarm source is not selected. Select poss ible alarm sources on the Alarm Inputs configuration page. No alarm response specifie d. Specify the desired alarm response on the Alarm Connections configurat[...]

112 en | Appendix VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 8.3 Malfunctions with iSCSI Connections Malfunction Possible causes Recommended solution After connecting to the iSCSI destination, no LUNs are disp layed. Incorrect LUN mapping during iSCSI system c onfiguration. Check the iSCSI system[...]

VideoJe t X40 SN Appendix | en 113 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 8.4 LEDs The VideoJet X40 SN networ k video server has a number of LEDs on its front and rear p anels that show the operating status and can give indications of poss ible malfunctions: ETH LED Connect LED CF LED Does not light up: No ne[...]

114 en | Appendix VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 8.5 Processor L oad If the VideoJet X40 SN is accessed via the Web browser, you will see the processor load indicators in the top right of the wind ow next to the manufacturer's logo. You can obtain additional information to help y[...]

VideoJe t X40 SN Appendix | en 115 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 8.8 T er minal Block The terminal block has several contacts for: – 4 alarm inputs – 4 relay outputs – Serial data transmission Pin Assignment The pin assignment of the serial interface depends on the interface mode used (s ee Sec[...]

116 en | Appendix VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 8.9 Communication with T erminal Program Data Terminal If a VideoJet X40 SN cannot be found in the ne twork or the connection to the network is interrupted, you can connect a data terminal to the VideoJet X40 SN for initial setup and se[...]

VideoJe t X40 SN Appendix | en 117 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 Assigning an IP Address Before you can operate a VideoJ et X40 SN in your network you must first assign it an IP address that is vali d for your network. The following default address is preset at the factory: 192.1 68.0.1 1. Start a te[...]

118 en | Appendix VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 8.10 Copyright s The firmware 4.0 uses the fonts "Adobe-H elvetica-Bold-R-Normal--24-2 40-75-75-P-138- ISO10646-1" and "Adobe-Helvetica-Bold-R-No rmal--12-120-75-75-P-7 0-ISO10646-1" under the following copyright: Co[...]

VideoJe t X40 SN Specif icatio ns | en 119 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 9 Specifications 9.1 Unit Operating voltage 10 to 30 V DC, power supply via external unit Power consumption Approx. 19 W with full equipment LAN interface 1 × Ethernet 10/100 Base-T, automatic adjustment, half/full duplex, RJ45[...]

120 en | Specifications VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems 9.2 Prot ocols/Standar ds 9.3 Image Refr esh Rat e Video standards PAL, NTSC Video coding protocols H.264 Basel ine Profile, MPEG-4, M-JPEG, JPEG Video data rate 9.6 kbps to 6 Mbps Image resolutions (PAL/NTSC) 704 × 576/480 pixel[...]

VideoJe t X40 SN Glossar y | en 121 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 10 Glossar y Symbols 10/100/1000 Base-T IEEE-802.3 specification for 10, 100 or 1000 Mbps Ethernet 802.1x The IEEE 802.1x standard provides a general method for authentication and authorization in IEEE-802 networks. Authentication is c[...]

122 en | Glossar y VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems H HTTP Hypertext Transfer Protocol: p rotocol for transmitting data over a network HTTPS Hypertext Transf er Protocol Secure: encryp ts and authenticates communication between Web server and browser I ICMP Internet Control Message Prot[...]

VideoJe t X40 SN Glossar y | en 123 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 MPEG-4 A further d evelopment of MP EG-2 designed for tr ansmitting audiovisual data at very low transfer rates (for example over the Internet) MSS Maximum Segment Size; maximum byte fi gure for the user data in a data packet N Net mas[...]

124 en | Glossar y VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems SNTP Simple Network Time Protocol ; a simplified version of NTP ( see NTP) SSL Secure Sockets Layer; an encryption protoc ol for data transmission in IP-based networks Subnet mask See Net mask T TCP Transmission Control Protocol Telnet[...]

VideoJe t X40 SN Index | en 125 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 11 Inde x A Activating the recording 61 Activation key 91 Alarm 17 , 41 , 96 Alarm e-mail 75 Alarm input 21 Alarm inputs 78 Alarm message 41 Alarm script 73 Alarm sensors 58 Audio connections 16 , 20 Audio input 16 Audio output 16 Audio se[...]

126 en | Index VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems M Main functions 15 Maintenance 9 Manufacturer logo 42 Media-replay 100 Milliseconds 41 Motion detector 66 Motion detector defaults 66 , 67 Motion detector object size 69 Motion detector sensitivity 69 MPEG ActiveX 27 , 93 , 102 MTU value [...]

VideoJe t X40 SN Index | en 127 Bosch Security Syst ems Installation and Operating Manual DOC | V4.0 | 2009.06 Transmission parameters 116 Transmission protocol 64 , 82 Transmission rate 80 Transmission standards 21 , 114 Transparent 80 Traps 85 Trick mod e 102 Trigger 21 Trigger relay 79 TTL 87 U UDP 64 , 82 Unicast 86 Unit date 39 Unit identifica[...]

128 en | Index VideoJe t X40 SN DOC | V4.0 | 2009.06 Installation and Operating Manual Bosch Security Syst ems[...]

[...]

Bosch Sicherheitssysteme GmbH Robert-Koch-Straße 100 85521 Ottobrunn Germany Telefon 089 6290-0 Fax 089 6290-1020 www.boschsecurity.com © Bosch Sicherheitssysteme GmbH, 2009[...]