Bunn ULTRA-1 manual

UL TRA-1 UL TRA-2 INST ALLA TION & OPERA TING GUIDE BUNN-O-MA TIC CORPORA TION POST OFFICE BOX 3227 SPRINGFIELD, ILLINOIS 62708-3227 PHONE: (217) 529-6601 F AX: (217) 529-6644 T o ensure you have the latest revision of the Operating Manual, or to view the Illustrated Parts Catalog, Programming Manual, or Service Manual, please visit the Bunn-O-[...]

2 40563 041410 BUNN-O-MA TIC COMMERCIAL PRODUCT WARRANTY Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows: 1) All equipment other than as specified below: 2 years parts and 1 year labor . 2) Electronic circuit and/or control boards: parts and labor for 3 years. 3) Compressors on refrigeration equipment: 5 years part[...]

3 INTRODUCTION This equipment dispenses granita-type and cold liquid drinks on demand from separate hoppers. Operating controls are accessible only through password protection. CONTENTS Warranty ........................................................................................................................ 2 Introduction ...................[...]

4 INITIAL SETUP CAUTION – The dispenser is ver y heavy! Use care when lifting or moving it. Use at least two people to lift or move the dispenser . 3. Remove the rear plastic plug from the trim strip between the ho pp er dr ip tr ay s an d loo sen th e auger motor cover screws. 2. Remove all shipping material, including the compressor support eye[...]

5 11. Thoroughly rinse the hoppers an d ins tal l th em over the auge rs and cooling drums. 15. Set the lid(s) on the hopper(s). Lift slightly and slide back or front for filling. 16. Plug in the hopper lid lamp cord(s). 17. Assemble the drip tray . INITIAL SETUP (CONT .) 12. Slide the hopper(s) into place and push down until the hop - per lock pl[...]

6 OPERA TING CONTROLS UL TRA-1 There are three of these switches that will be used for the operation of the dispenser . 1. switch (upper left corner of the control pad) This switch is the ON/OFF toggle switch which powers up the dispenser and the LCD display . When ON the Date and Time toggle back and forth continously except during programming. 2.[...]

7 OPERA TING CONTROLS UL TRA-2 There are five of these switches that will be used for the operation of the dispenser . 1. switch (upper left corner of the control pad) This switch is the ON/OFF toggle switch which powers up the dispenser and the LCD display . When ON the Date and Time toggle back and forth continously except during programming. 2.[...]

8 USING THE DISPENSER FOR GRANIT A-TYPE PRODUCTS 1. Lift the lid slightly for the selected hopper and slide back to gain access to the hopper . 2. Place the pre-mixed liquid product in the selected hopper . 3. a. Press and release the (ON/OFF) switch to power on the dispenser . b. Press and release the appropriate (ON/OFF) switch to start the Auger[...]

9 1 3 PROGRAMMING Using the menu-driven display on the front of the dispenser , the operator has the ability to alter or modify various parameters such as beverage consistency and set day/night “ON/OFF” times. The operator is also prompted to check a variety of periodic service functions or even a step-by-step cleaning routine. There is also th[...]

10 PROGRAMMING THE DISPENSER During normal operations, the Date, the Time, and the Serial Number toggle back and forth continuously . The following function screens are in the order they appear from the menu display . Each screen will have instructions and procedures to program the various functions of the dispenser . HOME SCREEN Displays the TIME,[...]

11 P3678 Set Consistency This function allows the operator to adjust the ice consistency , or torque of each auger when answered YES (“ICE”). T wo screens will appear for left and right. The operator can scroll through a range of a minimum of 1 (UL TRA) to a maximum of 16 (ICE). Factor y default is 10. SET THICKNESS ? NO YES LEFT 9 RIGHT 5 NOTE[...]

12 Install Date The following three screens will scroll after advancing past the function “Restore Defaults”. The Install Date and Time is recorded when the dispenser is powered on for the first 100 hours. The Install Date and Time cannot be reset and is stored in permanent memory . INST ALL DA TE JAN. 20, 2005 3:55:25 PM UL TRA VERSION # __._[...]

13 OTHER RECOMMENDA TIONS FOR YOUR DISPENSER • Whether liquid concentrate or granulated powder , all product must be thoroughly mixed BEFORE adding it to the hoppers. • For best results with granita-type products, use only products with an apparent brix of 12 or higher . Some products may work with an apparent brix as low as 9. Y our experiment[...]

14 10. Place all parts in a clean sink with mild hot water (120°F) and sanitizer solution. Allow all parts to soak for at least 5 minutes. Carefully wash all components with a clean wash cloth in the hot water and sanitizer solution. Use a clean, soft bristle brush as needed for the smaller components and tight areas. Do not immerse hopper lids. U[...]

15 1. Install the seal(s) over the flange at the rear of the cooling drum(s) and press the seal(s) firmly into place as shown. 2. Align the auger shaft(s) with the aug er(s) . Push the auger (s) as fa r as the y will g o a nd rot ate so th e flat fac e of the auger shaft is aligned with the flat face of the auger nose. 4. Thoroughly rinse the h[...]

16 Auto-fill Cleaning Instructions (With Brixing Pump Installed) Materials required 1. Non-sudsing liquid detergent (such as common household automatic dishwasher liquid detergent). 2. Household bleach (Sodium chloride solution: 5.25%) or equivalent. 3. Clean five (5) gallon bucket. 4. Measuring Cup 5. An adaptor is needed to hold the Q.C.D. (Qui[...]

17 USER NOTICES Carefully read and follow all notices on the equipment and in this manual. They were written for your protec- tion. All notices are to be kept in good condition. Replace any unreadable or damaged labels. 27442.0000 32162.0000 (UL TRA-2) 00986.0002 CHARGE T ype R404A, Amount 9.5 oz (269 gm) Design Pressures: High 215 psi (15 bar) (1.[...]