Chamberlain POWER DRIVE PD752D manual

The Chamberlain Group, Inc. 845 Larch Avenue Elmhurst, Illinois 60126-1 196 www .chamberlain.com GARAGE DOOR OPENER Models PD752D 3/4 HP PD752KLD 3/4 HP For Residential Use Only Owner’s Manual ■ Please read this manual and the enclosed safety materials carefully! ■ Fasten the manual near the garage door after installation. ■ The door WILL N[...]

2 T ABLE OF CONTENTS When you see these Safety Symbols and Signal Words on the following pages, they will alert you to the possibility of serious injury or death if you do not comply with the warnings that accompany them. The hazard may come from something mechanical or from electric shock. Read the warnings carefully . When you see this Signal Wor[...]

3 T o prevent damage to garage door and opener: • AL W A YS disable locks BEFORE installing and operating the opener . • ONL Y operate garage door opener at 120V , 60 Hz to avoid malfunction and damage. T o prevent possible SERIOUS INJUR Y or DEA TH: • AL W A YS call a trained door systems technician if garage door binds, sticks, or is out of[...]

4 Safety Reversing Sensor Horizontal and vertical reinforcement is needed for lightweight garage doors (fiberglass, steel, aluminum, door with glass panels, etc.). See page 23 for details. Header Wall Safety Reversing Sensor Gap between floor and bottom of door must not exceed 1/4" (6 mm). Extension Spring Torsion Spring Access Door OR Slack i[...]

5 Access Door Safety Re v ersing Sensor Safety Re v ersing Sensor Gap b et w een floor and b ottom of door m u st not exceed 1/4" (6 mm). Door Bracket Straight Door Arm Garage Door CLOSED POSITION Header Bracket C u r v ed Door Arm Chain Emergency Release Rope & Handle Ca b le Rail T rolley Stop Bolt Header W all Planning (Continued) ONE-P[...]

6 Straight Door Arm Section C u r v ed Door Arm Section Safety La b els and Literat u re 2-Cond u ctor Bell W ire W hite & W hite/Red Chain and Ca b le Chain Spreader Hanging Brack ets Door Bracket SECURITY ✚ ® 3-B u tton Remote Control w ith Visor Clip (2) T r olley Safety Sensor Brack et (2) Rail Center/Back Sections "U" Brack et[...]

7 Master Link (2) Idler Bolt (1) Nut 3/8" (1) T rolley Threaded Shaft (1) Lock W asher 3/8" (1) Lock Nut 1/4"-20 (2) Wing Nut 1/4"-20 (2) Carriage Bolt 1/4"-20x1/2" (2) Handle Nut 5/16"-18 (8) Ring Fastener (3) Insulated Staples (30) Drywall Anchors (2) Clevis Pin 5/16"x1" (1) Rope Lock W asher 5/16"[...]

FRONT RAIL (TOP) KEEP LARGER HOLE O N TOP 8 ASSEMBL Y STEP 1 Assemble the Rail & Install the T rolley T o avoid installation difficulties, do not run the garage door opener until instructed to do so. T o prevent INJUR Y from pinching, keep hands and fingers away from the joints while assembling the rail. WARN ING CAUTION WARN ING WARN ING Front[...]

9 T o avoid SERIOUS damage to garage door opener , use ONL Y those bolts/fasteners mounted in the top of the opener . ASSEMBL Y STEP 2 Fasten the Rail to the Motor Unit • Insert a 1/4"-20x2-1/2 bolt, washer and spacer into the cover protection bolt hole on the back end of the rail as shown. Install lower spacer and washer then tighten secure[...]

10 T o avoid possible SERIOUS INJURY to fingers from moving garage door opener: • AL WA YS keep hand clear of sprocket while operating opener . • Securely attach chain spreader BEFORE operating. Leave Chain and Cable Inside Dispensing Carton to Prevent Kinking. Dispensing Carton Keep Chain and Cable Taut When Dispensing WARN ING CAUTION WARN IN[...]

11 INST ALLA TION ASSEMBL Y STEP 5 Tighten the Chain • Spin the inner nut and lock washer down the trolley threaded shaft, away from the trolley . • T o tighten the chain, turn outer nut in the direction shown (Figure 1). • When the chain is approximately 1/4" (6 mm) above the base of the rail at its midpoint, re-tighten the inner nut to[...]

12 INST ALLA TION STEP 1 Determine the Header Bracket Location Installation procedures vary according to garage door types. Follow the instructions which apply to your door . 1. Close the door and mark the inside vertical centerline of the garage door . 2. Extend the line onto the header wall above the door . Y ou can fasten the header bracket with[...]

13 Lag Scre w s 5/16"x9x1-5/ 8 " – Finished Ceilin g – Door Spring Header W all UP Ceiling Mo u nting Holes 6" (15 cm) Maxim u m Header Bracket Vertical Centerline of Garage Door Garage Door Vertical Centerline of Garage Door INST ALLA TION STEP 2 Install the Header Bracket Y ou can attach the header bracket either to the wall ab[...]

14 INST ALLA TION STEP 3 Attach the Rail to the Header Bracket NOTE: (Optional) With some existing installations, you may re-use the old header bracket with the two plastic spacers included in the hardware bag. Place the spacers inside the bracket on each side of the rail, as illustrated. • Position the opener on the garage floor below the header[...]

15 ONE-PIECE DOOR WITHOUT TRACK A 2x4 on its side is convenient for setting an ideal door-to-rail distance. • Remove foam packaging. • Raise the opener onto a stepladder . Y ou will need help at this point if the ladder is not tall enough. • Open the door all the way and place a 2x4 on its side on the top section of the door beneath the rail.[...]

16 INST ALLA TION STEP 5 Hang the Opener Three representative installations are shown. Y ours may be different. Hanging brackets should be angled (Figure 1) to provide rigid support. On finished ceilings (Figure 2 and Figure 3), attach a sturdy metal bracket to structural supports before installing the opener . This bracket and fastening hardware a[...]

T o prevent possible SERIOUS INJURY or DEA TH from electrocution: • Be sure power is not connected BEFORE installing door control. • Connect ONL Y to 24 VOL T low voltage wires. T o prevent possible SERIOUS INJURY or DEA TH from a closing garage door: • Install door control within sight of garage door , out of reach of children at a minimum h[...]

18 INST ALLA TION STEP 7 Install the Lights • Install a 100 watt maximum light bulb in each socket. Light bulb size should be A19, standard neck only . The lights will turn O N and remain lit for approximately 4-1/2 minutes when power is connected. Then the lights will turn OFF . • Insert bottom lens tabs into slots on chassis. T ilt towards ch[...]

19 INST ALLA TION STEP 9 Electrical Requirements T o avoid installation difficulties, do not run the opener at this time. T o reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet. If the plug doesn't fit into the outlet you have, co[...]

20 In v isi b le Light Beam Protection Area Safety Re v ersing Sensor 6" (15 cm) max. a b o v e floor Safety Re v ersing Sensor 6" (15 cm) max. a b o v e floor Facing the door from inside the garage INST ALLA TION STEP 10 Install The Protector System ® The safety reversing sensor must be connected and aligned correctly before the garage [...]

21 DOOR TRACK MOUNT (RIGHT SIDE) Indicator Light Lens Lip Sensor Bracket Door T rack FLOOR MOUNT (RIGHT SIDE) W ALL MOUNT (RIGHT SIDE) Indicator Light Sensor Bracket Lens Extension Bracket (See Accessories) Inside G arage W al l (Provided with Extension Bracket) (Provided with Extension Bracket) Figure 1 Figure 2 Figure 3 Figure 4 W ALL MOUNT (RIGH[...]

22 Carriage Bolt 1/4"-20x1/2" Lens Wing N u t 1/4"-20 Fi g ure 5 MOUNTING AND WIRING THE SAFETY REVERSING SENSORS • Slide a 1/4"-20x1/2" carriage bolt head into the slot on each sensor . Use w ing nuts to fasten sensors to brackets, w ith lenses pointing to w ard each other across the door . Be sure the lens is not obstru[...]

23 Fiberglass, aluminum or lightweight steel garage doors WILL REQUIRE reinforcement BEFORE installation of door bracket. Contact your door manufacturer for reinforcement kit. WARN ING CAUTION WARN ING WARN ING INST ALLA TION STEP 11 Fasten the Door Bracket Follo w instructions w hich apply to your door type as illustrated belo w or on the follo w [...]

24 Header W all V ertical Centerline of Garage Door Finished Ceiling Optional Placement of Door Bracket Header Bracket Door Bracket 2x4 S u pport For a door with no exposed framing, or for the optional installation, u se lag screws 5/16"x1-1/2" (Not Provided) to fasten door b racket. MET AL DOOR T op of Door (Inside Garage) Door Bracket O[...]

25 INST ALLA TION STEP 12 Connect Door Arm to T rolley Follo w instructions w hich apply to your door type as illustrated belo w and on the follo w ing page. SECTIONAL DOORS ONL Y • Make sure garage door is fully closed. Pull the emergency release handle to disconnect the outer trolley from the inner trolley . Slide the outer trolley back (a w ay[...]

26 ALL ONE-PIECE DOORS 1. Assemble the door arm, Figure 4: • Fasten the straight and cur v ed door arm sections together to the longest possible length ( w ith a 2 or 3 hole o v erlap). • W ith the door closed, connect the straight door arm section to the door bracket w ith the 5/16"x1-1/4" cle v is pin. • Secure w ith a ring fasten[...]

27 ADJUSTMENT STEP 1 Adjust the UP and DOWN T ravel Limits Limit adjustment settings regulate the points at w hich the door w ill stop w hen mo v ing up or do w n. T o operate the opener , press the Door Control push bar . Run the opener through a complete tra v el cycle. • Does the door open and close completely? • Does the door stay closed an[...]

28 ADJUSTMENT STEP 2 Adjust the Force Force adjustment controls are located on the right panel of the motor unit. Force adjustment settings regulate the amount of po w er required to open and close the door . If the forces are set too light, door tra v el may be interrupted by nuisance re v ersals in the do w n direction and stops in the up directi[...]

29 Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSL Y INJURED or KILLED by a closing garage door . • Safety reversal system MUST be tested ever y month. • If one control (force or travel limits) is adjusted, the other control may also need adjustment. • After ANY adjustments are made[...]

30 OPERA TION Using Y our Garage Door Opener Y our Security ✚ ® opener and hand-held remote control ha v e been factory-set to a matching code w hich changes w ith each use, randomly accessing o v er 100 billion ne w codes. Y our opener w ill operate w ith up to eight Security ✚ ® remote controls and one Security ✚ ® Keyless Entry System. [...]

31 Additional feature when used with the 3-Button hand-held remote T o control the opener lights: In addition to operating the door , you may program the remote to operate the lights. 1. With the door closed, press and hold a small remote button that you want to control the light. 2. Press and hold the Light button on the door control. 3. While hol[...]

32 CARE OF YOUR OPENER LIMIT AND FORCE ADJUSTMENTS: Weather conditions may cause some minor changes in door operation requiring some re-adjustments, particularly during the first year of operation. Pages 27 and 28 refer to the limit and force adjustments. Only a screwdriver is required. Follow the instructions carefully . Repeat the safety reverse [...]

33 HA VING A PROBLEM? 1. My door will not close and the light bulbs blink on my motor unit: The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direction. • V erify the safety sensors are properly installed, aligned and free of any obstructions. Refer to Installation Step 10: Ins[...]

34 Installed Safety Re v ersing Sensor Safety Re v ersing Sensor Bell W ire LED or Diagnostic LED "Learn" B u tton KG 1 3 9 7 5 KG 1 3 9 7 5 Diagnostics Located On Motor Unit Y our garage door opener is programmed with self-diagnostic capabilities. The “Learn” button/diagnostic LED will flash a number of times then pause signifying it[...]

*3-Button Remotes If provided with your garage door opener , the large button is factory programmed to operate it. Additional buttons on any Security ✚ ® 3-Button remote or compact remote can be programmed to operate other Security ✚ ® garage door openers. T o Erase All Codes From Motor Unit Memory T o deactivate any unwanted remote, first er[...]

1. Press and release the “learn” button on motor unit. The learn indicator light will glow steadily for 30 seconds. 2. Within 30 seconds, enter a four digit personal identification number (PIN) of your choice on the keypad. Then press and hold the ENTER button. 3. Release the button when the motor unit lights blink. It has learned the code. If [...]

3 1 5 4 2 6 37 REP AIR P AR TS Rail Assembly Parts KEY P ART NO. NO. DESCRIPTION 1 4A1008 Master link kit 2 41C5141-1 Complete trolley assembly 3 41A5665-2 Complete rail 4 144C56 Idler pulley 5 41A5807-3 Chain and cable 6 12D598-1 “U” bracket NOT SHOWN 183A163 Wear pads 7 10 12 5 N O TIC E 6 4 3 2 9 13 8 1 11 LO C K LIG H T Installation Parts K[...]

Motor Unit Assembly Parts 38 DN UP Brown Wire (Down) Contact LIMIT SWITCH ASSEMBLY Grey Wire Yellow Wire (Up) Contact Center Limit Contact Drive Gear 2 4 3 1 14 18 8A 16 5 17 9 10 15 13 12 6 6 11 8B 8C 7 7 KEY P ART NO. NO. DESCRIPTION 1 41A5615 Chain Spreader 2 41A5585 Gear and sprocket assembly . Complete with: Spring washer , thrust washer , ret[...]

39 ACCESSORIES LOCK LIGHT C L O S E D O P E N L O C K L IG H T 3-Button SECURITY ✚ ® Remote Control: Includes visor clip. SECURITY ✚ ® Keyless Entry: Enables homeowner to operate garage door opener from outside by entering a password on a specially designed keyboard. Also can add a temporary password for visitors or service persons. This temp[...]

© 2006, The Chamberlain Group, Inc. 1 14A3060E All Rights Reserved CHAMBERLAIN ® SER VICE IS ON CALL OUR LARGE SERVICE ORGANIZA TION SP ANS AMERICA INST ALLA TION AND SER VICE INFORMA TION IS AS NEAR AS YOUR TELEPHONE. SIMPL Y DIAL OUR TOLL FREE NUMBER: 1-800-528-9131 www .chamberlain-diy .com For professional installation, parts and service, con[...]