Brother S-7200B manual

S-7200B SINGLE NEEDLE DIRECT DRIVE STRAIGHT LOCK STITCHER WITH THREAD TRIMMER Please read this manual before using the machine. Please keep this manual within easy reach for quick reference. This basic operation manual describes basic operations including sewing machine operations. For cleaning, standard adjustment s and more det ails, please refer[...]

S-7200B Thank you very much for buying a BROTHER sewing machine. Before using your new machine, please read the safety instructions and the explanations given in the instruction manual. With industrial sewing machines, it is normal to carry out work whil e positioned directly in front of moving parts such as the needle and thread take-up, and conse[...]

S-7200B i SAFETY INSTRUCTIONS [1] Safety indications and their meanings This instruction manual and the indications and symbols that are used on the ma chine itself are provided in order to ensure safe operation of this machine and to prevent accidents and injury to yourself or other people. The meanings of these indications and symbols are given b[...]

S-7200B ii [2] Notes on safety DANGER Wait at least 5 minutes after turning off the power switch and disconnecting the power cord from the wall outlet before opening the face plate of the control box. Touching areas where high voltages are present can result in severe injury. CAUTION Environmental requirements Use the sewing machine in an area whic[...]

S-7200B iii CAUTION Sewing This sewing machine should only be used by operators who have receiv ed the necessary training in safe use beforehand. The sewing machine should not be used for any applications other than sewing. Be sure to wear protective goggles when using the machine. If goggles are not worn, there is the danger that if a needle break[...]

S-7200B iv [3] Warning labels The following warning labels appear on the sewing machine. Please follow the instructions on the labels at all times when using the machine. If the la bels have been removed or are difficult to read, please contact your nearest Brother dealer. 1 2 3 Be sure to connect the ground. If the ground connection is not secure,[...]

S-7200B CONTENTS 1. CONVENIENT FUNCTION FOR SMOOTH SEWING ............................... 1 2. NAMES OF MAJOR PARTS ................ 2 3. INSTALLATION .................................... 3 3-1. Table proce ssing diagram ................................ 4 3-2. Installation ........................................................ 4 3-3. Lubrication [...]

S-7200B 1. CONVENIENT FUNCTION FOR SMOOTH SEWING 1 1. CONVENIENT FUNCTION FOR SMOOTH SEWING Lower thread counter Notification given when greasing is required INSTRUCTION MANUAL CD 5-7. Using the lower thread counter INSTRUCTION MANUAL CD 11-2. Applying grease The graphic display lights and a buzzer sounds before the bobbin thread runs out, so that [...]

S-7200B 2. NAMES OF MAJOR PARTS 2 2. NAMES OF MAJOR P ARTS (1) Bobbin winder (2) Thread wiper (-4[][] specifications) (3) Lifting lever (4) Quick reverse (Actuator) (5) Presser foot (6) Control box (7) Control box panel (8) Knee lifter assembly (9) Power switch (10) Oil gauge window (-[]0[], []3[] specifications) (11) Reverse lever (12) Stitch leng[...]

S-7200B 3. INSTALLATION 3 3. INST ALLA TION CAUTION Machine installation should only be carried out by a qualified technician. Contact your Brother dealer or a qualified electrician for any electrical work that may need to be done. The sewing machine weighs more than 44 kg. The installation should be carried out by two or more people. Do not connec[...]

S-7200B 3. INSTALLATION 4 3-1. Table processing diagram  The top of the table should be 40 mm in thickness and should be strong enough to hold the weight and with-stand the vibration of the sewing machine.  Drill holes as indicated in the illustration below. 3-2. Installation 1 . Control box (1) Control box (2) Bolts [3 pcs] (3) Nuts [3 pcs] [...]

S-7200B 3. INSTALLATION 5 3 . Power switch (1) Power switch (2) Screws [2 pcs] 4 . Oil pan (1) Head cushions (left) [2 pcs] (2) Head cushions (right) [2 pcs] (3) Oil pan 5 . Rubber cushions (1) Rubber cushions [2 pcs] (2) Nails [4 pcs] 6 . Knee lifter complying bar (3) Knee lifter complying bar 2092M Operato r 2094M 3632M[...]

S-7200B 3. INSTALLATION 6 7 . Machine head (1) Hinges [2 pcs] (2) Machine head (3) Head rest NOTE: Tap the head rest (3) securely into the table hole. If the head rest (3) is not pushed in as far as it will go, the machine head will not be sufficiently stable when it is tilted back. 8 . Operation panel (Models with operation panel) (1) Operation pa[...]

S-7200B 3. INSTALLATION 7 1 1 . Knee lifter plate (1) Knee lifter plate (2) Bolt * Loosen the bolt (3) and move the knee lifter plate (1) to a position where it is easy to use. <Knee lifter adjustment> 1. Turn the machine pulley so that the feed dog is below the top of the needle plate. 2. Lower the presser foot (5) by using the lifting lever[...]

S-7200B 3. INSTALLATION 8 3-3. Lubrication (-[]0[],[]3[] specifications) * If the sewing machine is -[]5 [] specifications, it is a complete dry type machine, and so no lubrication is necessary. CAUTION Do not connect the power cord until lubrication has been completed, otherwise the machine may operate if the treadle is depressed by mistake, which[...]

S-7200B 3. INSTALLATION 9 3-4. Connecting the cords DANGER Wait at least 5 minutes after turning off the power switch and disconnecting the power cord from the wall outlet before opening the face plate of the control box. Touching areas where hi gh voltages are present can result in severe injury. CAUTION Contact your Brother dealer or a qualified [...]

S-7200B 3. INSTALLATION 10 (1) 7-pin head detector unit connector (2) 10-pin operating panel connector (Models with operation panel) (3) 14-pin encoder connector (4) 14-pin machine connector Refer to the following page for the 4-pin motor connector. 2. Binding the cords (1) Repeat cable tie (2) Wire clip NOTE:  Bind the cords in such a way that [...]

S-7200B 3. INSTALLATION 11 3 . Other cords (1) 6-pin power supply connector (2) 4-pin motor connector (3) Wire clip (4) Power cord <For single-phase specifications> Insert the power cord plug (5) into a wall outlet. <For three-phase specifications> 1. Attach an appropriate plug to the power cord (4). (The green and yellow wire is the gr[...]

S-7200B 3. INSTALLATION 12 3-5. Test operation (Operating the treadle) CAUTION Do not touch any of the moving parts or press any objects against the machine while sewing, as this may result in personal injury or damage to the machine. 1. Turning on the power <Models with operation panel> Press the ON power switch (1). The power indicators (2)[...]

S-7200B 4. PREPARATION BEFORE SEWING 13 4. PREP ARA TION BEFORE SEWING 4-1. Installing the needle CAUTION Turn off the power switch before installing the needle. The machine may operate if the treadle is depressed by mistake, which could result in injury. 1. Turn the machine pulley to move the needle bar to its highest position. 2. Loosen the screw[...]

S-7200B 4. PREPARATION BEFORE SEWING 14 2126M 4-3. Winding the lower thread CAUTION Do not touch any of the movi ng parts or press any objects against the machine while winding the lower thread, as this may result in personal injury or damage to the machine. 1. Turn on the power switch. 2. Place the bobbin (1) onto the bobbin winder shaft (2). 3. W[...]

S-7200B 4. PREPARATION BEFORE SEWING 15 4-5. Threading the upper thread CAUTION Turn off the power switch before threading the upper thread. The machine may operate if the treadle is depressed by mistake, which could result in injury. Turn the machine pulley and raise the thread take-up (1) before threading the upper thread. This will make threadin[...]

S-7200B 5. USING THE OPERATION PANEL (BASIC OPERATIONS) 16 5. USING THE OPERA TION P ANEL (BASIC OPERA TIONS) 5-1. Names and functions • The operation panel keys cannot be operated while sewing is in progress. Select the keys and set the number of stitches before starting sewing. • In the case of keys with indicators, the in dicator illuminates[...]

S-7200B 5. USING THE OPERATION PANEL (BASIC OPERATIONS) 17 (6) Fixed stitch key When this key is pressed so t hat the indicator illuminates, t he number of stitches (1-1999) in the E stitch number display is sewn, and then the sewing machine stops automatically. (7) Name label key When this key is pressed so that the indicator illuminates, fixed st[...]

S-7200B 5. USING THE OPERATION PANEL (BASIC OPERATIONS) 18 5-2. Sewing start and end backtack stitches 1 Setting start backtack stitches 2 Setting end backtack stitches 3 Start backtacking is carried out. After it has finished, normal sewing continues for as long as the treadle remains depressed. NOTE: If the treadle is returned to the neutral posi[...]

S-7200B 6. SEWING 19 6. SEWING CAUTION Attach all safety devices before usi ng the sewing machine. If the machine is used without these devices attached, injury may result. Turn off the power switch at the following times. The machine may operate if the treadle is depressed by mistake, which could result in injury.  When threading the needle [...]

S-7200B MEMO 20[...]

For cleaning, standard adjustments and more details, please refer to the instruction manual contained in the Document CD. Contents of the Document CD The following documents are contained in PDF format. ・ Basic Operation Manual ・ Instruction Manual ・ Parts Book How to use the Document CD Refer to “Using Document CD” which comes with the D[...]