Buhler FK369 manual

[...]

[...]

Heavy Duty Finishing Mower TABLE OF CONTENTS DESCRIPTION PAGE WARRANTY ................................................................ 1 INTRODUCTION ......................................................... 2 SAFETY ....................................................................... 3 Safety ...................................................[...]

Heavy Duty Finishing Mower PARTS DRAWINGS .................................................... 24 5’, 6’ & 7’ Rear Discharge Drawing ......................... 24 5’ 6’ & 7’ Rear Discharge Parts List ....................... 25 Gearbox Drawing.................................................... 28 Gearbox Parts List ..............[...]

Heavy Duty Finishing Mower 1 WARRANTY POLICY Buhler Manufacturing products are warranted for a period of twelve (12) months (90 days for commercial application) from original date of purchase, by original purchaser, to be free from defects in material and workmanship under correct, normal agricultural use and proper applications. Buhler Manufacturi[...]

Heavy Duty Finishing Mower 2 INTRODUCTION Buhler has been building top quality finishing mowers for 15 years and has refined these mowers to be among the best in the industry. Manufactured with top quality material, the edge of the mower deck features solid reinforcing rods. The Heavy Duty Finishing Mowers are Buhler Quick Hitch compatible and are [...]

Heavy Duty Finishing Mower 3 SAFETY Remember, YOU are the key to safety. Good safety practices not only protect you, but also the people around you. Make these practices a working part of your safety program. Be certain that everyone operating this equipment is familiar with the recommended operating and maintenance procedures and follows all the s[...]

Heavy Duty Finishing Mower 4 GENERAL SAFETY INSTRUCTIONS Have a first-aid kit available for use and know how to use it. Have a fire extinguisher available, stored in a highly visible location, and know how to use it. Wear appropriate protective gear. This list may include but is not limited to: - Hard hat - Protective shoes with slip resistant sole[...]

Heavy Duty Finishing Mower 5 TRANSPORT SAFETY Review Transport Safety instructions in tractor manual before moving. Check with local authorities regarding transport on public roads. Obey all applicable laws and regulations. Make sure the SMV (Slow Moving Vehicle) emblem and all the lights and reflectors that are required by the local highway and tr[...]

Heavy Duty Finishing Mower 6 HEAVY DUTY FINISHING MOWER SAFETY SIGNS #1 #2 #3[...]

Heavy Duty Finishing Mower 7 SAFETY SIGNS – cont’d. #4 # 5 #6 #7 Replace safety sign immediately should it become damaged, torn or illegible. Obtain replacements from your authorized dealer using the part numbers shown.[...]

Heavy Duty Finishing Mower 8 HITCH ASSEMBLY INSTRUCTIONS 1. The hitch is assembled except for the two pivot bars (#69). Bolt one end of each pivot bar between the welded brackets at the back of the deck using the bolts assembled in the mower. 2. Remove the 3/4” bolt (#63) at the top of the hitch assembly. Using the same bolt, assemble with the pi[...]

Heavy Duty Finishing Mower 9 START-UP 1. Park the unit on hard level ground with the mower slightly raised. 2. Adjust the sway blocks or chains on the tractor so the mower is centered between the rear wheels. 3. Adjust the three-point hitch arms to level the mower side to side. 4. Adjust the turnbuckle on the top of the three-point hitch arms to le[...]

Heavy Duty Finishing Mower 10 OPERATING INSTRUCTIONS The Heavy Duty Finishing Mower is designed to be used on a tractor with a standard category 1 three-point hitch. See the specification sheet for horsepower requirements. Using excessive power will shorten the life of the drive train components. CONNECTING TO TRACTOR: Park the mower and tractor on[...]

Heavy Duty Finishing Mower 11 FIELD OPERATION 1. The mower works best on dry grass. Slower cutting speed and occasional cleaning may be required on damp or wet grass. 2. The PTO must run at the full 540 rpm for a good cut. Slower speeds or double cutting could be required for very high grass. 3. Use a higher blade setting for rough areas to prevent[...]

Heavy Duty Finishing Mower 12 THEORY OF OPERATION[...]

Heavy Duty Finishing Mower 13 MAINTENANCE HEAVY DUTY FINISHING MOWER PTO SHAFTS MAINTENANCE: The cross journals and the shield bearings at both ends of the shaft should be greased every 8 hours. Use 1 or 2 pumps of high temperature grease. The cones on the outer PTO shield must be turned until the access holes line up with the grease nipple in the [...]

Heavy Duty Finishing Mower 14 PTO SHAFT[...]

Heavy Duty Finishing Mower 15 MOWER DECK WHEEL BEARINGS The mower wheel bearings are packed in grease when they are shipped. They should be repacked in fresh grease once a year or every 200 hours of usage. MOWER DECK WHEEL BEARINGS ITEM PART# DESCRIPTION 1 902422 Wheel Yoke 2 902489 1'' x 9 1/4'' long Wheel Yoke Pin 3 812681 3/1[...]

Heavy Duty Finishing Mower 16 MOWER GEARBOX LUBRICATION The gearbox should be filled with SAE90 oil to the bottom of the level plug when shipped. Check the mower gearbox before using and at regular intervals (approximately every 40 hours). See that the oil level is maintained. On the mower gearbox the vent plug also acts as the fill plug. MOWER SPI[...]

Heavy Duty Finishing Mower 17 SPINDLE REPLACEMENT OUTER SPINDLES : remove the belt guard on the side required (#7 & #8). Loosen the belts by first loosening the bolts holding the gearbox base plate (#2). Turn the 5/8” hex nut (#3) on the threaded rod on the base plate until there is enough slack in the belt to slip it off the spindle pulley. [...]

Heavy Duty Finishing Mower 18 HEAVY DUTY MAINTENANCE – SPINDLE REPLACEMENT[...]

Heavy Duty Finishing Mower 19 SPINDLE REPLACEMENT ITEM PART# DESCRIPTION 1 912300158 Gearbox Assembly 2 980004200 Gearbox Base Plate 3 81676 5/8'' Hex Nut (pl) 4 84217 3/8'' Wing Nut (pl) 5 84000 3/8'' BS Flat Washer (pl) 6 906343 Gearbox Mount Plate 7 906353 5' R.H. Belt Guard 906355 6' R.H. Belt Guard 90226[...]

Heavy Duty Finishing Mower 20 BLADE REPLACEMENT The mower deck must be securely blocked up or locked in place before doing a blade replacement. When replacing or grinding blades, all three blades must be replaced or reground at the same time to maintain the proper balance in the cutting unit. Use heavy leather gloves to handle the blades. It is eas[...]

Heavy Duty Finishing Mower 21 BLADE REPLACMENT ITEM PART# DESCRIPTION 1 902667 5' Rear Discharge Deck 902668 6' Rear Discharge Deck 902669 7' Rear Discharge Deck 2 81593 3/8'' Lock Washer (pl) 3 81592 3/8'' Hex Nut (pl) 4 86171 3/8'' x 1 1/4'' Hex Bolt (pl) 5 912301558 Snap Ring 6 966860 Spindl[...]

Heavy Duty Finishing Mower 22 SERVICE NOTES A basic requirement for a steady top performance of the machine is proper and regular maintenance. Use only original BUHLER parts. Keep the machine in a functioning and efficient condition by completing the maintenance and lubrication work as listed in the maintenance checklist. If maintenance is due, no [...]

Heavy Duty Finishing Mower 23 CHECKING BOLT TORQUE The tables shown below give correct torque values for various bolts and hex bolts. Tighten all bolts to the torques specified in chart unless otherwise noted. Check tightness of bolts periodically, using bolt torque chart as a guide. Replace hardware with the same strength bolt. NOTE: See page 16 f[...]

Heavy Duty Finishing Mower 24 5’, 6’ & 7’ HEAVY DUTY REAR DISCHARGE FINISHING MOWER[...]

Heavy Duty Finishing Mower 25 WHEN ORDERING PARTS Always give your dealer the Model, Color and Serial Number of your machine to assist him in ordering and obtaining the correct parts. Use the exploded view and tabular listing of the area of interest to exactly identify the required part. 5', 6', & 7' HEAVY DUTY REAR DISCHARGE FIN[...]

Heavy Duty Finishing Mower 26 25 811646 1/2" x 6" Hex Bolt (pl) 26 81637 1/2" Lock Washer (pl) 27 81636 1/2" Hex Nut (pl) 28 812769 1 1/2" O.D. x 9/16" I.D . x 10ga Washer (pl) 29 84270 5/8" x 1 3/4" Hex Bolt (pl) 30 81677 5/8" Lock Washer (pl) 31 81676 5/8" Hex Nut (pl) 32 84346 3/4" x 2 1/2&q[...]

Heavy Duty Finishing Mower 27 65 966188 2 1/2" O.D. x 21/32" I.D. Washer (Supplied with Spindle) 66 966189 5/8" x 1 1/4" Grade 8 Hex Bolt Lock (Supplied with Spindle) 67 966190 5/8" Lock Washer (pl) Extra Heavy (Supplied with Spindle) 68 966195 15/600 x 6" Tire with Wheel 69 966760 Pivot Bar 40" long (5') 966[...]

Heavy Duty Finishing Mower 28 HEAVY DUTY FINISHING MOWER GEARBOX[...]

Heavy Duty Finishing Mower 29 HEAVY DUTY FINISHING MOWER GEARBOX PARTS LIST Item # Part # Description 912300158 Gearbox Complete 1 966813 Housing 2 914015 Output Cap 3 966814 Blank Cap 4 966815 Input Gear, 29T 5 966816 Pinion Gear, 15T 6 966817 Input Shaft 7 966542 Ball Bearing, 6207 8 966555 Ball Bearing, 6208 9 966818 Input Seal 10 966819 Output [...]

Heavy Duty Finishing Mower 30 HEAVY DUTY FINISHING MOWER SPINDLE ASSEMBLY[...]

Heavy Duty Finishing Mower 31 FINISHING MOWER SPINDLE PARTS LIST (4', 5' & 6' SIDE AND REAR) Item # Part # Description 906339 Spindle Assembly Complete (Includes Hardware) 1 966764 Spindle Housing 2 906399 Spindle Bearing, 6206-Z 3 912301558 Snap Ring 4 906394 Spindle Shaft 5 966769 Snap Ring 6 966820 Shield 7 966821 Blade Mount [...]

Heavy Duty Finishing Mower 32 HEAVY DUTY REAR DISCHARGE FINISHING MOWER PTO SHAFT[...]

Heavy Duty Finishing Mower 33 HEAVY DUTY REAR DISCHARGE FINISHING MOWER PTO SHAFT PARTS LIST Item # Part # Description F0401 Shaft Complete - 5' & 6' F0400 Shaft Complete - 7' 1 907290 Yoke 2 920-002 Repair Kit 3 920-004 Outer Tube Yoke 4 920-006 Flexible Pin 5 936404 Outer Cardan Tube - 5' & 6' 936403 Outer Cardan [...]

Heavy Duty Finishing Mower 34 Heavy Duty Rear Discharge Finishing Mower Chain Kit Item # Part # Description 1 902667 5' Deck Weldment 902668 6' Deck Weldment 902669 7' Deck Weldment 2 902820 62 1/4'' Chain Guard Plate (5') 902823 74 1/4'' Chain Guard Plate (6') 902825 86 1/4'' Chain Guard Plate[...]

Heavy Duty Finishing Mower 35 HEAVY DUTY REAR DISCHARGE CHAIN KIT[...]

Heavy Duty Finishing Mower 36 QUICK HITCH KIT[...]

Heavy Duty Finishing Mower 37 BLADE HEIGHT ADJUSTMENT The mowers must be raised off the ground far enough to pull the wheel yoke (#5) out of the welded sleeves at the ends of the axles (#1). Be sure the tractor is turned off. Pull out the clip (#4) and remove the wheel yoke. There are ½” and 1” spacers to adjust the cutting height. The cutting[...]

Heavy Duty Finishing Mower 38 MOWER DECK BELT ADJUSTMENT[...]

Heavy Duty Finishing Mower 39 MOWER DECK BELT ADJUSTMENT Start by removing both belt guards on the mower deck. Loosen the bolts holding the gearbox base plate (#7). Turn the 5/8” hex nuts (#6) on the threaded rod on the base plate until there is enough slack in the belts to slip them off the spindle pulleys. If the belts can be pulled off by slid[...]

Heavy Duty Finishing Mower 40 SHIPPING KIT AND BUNDLE NUMBERS The following is a lit of Kit Numbers for this product and the Bundle Numbers, Descriptions, and Quantities for each Kit. QUANTITY BUNDLE NO. DESCRIPTION Y550RHD 60” HEAVY DUTY FINISHING MOWER 1 F0688 5’ Mower 1 F0670 Tires 1 F6670 Chain Kit 1 F6673 Carton Y650RHD 72” HEAVY DUTY FI[...]

NOTES[...]

NOTES[...]

[...]

DIVISION LOCATIONS U.S. WAREHOUSES Farm King Division 301 Mountain Street S. Morden, MB R6M 1X7 Ph.: (204) 822-4467 Fax: (204) 822-6348 Allied/Inland Division 1260 Clarence Avenue Winnipeg, MB R3T 1T2 Ph.: (204) 284-6100 Fax: (204) 477-2325 B.I.I. Division 1330 43 rd Street N.W. Fargo, ND 58102 Ph: (701) 282-7014 Fax: (701) 282-5865 B.C., Abbotsfor[...]