Carrier Access 3200 manual

Adit 3200 Q UICK S TART G UIDE Part Number: 002- 0246-0010 Product Release: 1.6 September 2007[...]

Copyright 2007 Carrier Access Corporation. All rig hts reserved. The information presented in this manual is subject t o change without notice an d does not represent a commitm ent on the part of Carrier Access Corporation. The hardware and softwa re described herein are furnished under a license or non- disclosure agreement. The hardware, software[...]

Q UICK S TART G UIDE Quick Start In this Guide  Unpacking and Inspection  Installation Environment  User Safety  Installation - Compliant Installation - Wall Mounting - Rack Mounting (O ptional Feature) - Adit 3104, 3200, 3300 and 3400 Battery Backup  Chassis Overview  Interface Connectors  Reset Button  Alarm/Status LEDs ?[...]

4 Adit 3200 - Relea se 1.6 Quick Start Unpacking and Inspection Unpacking and Inspection W ARNING! O BSERV E PRECAUTIONS FO R HANDLING ELECT ROSTATIC DEVICES . 1. Inspect containers for damag e during shipment . Report any damage to the freight carrier for possible insurance claims. 2. Compare packing list with office records. Report any discrepanc[...]

Adit 3200 - Release 1.6 5 Quick Start User Safety User Safety CAUTION! W HEN USING YOUR TEL EPHONE EQUIPMENT , BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE , ELECTRIC SHOCK AND INJURY TO PERSONS , INCLUDING THE FOLL OWING : z Do not use this prod uct near water for example, near a bathtub, washbowl, kitch en sink or[...]

6 Adit 3200 - Relea se 1.6 Quick Start Installatio n Compliant Installation NOTE: It is important the DS1/E1 Network Interface Cables are secured separately from the power and Signal Cables. 1. Inspect the unit. 2. Mount the unit, see Wall Mounting on page 7, or Rack Mounting (Optional Feature) on page 8 for detailed instructions. 3. Ground the uni[...]

Adit 3200 - Release 1.6 7 Quick Start Installation Wall Mounting Before beginning the mounting process , verify that the installation area is a stable environment, clean and free from extremes of temperature, shock, vibration and EMI. See Installation Environment on page 4. The Adit 3000 is delivered with mounting bracke ts th at can easily be atta[...]

8 Adit 3200 - Relea se 1.6 Quick Start Installatio n Rack Mounting (Optional Feature) NOTE: Rack mounting kits are availab le for both 19 and 23 inch racks. 1 Rack Unit (RU) of spacing is required above the Adit 3000 in the Rack Mount Unit. To rack mount the Adit 3000, fo llow the instructions below: 1. Attach bracket ears to Rack Mounting Tray usi[...]

Adit 3200 - Release 1.6 9 Quick Start Installation 4. Place the Adit on the Tray Slide and att ach with 4 screws removed in step 2. 5. Slide the assembled piece (Adit 3000 and Tray Slide) onto th e installed Rack Mounting Tray. 6. Secure the Tray Slide to the Rack Mounting Tray with the att ached screws on the Tray Slide. Tray Slide screws screws[...]

10 Adit 3200 - Relea se 1.6 Quick Start Installatio n Adit 3104, 3200, 3300 an d 3400 Battery Backup The Adit 3104, 32 00, 3300 and 3400 Battery Backup (P/N 730-0132 ), is a wall-mount battery backup unit to provide up to 8 hours battery backup . Please see the Battery Backup Use r Manual for prod uct information and instal lation instructions, whi[...]

Adit 3200 - Release 1.6 11 Quick Start Chassis Overview Chassis Overview (1) 10/100Ba se-T Ethernet (WAN) (4) 10/100Base- T Ethernet (LAN) Alarm Status Reset RS-232 Management Port Power/Battery/Status Ground Back Front (1) DS1/E1 (WAN) (E1-futur e)[...]

12 Adit 3200 - Relea se 1.6 Quick Start Interface Connectors Interface Connectors The following are the Adit 3200 interface connectors: Front of Adit z (1) DS1 WAN port (RJ-48C). Note: E1 will be in a future release. z (1) 10/100Base-T WAN port (RJ-45) z (4) 10/100Base-T switched LAN ports (RJ-45) Back of Adit z RS-232 craft port connector for loca[...]

Adit 3200 - Release 1.6 13 Quick Start Interface Connectors Power The Adit 3000 is powered by a limited -48 VDC Po wer source. The following options are available: z AC/DC Converter z Battery Backup module AC/DC Converter An AC/DC Converter generates 48VDC from any worldwide AC power source. To connect AC power: 1. Plug power connector from AC/DC c[...]

14 Adit 3200 - Relea se 1.6 Quick Start Interface Connectors RS-232 Craft Port (Female DB-9) The RS-232 craft port connector (female) is for co nnection to an external PC or Hayes-compatible modem for local or remote configuration, mana gement, and performance monitoring using the Adit 3000 Command Lin e Interface (CLI). The RS-232 craft port conne[...]

Adit 3200 - Release 1.6 15 Quick Start Interface Connectors DS1/E1 Connection Ports Each DS1/E1 connec tion port is equipped with a standard RJ-4 8C (female) on the Adit 3000 unit. Note: E1 will be available in a future release. The pinouts are as follows: DS1/E1 RJ-48C The pinouts are as follows: Note: This is a hub pinout, you will need a straigh[...]

16 Adit 3200 - Relea se 1.6 Quick Start Reset Button 10/100Base-TX Ethernet The 10/100Base-TX Ethernet (female) po rts provide connectivity for Router WAN and/or LAN ports and for manage ment connection via Telnet and/or SNMP to a Network Management System. Ethernet (RJ-45) The pinouts are as follows: The LEDs are as follows: Reset Button The syste[...]

Adit 3200 - Release 1.6 17 Quick Start Alarm/Status LEDs Alarm/Status LEDs LED State Description Critical Off No critical alarms present Red Critical alarms present. Critical alarms include: user-conf igured manor environment al inputs. Major Off No major alarms present Red Major alarm present. Major alarms include: user-conf igured manor environme[...]

18 Adit 3200 - Relea se 1.6 Quick Start Web-Based Management Web-Based Management The web-based mana gement interface allows you to control various system parameters. The interface is accessed through a web browser. To access the management console: NOTE: The following assumes that you have connected the PC to the LAN port of the Adit 3200. 1. Laun[...]

Adit 3200 - Release 1.6 19 Quick Start Setting up a CLI Connecti on Setting up a CLI Connection A CLI connection will require t he LAN or WAN IP ad dress of the unit. Note : If the WAN IP address is used, the remote admin WAN access must be enabled with th e following comman d sequence: NOTE: For Adit 3200 CLI commands see the Adit 3000 CLI Referen[...]

20 Adit 3200 - Relea se 1.6 Quick Start Log in Log in After successful connection, via telnet or HyperT erm, the user must login. Default Logins are: Login: admin Password: admin123 After successful login the prompt will be displayed as follows: Adit 3200> NOTE: It is recommended that you cha nge your password from the default.[...]

Adit 3200 - Release 1.6 21 Quick Start Key Enabled Software Features Key Enabled Software Features The Adit 3200 has additional features that are not pr ovided on the base system. These features can be purchased with the product or added later as needed . These features are enabled via a Software Key (example: G.729). The number of keyed features m[...]

22 Adit 3200 - Relea se 1.6 Quick Start Basic Configuration Basic Configuration The following configuration is divided into logical sections, where each sect ion configures an additional function. The first must be config ured before the second and so forth, however, yo u may stop at any section and not add the following feat ure. NOTE: The order i[...]

Adit 3200 - Release 1.6 23 Quick Start Basic Configuration Restore Factory Defaults If the unit is not out-of-the-box, you may want to verify t hat the unit is set to defaults. Note: This will reset the IP address back to th e default setting of 192.168.1.1. In the web-browser: z Select Advanced from the Navigation bar z Select Restore Defaults z S[...]

24 Adit 3200 - Relea se 1.6 Quick Start Basic Configuration Modify Default Admin User For security purposes it is recommended that the Ad ministrator User be changed from the default settings. Modify the Administrator User in the web-browser: z Select Advanced from the Navigation bar z Select Users icon z Select Administrato r, to open the profile.[...]

Adit 3200 - Release 1.6 25 Quick Start Basic Configuration z Modify the User info rmation, and select OK to save. It is important t o note that you need to have a minimum of on e user with Administrative Privileges . For users with other access levels, add a New Use r . Note: For security purposes, the password should be changed. z You will be requ[...]

26 Adit 3200 - Relea se 1.6 Quick Start Basic Configuration Configure Ethernet WAN Interface In the web-browser: 1. Select Network Connections from the Navigation bar. 2. It is recommended that you disable/delete the Serial1 port. 3. Select (click) Ethernet 2 (WAN Ethernet) connection to configure. 4. Select the Enable button, to configure the WAN [...]

Adit 3200 - Release 1.6 27 Quick Start Basic Configuration 6. Set Internet Protocol to Obtain an IP Address Automatically , from the pulldown menu. This will enable the Adit 3200 as a DHCP Client. Leave the other fields to their default settings. 7. Select Apply to apply the new settings.[...]

28 Adit 3200 - Relea se 1.6 Quick Start Basic Configuration Configure Serial 1 as WAN In the web-browser: 1. Select Network Connections from the Navigation bar. 2. Select Serial 1 . 3. Select Settings button. 4. Set Network to WAN . 5. Select Apply to apply the new settings.[...]