Bosch INTELLIVOX DDC LBC 325X manual

I NTE LLIV O X D D C Installat ion Manual EN Active Line Array Loudspeakers LBC 325x Series[...]

Disclaimer 1 . The information in this manual has been carefully chec ked for accuracy, but no guarantee is given as to the correctness. 2. The information in this manual is subject to change without notice, and does not represent a commitment on the part of the vendor . Bosc h Security S ystems shall not be liable for any loss or damage whatsoever[...]

Figure and T able lists . Fig 1 LBC 32 53 /00 Intellivox-2c shown without front grill. . . . . . . . . . . . . . . . . . . . . . . . .5 Fig 2 W AGO massive to stranded wire clamp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Fig 3 Intellivox connector block. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[...]

Intellivox DDC | Installation Manual | Introduction Bosch Security Systems | July 2003 EN | 5 1 . Int roduct ion. This paper describes the factory recommended installation procedure for the Bosch Security Systems’ Intellivox range of controlled loudspeaker-arrays. This type of loudspeaker-array is equipped with an on- board Digital Signal Process[...]

2. Inst allation guide This chapter deals with the practical aspects of installing the Intellivox loudspeaker column. • S I units are used as a default, all mentioned dimensions are stated in meters or millimeters. • Unless stated otherwise, column dimensions refer to the standard Intellivox-2c, whic h has the electronics module mounted at the [...]

A simple surveillance function may be realized by means of the ‘failure detect’ connection in case the R S- 48 5 network interface is not used. Three relay contacts, ‘normally open’ (N O), ‘normally closed’ (NC ) and ‘common’ ( CO M) are available on this connector . If the autogain function of the Intellivox is used, a separate amb[...]

2.3 W iring and connect ions. 2.3. 1 Mains power . • Be sure that the mains voltage stated on the unit complies with the local standard before connecting the Intellivox to the mains supply . The maximum power consumption of the Intellivox-2c model is 45 0 V A, this figure however is different from other models (refer to the appropriate datasheet [...]

Fig 3 Intellivo x connector block . • A removable panel on the front side of the Intellivox (backside for the Intellivox-1b) allows all connectors to be inserted when the unit is already mounted. Proceed as follows to fit a W AG O 23 1 connector: 1 . Prepare the cable, about 8 - 9 mm (around 0.3 5”) of the individual wire insulation should be r[...]

Fig 4 W AGO 23 1 cross-section Fig 5 C onnecting a WA GO 23 1 T able 2 PVC insert sizes. 2.5 Methods for mounting the Intellivox . 2.5. 1 General. F or mounting of the Intellivox column there are two or three attachment points (depending on the model) eac h consisting of four threaded inserts at the rear of the enclosure. One point is located at th[...]

hexagonal nut. The swivel brackets are mounted to the rear of the enclosure by four M5 pan head screws (factory supplied). Refer to T able 4 in chapter 3. 1 for ordering information. 3. The third method is to mount the column directly to a wall or a dedicated mounting panel by means of spacers and screws through the mounting surface. In this case e[...]

columns can differ substantially from the 2c model. Mec hanical drawings of the other models can be found in chapter 3.5 or in the respected datasheet. Fig 7 - The LBC 325 3/00 dimensions are shown, including the vertical spacing between the upper and the lower bracket as well as the vertical offset of the acoustical reference. 2.5.3 Mounting proce[...]

3. Appendix . 3. 1 Reference part list . Connectors for ext ernal wiring . T able 3 Intellivox ex ternal connectors det ails. Other installat ion related accessories. T able 4 Specific installation related accessories. Other network related accessories. T able 5 Specific netw ork related accessories 3.2 Grounding strat egy . The ground (G N D) term[...]

The AG N D pin serves as a reference for the S PL and temperature measuring input circuitry . T o keep this ground signal as clean as possible, the AG N D wires together with the M I C and the NT C signal should be run through a shielded cable. The shield should be connected to the G N D pin of this terminal block. • AG ND should not be connected[...]

Although in terms of safety and immunity this is the most preferable set up, an unwanted ground loop is created which can cause audible noise or hum. The appearance of this effect is strongly depending on the cable routing, the design of the grounding scheme and the existence of local magnetic fields (caused by power transformers, railway chopper s[...]

In order to restore the galvanic safety path of the signal wiring up to a certain level, it is possible to connect a 1 00 OH M S 1W resistor parallel with the 1 00nF capacitor . The isolation of the low frequency ground loop is partly canceled by this resistor, but the reduction of the induced noise can still be sufficient while at the same time so[...]

Fig 1 3 Optional high frequency decoupling for 70 V / 1 00 V systems . Conclusion: Because the Intellivox can be a part of a complex installation it is impossible to prescribe a fixed grounding strategy that will perform best in all situations. Safety, immunity and reduction of emission are very important issues that should always determine the gro[...]

Network configuration . A network is composed of one master device and one or more slave devices. A master device can exist of a P C running the R S-48 5 network W inControl software and a R S-23 2 to RS- 485 converter . All slave devices are wired in parallel, the master device is connected with the AB and YZ terminals interchanged (see Fig 1 4). [...]

Master device As mentioned before the RS- 485 network concept needs one master device. This master device ( network controller) is composed of a P C running W inControl and a R S-23 2 to RS- 485 adapter connected to the RS- 23 2 port of the P C. D etailed information about the W inControl program can be found in the related help file. The R S-232 t[...]

N otes for type RS- 232 to RS-4 85 adapter: • Both ends of the RS-2 32 to R S-48 5 connector have the same 9p female sub-d connector . Be careful to install it in the proper way . • The +9 V ( pin 9) at the R S-23 2 side of the adapter should be connected to an external + 9 V / 50 mA D C power supply in case the power delivered by the P C (R TS[...]

Fig 1 7 Wiring configuration using R S-485 net work cable type. Ambient S PL and t emperature sensor connections . Figure 18 and 1 9 show the wiring configurations for the sensor with the two cable types. Fig 1 8 Wiring configuration at the sensor using asymmetrical cable type Fig 1 9 Wiring configuration at the sensor using RS- 485 net work cable [...]

3.5 Intellivox dimensions of t he different models. Fig 20 LBC 325 1 /00 Intellivo x-1b dimensions, all measures in mm. Intellivox DDC | Installation Manual | Appendix Bosch Security Systems | July 2003 EN | 22[...]

Fig 2 1 LBC 3252/00 Intellivo x-2b dimensions, all measures in mm Intellivox DDC | Installation Manual | Appendix Bosch Security Systems | July 2003 EN | 23[...]

Fig 22 LBC 3252/ 1 0 Intellivo x-2b dimensions, all measures in mm Intellivox DDC | Installation Manual | Appendix Bosch Security Systems | July 2003 EN | 24[...]

Fig 23 LBC 3 253 /00 Intellivox-2c dimensions, all measures in mm Intellivox DDC | Installation Manual | Appendix Bosch Security Systems | July 2003 EN | 25[...]

Fig 24 LBC 325 3/ 1 0 Intellivox-2c dimensions, all measures in mm Intellivox DDC | Installation Manual | Appendix Bosch Security Systems | July 2003 EN | 26[...]

Fig 25 LBC 3254/00 Intellivo x -4c dimensions, all measures in mm. Intellivox DDC | Installation Manual | Appendix Bosch Security Systems | July 2003 EN | 27[...]

Fig 26 LBC 3254/ 1 0 Intellivo x-4c dimensions, all measures in mm. Intellivox DDC | Installation Manual | Appendix Bosch Security Systems | July 2003 EN | 28[...]

Fig 27 LBC 3256/00 Intellivo x-6c dimensions, all measures in mm Intellivox DDC | Installation Manual | Appendix Bosch Security Systems | July 2003 EN | 29[...]

Fig 28 LBC 3256/ 1 0 Intellivo x-6c dimensions, all measures in mm Intellivox DDC | Installation Manual | Appendix Bosch Security Systems | July 2003 EN | 30[...]

© 2003 Bosch Security Systems GmbH 9922 1 4 1 505 1 1en Robert B osc h GmbH Geschäftsbereic h Postfac h 1 0 60 50 70049 Stuttgart T elefax (0 7 1 1 ) 8 1 1-1 2 34 www .bosch.de/k Bosch Security Systems B.V . P .O. Box 80002 5600 JB Eindhoven The Netherlands T ele +3 1 40 27 80000 www .boschsecuritysystems.com[...]