Chevrolet 2010 Aveo Sedan manual

2010 Chevrolet A veo Owner Manual M In Brief ................ .......... ........... ....... 1 - 1 I n s t r u m e n t P a n e l ... .............................. 1 - 2 Initial Drive Information . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 V ehicle Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-18 Performance and Maintenance . . . . . . . . . . . . . . . . . . 1-22 Seats and Restraint System ...................... 2 - 1 Head Restraints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 F r o n t S e a t s ...................... ................. 2 - 4 Rear Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [...]

2010 Chevrolet A veo Owner Manual M Service and Appearance Care . . . . . . . . . . . . . . . . . . . 6-1 S e r v i c e .................................... ....... 6 - 4 Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6 Checking Things Under the Hood . . . . . . . . . . . . . . . 6-1 1 H e a d l a m p A i m i n g ............................... 6 - 4 3 B u l b R e p l a c e m e n t ... ........................... 6 - 4 3 Windshield Wiper Blade Replacement . . . . . . . . . . . 6-50 T i r e s ............. ............................... 6 - 5 1 Appearance Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-79 V ehicle Ident[...]

GENERAL MOTORS, GM, the GM Emblem, CHEVROLET , the CHEVROLET Emblem, and the name A VEO are registered trademarks of General Motors. This manual describes features that may or may not be on your specific vehicle either because they are options that you did not purchase or due to changes subsequent to the printing of this owner manual. Please refer to the purchase documentation relating to your specific vehicle to confirm each of the features found on your vehicle. For vehicles first sold in Canada, substitute the name “ General Motors of Canada Limited ” for Chevrolet Motor Division wherever it appears in this manual. Keep this manual in the vehicle for quick reference. Canadian Owners P[...]

Safety W arnings and Symbols W arning messages found on vehicle labels and in this manual describe hazards and what to do to avoid or reduce them. Danger indicates a hazard with a high level of risk which will result in serious injury or death. W arning or Caution indicates a hazard that could result in injury or death. { W ARNING: These mean there is something that could hurt you or other people. Notice: This means there is something that could result in property or vehicle damage. This would not be covered by the vehicle's warranty . A circle with a slash through it is a safety symbol which means “ Do Not, ” “ Do not do this, ” or “ Do not let this happen. ” V ehicle Symbo[...]

V ehicle Symbol Chart Here are some additional symbols that may be found on the vehicle and what they mean. For more information on the symbol, refer to the index. 9 : Airbag Readiness Light # : Air Conditioning ! : Antilock Brake System (ABS) g : Audio Steering Wheel Controls or OnStar ® $ : Brake System Warning Light " : Charging System I : Cruise Control B : Engine Coolant T emperature O : Exterior Lamps # : Fog Lamps . : Fuel Gauge + : Fuses i : Headlamp High/Low-Beam Changer j : LA TCH System Child Restraints * : Malfunction Indicator Lamp : : Oil Pressure } : Power / : Remote V ehicle Start > : Safety Belt Reminders 7 : T ire Pressure Monitor F : T raction Control M : Windshie[...]

2 NOTES vi[...]

Section 1 In Brief Instrument Panel .................................. . 1-2 Initial Drive Information .. ........................ . 1-3 Starting the Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Remote Keyless Entry (RKE) System . . . . . . . . . . . 1-4 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 Liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 T r u n k R e l e a s e ... . .............................. 1 - 5 W i n d o w s ........................................ 1 - 6 Seat Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7 Second Row Seats . . . [...]

Instrument Panel 1-2[...]

A. Outlet Adjustment on page 4 ‑ 19 . B. Instrument Panel Cluster on page 4 ‑ 22 . C. Clock on page 4 ‑ 15 . D. Hood Release on page 6 ‑ 12 . E. Horn on page 4 ‑ 3 . F . Audio System(s) on page 4 ‑ 39 . G. Climate Control System on page 4 ‑ 16 . H. Ashtray . See Ashtray(s) and Cigarette Lighter on page 4 ‑ 15 . I. Cupholders on page 3 ‑ 36 . J. Cigarette Lighter . See Ashtray(s) and Cigarette Lighter on page 4 ‑ 15 . K. Hazard Warning Flashers on page 4 ‑ 3 . L. Glove Box on page 3 ‑ 36 . Initial Drive Information This section provides a brief overview about some of the important features that may or may not be on your specific vehicle. For more detailed information, [...]

Remote Keyless Entry (RKE) System The RKE transmitter is used to remotely lock and unlock the doors from up to 20 m (65 feet) away from the vehicle. Hatchback Sedan Press K to unlock all of the doors. Press Q to lock all of the doors. Press V and hold for approximately one second to open the trunk on the sedan model. Press 3 to sound the panic alarm on the hatchback model. Press any of the buttons on the transmitter to turn off the alarm. The LED light (A) on the transmitter flashes when the buttons on the transmitter are pressed. If the light does not flash the transmitter battery needs to be replaced. See Keys on page 3 ‑ 2 and Remote Keyless Entry (RKE) System Operation on page 3 ‑ 4 [...]

Liftgate T o unlock the liftgate on the hatchback model from outside the vehicle, use the key in the lock cylinder or use the RKE transmitter , if equipped. The handle is located above the right side of the license plate. Pull the handle toward you and raise the liftgate. T o lock the liftgate, use the key or the RKE transmitter , if equipped. The liftgate can also be locked or unlocked by the central door unlocking system. For more information see Liftgate (Hatchback) on page 3 ‑ 10 . T runk Release The vehicle may have a release button located on the driver door . Press it to open the trunk. 1-5[...]

The vehicle may have a trunk release lever located on the outboard side of the driver seat. Pull the lever to open the trunk. For more information see T runk on page 3 ‑ 8 . Windows Manual Windows Use the window crank to open and close each window . The rear windows do not open fully . For more information see Manual Windows on page 3 ‑ 13 . Power Windows On vehicles with power windows, the switches for all windows are located on the driver door armrest. Each passenger door has a switch for its own window . The ignition must be in ON/RUN to use the power windows. T o lower the window , press and hold the switch. T o raise the window , lift up on the switch. Release the switch when the wi[...]

Seat Adjustment Manual Seats 1. Lift the bar under the front of the seat to unlock it. 2. Slide the seat to the desired position and release the bar . Push and pull on the seat to make sure it is locked into place. Seat Height Adjuster T urn the knob located on the outboard side of the seat to adjust the height of the driver seat cushion. T urn the knob forward to raise the seat and rearward to lower it. 1-7[...]

Manual Lumbar Move the adjustment lever , located on the outboard side of the seatback, up or down to one of three positions to increase or decrease the lumbar support. The highest position provides the most support and the lowest position provides the least support. Reclining Seatbacks This lever is located on the outboard side of the front seats. 1. Lift the recline lever . 2. Move the seatback to the desired position then release the lever to lock the seatback in place. 3. Push and pull on the seatback to make sure it is locked in place. See Reclining Seatbacks on page 2 ‑ 6 . 1-8[...]

Second Row Seats The rear seatbacks can be folded down to increase cargo space. For detailed instructions see Rear Seat Operation (Sedan) on page 2 ‑ 8 or Rear Seat Operation (Hatchback) on page 2 ‑ 10 . Head Restraint Adjustment The vehicle's front seats have adjustable head restraints in the outboard seating positions. Do not drive until the head restraints for all occupants are installed and adjusted properly . For more information see Head Restraints on page 2 ‑ 2 . Safety Belt Refer to the following sections for important information on how to use safety belts properly . . Safety Belts: They Are for Everyone on page 2 ‑ 14 . . How to Wear Safety Belts Properly on page 2 ‑[...]

Sensing System for Passenger Airbag The passenger sensing system will turn off the right front passenger frontal airbag and seat ‐ mounted side impact airbag (if equipped) under certain conditions. The driver airbags are not affected by this. The passenger airbag status indicator will be visible, near the clock, located in the center of the instrument panel when the vehicle is started. United States Canada See Passenger Sensing System on page 2 ‑ 65 for important information. Mirror Adjustment Exterior Mirrors Manual Outside Mirrors The control for the outside manual mirrors are located next to each mirror . Manually fold the mirrors inward to prevent damage when going through an automat[...]

Power Outside Mirrors The control is located on the instrument panel, left of the steering wheel. The ignition must be turned to ON/RUN to adjust the mirrors. 1. Select the mirror by moving the selector switch to L for the driver side mirror or R for the passenger side. 2. Press one of the four arrows located on the control pad to move the mirror to the desired direction. For more information, see: . Outside Power Mirrors on page 3 ‑ 35 . . Outside Manual Mirrors on page 3 ‑ 34 . Interior Mirror Hold the mirror in the center to move it up or down and side to side. Adjust the mirror to avoid glare from the headlamps behind you. Push the tab forward for daytime use and pull it for nighttim[...]

Steering Wheel Adjustment The tilt wheel lever is located under the steering column, slightly to the left. T o adjust the steering wheel: 1. Pull the lever down. 2. Move the steering wheel up or down into a comfortable position. 3. Pull the lever up to lock the wheel in place. See Tilt Wheel on page 4 ‑ 3 . Interior Lighting Dome Lamp The vehicle has a dome lamp located in the overhead console. Move the switch to the following positions: ON: The light comes on and stays on. O : The light comes on when a door is opened. The light turns off when all the doors are closed. OFF: The light remains off even when a door is opened. Be sure all doors and trunk lid or hatch are completely closed or t[...]

Exterior Lighting Uplevel shown, Base similar The lever on the left side of the steering column operates the exterior lamps. 3 : T urns on the headlamps and other exterior lamps. The headlamps automatically turn off when the ignition key is turned to LOCK/OFF or ACC/ACCESSORY . ; : T urns on the parking lamps, together with the taillamps, license plate lamp, and instrument panel lights. OFF: Turns all the lamps off, except the Daytime Running Lamps (DRL). For more information, see: . Exterior Lamps on page 4 ‑ 1 1 . . Daytime Running Lamps (DRL) on page 4 ‑ 12 . . Fog Lamps on page 4 ‑ 12 . 1-13[...]

Windshield Wiper/W asher Sedan shown Hatchback shown The lever is located on the right side of the steering column. The ignition must be turned to ON/RUN to operate the windshield wipers. HI: Fast wipes. LO: Slow wipes. INT : Move to this position for a delayed wiping cycle. T urn the band on the windshield wiper toward F AST or SLOW for a shorter or longer delay between wipes. The wiper speed can only be adjusted when the lever is in the INT position. OFF: Turns the windshield wipers of f. Misting Function Move the lever toward INT for a single wiping cycle. Hold it there until the windshield wipers start; then let go. For several wipes, hold the band toward INT longer . Windshield W asher [...]

Climate Controls For vehicles with these climate control systems, the heating, cooling, and ventilation can be controlled for the vehicle. Climate Control System with Heater and Air Conditioning A. T emperature Control B. Fan Control C. Air Delivery Mode Control D. Air Conditioning (A/C) E. Air Recirculation F . Rear Window Defogger Climate Control System with Heater Only A. T emperature Control B. Fan Control C. Air Delivery Mode Control D. Rear Window Defogger E. Outside Air/Recirculation See Climate Control System on page 4 ‑ 16 . 1-15[...]

T ransmission Automatic T ransmission Hold Mode If the vehicle's transmission has hold mode, you can select this mode to allow the automatic transmission to stay in a specific gear range. Select hold mode to help the vehicle maintain traction on slippery road surfaces, such as snow , mud, or ice. Press the HOLD button on the shift lever console to turn on hold mode. Press the button again to turn off hold mode, and return to normal automatic transmission operation. 1-16[...]

When Hold Mode is selected in D4 (Drive), the transmission is held in 3 (Third) gear , which locks out D4 (Drive). This allows for engine braking when slowing from higher speeds. When Hold Mode is selected in 2 (Second), the transmission will start in 2 (Second) gear instead of 1 (First), helping to reduce wheel spin when starting out on slippery surface such as snow , mud or ice. Since selecting Hold Mode in D4 (Drive) locks the transmission in 3 (Third), and prevents downshifts to 2 (Second) or 1 (First), acceleration from a stop or near stop on dry pavement will be slower than expected. Hold Mode should not be selected during these situations. See Automatic T ransmission Operation on page[...]

V ehicle Features Radio(s) Radio with CD shown O : Press and release to turn the system on. Press and hold this knob for more than two seconds to turn the system off. T urn to increase or decrease the volume. When the system is on, press and release O to mute the system. Press and release O again to turn the sound back on. BAND: Press to choose FM, AM, or XM ™ (if equipped). u SEEK: Press to seek the next radio station with a strong signal in the selected band. t SEEK: Press to seek the previous radio station with a strong signal in the selected band. [ TUNE: Press to go to the next station manually . r TUNE: Press to go to the previous station manually . SCAN/AST : Press to scan radio sta[...]

Press to play a CD while a portable audio device is playing. Press CD/AUX a second time for the system to begin playing audio from the connected portable audio player . The portable audio device continues playing until it is turned off. For more information about these and other radio features, see Audio System(s) on page 4 ‑ 39 . Storing a Favorite Station A maximum of 36 stations can be programmed as favorites using the six pushbuttons positioned below the radio station frequency labels and by using the radio favorites page button (F A V button). Press the F A V button to go through up to six pages of favorites, each having six favorite stations available per page. If Automatic Store is [...]

Steering Wheel Controls Front View of the Steering Wheel Controls Side View of the V olume Control If the vehicle has this feature, some audio controls can be adjusted at the steering wheel. PWR: Press and release to turn the system on and off. When the system is on, press and release for a short time to mute the system. Press and release again to turn the sound back on. + VOLUME − : Press the toggle bar located below the + VOLUME − to adjust the volume. MODE: Press and release this button multiple times to cycle through the audio playback options that are available on the vehicle. SEEK: Press and release to go to the next preset station, or CD track. Press and hold for a long time to go[...]

Cruise Control The cruise control buttons are located on the right side of the steering wheel. I / O : Press to turn the cruise control on or off. RES+: Press to make the vehicle accelerate or resume to a previously set speed. SET − : Press to set the speed or make the vehicle decelerate. See Cruise Control on page 4 ‑ 8 . Power Outlets Accessory power outlets can be used to plug in auxiliary electrical equipment, such as a cellular phone. The accessory power outlet is located next to the parking brake on the center console. T o use the accessory power outlet, remove the protective cap. When not in use, always cover the outlet with the protective cap. The accessory power outlet is operat[...]

Sunroof On vehicles with this feature, the switch is located on the headliner between the sun visors and can only be operated when the ignition is turned to ON/RUN. T o vent the sunroof, open the sunshade and then press and hold the driver side switch. T o close, press the passenger side switch. T o fully open the sunroof, press and hold the passenger side switch. The sunshade will open with the sunroof. T o close, press the driver side switch. Manually close the sunshade. For more information see Sunroof on page 3 ‑ 37 . Performance and Maintenance Tire Pressure Monitor This vehicle may have a T ire Pressure Monitor System (TPMS). The T ire Pressure Monitor alerts you when a significant r[...]

Y ou may notice during cooler conditions that the low tire pressure warning light will appear when the vehicle is first started and then turn off as you drive. This may be an early indicator that your tire pressures are getting low and the tires need to be inflated to the proper pressure. The T ire Pressure Monitor can alert you about low tire pressure, but it does not replace normal monthly tire maintenance. It is the driver ’ s responsibility to maintain correct tire pressures. See Tire Pressure Monitor System on page 6 ‑ 59 and Tire Pressure Monitor Operation on page 6 ‑ 60 . Engine Oil Life System The engine oil life system calculates engine oil life based on vehicle use and displa[...]

Hood Release T o open the hood: 1. Pull the hood release handle inside the vehicle. It is located on the lower left side of the instrument panel. 2. At the front of the vehicle, lift up on the secondary hood release lever , located under the front center of the vehicle. 3. Lift the hood and securely place the hood prop into the slot on the inner fender . See Hood Release on page 6 ‑ 12 . 1-24[...]

Driving for Better Fuel Economy Driving habits can affect fuel mileage. Here are some driving tips to get the best fuel economy possible. . Avoid fast starts and accelerate smoothly . . Brake gradually and avoid abrupt stops. . Avoid idling the engine for long periods of time. . When road and weather conditions are appropriate, use cruise control, if equipped. . Always follow posted speed limits or drive more slowly when conditions require. . Keep vehicle tires properly inflated. . Combine several trips into a single trip. . Replace the vehicle's tires with the same TPC Spec number molded into the tire's sidewall near the size. . Follow recommended scheduled maintenance. Roadside A[...]

OnStar ® OnStar ® uses several innovative technologies and live advisors to provide a wide range of safety , security , navigation, diagnostics, and calling services. Automatic Crash Response In a crash, built in sensors can automatically alert an OnStar advisor who is immediately connected to the vehicle to see if you need help. How OnStar Service Works Q : This blue button connects you to a specially trained OnStar advisor to verify your account information and to answer questions. ] : Push this red emergency button to get priority help from specially trained OnStar emergency advisors. X : Push this button for hands ‐ free, voice ‐ activated calling and to give voice commands for tur[...]

The OnStar system can record and transmit vehicle information. This information is automatically sent to an OnStar call center when Q is pressed, ] is pressed, or if the airbags or ACR system deploy . This information usually includes the vehicle's GPS location and, in the event of a crash, additional information regarding the crash that the vehicle was involved in (e.g. the direction from which the vehicle was hit). When the virtual advisor feature of OnStar hands-free calling is used, the vehicle also sends OnStar the vehicle's GPS location so they can provide services where it is located. Location information about the vehicle is only available if the GPS satellite signals are u[...]

2 NOTES 1-28[...]

Section 2 Seats and Restraint System Head Restraints ............................... ..... 2-2 Front Seats ......................................... 2-4 Manual Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Seat Height Adjuster . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5 Manual Lumbar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5 Reclining Seatbacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6 Rear Seats ... . .................. ................... 2-8 Rear Seat Operation (Sedan) . . . . . . . . . . . . . . . . . . . 2-8 Rear Seat Operation (Hatchback) . . . . . . . . . . . . . . 2-10 Safety Belts .......[...]

Head Restraints The front seats have adjustable head restraints in the outboard seating positions. { W ARNING: With head restraints that are not installed and adjusted properly , there is a greater chance that occupants will suffer a neck/spinal injury in a crash. Do not drive until the head restraints for all occupants are installed and adjusted properly . Adjust the head restraint so that the top of the restraint is at the same height as the top of the occupant's head. This position reduces the chances of a neck injury in a crash. 2-2[...]

Pull the head restraint up to raise it. T o lower the head restraint, press the button, located on the top of the seatback, and push the restraint down. Push down on the head restraint after the button is released to make sure that it is locked in place. The head restraints are not designed to be removed. The rear seats have head rests that are adjustable up and down. 2-3[...]

Front Seats Manual Seats { W ARNING: Y ou can lose control of the vehicle if you try to adjust a manual driver's seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to. Adjust the driver's seat only when the vehicle is not moving. 1. Lift the bar under the front of the seat to unlock it. 2. Slide the seat to the desired position and release the bar . 3. Push and pull on the seat to make sure it is locked into place. 2-4[...]

Seat Height Adjuster T urn the knob, located on the outboard side of the seat, to adjust the height of the driver seat. T urn the knob forward to raise the seat and rearward to lower it. Manual Lumbar On vehicles with front seat manual lumbar , the adjustment lever is located on the outboard side of the seatback. Move the lever up or down to one of three positions to increase or decrease lumbar support. The highest position provides the most support and the lowest position provides the least support. 2-5[...]

Reclining Seatbacks { W ARNING: Y ou can lose control of the vehicle if you try to adjust a manual driver's seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to. Adjust the driver's seat only when the vehicle is not moving. { W ARNING: If either seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always push and pull on the seatbacks to be sure they are locked. The seats have manual reclining seatbacks. The lever is located on the outboard side of the seats. T o recline the seatback: 1. Lift the recline lever . 2. Move the seatba[...]

{ W ARNING: Sitting in a reclined position when the vehicle is in motion can be dangerous. Even when buckled up, the safety belts cannot do their job when reclined like this. The shoulder belt cannot do its job because it will not be against your body . Instead, it will be in front of you. In a crash, you could go into it, receiving neck or other injuries. The lap belt cannot do its job either . In a crash, the belt could go up over your abdomen. The belt forces would be there, not at your pelvic bones. This could cause serious internal injuries. For proper protection when the vehicle is in motion, have the seatback upright. Then sit well back in the seat and wear the safety belt properly . [...]

Rear Seats Rear Seat Operation (Sedan) Folding the Seatbacks The rear seatbacks can be folded down to increase cargo space. T o fold down the seatbacks: Notice: Folding a rear seat with the safety belts still fastened may cause damage to the seat or the safety belts. Always unbuckle the safety belts and return them to their normal stowed position before folding a rear seat. 1. Remove the safety belt strap from the safety belt guide by pulling it through the slot. 2. Push the head restraints all the way down. 3. Unlatch the center safety belt by pressing the red button on the buckle. 2-8[...]

4. Detach the center safety belt from the mini buckle by inserting the ignition key into the slot in the mini buckle, pressing the release button, and allowing the belt to retract. 5. Pull up the release knob located on top of either of the rear seatbacks. 6. Fold the rear seatback forward and down. 2-9[...]

Unfolding the Seatbacks T o return the seatback to the upright position: 1. Hook the safety belts into the safety belt guide. 2. Lift the seatback up and push it to its original position. { W ARNING: If either seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always push and pull on the seatbacks to be sure they are locked. 3. Push down and rearward firmly on the top of the seatbacks until it latches securely in the fully upright position. 4. T o reattach the center seat safety belt to the mini buckle, pull it from the retractor . 5. Push the latch plate at the end of the safety belt strap into the mini-buckle until [...]

3. Detach the center safety belt from the mini buckle by inserting the key into the slot in the mini buckle, pressing the release button, and allowing it to retract. 4. Pull up the release knob, located on the top of the seatbacks, and fold the seatbacks forward and down. Notice: Folding a rear seat with the safety belts still fastened may cause damage to the seat or the safety belts. Always unbuckle the safety belts and return them to their normal stowed position before folding a rear seat. 5. Move the safety belt buckles and safety belt in the center seating position out of the space between the seatbacks and the seat cushion so they are not in the way as the seat is being folded. 2-1 1[...]

6. Firmly pull the release handles on the rear side of the seat cushion to unlock the seat cushion. 7. Lift the seat cushion up and flip it forward. 8. Clip the hook to the front seat head restraint to keep the rear seat secure. Unfolding the Seats T o return the rear seats to the normal seating position: 1. Unclip the hook from the front seat head restraint. 2. Position the buckles in back of the seat latches when moving the rear seats to the sitting position. 2-12[...]

Notice: Damage to the safety belt buckle or rear seat locking mechanism can occur if the safety belt and buckles are pinched under the rear seat cushion. Do not place the safety belt and buckles on the floor under the rear seat cushion when the rear seat is put back to the sitting position. 3. Push the seat cushion down to its original position until it latches securely . Try to pull up on the seat to make sure it is locked in place. 4. Hook the safety belts in the outboard seating positions into the retaining clips. { W ARNING: A safety belt that is improperly routed, not properly attached, or twisted will not provide the protection needed in a crash. The person wearing the belt could be se[...]

7. Return the safety belt buckles and the center seat safety belt to their original position between the rear seatback and the seat cushion. Make sure the straps of the safety belt and buckles are not twisted. 8. T o reattach the center seat safety belt to the mini buckle, pull it from the retractor . { W ARNING: If either seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always push and pull on the seatbacks to be sure they are locked. 9. Push down and rearward firmly on the top of the seatbacks until they latch securely in the fully upright position. Safety Belts Safety Belts: They Are for Everyone This section of [...]

{ W ARNING: It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using a safety belt properly . This vehicle has indicators as a reminder to buckle the safety belts. See Safety Belt Reminders on page 4 ‑ 24 for additional information. In most states and in all Canadian provinces, the law requires wearing safety belts. Here is why: Y ou never know if you will be in a crash. If you do have a crash, you do not know [...]

Put someone on it. Get it up to speed. Then stop the vehicle. The rider does not stop. 2-16[...]

The person keeps going until stopped by something. In a real vehicle, it could be the windshield... or the instrument panel... 2-17[...]

or the safety belts! With safety belts, you slow down as the vehicle does. Y ou get more time to stop. Y ou stop over more distance, and your strongest bones take the forces. That is why safety belts make such good sense. Questions and Answers About Safety Belts Q: Will I be trapped in the vehicle after a crash if I am wearing a safety belt? A: Y ou could be — whether you are wearing a safety belt or not. But your chance of being conscious during and after an accident, so you can unbuckle and get out, is much greater if you are belted. And you can unbuckle a safety belt, even if you are upside down. Q: If my vehicle has airbags, why should I have to wear safety belts? A: Airbags are supple[...]

Q: If I am a good driver, and I never drive far from home, why should I wear safety belts? A: Y ou may be an excellent driver , but if you are in a crash — even one that is not your fault — you and your passenger(s) can be hurt. Being a good driver does not protect you from things beyond your control, such as bad drivers. Most accidents occur within 25 miles (40 km) of home. And the greatest number of serious injuries and deaths occur at speeds of less than 40 mph (65 km/h). Safety belts are for everyone. How to Wear Safety Belts Properly This section is only for people of adult size. Be aware that there are special things to know about safety belts and children. And there are different [...]

Sit up straight and always keep your feet on the floor in front of you. The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones and you would be less likely to slide under the lap belt. If you slid under it, the belt would apply force on your abdomen. This could cause serious or even fatal injuries. The shoulder belt should go over the shoulder and across the chest. These parts of the body are best able to take belt restraining forces. The shoulder belt locks if there is a sudden stop or crash. 2-20[...]

Q: What is wrong with this? A: The shoulder belt is too loose. It will not give as much protection this way . { W ARNING: Y ou can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury . The shoulder belt should fit snugly against your body . 2-21[...]

Q: What is wrong with this? A: The lap belt is too loose. It will not give nearly as much protection this way . { W ARNING: Y ou can be seriously hurt if your lap belt is too loose. In a crash, you could slide under the lap belt and apply force on your abdomen. This could cause serious or even fatal injuries. The lap belt should be worn low and snug on the hips, just touching the thighs. 2-22[...]

Q: What is wrong with this? A: The belt is buckled in the wrong buckle. { W ARNING: Y ou can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not on the pelvic bones. This could cause serious internal injuries. Always buckle your belt into the buckle nearest you. 2-23[...]

Q: What is wrong with this? A: The belt is over an armrest. { W ARNING: Y ou can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt. The belt force would then be applied on the abdomen, not on the pelvic bones, and that could cause serious or fatal injuries. Be sure the belt goes under the armrests. 2-24[...]

Q: What is wrong with this? A: The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. { W ARNING: Y ou can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury . Also, the belt would apply too much force to the ribs, which are not as strong as shoulder bones. Y ou could also severely injure internal organs like your liver or spleen. The shoulder belt should go over the shoulder and across the chest. 2-25[...]

Q: What is wrong with this? A: The belt is behind the body . { W ARNING: Y ou can be seriously injured by not wearing the lap-shoulder belt properly . In a crash, you would not be restrained by the shoulder belt. Y our body could move too far forward increasing the chance of head and neck injury . Y ou might also slide under the lap belt. The belt force would then be applied right on the abdomen. That could cause serious or fatal injuries. The shoulder belt should go over the shoulder and across the chest. 2-26[...]

Q: What is wrong with this? A: The belt is twisted across the body . { W ARNING: Y ou can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly , or ask your dealer/retailer to fix it. 2-27[...]

Lap-Shoulder Belt All seating positions in the vehicle have a lap-shoulder belt. If you are using a rear seating position with a detachable safety belt and the safety belt is not attached, see Rear Seat Operation (Sedan) on page 2 ‑ 8 or Rear Seat Operation (Hatchback) on page 2 ‑ 10 for instruction on reconnecting the safety belt to the mini-buckle. The following instructions explain how to wear a lap-shoulder belt properly . 1. Adjust the seat, if the seat is adjustable, so you can sit up straight. T o see how , see “ Seats ” in the Index. 2. Pick up the latch plate and pull the belt across you. Do not let it get twisted. The lap-shoulder belt may lock if you pull the belt across y[...]

4. Push the latch plate into the buckle until it clicks. If the latch plate will not go fully into the buckle, check if the correct buckle is being used. Pull up on the latch plate to make sure it is secure. If the belt is not long enough, see Safety Belt Extender on page 2 ‑ 32 . Position the release button on the buckle so that the safety belt could be quickly unbuckled if necessary . 5. If equipped with a shoulder belt height adjuster , move it to the height that is right for you. See “ Shoulder Belt Height Adjustment ” later in this section for instructions on use and important safety information. 6. T o make the lap part tight, pull up on the shoulder belt. It may be necessary to [...]

T o unlatch the belt, push the button on the buckle. The belt should return to its stowed position. Before a door is closed, be sure the belt is out of the way . If a door is slammed against a safety belt, damage can occur to both the safety belt and the vehicle. Shoulder Belt Height Adjuster The vehicle has a shoulder belt height adjuster for the driver and right front passenger seating positions. Adjust the height so that the shoulder portion of the belt is centered on the shoulder . The belt should be away from the face and neck, but not falling off the shoulder . Improper shoulder belt height adjustment could reduce the effectiveness of the safety belt in a crash. T o move it down, press[...]

Safety Belt Pretensioners This vehicle has safety belt pretensioners for front outboard occupants. Although the safety belt pretensioners cannot be seen, they are part of the safety belt assembly . They can help tighten the safety belts during the early stages of a moderate to severe frontal or near frontal crash if the threshold conditions for pretensioner activation are met. Pretensioners work only once. If the pretensioners activate in a crash, they will need to be replaced, and probably other new parts for the vehicle's safety belt system. See Replacing Restraint System Parts After a Crash on page 2 ‑ 73 . Safety Belt Use During Pregnancy Safety belts work for everyone, including [...]

Safety Belt Extender If the vehicle's safety belt will fasten around you, you should use it. But if a safety belt is not long enough, your dealer/ retailer will order you an extender . When you go in to order it, take the heaviest coat you will wear , so the extender will be long enough for you. T o help avoid personal injury , do not let someone else use it, and use it only for the seat it is made to fit. The extender has been designed for adults. Never use it for securing child seats. T o wear it, attach it to the regular safety belt. For more information, see the instruction sheet that comes with the extender . Child Restraints Older Children Older children who have outgrown booster [...]

. Buckle the lap-shoulder belt. Does the shoulder belt rest on the shoulder? If yes, continue. If no, then return to the booster seat. . Does the lap belt fit low and snug on the hips, touching the thighs? If yes, continue. If no, return to the booster seat. . Can proper safety belt fit be maintained for the length of the trip? If yes, continue. If no, return to the booster seat. Q: What is the proper way to wear safety belts? A: An older child should wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide. The shoulder belt should not cross the face or neck. The lap belt should fit snugly below the hips, just touching the top of the thighs. This applies belt fo[...]

{ W ARNING: Never do this. Never allow a child to wear the safety belt with the shoulder belt behind their back. A child can be seriously injured by not wearing the lap-shoulder belt properly . In a crash, the child would not be restrained by the shoulder belt. The child could move too far forward increasing the chance of head and neck injury . The child might also slide under the lap belt. The belt force would then be applied right on the abdomen. That could cause serious or fatal injuries. The shoulder belt should go over the shoulder and across the chest. 2-34[...]

Infants and Y oung Children Everyone in a vehicle needs protection! This includes infants and all other children. Neither the distance traveled nor the age and size of the traveler changes the need, for everyone, to use safety restraints. In fact, the law in every state in the United States and in every Canadian province says children up to some age must be restrained while in a vehicle. { W ARNING: Children can be seriously injured or strangled if a shoulder belt is wrapped around their neck and the safety belt continues to tighten. Never leave children unattended in a vehicle and never allow children to play with the safety belts. Airbags plus lap ‐ shoulder belts offer protection for ad[...]

{ W ARNING: Never do this. Never hold an infant or a child while riding in a vehicle. Due to crash forces, an infant or a child will become so heavy it is not possible to hold it during a crash. For example, in a crash at only 40 km/h (25 mph), a 5.5 kg (12 lb) infant will suddenly become a 1 10 kg (240 lb) force on a person's arms. An infant should be secured in an appropriate restraint. 2-36[...]

{ W ARNING: Never do this. Children who are up against, or very close to, any airbag when it inflates can be seriously injured or killed. Never put a rear-facing child restraint in the right front seat. Secure a rear-facing child restraint in a rear seat. It is also better to secure a forward-facing child restraint in a rear seat. If you must secure a forward-facing child restraint in the right front seat, always move the front passenger seat as far back as it will go. 2-37[...]

Q: What are the different types of add-on child restraints? A: Add-on child restraints, which are purchased by the vehicle's owner , are available in four basic types. Selection of a particular restraint should take into consideration not only the child's weight, height, and age but also whether or not the restraint will be compatible with the motor vehicle in which it will be used. For most basic types of child restraints, there are many different models available. When purchasing a child restraint, be sure it is designed to be used in a motor vehicle. If it is, the restraint will have a label saying that it meets federal motor vehicle safety standards. The restraint manufacturer&[...]

{ W ARNING: A young child's hip bones are still so small that the vehicle's regular safety belt may not remain low on the hip bones, as it should. Instead, it may settle up around the child's abdomen. In a crash, the belt would apply force on a body area that is unprotected by any bony structure. This alone could cause serious or fatal injuries. T o reduce the risk of serious or fatal injuries during a crash, young children should always be secured in appropriate child restraints. Child Restraint Systems A rear-facing infant seat (A) provides restraint with the seating surface against the back of the infant. The harness system holds the infant in place and, in a crash, acts to[...]

A booster seat (C-D) is a child restraint designed to improve the fit of the vehicle's safety belt system. A booster seat can also help a child to see out the window . Securing an Add-On Child Restraint in the V ehicle { W ARNING: A child can be seriously injured or killed in a crash if the child restraint is not properly secured in the vehicle. Secure the child restraint properly in the vehicle using the vehicle's safety belt or LA TCH system, following the instructions that came with that child restraint and the instructions in this manual. T o help reduce the chance of injury , the child restraint must be secured in the vehicle. Child restraint systems must be secured in vehicle[...]

When securing an add-on child restraint, refer to the instructions that come with the restraint which may be on the restraint itself or in a booklet, or both, and to this manual. The child restraint instructions are important, so if they are not available, obtain a replacement copy from the manufacturer . Keep in mind that an unsecured child restraint can move around in a collision or sudden stop and injure people in the vehicle. Be sure to properly secure any child restraint in the vehicle — even when no child is in it. Securing the Child Within the Child Restraint { W ARNING: A child can be seriously injured or killed in a crash if the child is not properly secured in the child restraint[...]

Where to Put the Restraint Accident statistics show that children are safer if they are restrained in the rear rather than the front seat. We recommend that children and child restraints be secured in a rear seat, including: an infant or a child riding in a rear-facing child restraint; a child riding in a forward-facing child seat; an older child riding in a booster seat; and children, who are large enough, using safety belts. A label on your sun visor says, “ Never put a rear-facing child seat in the front. ” This is because the risk to the rear-facing child is so great, if the airbag deploys. { W ARNING: A child in a rear-facing child restraint can be seriously injured or killed if the[...]

There are a couple of things you need to know about using child restraints in your rear seat: If you use a child restraint in the center rear seating position (A), the safety belts and the child restraint LA TCH anchors for the rear outside seating positions (B) will not be accessible. Therefore, you will not be able to secure child restraints or have passengers ride in the rear outside seating positions. If you use two child restraints (A) in the rear outside seating positions, the safety belt for the center rear seat position (B) will not be accessible. Therefore, you will not be able to secure a child restraint or have a passenger ride in the center rear seating position. Wherever you ins[...]

Lower Anchors and T ethers for Children (LA TCH) The LA TCH system holds a child restraint during driving or in a crash. This system is designed to make installation of a child restraint easier . The LA TCH system uses anchors in the vehicle and attachments on the child restraint that are made for use with the LA TCH system. Make sure that a LA TCH-compatible child restraint is properly installed using the anchors, or use the vehicle's safety belts to secure the restraint, following the instructions that came with that restraint, and also the instructions in this manual. When installing a child restraint with a top tether , you must also use either the lower anchors or the safety belts [...]

T op T ether Anchor A top tether (A, C) anchors the top of the child restraint to the vehicle. A top tether anchor is built into the vehicle. The top tether attachment (B) on the child restraint connects to the top tether anchor in the vehicle in order to reduce the forward movement and rotation of the child restraint during driving or in a crash. Y our child restraint may have a single tether (A) or a dual tether (C). Either will have a single attachment (B) to secure the top tether to the anchor . Some child restraints that have a top tether are designed for use with or without the top tether being attached. Others require the top tether always to be attached. In Canada, the law requires t[...]

T o assist you in locating the lower anchors, each seating position with lower anchors has two labels, near the crease between the seatback and the seat cushion. Hatchback models may have zippers over the lower anchor areas. If so, unzip the seat cover below the labels to access each lower anchor . T o assist you in locating the top tether anchors, the top tether anchor symbol is located on the cover . Sedan For sedan models, the top tether anchors are located under the covers behind the rear seat on the filler panel. Pull open the cover to access the top tether anchors. Be sure to use an anchor located on the same side of the vehicle as the seating position where the child restraint will be[...]

Hatchback For hatchback models, the top tether anchors (B) are located in the rear cargo area, attached to the back wall (A) of the vehicle. Squeeze and pull the front part of the plastic cover to access the top tether anchors. Remove the cargo shade before installing the top tether. The cargo shade should remain off while the top tether is in use. Be sure to use an anchor located on the same side of the vehicle as the seating position where the child restraint will be placed. Do not secure a child restraint in a position without a top tether anchor if a national or local law requires that the top tether be attached, or if the instructions that come with the child restraint say that the top [...]

Securing a Child Restraint Designed for the LA TCH System { W ARNING: If a LA TCH-type child restraint is not attached to anchors, the child restraint will not be able to protect the child correctly . In a crash, the child could be seriously injured or killed. Install a LA TCH-type child restraint properly using the anchors, or use the vehicle's safety belts to secure the restraint, following the instructions that came with the child restraint and the instructions in this manual. { W ARNING: Do not attach more than one child restraint to a single anchor . Attaching more than one child restraint to a single anchor could cause the anchor or attachment to come loose or even break during a [...]

Notice: Do not let the LA TCH attachments rub against the vehicle ’ s safety belts. This may damage these parts. If necessary , move buckled safety belts to avoid rubbing the LA TCH attachments. Do not fold the empty rear seat with a safety belt buckled. This could damage the safety belt or the seat. Unbuckle and return the safety belt to its stowed position, before folding the seat. 1. Attach and tighten the lower attachments to the lower anchors. If the child restraint does not have lower attachments or the desired seating position does not have lower anchors, secure the child restraint with the top tether and the safety belts. Refer to your child restraint manufacturer instructions and [...]

2. 5. Route and tighten the top tether according to your child restraint instructions and the following instructions: If the position you are using does not have a headrest or head restraint and you are using a single tether , route the tether over the seatback. If the position you are using does not have a headrest or head restraint and you are using a dual tether , route the tether over the seatback. If the position you are using has a headrest or head restraint and you are using a dual tether , route the tether under the headrest or head restraint and in between the headrest or head restraint posts. If the position you are using has an adjustable headrest or head restraint and you are usi[...]

Securing a Child Restraint in a Rear Seat Position When securing a child restraint in a rear seating position, study the instructions that came with your child restraint to make sure it is compatible with this vehicle. If your child restraint has the LA TCH system, see Lower Anchors and T ethers for Children (LA TCH) on page 2 ‑ 44 for how to install your child restraint using LA TCH. If you secure a child restraint using a safety belt and it uses a top tether , see Lower Anchors and T ethers for Children (LA TCH) on page 2 ‑ 44 for top tether anchor locations. Do not secure a child restraint in a position without a top tether anchor if a national or local law requires that the top tethe[...]

3. Push the latch plate into the buckle until it clicks. If you find that the latch plate will not go fully into the buckle, see if you are using the correct buckle. Make sure the release button is positioned so you would be able to unbuckle the safety belt quickly if necessary . 4. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. 2-52[...]

5. T o tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor . If you are using a forward-facing child restraint, you may find it helpful to use your knee to push down on the child restraint as you tighten the belt. 6. If your child restraint has a top tether , follow the child restraint manufacturer's instructions regarding the use of the top tether . See Lower Anchors and T ethers for Children (LA TCH) on page 2 ‑ 44 . 7. Push and pull the child restraint in different directions to be sure it is secure. T o remove the child restraint, unbuckle the vehicle ’[...]

A label on the sun visor says, “ Never put a rear-facing child seat in the front. ” This is because the risk to the rear-facing child is so great, if the airbag deploys. { W ARNING: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger airbag inflates. This is because the back of the rear-facing child restraint would be very close to the inflating airbag. A child in a forward-facing child restraint can be seriously injured or killed if the right front passenger airbag inflates and the passenger seat is in a forward position. Even if the passenger sensing system has turned off the right front passenger frontal airbag, no system is fail-sa[...]

In Canada, the law requires that forward-facing child restraints have a top tether , and that the tether be attached. Y ou will be using the lap-shoulder belt to secure the child restraint in this position. Follow the instructions that came with the child restraint. 1. Move the seat as far back as it will go before securing the forward-facing child restraint. When the passenger sensing system has turned off the right front passenger frontal airbag and seat-mounted side impact airbag (if equipped), the off indicator on the passenger airbag status indicator should light and stay lit when you start the vehicle. See Passenger Airbag Status Indicator on page 4 ‑ 26 . 2. Put the child restraint [...]

4. Push the latch plate into the buckle until it clicks. Position the release button on the buckle so that the safety belt could be quickly unbuckled if necessary . 5. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. 2-56[...]

6. T o tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor . If you are using a forward-facing child restraint, you may find it helpful to use your knee to push down on the child restraint as you tighten the belt. 7. Push and pull the child restraint in different directions to be sure it is secure. If the airbag or airbags are off, the off indicator in the passenger airbag status indicator will come on and stay on when the vehicle is started. If a child restraint has been installed and the off symbol is not lit, see “ If the On Indicator is Lit for a Child Restrai[...]

Airbag System The vehicle has the following airbags: . A frontal airbag for the driver . . A frontal airbag for the right front passenger . The vehicle may have the following airbags: . A seat-mounted side impact airbag for the driver . . A seat-mounted side impact airbag for the right front passenger . All of the airbags in your vehicle will have the word AIRBAG embossed in the trim or on an attached label near the deployment opening. For frontal airbags, the word AIRBAG will appear on the middle part of the steering wheel for the driver and on the instrument panel for the right front passenger . With seat-mounted side impact airbags, the word AIRBAG will appear on the side of the seatback [...]

{ W ARNING: Airbags inflate with great force, faster than the blink of an eye. Anyone who is up against, or very close to, any airbag when it inflates can be seriously injured or killed. Do not sit unnecessarily close to the airbag, as you would be if you were sitting on the edge of your seat or leaning forward. Safety belts help keep you in position before and during a crash. Always wear your safety belt, even with airbags. The driver should sit as far back as possible while still maintaining control of the vehicle. Occupants should not lean on or sleep against the door or side windows in seating positions with seat-mounted airbags. { W ARNING: Children who are up against, or very close to,[...]

Where Are the Airbags? The driver's frontal airbag is in the middle of the steering wheel. The right front passenger's frontal airbag is in the instrument panel on the passenger's side. 2-60[...]

Driver Side shown, Passenger Side similar If your vehicle has seat-mounted side impact airbags for the driver and right front passenger , they are in the side of the seatbacks closest to the door . { W ARNING: If something is between an occupant and an airbag, the airbag might not inflate properly or it might force the object into that person causing severe injury or even death. The path of an inflating airbag must be kept clear . Do not put anything between an occupant and an airbag, and do not attach or put anything on the steering wheel hub or on or near any other airbag covering. Do not use seat accessories that block the inflation path of a seat-mounted side impact airbag. 2-61[...]

When Should an Airbag Inflate? Frontal airbags are designed to inflate in moderate to severe frontal or near-frontal crashes to help reduce the potential for severe injuries mainly to the driver's or right front passenger's head and chest. However , they are only designed to inflate if the impact exceeds a predetermined deployment threshold. Deployment thresholds are used to predict how severe a crash is likely to be in time for the airbags to inflate and help restrain the occupants. Whether your frontal airbags will or should deploy is not based on how fast your vehicle is traveling. It depends largely on what you hit, the direction of the impact, and how quickly your vehicle slow[...]

Seat-mounted side impact airbags are not intended to inflate in frontal impacts, near-frontal impacts, rollovers, or rear impacts. A seat-mounted side impact airbag is intended to deploy on the side of the vehicle that is struck. In any particular crash, no one can say whether an airbag should have inflated simply because of the damage to a vehicle or because of what the repair costs were. For frontal airbags, inflation is determined by what the vehicle hits, the angle of the impact, and how quickly the vehicle slows down. For seat-mounted side impact airbags, deployment is determined by the location and severity of the side impact. What Makes an Airbag Inflate? In a deployment event, the se[...]

What Will Y ou See After an Airbag Inflates? After the frontal and seat-mounted side impact airbags inflate, they quickly deflate, so quickly that some people may not even realize the airbags inflated. Some components of the airbag module may be hot for several minutes. For location of the airbag modules, see What Makes an Airbag Inflate? on page 2 ‑ 63 . The parts of the airbag that come into contact with you may be warm, but not too hot to touch. There may be some smoke and dust coming from the vents in the deflated airbags. Airbag inflation does not prevent the driver from seeing out of the windshield or being able to steer the vehicle, nor does it prevent people from leaving the vehicl[...]

In many crashes severe enough to inflate the airbag, windshields are broken by vehicle deformation. Additional windshield breakage may also occur from the right front passenger airbag. . Airbags are designed to inflate only once. After an airbag inflates, you will need some new parts for the airbag system. If you do not get them, the airbag system will not be there to help protect you in another crash. A new system will include airbag modules and possibly other parts. The service manual for your vehicle covers the need to replace other parts. . The vehicle has a crash sensing and diagnostic module which records information after a crash. See V ehicle Data Recording and Privacy on page 8 ‑ [...]

The passenger sensing system will turn off the right front passenger frontal airbag and seat-mounted side impact airbag (if equipped) under certain conditions. The driver airbags are not affected by the passenger sensing system. The passenger sensing system works with sensors that are part of the right front passenger seat. The sensors are designed to detect the presence of a properly-seated occupant and determine if the right front passenger frontal airbag and seat-mounted side impact airbag (if equipped) should be enabled (may inflate) or not. According to accident statistics, children are safer when properly secured in a rear seat in the correct child restrain for their weight and size. W[...]

The passenger sensing system is designed to turn off the right front passenger frontal airbag and seat-mounted side impact airbag (if equipped) if: . The right front passenger seat is unoccupied. . The system determines that an infant is present in a child restraint. . A right front passenger takes his/her weight off of the seat for a period of time. . Or , if there is a critical problem with the airbag system or the passenger sensing system. When the passenger sensing system has turned off the right front passenger frontal airbag and seat-mounted side impact airbag (if equipped), the off indicator will light and stay lit to remind you that the airbag or airbags are off. See Passenger Airbag[...]

If the On Indicator is Lit for a Child Restraint If a child restraint has been installed and the on indicator is lit: 1. T urn the vehicle off. 2. Remove the child restraint from the vehicle. 3. Remove any additional items from the seat such as blankets, cushions, seat covers, seat heaters, or seat massagers. 4. Reinstall the child restraint following the directions provided by the child restraint manufacturer and refer to Securing a Child Restraint in the Right Front Seat Position on page 2 ‑ 53 . 5. If, after reinstalling the child restraint and restarting the vehicle, the on indicator is still lit, turn the vehicle off. Then slightly recline the vehicle seatback and adjust the seat cush[...]

If the Off Indicator is Lit for an Adult ‐ Size Occupant If a person of adult-size is sitting in the right front passenger seat, but the off indicator is lit, it could be because that person is not sitting properly in the seat. If this happens, use the following steps to allow the system to detect that person and enable the right front passenger frontal airbag and seat-mounted side impact airbag (if equipped): 1. T urn the vehicle off. 2. Remove any additional material from the seat, such as blankets, cushions, seat covers, seat heaters, or seat massagers. 3. Place the seatback in the fully upright position. 4. Have the person sit upright in the seat, centered on the seat cushion, with leg[...]

Additional Factors Affecting System Operation Safety belts help keep the passenger in position on the seat during vehicle maneuvers and braking, which helps the passenger sensing system maintain the passenger airbag status. See “ Safety Belts ” and “ Child Restraints ” in the Index for additional information about the importance of proper restraint use. A thick layer of additional material, such as a blanket or cushion, or aftermarket equipment such as seat covers, seat heaters, and seat massagers can affect how well the passenger sensing system operates. We recommend that you not use seat covers or other aftermarket equipment other than any that GM has approved for your specific veh[...]

Adding Equipment to Y our Airbag-Equipped V ehicle Q: Is there anything I might add to or change about the vehicle that could keep the airbags from working properly? A: Y es. If you add things that change your vehicle's frame, bumper system, height, front end or side sheet metal, they may keep the airbag system from working properly . Changing or moving any parts of the front seats, safety belts, the airbag sensing and diagnostic module, steering wheel, instrument panel, front sensors, or airbag wiring can affect the operation of the airbag system. In addition, the vehicle has a passenger sensing system for the right front passenger position, which includes sensors that are part of the [...]

Restraint System Check Checking the Restraint Systems Safety Belts Now and then, check that the safety belt reminder light, safety belts, buckles, latch plates, retractors, and anchorages are all working properly . Look for any other loose or damaged safety belt system parts that might keep a safety belt system from doing its job. See your dealer/retailer to have it repaired. T orn or frayed safety belts may not protect you in a crash. They can rip apart under impact forces. If a belt is torn or frayed, get a new one right away . Make sure the safety belt reminder light is working. See Safety Belt Reminders on page 4 ‑ 24 for more information. Keep safety belts clean and dry . See Care of [...]

Replacing Restraint System Parts After a Crash { W ARNING: A crash can damage the restraint systems in your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash. T o help make sure your restraint systems are working properly after a crash, have them inspected and any necessary replacements made as soon as possible. If the vehicle has been in a crash, do you need new safety belts or LA TCH system (if equipped) parts? After a very minor crash, nothing may be necessary . But the safety belt assemblies that were used during any crash may have been stressed or damaged. See your dealer/retailer to have the safety bel[...]

2 NOTES 2-74[...]

Section 3 Features and Controls Keys ........................... ..................... 3-2 Remote Keyless Entry (RKE) System . . . . . . . . . . . 3-3 Remote Keyless Entry (RKE) System O p e r a t i o n ................... ............... ... 3 - 4 Doors and Locks ... ............................... 3-6 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6 Central Door Unlocking System . . . . . . . . . . . . . . . . . 3-7 Door Ajar Reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7 Rear Door Security Locks . . . . . . . . . . . . . . . . . . . . . . . 3-7 T r u n k ....................................... .... 3 - 8 Liftgate (Hatchback) [...]

Keys { W ARNING: Leaving children in a vehicle with the ignition key is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function with the keys in the ignition and children could be seriously injured or killed if caught in the path of a closing window . Do not leave the keys in a vehicle with children. The key can be used for the ignition, doors and all other locks. The key has a key code tag that the dealer/retailer or qualified locksmith can use to make new keys. Store this information in a safe place, not in your vehicle. 3-2[...]

Y our vehicle may have an electronic immobilizer designed to protect your car against theft. If so, only keys with the correct electronic code can be used to start the vehicle. See Immobilizer Operation on page 3 ‑ 14 for additional information. If a replacement key or an additional key is needed, it must be purchased from your dealer/retailer or certified locksmith. Notice: If you ever lock your keys in the vehicle, you may have to damage the vehicle to get in. Be sure you have spare keys. In an emergency , contact Roadside Assistance. See Roadside Assistance Program on page 8 ‑ 7 for more information. Remote Keyless Entry (RKE) System See Radio Frequency Statement on page 8 ‑ 20 for [...]

Remote Keyless Entry (RKE) System Operation The Remote Keyless Entry (RKE) transmitter functions work up to 65 feet (20 m) away from the vehicle. There are other conditions which can affect the performance of the transmitter . See Remote Keyless Entry (RKE) System on page 3 ‑ 3 . Hatchback Sedan The following functions may be available if the vehicle has RKE: Q (Lock): Press to lock all of the doors. If all of the doors and the trunk or liftgate are closed, the hazard lamps flash once and the horn will sound to indicate that locking has occurred and the theft-deterrent system is active. K (Unlock): Press to unlock all of the doors. The hazard lamps flash twice to indicate that unlocking ha[...]

Programming T ransmitters to the V ehicle Only RKE transmitters programmed to the vehicle will work. If a transmitter is lost or stolen, a replacement can be purchased and programmed through your dealer/retailer . When the replacement transmitter is programmed to the vehicle, all remaining transmitters must also be programmed. Any lost or stolen transmitters no longer work once the new transmitter is programmed. Each vehicle can have up to five transmitters programmed to it. Battery Replacement Replace the battery if the LED on the transmitter does not flash when you press the buttons. Notice: When replacing the battery , do not touch any of the circuitry on the transmitter. Static from your[...]

Doors and Locks Door Locks { W ARNING: Unlocked doors can be dangerous. . Passengers, especially children, can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. The chance of being thrown out of the vehicle in a crash is increased if the doors are not locked. So, all passengers should wear safety belts properly and the doors should be locked whenever the vehicle is driven. . Y oung children who get into unlocked vehicles may be unable to get out. A child can be overcome by extreme heat and can suffer permanent injuries or even death from heat stroke. Always lock the vehicle whenever leaving it. (Continued) W ARNING: (Continued) . Outs[...]

Central Door Unlocking System The vehicle may be equipped with the central door unlocking system. This system is activated from the driver door . From the outside, lock or unlock all the doors by using either the key or the RKE transmitter , if equipped. From the inside, lock or unlock all the doors by using the driver door lock switch. Door Ajar Reminder If one of the doors, trunk, or liftgate is not closed properly while the ignition is on, the door ajar light on the instrument panel comes on and stays on until the doors are closed. Rear Door Security Locks The vehicle has rear door security locks on each rear door that prevents passengers from opening the rear doors from the inside. Using[...]

Opening a Rear Door When the Security Lock is On 1. Unlock the door from the inside. 2. Open the door from the outside. If you do not cancel the security lock, adults or older children who ride in the rear will not be able to open the rear door from the inside. Canceling the Rear Door Security Lock 1. Unlock the door from the inside and open the door from the outside. 2. Move the lever down to unlock. 3. Repeat Steps 1 and 2 to the other rear door lock. The rear door locks can now be locked and unlocked normally . T runk { W ARNING: Exhaust gases can enter the vehicle if it is driven with the liftgate, trunk/hatch open, or with any objects that pass through the seal between the body and the [...]

T o open the trunk on a sedan from outside of the vehicle, insert the key into the lock cylinder and turn the key clockwise or use the RKE transmitter , if equipped. See Remote Keyless Entry (RKE) System Operation on page 3 ‑ 4 . Remote T runk Release This feature allows the trunk to be opened from inside the vehicle. the vehicle may have either a release button or a release lever . The vehicle may have a release button located on the driver door . Press it to open the trunk. The vehicle may have a trunk release lever located on the outboard side of the driver seat. Pull the lever to open the trunk. When closing the trunk, close from the center to ensure it fully latches. 3-9[...]

Emergency T runk Release Handle Notice: Do not use the emergency trunk release handle as a tie-down or anchor point when securing items in the trunk as it could damage the handle. The emergency trunk release handle is only intended to aid a person trapped in a latched trunk, enabling them to open the trunk from the inside. There is a glow-in-the-dark emergency trunk release handle located on the underside of the trunk lid. This handle will glow following exposure to light. Pull the release handle down to open the trunk from the inside. Liftgate (Hatchback) { W ARNING: Exhaust gases can enter the vehicle if it is driven with the liftgate, trunk/hatch open, or with any objects that pass throug[...]

W ARNING: (Continued) . Adjust the Climate Control system to a setting that brings in only outside air and set the fan speed to the highest setting. See Climate Control System in the Index. . If the vehicle is equipped with a power liftgate, disable the power liftgate function. For more information about carbon monoxide, see Engine Exhaust on page 3 ‑ 32 . T o unlock the liftgate on a hatchback from outside of the vehicle, insert the key in the lock cylinder and turn it counterclockwise or use the RKE transmitter , if equipped. The handle is located above the right side of the license plate. Pull the handle toward you and raise the liftgate. When closing the liftgate, close from the center[...]

Windows { W ARNING: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather. 3-12[...]

Manual Windows Use the window crank to open and close each window . The rear windows do not open fully . Power Windows { W ARNING: Leaving children in a vehicle with the keys is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function and they could be seriously injured or killed if caught in the path of a closing window . Do not leave keys in a vehicle with children. When there are children in the rear seat use the window lockout button to prevent unintentional operation of the windows. On vehicles with power windows, the switches are located on the dr[...]

Window Lockout The window lockout is located with the driver power window switches. Press the lockout button to stop the rear passengers from using the rear window switches. The driver can still operate all the windows with the lockout on. Press the lockout button again to return to normal window operation. Sun Visors T o block out glare you can swing down the sun visors. Y ou can also remove them from the center mount and swing them to the side. Visor V anity Mirror The vehicle has vanity mirrors located on the back of the sun visors. Swing down the sun visor to expose the vanity mirror . Theft-Deterrent Systems V ehicle theft is big business, especially in some cities. This vehicle has the[...]

Y our vehicle has a special key that works with the theft-deterrent system. There is a transponder in the key head that is electronically coded. The correct key will start the vehicle. An invalid key immobilizes the engine. If your key is ever damaged, you may not be able to start your vehicle. When trying to start the vehicle, if the engine does not start and the security light flashes or comes on, there may be a problem with the theft-deterrent system. Turn the ignition off and try again. If the engine still does not start, and the key appears to be undamaged, try another key . At this time, you may also want to check the fuse. See Fuses and Circuit Breakers on page 6 ‑ 87 . If the engin[...]

Arming the System T o arm the system, do the following: 1. Close the doors, the windows, the hood, and the trunk or liftgate. Make sure that the windows are closed, as the system can be armed even if the windows are open. 2. T urn the key to LOCK/OFF and remove the key from the ignition. If the key is inserted in the ignition, the transmitter will not arm the theft-deterrent system. 3. Lock the doors by pressing the lock button on the remote keyless entry transmitter . . The LED light on the transmitter will flash once. . All of the doors will lock. . The hazard warning lamps will flash once and the horn will sound. . The security light will flash continuously to indicate that the theft-dete[...]

How the System Alarm is Activated If a door or the trunk or liftgate is opened without using the key or the remote keyless entry transmitter , the horn will sound and the lamps will flash for up to 30 seconds. How to T urn Off the System Alarm If the system alarm is active, it can be deactivated using one of the following methods: . Press one of the buttons on the remote keyless entry transmitter . . Unlock the driver's or passenger's front door using the key . Otherwise, the alarm will automatically stop after 30 seconds. The system will then lock the doors and rearm the theft-deterrent system. How to Detect a T amper Condition If the hazard warning lamps flash once when you press[...]

Ignition Positions The ignition switch has four different positions. { W ARNING: On manual transmission vehicles, turning the key to LOCK/OFF will lock the steering column and result in a loss of ability to steer the vehicle. This could cause a collision. If you need to turn the engine off while the vehicle is moving, turn the key only to ACC/ACCESSORY . Do not push the key in while the vehicle is moving. Notice: Using a tool to force the key to turn in the ignition could cause damage to the switch or break the key . Use the correct key , make sure it is all the way in, and turn it only with your hand. If the key cannot be turned by hand, see your dealer/retailer . LOCK/OFF: This position lo[...]

Starting the Engine Automatic T ransmission Move the shift lever to P (Park) or N (Neutral). The engine will not start in any other position. T o restart the engine when the vehicle is already moving, use N (Neutral) only . Notice: Do not try to shift to P (Park) if the vehicle is moving. If you do, you could damage the transmission. Shift to P (Park) only when the vehicle is stopped. Manual T ransmission The shift lever should be in N (Neutral) and the parking brake engaged. Hold the clutch pedal to the floor and start the engine. The vehicle will not start if the clutch pedal is not all the way down. Starting Procedure 1. With your foot off the accelerator pedal, turn the ignition to ST AR[...]

3. If the engine still will not start, or starts but then stops, it could be flooded with too much gasoline. T ry pushing the accelerator pedal all the way to the floor and holding it there as you hold the key in ST ART for about three seconds. If the vehicle starts briefly but then stops again, do the same thing, but this time keep the pedal down for five or six seconds. This clears the extra gasoline from the engine. Notice: The engine is designed to work with the electronics in the vehicle. If electrical parts or accessories are added, you could change the way the engine operates. Before adding electrical equipment, check with your dealer/retailer . If you do not, the engine might not per[...]

{ W ARNING: Plugging the cord into an ungrounded outlet could cause an electrical shock. Also, the wrong kind of extension cord could overheat and cause a fire. Y ou could be seriously injured. Plug the cord into a properly grounded three-prong 1 10-volt AC outlet. If the cord will not reach, use a heavy-duty three-prong extension cord rated for at least 15 amps. 4. Before starting the engine, be sure to unplug both the extension cord and under hood electrical cord, and store them as they were before. This will keep them away from moving engine parts, and prevent damage. The length of time the heater should remain plugged in depends on several factors. Ask a dealer/retailer in the area where[...]

Attached Extension Cord 1. T urn off the engine. 2. Open the hood and unwrap the electrical cord. The cord is located in the driver side of the engine compartment, near the battery . 3. Plug it into a normal, grounded 1 10-V olt AC outlet. { W ARNING: Plugging the cord into an ungrounded outlet could cause an electrical shock. Also, the wrong kind of extension cord could overheat and cause a fire. Y ou could be seriously injured. Plug the cord into a properly grounded three-prong 1 10-volt AC outlet. If the cord will not reach, use a heavy-duty three-prong extension cord rated for at least 15 amps. 4. Before starting the engine, be sure to unplug and store the cord as it was before to keep i[...]

Automatic T ransmission Operation If the vehicle has an automatic transmission, the shift lever is located on the console between the seats. Movement between certain positions requires pushing the release button on the front of the shifter . P (Park): This position locks the front wheels. It is the best position to use when you start the engine because the vehicle cannot move easily . { W ARNING: It is dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake firmly set. The vehicle can roll. Do not leave the vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly . Y ou or others c[...]

R (Reverse): Use this gear to back up. When shifting from N (Neutral) to R (Reverse), you need to apply the brake pedal and push the release button on the front of the shifter . Notice: Shifting to R (Reverse) while the vehicle is moving forward could damage the transmission. The repairs would not be covered by the vehicle warranty . Shift to R (Reverse) only after the vehicle is stopped. T o rock the vehicle back and forth to get out of snow , ice or sand without damaging the transmission, see If Y our Vehicle is Stuck in Sand, Mud, Ice, or Snow on page 5 ‑ 14 . N (Neutral): In this position, the engine does not connect with the wheels. T o restart the engine while the vehicle is already [...]

Notice: Do not drive in 2 (Second) at speeds over 65 mph (105 km/h), or you can damage the transmission. Use D4 (Automatic Overdrive) as much as possible. Do not shift into 2 (Second) unless you are going slower than 65 mph (105 km/h) or you can damage the engine. 1 (First): This position gives you even more power but lower fuel economy than 2 (Second). Y ou can use it on very steep hills, or in deep snow or mud. If the shift lever is put in 1 (First), the transmission will not shift into first gear until the vehicle is going slowly enough. Notice: Spinning the tires or holding the vehicle in one place on a hill using only the accelerator pedal may damage the transmission. The repair will no[...]

When hold mode is activated, the transmission runs as follows: Selector Lever Position Gear Range D4 Third Gear 2 Second Gear 1 First Gear See Hold Mode Light on page 4 ‑ 29 . When Hold Mode is selected in D4 (Drive), the transmission is held in 3 (Third) gear, which locks out D4 (Drive). This allows for engine braking when slowing from higher speeds. When Hold Mode is selected in 2 (Second), the transmission will start in 2 (Second) gear instead of 1 (First), helping to reduce wheel spin when starting out on slippery surface such as snow , mud or ice. Since selecting Hold Mode in D4 (Drive) locks the transmission in 3 (Third), and prevents downshifts to 2 (Second) or 1 (First), accelerati[...]

2 (Second): Press the clutch pedal as you let up on the accelerator pedal and shift into 2 (Second). Then, slowly let up on the clutch pedal as you press the accelerator pedal. 3 (Third), 4 (Fourth) and 5 (Fifth): Shift into 3 (Third), 4 (Fourth) and 5 (Fifth), the same way you do for 2 (Second). Slowly let up on the clutch pedal as you press the accelerator pedal. T o stop, let up on the accelerator pedal and press the brake pedal. Just before the vehicle stops, press the clutch pedal and the brake pedal, and shift to N (Neutral). N (Neutral): Use this position when you start or idle the engine. R (Reverse): T o back up, press down the clutch pedal, lift up the ring on the shift lever and s[...]

Parking Brake The parking brake lever is located between the bucket seats. T o set the parking brake, hold the brake pedal down and pull up on the parking brake lever . If the ignition is on, the brake system warning light will come on. See Brake System Warning Light on page 4 ‑ 28 . T o release the parking brake, hold the brake pedal down. Pull the parking brake lever up until you can press the release button. Hold the release button in as you move the brake lever all the way down. Notice: Driving with the parking brake on can overheat the brake system and cause premature wear or damage to brake system parts. Make sure that the parking brake is fully released and the brake warning light i[...]

3. T urn the ignition key to LOCK/OFF . 4. Remove the key and take it with you. If you can leave the vehicle with the ignition key in your hand, the vehicle is in P (Park). Leaving the V ehicle With the Engine Running (Automatic T ransmission) { W ARNING: It can be dangerous to leave the vehicle with the engine running. The vehicle could move suddenly if the shift lever is not fully in P (Park) with the parking brake firmly set. And, if you leave the vehicle with the engine running, it could overheat and even catch fire. Y ou or others could be injured. Do not leave the vehicle with the engine running. If you have to leave the vehicle with the engine running, be sure the vehicle is in P (Par[...]

Shifting Out of Park V ehicles with an automatic transmission have a shift interlock system. Y ou have to apply the brake pedal before you can shift from P (Park) when the ignition is in the ON/RUN position. See Automatic T ransmission Operation on page 3 ‑ 23 . If you cannot shift out of P (Park) while holding the brake pedal down, try this: 1. Set the parking brake. 2. T urn the ignition off and remove the key . 3. Remove the hole cover from the shift lock slot by prying it off using a small, flat object. The shift lock release slot is located at the top of the shift lever . 4. Insert the key into the shift lock slot and press and hold the key . 5. Shift to N (Neutral). 6. Remove the key[...]

Parking the V ehicle (Manual T ransmission) Before leaving the vehicle, do the following: 1. Hold the brake pedal down and firmly apply the parking brake. 2. Fully press in the clutch pedal and place the shift lever into the gear position as stated below: . When parking on level ground, place the shift lever into N (Neutral). . When parking downhill, place the shift lever in R (Reverse). . When parking uphill, place the shift lever in 1 (First). 3. After shifting, turn the ignition to LOCK/OFF , remove the key and release the clutch. Parking Over Things That Burn { W ARNING: Things that can burn could touch hot exhaust parts under the vehicle and ignite. Do not park over papers, leaves, dry [...]

Engine Exhaust { W ARNING: Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. Exposure to CO can cause unconsciousness and even death. Exhaust may enter the vehicle if: . The vehicle idles in areas with poor ventilation (parking garages, tunnels, deep snow that may block underbody airflow or tail pipes). . The exhaust smells or sounds strange or different. . The exhaust system leaks due to corrosion or damage. (Continued) W ARNING: (Continued) . The vehicle ’ s exhaust system has been modified, damaged or improperly repaired. . There are holes or openings in the vehicle body from damage or after-market modifications that are not completely sealed. If unusual fume[...]

Running the V ehicle While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know . { W ARNING: Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle. Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death. Never run the engine in an enclosed area that has no fresh air ventilation. For more information, see Engine Exhaust on page 3 ‑ 32 . { W ARNING: It can be dangerous to get out of the vehicle if the automatic transmission shift lever is not fully in P (Park) with the parking brake firmly set. The vehicle can ro[...]

Mirrors Manual Rearview Mirror Hold the inside rearview mirror in the center to move it for a clearer view behind your vehicle. Adjust the mirror to avoid glare from the headlamps behind you. Push the tab forward for daytime use and pull it for nighttime use. Outside Manual Mirrors Adjust the mirrors to see a little of the side of your vehicle. Controls for the outside manual mirrors are located next to each mirror . Manually fold the mirrors inward to prevent damage when going through an automatic car wash. T o fold, push the mirror toward the vehicle. Push the mirror outward, to return it to the original position. 3-34[...]

Outside Power Mirrors The control is located on the instrument panel, left of the steering wheel. The ignition must be turned to ON/RUN to adjust the mirrors. T o adjust the mirrors: 1. Select the mirror you want to adjust by moving the selector switch to L for the driver side mirror or R for the passenger side mirror. 2. Press one of the four arrows located on the control pad to move the mirror to the desired direction. Manually fold the mirrors inward to prevent damage when going through an automatic car wash. T o fold, push the mirror toward the vehicle. Push the mirror outward, to return to its original position. Outside Convex Mirror { W ARNING: A convex mirror can make things, like oth[...]

Storage Areas The vehicle may have shopping bag hooks on each front seatback. Lift the headrest to access the hooks. Glove Box Lift up on the glove box lever to open it. Cupholders T wo cupholders are located in the center instrument panel, below the climate control system. T o use the cupholder , push in on the cover , then pull it out. After use, push in the cupholder until it latches. There is also a cupholder located in the rear of the center console. 3-36[...]

Sunroof On vehicles with this feature, the switch is located on the headliner between the sun visors. The sunroof only operates when the ignition is turned to ON/RUN. The sunroof can be opened to a vent position or it can be opened all of the way . T o open the sunroof to the vent position, open the sunshade. Then press and hold the driver side of the switch. T o close the sunroof, press and hold the passenger side of the switch until the sunroof reaches the desired position. T o fully open the sunroof, press and hold the passenger side of the switch. The sunshade opens with the sunroof. T o close the sunroof, press and hold the driver side of the switch. The sunroof will stop if the switch [...]

2 NOTES 3-38[...]

Section 4 Instrument Panel Instrument Panel Overview ............... ......... 4-3 Hazard W arning Flashers . . . . . . . . . . . . . . . . . . . . . . . 4-3 Horn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 T ilt Wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 T urn Signal/Multifunction Lever . . . . . . . . . . . . . . . . . . 4-4 T urn and Lane-Change Signals . . . . . . . . . . . . . . . . . 4-4 Headlamp High/Low-Beam Changer . . . . . . . . . . . . 4-5 Flash-to-Pass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 Windshield Wipers . . . . . . . . . . . . . . . . . . . . . . .[...]

Section 4 Instrument Panel T rip Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-38 Audio System(s) ................. ............. .... 4-39 A M - F M R a d i o ................................. . 4 - 4 0 Radio with CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-45 Radio with Six-Disc CD . . . . . . . . . . . . . . . . . . . . . . . . 4-53 Using an MP3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-61 XM Radio Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-63 Audio Steering Wheel Controls . . . . . . . . . . . . . . . . 4-64 R a d i o R e c e p t i o n .................... ........... 4 - 6 5 F[...]

Instrument Panel Overview Hazard W arning Flashers The hazard warning flasher button is located to the right of the climate control system on the sedan. | Hazard W arning Flasher: Press to make the front and rear turn signal lamps flash on and off. This warns others that you are having trouble. Press the button again to turn the flashers off. When the hazard warning flashers are on, the turn signals will not work. Horn Press near or on the horn symbols on the steering wheel pad to sound the horn. Tilt Wheel The tilt wheel lever is located under the steering column, slightly to the left. T o adjust the steering wheel: 1. Pull the lever down. 2. Move the steering wheel up or down into a comfor[...]

T urn Signal/Multifunction Lever The lever on the left side of the steering column includes the following: G : T urn and Lane-Change Signals 3 : Headlamp High/Low-Beam Changer P : Exterior Light Control # : Fog Lamps, if equipped Flash-to-Pass Feature. Information for these features is on the pages following. T urn and Lane-Change Signals An arrow on the instrument panel cluster flashes in the direction of the turn or lane change. Move the lever all the way up or down to signal a turn. 4-4[...]

Raise or lower the lever until the arrow starts to flash to signal a lane change. Hold it there until the lane change is completed. The lever returns to its starting position whenever it is released. If after signaling a turn or a lane change the arrow flashes rapidly or does not come on, a signal bulb may be burned out. Have the bulbs replaced. If the bulb is not burned out, check the fuse. See Fuses and Circuit Breakers on page 6 ‑ 87 . Headlamp High/Low-Beam Changer The headlamps must be on for this feature to work. Push the turn signal lever away from you to turn the high beams on. This instrument panel cluster light 3 comes on while the high beams are on and the ignition is turned to [...]

Windshield Wipers Sedan shown Hatchback shown The lever is located on the right side of the steering column. The ignition must be turned to ON/RUN to operate the windshield wipers. Move the lever to one of the following positions: HI (High Speed): Fast wipes. LO (Low Speed): Slow wipes. INT (Intermittent): Move to this position for a delayed wiping cycle. Turn the band on the windshield wiper toward F AST or SLOW for a shorter or longer delay between wipes. The wiper speed can only be adjusted when the lever is in the INT position. OFF: Turns the windshield wipers of f. 4-6[...]

Misting Function Move the lever toward INT for a single wiping cycle. Hold it there until the windshield wipers start; then let go. The windshield wipers will stop after one wipe. If more wipes are needed, hold the band toward INT longer . Clear ice and snow from the wiper blades before using them. If frozen to the windshield, carefully loosen or thaw them. Damaged wiper blades should be replaced. See Windshield Wiper Blade Replacement on page 6 ‑ 50 . Heavy snow or ice can overload the wipers. A circuit breaker stops them until the motor cools. Windshield W asher T o use this feature, the ignition must be turned to ON/RUN. Pull the windshield washer/wiper lever toward you to spray washer [...]

Rear Window Wiper/W asher { W ARNING: In freezing weather , do not use your washer until the windshield is warmed. Otherwise the washer fluid can form ice on the windshield, blocking your vision. The vehicle may have a rear window wiper/washer . T urn the rear wiper/washer band to operate the rear window wiper/washer . OFF: Turns the rear window wiper/washer off. Z : Turns the rear wiper on for intermittent wipes. Y : Sprays washer fluid onto the rear window and the wiper operates continuously . The windshield washer reservoir is used for the windshield and rear window . Check the fluid level if either washer is not working. See Windshield Washer Fluid on page 6 ‑ 33 . Cruise Control For v[...]

The cruise control buttons are located on the right side of the steering wheel. I / O (On/Off): Press to turn the cruise control on or off. RES+ (Resume/Accelerate): Press to make the vehicle accelerate or resume to a previously set speed. SET − (Set/Coast): Press to set the speed or make the vehicle decelerate. Setting Cruise Control { W ARNING: If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. Y ou could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control. 1. Press I / O to turn cruise control on. 2. Accelerate to the speed desired. 3. Press the SET ?[...]

Resuming a Set Speed If the cruise control is set to a desired speed and then the brakes are applied, or the clutch pedal if you have a manual transmission, the cruise control shuts off. But it does not need to be reset. Once the vehicle is going about 39 km/h (24 mph) or more, briefly press the RES+ button. The vehicle returns to the previously set speed and stays there. If the RES+ button is held, the vehicle speed will continue to increase until the button is released or the brake pedal is applied. Do not hold in the RES+ button, unless you want the vehicle to go faster . Increasing Speed While Using Cruise Control There are two ways to go to a higher speed. . Use the accelerator pedal to[...]

Ending Cruise Control There are two ways to turn off the cruise control: . Step lightly on the brake pedal, or press the clutch pedal, if you have a manual transmission. . Press I / O on the cruise control pad. Erasing Speed Memory The cruise control set speed memory is erased when the cruise control or the ignition is turned off. Exterior Lamps Uplevel shown, Base similar The lever on the left side of the steering column operates the exterior lamps. The exterior lamp band has three positions: 3 (Headlamps): T urns on the headlamps, together with the following: . T aillamps . License Plate Lamp . Instrument Panel Lights . Parking Lamps The headlamps automatically turn off when the ignition k[...]

Daytime Running Lamps (DRL) Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day . Fully functional daytime running lamps are required on all vehicles first sold in Canada. The DRL system makes the headlamps come on when the following conditions are met: . The ignition is on. . The exterior lamp band is in OFF or in the parking lamp position. . The parking brake is released. An indicator light on instrument panel cluster comes on when the DRL system is on. When the DRL system is on, the taillamps, sidemarker lamps, parking lamps and instrument panel lights do not come on unless the exterior lamps control is turned to the parking lamp or he[...]

Instrument Panel Brightness This feature controls the brightness of the instrument panel lights. The thumbwheel for this feature is located on the instrument panel to the left of the steering column. Turn the thumbwheel to brighten or dim the lights. Dome Lamp The vehicle has a dome lamp located in the overhead console. Move the switch to the following positions: ON: The light comes on and stays on. O (Door): The light comes on when a door is opened. The light turns off when all the doors are closed. OFF: The light remains off even when a door is opened. Be sure all doors and trunk lid or hatch are completely closed or the battery may drain. Inadvertent Power Battery Saver This feature is de[...]

Accessory Power Outlet(s) Accessory power outlets can be used to plug in auxiliary electrical equipment, such as a cellular phone. The accessory power outlet is located next to the parking brake on the center console. T o use the accessory power outlet, remove the protective cap. When not in use, always cover the outlet with the protective cap. The accessory power outlet is operational when the ignition is turned to ACC/ ACCESSORY or ON/RUN. Notice: Leaving electrical equipment on for extended periods will drain the battery . Always turn off electrical equipment when not in use and do not plug in equipment that exceeds the maximum amperage rating. Certain electrical accessories may not be co[...]

Ashtray(s) and Cigarette Lighter The ashtray is located at the lower part of the center instrument panel. T o remove the front ashtray for cleaning, open the ashtray fully , press in the retaining tab and pull the bin out. Notice: If papers, pins, or other flammable items are put in the ashtray , hot cigarettes or other smoking materials could ignite them and possibly damage the vehicle. Never put flammable items in the ashtray . The cigarette lighter is located to the right of the front ashtray . T o use it, turn the ignition to ACC/ACCESSORY or ON/RUN, push the cigarette lighter in all the way and let go. When it is ready , it will pop back out. Electrical accessories may not be compatible[...]

Climate Controls Climate Control System For vehicles with these climate control systems, the heating, cooling, and ventilation can be controlled for the vehicle. Climate Control System with Heater and Air Conditioning A. T emperature Control B. Fan Control C. Air Delivery Mode Control D. Air Conditioning (A/C) E. Recirculation F . Rear Window Defogger Climate Control System with Heater Only A. T emperature Control B. Fan Control C. Air Delivery Mode Control D. Rear Window Defogger E. Outside Air/ Recirculation 4-16[...]

OFF: Turns the fan off. T emperature Control: T urn clockwise or counterclockwise to increase or decrease the temperature of the air flowing from the system. 9 (Fan Control): Turn clockwise or counterclockwise to increase or decrease the fan speed. The fan must be turned on to run the air conditioning compressor . Air Delivery Mode Control: T urn clockwise or counterclockwise to change the current airflow mode. Select from the following air delivery modes: Y (V ent): Air is directed to the instrument panel outlets. (Bi-Level): Air is divided between the instrument panel and floor outlets. [ (Floor): Air is directed to the floor outlets, with some air directed to the rear outlets. Keep the [...]

For quick cool down on hot days, do the following: 1. Open the windows to let hot air escape. 2. Press ? . 3. Press A/C. 4. Select the coolest temperature. 5. Select the highest 9 speed. Using these settings together for long periods of time may cause the air inside of the vehicle to become too dry . T o prevent this from happening, after the air in the vehicle has cooled, turn the recirculation mode off. The air conditioning system removes moisture from the air , so a small amount of water might drip under the vehicle while idling or after turning off the engine. This is normal. ? (Recirculation): This mode recirculates and helps to quickly cool the air inside the vehicle. It can be used to[...]

Rear Window and Outside Mirror Defogger For vehicles with a rear window and outside mirror defogger , they only work when the ignition is turned to ON/RUN. The rear window defogger uses a warming grid to remove fog or frost from the rear window . < (Rear Window Defogger): Press to turn the rear window and outside mirror defogger on or off. An indicator light comes on to show that the feature is on. If the vehicle does not have air conditioning, the rear window defogger may turn off about 10 minutes after the button is pressed. If it remains on, it can be turned off by pressing < again or by turning off the engine. If the vehicle has air conditioning, the rear window defogger turns off [...]

T o change the passenger compartment air filter , use the following steps: 1. Open the glove box halfway down. 2. Grip the glove box by both the upper and lower sides and pull it out of its housing. 3. Remove the filter cover by pressing in on the bottom retaining tab and pulling the cover down. 4-20[...]

4. Replace the air conditioner filter . 5. View the air flow arrows on the filter before installing to ensure the filter is installed correctly . W arning Lights, Gauges, and Indicators W arning lights and gauges can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement. Paying attention to the warning lights and gauges could prevent injury . W arning lights come on when there might be or there is a problem with one of the vehicle's functions. Some warning lights come on briefly when the engine is started to indicate they are working. Gauges can indicate when there might be or there is a problem with one of the vehicle's functio[...]

Instrument Panel Cluster United States Manual T ransmission shown, Canada and Automatic T ransmission Similar 4-22[...]

Speedometer and Odometer The speedometer shows the vehicle's speed in both kilometers per hour (km/h) and miles per hour (mph). The odometer shows how far the vehicle has been driven, in either kilometers (used in Canada) or miles (used in the United States). T rip Odometer The trip odometer can record the number of miles, used in the United States, or kilometers, used in Canada, traveled for up to two trips. Cycle between the odometer and trip odometers A and B by pressing the reset button located in the lower right area of the speedometer . Press the reset button to tell how many miles or kilometers have been recorded on either T rip A or Trip B since the trip odometer was last set ba[...]

Safety Belt Reminders Driver Safety Belt Reminder Light When the engine is started, a chime sounds for several seconds to remind a driver to fasten the safety belt, unless the driver safety belt is already buckled. The safety belt light comes on and stays on for several seconds, then flashes for several more. This chime and light are repeated if the driver remains unbuckled and the vehicle is in motion. If the driver safety belt is already buckled, neither the chime nor the light comes on. Passenger Safety Belt Reminder Light For vehicles equipped with the passenger safety belt reminder light, several seconds after the engine is started, a chime sounds for several seconds to remind the front[...]

Airbag Readiness Light There is an airbag readiness light on the instrument panel cluster , which shows the airbag symbol. The system checks the airbag's electrical system for malfunctions. The light tells if there is an electrical problem. The system check includes the airbag sensor , the airbag modules, the wiring and the crash sensing and diagnostic module. For more information on the airbag system, see Airbag System on page 2 ‑ 58 . This light comes on when the vehicle is started, and it will flash for a few seconds. When the light goes out this indicates the system is functioning properly . If the airbag readiness light stays on or comes on while driving, the airbag system may no[...]

Passenger Airbag Status Indicator The vehicle has the passenger sensing system. See Passenger Sensing System on page 2 ‑ 65 for important safety information. The vehicle has a passenger airbag status indicator near the clock, located in the center of the instrument panel. United States Canada When the vehicle is started, the passenger airbag status indicator will light P ASSENGER AIRBAG ON and P ASSENGER AIRBAG OFF or the symbol for on and off, for several seconds as a system check. Then, after several more seconds, the status indicator will light either P ASSENGER AIRBAG ON or P ASSENGER AIRBAG OFF , or either the on or of f symbol, to let you know the status of the right front passenger [...]

Charging System Light This light will come on briefly when the ignition is turned on, and the engine is not running, as a check to show it is working. It should go out when the engine is started. If it stays on, or comes on while driving, there may have a problem with the electrical charging system. Have it checked by your dealer/retailer . Driving while this light is on could drain the battery . If a short distance must be driven with the light on, turn off all accessories, such as the radio and air conditioner to help reduce the drain on the battery . Up-Shift Light The vehicle may have an up-shift light. When this light comes on, shift to the next higher gear if weather , road, and traffi[...]

Brake System W arning Light The vehicle's hydraulic brake system is divided into two parts. If one part is not working, the other part can still work and stop the vehicle. For good braking, both parts need to work. If the warning light comes on, there is a brake problem. Have the brake system inspected right away . United States Canada { W ARNING: The brake system might not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to a crash. If the light is still on after the vehicle has been pulled off the road and carefully stopped, have the vehicle towed for service. This light should come on briefly when the ignition is tur[...]

Antilock Brake System (ABS) W arning Light For vehicles with the Antilock Brake System (ABS), this light comes on briefly when the engine is started. If the light stays on, turn the ignition to LOCK/OFF or if the light comes on, stop as soon as possible and turn the ignition off. Then start the engine again to reset the system. If the light still stays on, or comes on again while driving, the vehicle needs service. See your dealer/retailer . If the regular brake system warning light is not on, the brakes will still work, but the antilock brakes will not work. If the regular brake system warning light is also on, the antilock brakes will not work and there is a problem with the regular brakes[...]

Engine Coolant T emperature Gauge United States Canada The vehicle has an engine coolant temperature gauge. With the ignition turned to ON/RUN, this gauge shows the engine coolant temperature. If the gauge pointer moves into the red area, the engine is too hot. It means that the engine coolant has overheated. If the vehicle has been operating under normal driving conditions, pull off the road, stop the vehicle and turn off the engine as soon as possible. See Engine Overheating on page 6 ‑ 30 . Tire Pressure Light For vehicles with the tire pressure monitoring system, this light comes on briefly when the engine is started. It provides information about tire pressures and the Tire Pressure M[...]

Malfunction Indicator Lamp Check Engine Light A computer system called OBD II (On-Board Diagnostics-Second Generation) monitors operation of the fuel, ignition, and emission control systems. It makes sure that emissions are at acceptable levels for the life of the vehicle, helping to produce a cleaner environment. This light comes on when the ignition is on, but the engine is not running, as a check to show it is working. If it does not, have the vehicle serviced by your dealer/retailer . If the check engine light comes on and stays on, while the engine is running, this indicates that there is an OBD II problem and service is required. Malfunctions often are indicated by the system before an[...]

The following can prevent more serious damage to the vehicle: . Reduce vehicle speed. . Avoid hard accelerations. . Avoid steep uphill grades. If the light continues to flash, when it is safe to do so, stop the vehicle. Find a safe place to park the vehicle. T urn the key off, wait at least 10 seconds, and restart the engine. If the light is still flashing, follow the previous steps and see your dealer/retailer for service as soon as possible. Light On Steady: An emission control system malfunction has been detected on the vehicle. Diagnosis and service might be required. An emission system malfunction might be corrected by doing the following: . Make sure the fuel cap is fully installed. Se[...]

Emissions Inspection and Maintenance Programs Some state/provincial and local governments have or might begin programs to inspect the emission control equipment on the vehicle. Failure to pass this inspection could prevent getting a vehicle registration. Here are some things to know to help the vehicle pass an inspection: . The vehicle will not pass this inspection if the check engine light is on with the engine running, or if the key is in the ON/RUN and the light is not on. . The vehicle will not pass this inspection if the OBD II (on-board diagnostic) system determines that critical emission control systems have not been completely diagnosed by the system. The vehicle would be considered [...]

The oil light could also come on in three other situations: . When the ignition is on but the engine is not running, the light will come on as a test to show it is working. The light will go out when the ignition is turned on. If it does not come on with the ignition on, there may be a problem with the fuse or bulb. Have it fixed right away . . If the vehicle comes to a hard stop, the light may come on for a moment. This is normal. { W ARNING: Do not keep driving if the oil pressure is low . The engine can become so hot that it catches fire. Someone could be burned. Check the oil as soon as possible and have the vehicle serviced. Notice: Lack of proper engine oil maintenance can damage the e[...]

Fog Lamp Light For vehicles with this feature, the fog lamps light will come on when the fog lamps are in use. The light will go out when the fog lamps are turned off. See Fog Lamps on page 4 ‑ 12 for more information. Cruise Control Light If the vehicle has cruise control, this light comes on whenever the cruise control is set The light will go out when the cruise control is turned off. See Cruise Control on page 4 ‑ 8 for more information. Highbeam On Light This light comes on when the high-beam headlamps are in use. See Headlamp High/Low-Beam Changer on page 4 ‑ 5 for more information. Daytime Running Lamps (DRL) Indicator Light This light turns on whenever the Daytime Running Lamps[...]

Door Ajar Light The door ajar light comes on and stays on until all doors, trunk and liftgate are closed and completely latched. If the key is in the ignition while the driver's door is open, a warning chime also sounds. Fuel Gauge United States Canada The fuel gauge indicates about how much fuel is left when the ignition is turned to ON/RUN. When the tank nears empty , the low fuel warning light will come on. There is still a little fuel left, but the vehicle's fuel tank should be filled soon. See Low Fuel Warning Light on page 4 ‑ 37 for more information. An arrow on the fuel gauge indicates the side of the vehicle the fuel door is located. 4-36[...]

Here are four things that some owners ask about. None of these show a problem with the fuel gauge: . At the service station, the gas pump shuts off before the gauge reads full. . It takes a little more or less fuel to fill up than the gauge indicated. For example, the gauge may have indicated the tank was half full, but it actually took a little more or less than half the tank's capacity to fill the tank. . The indicator moves a little when turning a corner or speeding up. . The gauge goes back to empty when the ignition is turned off. Low Fuel W arning Light This light comes on when the vehicle is low on fuel. The low fuel warning light comes on when there is approximately 1.7 gallons [...]

T rip Computer The vehicle may have trip computer , it provides the driver with driving information such as the driving distance for the remaining fuel, outside temperature, average fuel economy , and driving time. The trip computer button is located in the lower right area of the tachometer . Each time you press it, the display cycles through the available choices. Range for Remaining Fuel This display shows the approximate number of remaining miles the vehicle can be driven without refueling. The minimum display for the range is 45 miles (72 km). Once the minimum display range is under 45 miles (72 km), you will see dashes on the display . The fuel range estimate is based on an average of [...]

Driving Time This display can be used as a timer . The display will show the amount of time that has passed since the timer was last reset. The timer is only running while the vehicle is moving. T o reset the driving time press and hold the trip computer button. Audio System(s) Determine which radio the vehicle has and read the following pages to become familiar with its features. { W ARNING: T aking your eyes off the road for extended periods could cause a crash resulting in injury or death to you or others. Do not give extended attention to entertainment tasks while driving. This system provides access to many audio and non audio listings. T o minimize taking your eyes off the road while d[...]

AM-FM Radio Playing the Radio O (Power/V olume) : Press and release to turn the system on. Press and hold this knob for more than two seconds to turn the system off. T urn to increase or decrease the volume. When the system is on, press and release O to mute the system. Press and release O again to turn the sound back on. Finding a Station BAND: Press to choose FM, AM, or XM ™ (if equipped). The display will show the selection. u SEEK: Press to seek the next radio station with a strong signal in the selected band. t SEEK: Press to seek the previous radio station with a strong signal in the selected band. [ TUNE: Press to go to the next station manually . r TUNE: Press to go to the previous[...]

T o use Automatic Store: 1. Press and hold AST to use Auto Store mode. 2. Press the pushbutton below the ON tab on the radio display . 3. Automatic Store searches for radio stations with a strong signal and automatically set presets A1 and A2 with new stations. 4. After all stations are set, press the pushbutton below the arrow tab on the radio display to return to the main radio screen T o reset the automatically stored radio stations, press and hold AST . Then press the pushbutton below the RESE tab on the radio display . If no stations are stored on preset pages A1 and A2, the RESE option does not appear in the radio display . When the Automatic Store function is used, any stations that w[...]

T o setup the number of favorites pages: 1. Press and hold F A V until the radio setup menu displays. 2. Select the desired number of favorites pages by pressing the pushbutton located below the displayed page numbers. 3. Press F A V to return to the original main radio screen showing the radio station frequency tabs and to begin the process of programming favorites for the chosen amount of numbered pages. Setting the T one (Bass/Mid/T reble) SOUND (Bass/Mid/T reble): Press to adjust the bass, midrange, or treble. Adjusting the Bass T o adjust the bass: 1. Press SOUND. 2. Press the pushbutton below the Bass tab on the display . 3. T urn O to adjust the setting. 4. The settings are saved afte[...]

Adjusting the Speakers (Balance/Fade) SOUND (Balance/Fade): Press to adjust the balance or fade. Adjusting the Balance T o adjust the balance: 1. Press SOUND. 2. Press the pushbutton below the Bal tab on the display . 3. T urn O to adjust the setting. 4. The settings are saved after five seconds. Adjusting the Fade T o adjust the fade: 1. Press SOUND. 2. Press the pushbutton below the Fad tab on the display . 3. T urn O to adjust the setting. 4. The settings are saved after five seconds. Setting the EQ SOUND (Equalization): Press to select an equalization setting. Setting the EQ T o set the EQ: 1. Press SOUND. 2. Press the pushbutton below the P .EQ tab on the display . The Pop, Rock, Ctry ,[...]

XM Satellite Radio Service XM is a satellite radio service that is based in the 48 contiguous United States and 10 Canadian provinces. XM Satellite Radio has a wide variety of programming and commercial-free music, coast-to-coast, and in digital-quality sound. A service fee is required to receive the XM service. For more information, contact XM at www .xmradio.com or call 1-800-929-2100 in the U.S. and www .xmradio.ca or call 1-877-438-9677 in Canada. Radio Messages for XM Only See XM Radio Messages on page 4 ‑ 63 later in this section for further detail. Using the Auxiliary Input Jack The radio system has a 3.5 mm (1/8 in) auxiliary input jack located on the lower right side of the facepl[...]

Radio with CD Playing the Radio O (Power/V olume): Press and release to turn the system on. Press and hold this knob for more than two seconds to turn the system off. T urn to increase or decrease the volume. When the system is on, press and release O to mute the system. Press and release O again to turn the sound back on. Finding a Station BAND: Press to choose FM, AM, or XM ™ (if equipped). The display will show the selection. u SEEK: Press to seek the next radio station with a strong signal in the selected band. t SEEK: Press to seek the previous radio station with a strong signal in the selected band. [ TUNE: Press to go to the next station manually . r TUNE: Press to go to the previou[...]

AST (Automatic Store): T welve preset stations with the strongest reception in the area can be automatically stored. The radio will only scan stations with a strong signal that are in the selected AM or FM band. If the Automatic Store function is started in the FM band, only FM stations are stored in preset pages A1 and A2. If the Automatic Store function is started in the AM band, only AM stations are stored in A1 and A2. A combination of AM, FM and XM (if equipped) stations can be stored manually into the other four favorite pages. T o use Automatic Store: 1. Press and hold SCAN/AST to use Auto Store mode. 2. Press the pushbutton below the ON tab on the radio display . 3. Automatic Store s[...]

T o setup the number of favorites pages: 1. Press and hold F A V until the radio setup menu displays. 2. Select the desired number of favorites pages by pressing the pushbutton located below the displayed page numbers. 3. Press F A V to return to the original main radio screen showing the radio station frequency tabs and to begin the process of programming favorites for the chosen amount of numbered pages. Setting the T one (Bass/Mid/T reble) SOUND (Bass/Mid/T reble): Press to adjust the bass, midrange, or treble. Adjusting the Bass T o adjust the bass: 1. Press SOUND. 2. Press the pushbutton below the Bass tab on the display . 3. T urn O to adjust the setting. 4. The settings are saved afte[...]

Adjusting the Speakers (Balance/Fade) SOUND (Balance/Fade): Press to adjust the balance or fade. Adjusting the Balance T o adjust the balance: 1. Press SOUND. 2. Press the pushbutton below the Bal tab on the display . 3. T urn O to adjust the setting. 4. The settings are saved after five seconds. Adjusting the Fade T o adjust the fade: 1. Press SOUND. 2. Press the pushbutton below the Fad tab on the display . 3. T urn O to adjust the setting. 4. The settings are saved after five seconds. Setting the EQ SOUND (Equalization): Press to select an equalization setting. Setting the EQ T o set the EQ: 1. Press SOUND. 2. Press the pushbutton below the P .EQ tab on the display . The Pop, Rock, Ctry ,[...]

XM Satellite Radio Service XM is a satellite radio service that is based in the 48 contiguous United States and 10 Canadian provinces. XM Satellite Radio has a wide variety of programming and commercial-free music, coast-to-coast, and in digital-quality sound. A service fee is required to receive the XM service. For more information, contact XM at www .xmradio.com or call 1-800-929-2100 in the U.S. and www .xmradio.ca or call 1-877-438-9677 in Canada. Radio Messages for XM Only See XM Radio Messages on page 4 ‑ 63 later in this section for further detail. Playing a CD Insert a CD partway into the slot, label side up. The player pulls it in and the CD begins playing. A CD can be loaded whil[...]

BAND: Press to listen to the radio while a CD is playing. The CD remains inside the radio for future listening. CD/AUX: Press to play a CD when listening to the radio. CDP appears on the display when the CD player has been selected. The CD symbol will appear on the display when a CD is loaded. Press CD/AUX while a CD is playing to pause the CD. P AUSE flashes on the display . Press CD/AUX again to start playing the CD. Press CD/AUX to play a CD when listening to the audio contents from other device (AUX mode). CDP appears on the display when the CD player has been selected. The CD symbol will appear on the display when a CD is loaded. EJECT : Press to eject a CD. The CD can be ejected when t[...]

CD Messages CHECK CD: If this message displays and/or the CD comes out, it could be for one of the following reasons: . It is very hot. When the temperature returns to normal, the CD should play . . The road is very rough. When the road becomes smoother , the CD should play . . The CD is dirty , scratched, wet, or upside down. . The air is very humid. If so, wait about an hour and try again. . The format of the CD might not be compatible. See Using an MP3 on page 4 ‑ 61 later in this section. . There could have been a problem while burning the CD. . The label could be caught in the CD player . If the CD is not playing correctly , for any other reason, try a known good CD. If any error occu[...]

Care of the CD Player Do not add labels to a CD, it could get caught in the CD player . Use a marking pen to write on the top of the CD if a description is needed. Do not use CD lens cleaners, they could damage the CD player . Notice: If a label is added to a CD, or more than one CD is inserted into the slot at a time, or an attempt is made to play scratched or damaged CDs, the CD player could be damaged. While using the CD player , use only CDs in good condition without any label, load one CD at a time, and keep the CD player and the loading slot free of foreign materials, liquids, and debris. If an error displays, see “ CD Messages ” earlier in this section. Using the Auxiliary Input J[...]

Radio with Six-Disc CD Playing the Radio O (Power/V olume): Press and release to turn the system on. Press and hold this knob for more than two seconds to turn the system off. T urn to increase or decrease the volume. When the system is on, press and release O to mute the system. Press and release O again to turn the sound back on. Finding a Station BAND: Press to choose FM, AM, or XM ™ (if equipped). The display will show the selection. u SEEK: Press to seek the next radio station with a strong signal in the selected band. t SEEK: Press to seek the previous radio station with a strong signal in the selected band. [ TUNE: Press to go to the next station manually . r TUNE: Press to go to th[...]

AST (Automatic Store): T welve preset stations with the strongest reception in the area can be automatically stored. The radio will only scan stations with a strong signal that are in the selected AM or FM band. If the Automatic Store function is started in the FM band, only FM stations are stored in preset pages A1 and A2. If the Automatic Store function is started in the AM band, only AM stations are stored in A1 and A2. A combination of AM, FM and XM (if equipped) stations can be stored manually into the other four favorite pages. T o use Automatic Store: 1. Press and hold SCAN/AST to use Auto Store mode. 2. Press the pushbutton below the ON tab on the radio display . 3. Automatic Store s[...]

T o setup the number of favorites pages: 1. Press and hold F A V until the radio setup menu displays. 2. Select the desired number of favorites pages by pressing the pushbutton located below the displayed page numbers. 3. Press F A V to return to the original main radio screen showing the radio station frequency tabs and to begin the process of programming favorites for the chosen amount of numbered pages. Setting the T one (Bass/Mid/T reble) SOUND (Bass/Mid/T reble): Press to adjust the bass, midrange, or treble. Adjusting the Bass T o adjust the bass: 1. Press SOUND. 2. Press the pushbutton below the Bass tab on the display . 3. T urn O to adjust the setting. 4. The settings are saved afte[...]

Adjusting the Speakers (Balance/Fade) SOUND (Balance/Fade): Press to adjust the balance or fade. Adjusting the Balance T o adjust the balance: 1. Press SOUND. 2. Press the pushbutton below the Bal tab on the display . 3. T urn O to adjust the setting. 4. The settings are saved after five seconds. Adjusting the Fade T o adjust the fade: 1. Press SOUND. 2. Press the pushbutton below the Fad tab on the display . 3. T urn O to adjust the setting. 4. The settings are saved after five seconds. Setting the EQ SOUND (Equalization): Press to select an equalization setting. Setting the EQ T o set the EQ: 1. Press SOUND. 2. Press the pushbutton below the P .EQ tab on the display . The Pop, Rock, Ctry ,[...]

Radio Messages for XM Only See XM Radio Messages on page 4 ‑ 63 later in this section for further detail. Playing a CD(s) Loading a CD(s) The CD player can hold up to six CDs. As each CD is inserted, CDP will appear on the display and as each CD is loading. File check will appear on the display . Once playback begins, the track and track number will appear on the display . If the ignition or radio is turned off with a CD in the player , it will stay in the player . When a CD is in the player and the ignition is in the ON/RUN position, the radio must be turned on before the CD will start playing. When the ignition and radio are turned on, the CD will start playing where it stopped, if it wa[...]

LOAD: Press to load CDs into the CD player . [ TUNE (Next T rack): Press [ TUNE to go to the next track. The track number will appear on the display . The player will continue moving forward through the CD with each press of [ TUNE. r TUNE (Previous T rack): Press to go to the start of the current track. The track number will appear on the display . The player will continue moving backward through the CD with each press of r TUNE. DSC − (Previous CDC): Press to go back to the start of the previous CDC. DSC + (Next CDC): Press to go forward to the start of the next CDC. BAND: Press to listen to the radio while a CD is playing. The CD remains inside the radio for future listening. CD/AUX: Pr[...]

INT (Scan): Press the pushbutton below the INT tab on the display to listen to the first few seconds of each track on each CD loaded, INTRO appears on the display . Press the pushbutton again to stop scanning and the current track begins to play . Playing an MP3/WMA CD-R Disc The radio has the MP3/WMA CD-R disc capability . For more information, see Using an MP3 on page 4 ‑ 61 later in this section. CD Messages CHECK CD: If this message displays and/or the CD comes out, it could be for one of the following reasons: . It is very hot. When the temperature returns to normal, the CD should play . . The road is very rough. When the road becomes smoother , the CD should play . . The CD is dirty [...]

Care of the CD Player Do not add labels to a CD, it could get caught in the CD player . Use a marking pen to write on the top of the CD if a description is needed. Do not use CD lens cleaners, they could damage the CD player . Notice: If a label is added to a CD, or more than one CD is inserted into the slot at a time, or an attempt is made to play scratched or damaged CDs, the CD player could be damaged. While using the CD player , use only CDs in good condition without any label, load one CD at a time, and keep the CD player and the loading slot free of foreign materials, liquids, and debris. If an error displays, see “ CD Messages ” earlier in this section. Using the Auxiliary Input J[...]

Using an MP3 MP3/WMA CD-R Disc MP3 Format If you burn your own MP3/WMA disc on a personal computer: . Make sure the MP3/WMA files are recorded on a CD-R disc. . Do not mix standard audio and MP3/WMA files on one disc. . Make sure each MP3/WMA file has a .m3u or .wma extension, other file extensions might not work. . Files can be recorded with a variety of fixed or variable bit rates. Song title, artist name, and album are available for display by the radio when recorded using ID3 tags version 1 and 2. . Make sure to finalize the disc when burning an MP3/WMA disc, using multiple sessions. It is usually better to burn the disc all at once. The player is able to read and play a maximum of 50 fo[...]

No Folder When a CD contains only compressed files, the files are located under the root folder . The next and previous folder function does not function on a CD that was recorded without folders or playlists. When displaying the name of the folder the radio displays ROOT . When a CD contains only compressed audio files, but no folders, all files are located under the root folder . When the radio displays the name of the folder , the radio displays ROOT . Order of Play The player play will begin from the first track under the root directory . When all tracks from the root directory have been played, play will continue from files according to their numerical listing. After playing the last tr[...]

u SEEK t (Next/Previous Folder) (in MP3/WMA Mode): Press to change the folder . If CD-R does not have any folders, “ ROOT ” flashes on the display for a short time. [ TUNE (Next T rack): Press the up TUNE arrow to go to the next track. The track number displays. The player continues moving forward through the CD each time TUNE is pressed. r TUNE (Previous T rack): Press the down TUNE arrow to go to the start of the current track. The track number displays. The player continues moving backward through the CD each time TUNE is pressed. INFO/DISP (Information/Display): Press to display additional text information related to the current MP3/ WMA song. A choice of additional information such [...]

Audio Steering Wheel Controls Front View of the Steering Wheel Controls Side View of the V olume Control If the vehicle has this feature, some audio controls can be adjusted at the steering wheel. PWR (Power): Press and release to turn the system on and off. When the system is on, press and release for a short time to mute the system. Press and release again to turn the sound back on. + VOLUME − : Press the toggle bar located below the + VOLUME − to adjust the volume. Press the left side of the toggle bar , below the + (plus) sign to increase the volume. Press the right side of the toggle bar , below the − (minus) sign to decrease the volume. MODE: Press and release this button multipl[...]

Radio Reception Frequency interference and static can occur during normal radio reception if items such as cell phone chargers, vehicle convenience accessories, and external electronic devices are plugged into the accessory power outlet. If there is interference or static, unplug the item from the accessory power outlet. AM The range for most AM stations is greater than for FM, especially at night. The longer range can cause station frequencies to interfere with each other . For better radio reception, most AM radio stations boost the power levels during the day , and then reduce these levels during the night. Static can also occur when things like storms and power lines interfere with radio[...]

Backglass Antenna (Sedan) V ehicles without OnStar ® have the AM-FM antenna integrated with the rear window defogger , located in the rear window . Make sure that the inside surface of the rear window is not scratched and that the lines on the glass are not damaged. If the inside surface is damaged, it could interfere with radio reception. Also, for proper radio reception, the antenna connector at the top-center of the rear window needs to be properly attached to the post on the glass. Notice: Using a razor blade or sharp object to clear the inside rear window can damage the rear window antenna and/or the rear window defogger . Repairs would not be covered by the vehicle warranty . Do not c[...]

Section 5 Driving Y our V ehicle Y our Driving, the Road, and the Vehicle . . . . . . . . . . 5-2 Defensive Driving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 D r u n k D r i v i n g ... ................................ 5 - 2 Control of a V ehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3 B r a k i n g ... ...................................... 5 - 3 Antilock Brake System (ABS) . . . . . . . . . . . . . . . . . . . 5-4 Braking in Emergencies . . . . . . . . . . . . . . . . . . . . . . . . . 5-5 Steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5 Off-Road Recovery . . . . . . . . . . . . . . . . . . . . . . [...]

Y our Driving, the Road, and the V ehicle Defensive Driving Defensive driving means “ always expect the unexpected. ” The first step in driving defensively is to wear your safety belt — See Safety Belts: They Are for Everyone on page 2 ‑ 14 . { W ARNING: Assume that other road users (pedestrians, bicyclists, and other drivers) are going to be careless and make mistakes. Anticipate what they might do and be ready . In addition: . Allow enough following distance between you and the driver in front of you. . Focus on the task of driving. Driver distraction can cause collisions resulting in injury or possible death. These simple defensive driving techniques could save your life. Drunk Dr[...]

For persons under 21, it is against the law in every U.S. state to drink alcohol. There are good medical, psychological, and developmental reasons for these laws. The obvious way to eliminate the leading highway safety problem is for people never to drink alcohol and then drive. Medical research shows that alcohol in a person's system can make crash injuries worse, especially injuries to the brain, spinal cord, or heart. This means that when anyone who has been drinking — driver or passenger — is in a crash, that person's chance of being killed or permanently disabled is higher than if the person had not been drinking. Control of a V ehicle The following three systems help to c[...]

Avoid needless heavy braking. Some people drive in spurts, heavy acceleration followed by heavy braking, rather than keeping pace with traffic. This is a mistake. The brakes might not have time to cool between hard stops. The brakes will wear out much faster with a lot of heavy braking. Keeping pace with the traffic and allowing realistic following distances eliminates a lot of unnecessary braking. That means better braking and longer brake life. If the engine ever stops while the vehicle is being driven, brake normally but do not pump the brakes. If the brakes are pumped, the pedal could get harder to push down. If the engine stops, there will still be some power brake assist but it will be[...]

Remember: ABS does not change the time needed to get a foot up to the brake pedal or always decrease stopping distance. If you get too close to the vehicle in front of you, there will not be enough time to apply the brakes if that vehicle suddenly slows or stops. Always leave enough room up ahead to stop, even with ABS. Using ABS Do not pump the brakes. Just hold the brake pedal down firmly and let antilock work. A slight brake pedal pulsation might be felt or some noise might be heard, but this is normal. Braking in Emergencies At some time, nearly every driver gets into a situation that requires hard braking. If the vehicle has ABS, it allows the driver to steer and brake at the same time.[...]

If there is a need to reduce speed, do it before entering the curve, while the front wheels are straight. T ry to adjust the speed so you can drive through the curve. Maintain a reasonable, steady speed. W ait to accelerate until out of the curve, and then accelerate gently into the straightaway . Steering in Emergencies There are times when steering can be more effective than braking. For example, you come over a hill and find a truck stopped in your lane, or a car suddenly pulls out from nowhere, or a child darts out from between parked cars and stops right in front of you. These problems can be avoided by braking — if you can stop in time. But sometimes you cannot stop in time because t[...]

Off-Road Recovery The vehicle's right wheels can drop off the edge of a road onto the shoulder while driving. If the level of the shoulder is only slightly below the pavement, recovery should be fairly easy . Ease off the accelerator and then, if there is nothing in the way , steer so that the vehicle straddles the edge of the pavement. T urn the steering wheel 8 to 13 cm (3 to 5 inches), about one-eighth turn, until the right front tire contacts the pavement edge. Then turn the steering wheel to go straight down the roadway . Passing Passing another vehicle on a two-lane road can be dangerous. T o reduce the risk of danger while passing: . Look down the road, to the sides, and to cross[...]

Loss of Control Let us review what driving experts say about what happens when the three control systems — brakes, steering, and acceleration — do not have enough friction where the tires meet the road to do what the driver has asked. In any emergency , do not give up. Keep trying to steer and constantly seek an escape route or area of less danger . Skidding In a skid, a driver can lose control of the vehicle. Defensive drivers avoid most skids by taking reasonable care suited to existing conditions, and by not overdriving those conditions. But skids are always possible. The three types of skids correspond to the vehicle's three control systems. In the braking skid, the wheels are n[...]

Driving at Night Night driving is more dangerous than day driving because some drivers are likely to be impaired — by alcohol or drugs, with night vision problems, or by fatigue. Night driving tips include: . Drive defensively . . Do not drink and drive. . Reduce headlamp glare by adjusting the inside rearview mirror . . Slow down and keep more space between you and other vehicles because headlamps can only light up so much road ahead. . W atch for animals. . When tired, pull off the road. . Do not wear sunglasses. . Avoid staring directly into approaching headlamps. . Keep the windshield and all glass on your vehicle clean — inside and out. . Keep your eyes moving, especially during tur[...]

Hydroplaning Hydroplaning is dangerous. Water can build up under your vehicle's tires so they actually ride on the water . This can happen if the road is wet enough and you are going fast enough. When your vehicle is hydroplaning, it has little or no contact with the road. There is no hard and fast rule about hydroplaning. The best advice is to slow down when the road is wet. Other Rainy Weather T ips Besides slowing down, other wet weather driving tips include: . Allow extra following distance. . Pass with caution. . Keep windshield wiping equipment in good shape. . Keep the windshield washer fluid reservoir filled. . Have good tires with proper tread depth. See Tires on page 6 ‑ 51 [...]

Hill and Mountain Roads Driving on steep hills or through mountains is different than driving on flat or rolling terrain. Tips for driving in these conditions include: . Keep the vehicle serviced and in good shape. . Check all fluid levels and brakes, tires, cooling system, and transmission. . Going down steep or long hills, shift to a lower gear . { W ARNING: If you do not shift down, the brakes could get so hot that they would not work well. Y ou would then have poor braking or even none going down a hill. Y ou could crash. Shift down to let the engine assist the brakes on a steep downhill slope. { W ARNING: Coasting downhill in N (Neutral) or with the ignition off is dangerous. The brakes[...]

Winter Driving Driving on Snow or Ice Drive carefully when there is snow or ice between the tires and the road, creating less traction or grip. Wet ice can occur at about 0°C (32°F) when freezing rain begins to fall, resulting in even less traction. Avoid driving on wet ice or in freezing rain until roads can be treated with salt or sand. Drive with caution, whatever the condition. Accelerate gently so traction is not lost. Accelerating too quickly causes the wheels to spin and makes the surface under the tires slick, so there is even less traction. T ry not to break the fragile traction. If you accelerate too fast, the drive wheels will spin and polish the surface under the tires even mor[...]

{ W ARNING: Snow can trap engine exhaust under the vehicle. This may cause exhaust gases to get inside. Engine exhaust contains carbon monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death. If the vehicle is stuck in the snow: . Clear away snow from around the base of your vehicle, especially any that is blocking the exhaust pipe. . Check again from time to time to be sure snow does not collect there. . Open a window about 5 cm (two inches) on the side of the vehicle that is away from the wind to bring in fresh air . . Fully open the air outlets on or under the instrument panel. . Adjust the Climate Control system to a setting that circulates the air insi[...]

If Y our V ehicle is Stuck in Sand, Mud, Ice, or Snow Slowly and cautiously spin the wheels to free the vehicle when stuck in sand, mud, ice, or snow. See Rocking Y our V ehicle to Get It Out on page 5 ‑ 14 . { W ARNING: If you let your vehicle's tires spin at high speed, they can explode, and you or others could be injured. The vehicle can overheat, causing an engine compartment fire or other damage. Spin the wheels as little as possible and avoid going above 55 km/h (35 mph) as shown on the speedometer . For information about using tire chains on the vehicle, see Tire Chains on page 6 ‑ 69 . Rocking Y our V ehicle to Get It Out T urn the steering wheel left and right to clear the [...]

Loading the V ehicle It is very important to know how much weight your vehicle can carry . This weight is called the vehicle capacity weight or maximum load amount and includes the weight of all occupants, cargo, and all nonfactory ‐ installed options. T wo labels on your vehicle show how much weight it may properly carry , the Tire and Loading Information label and the Certification label. { W ARNING: Do not load the vehicle any heavier than the Gross V ehicle Weight Rating (GVWR), or either the maximum front or rear Gross Axle Weight Rating (GA WR). If you do, parts on the vehicle can break, and it can change the way the vehicle handles. These could cause you to lose control and crash. A[...]

The T ire and Loading Information label also shows the tire size of the original equipment tires (C) and the recommended cold tire inflation pressures (D). For more information on tires and inflation see Tires on page 6 ‑ 51 and Inflation - Tire Pressure on page 6 ‑ 58 . There is also important loading information on the Certification label. See “ Certification Label ” later in this section. Steps for Determining Correct Load Limit 1. Locate the statement “ The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs ” on your vehicle's placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3. Subtract [...]

Example 1 Item Description T otal A V ehicle Capacity Weight for Example 1 = 1,000 lbs (453 kg) B Subtract Occupant Weight @ 150 lbs (68 kg) × 2 = 300 lbs (136 kg) C Available Occupant and Cargo Weight = 700 lbs (317 kg) Example 2 Item Description T otal A V ehicle Capacity Weight for Example 2 = 1,000 lbs (453 kg) B Subtract Occupant Weight @ 150 lbs (68 kg) × 5 = 750 lbs (340 kg) C Available Cargo Weight = 250 lbs (1 13 kg) 5-17[...]

Example 3 Item Description T otal A V ehicle Capacity Weight for Example 3 = 1,000 lbs (453 kg) B Subtract Occupant Weight @ 200 lbs (91 kg) × 5 = 1,000 lbs (453 kg) C Available Cargo Weight = 0 lbs (0 kg) Refer to your vehicle's tire and loading information label for specific information about your vehicle's capacity weight and seating positions. The combined weight of the driver , passenge r , and cargo should never exceed your vehicle's capacity weight. 5-18[...]

Certification Label Label Example ‐ United States Label Example ‐ Canada A vehicle specific Certification label is attached to the center pillar (B ‐ pillar), below the driver's door latch. This label tells you the gross weight capacity of your vehicle, called the Gross V ehicle Weight Rating (GVWR). The GVWR includes the weight of the vehicle, all occupants, fuel and cargo. Never exceed the GVWR for your vehicle, or the Gross Axle Weight Rating (GA WR) for either the front or rear axle. 5-19[...]

If there is a heavy load, it should be spread out. See “ Steps for Determining Correct Load Limit ” earlier in this section. { W ARNING: Do not load the vehicle any heavier than the Gross V ehicle Weight Rating (GVWR), or either the maximum front or rear Gross Axle Weight Rating (GA WR). If you do, parts on the vehicle can break, and it can change the way the vehicle handles. These could cause you to lose control and crash. Also, overloading can shorten the life of the vehicle. Notice : Overloadin g the vehicle may cause damage. Repairs would not be covered by the vehicle warranty . Do not overload the vehicle. If you put things inside your vehicle — like suitcases, tools, packages, or[...]

T owing T owing Y our V ehicle T o avoid damage, the disabled vehicle should be towed with all four wheels off the ground. Consult your dealer/ retailer or a professional towing service if the disabled vehicle must be towed. See Roadside Assistance Program on page 8 ‑ 7 . T o tow the vehicle behind another vehicle for recreational purposes, such as behind a motorhome, see “ Recreational V ehicle T owing ” following. Recreational V ehicle T owing Recreational vehicle towing means towing the vehicle behind another vehicle – such as behind a motorhome. The two most common types of recreational vehicle towing are known as dinghy towing and dolly towing. Dinghy towing is towing the vehicl[...]

Dinghy T owing Notice: If the vehicle is towed with all four wheels on the ground, the drivetrain components could be damaged. The repairs would not be covered by the vehicle warranty . Do not tow the vehicle with all four wheels on the ground. The vehicle was not designed to be towed with all four wheels on the ground. If the vehicle must be towed, a dolly should be used. See “ Dolly T owing ” that follows for more information. Dolly T owing From the Front The vehicle can be towed from the front using a dolly . T o tow the vehicle using a dolly , follow these steps: 1. Attach the dolly to the tow vehicle following the dolly manufacturer's instructions. 2. Drive the front wheels ont[...]

4. Set the parking brake and remove the key . 5. For an automatic transmission, insert the key into the shift ‐ lock release slot and shift to N (Neutral). See Shifting Out of Park on page 3 ‑ 30 . 6. Clamp the steering wheel in a straight-ahead position with a clamping device designed for towing. 7. Release the parking brake. Dolly T owing From the Rear Notice: T owing the vehicle from the rear with the front wheels on the ground could cause transmission damage. Do not tow the vehicle from the rear with the front wheels on the ground. T owing a T railer The vehicle is neither designed nor intended to tow a trailer . 5-23[...]

2 NOTES 5-24[...]

Section 6 Service and Appearance Care Service ......... .................................... 6-4 Accessories and Modifications . . . . . . . . . . . . . . . . . . 6-4 California Proposition 65 W arning . . . . . . . . . . . . . . . 6-5 California Perchlorate Materials R e q u i r e m e n t s ................................. 6 - 5 Doing Y our Own Service Work . . . . . . . . . . . . . . . . . . 6-5 Adding Equipment to the Outside of the V ehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6 Fuel .............................................. ... 6-6 Gasoline Octane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6 Gasoline Specification[...]

Section 6 Service and Appearance Care Center High-Mounted Stoplamp (CHMSL) (Sedan) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-47 T aillamps, T urn Signal, Sidemarker , Stoplamps and Back-up Lamps . . . . . . . . . . . . . . . . . . . . . . . . . 6-48 License Plate Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-49 Replacement Bulbs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-49 Windshield Wiper Blade Replacement ........... 6-50 Tires ............................ ................... 6-51 T ire Sidewall Labeling . . . . . . . . . . . . . . . . . . . . . . . . . 6-52 T ire T erminology and Definitions . . . . . . . . . . . . . . .[...]

Section 6 Service and Appearance Care Aluminum Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-84 T i r e s ........................................... 6 - 8 4 Sheet Metal Damage . . . . . . . . . . . . . . . . . . . . . . . . . . 6-84 Finish Damage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-85 Underbody Maintenance . . . . . . . . . . . . . . . . . . . . . . . 6-85 Chemical Paint Spotting . . . . . . . . . . . . . . . . . . . . . . . 6-85 V ehicle Identification ........................ ..... 6-86 V ehicle Identification Number (VIN) . . . . . . . . . . . . 6-86 Service Parts Identification Label . . . . . . . . . . . . . . 6-86 Electrical System ..[...]

Service For service and parts needs, visit your dealer/retailer . Y ou will receive genuine GM parts and GM-trained and supported service people. Genuine GM parts have one of these marks: Accessories and Modifications When non ‐ dealer/non ‐ retailer accessories are added to the vehicle, they can affect vehicle performance and safety , including such things as airbags, braking, stability , ride and handling, emissions systems, aerodynamics, durability , and electronic systems like antilock brakes, traction control, and stability control. Some of these accessories could even cause malfunction or damage not covered by the vehicle warranty . Damage to vehicle components resulting from the i[...]

California Proposition 65 W arning Most motor vehicles, including this one, contain and/or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Engine exhaust, many parts and systems, many fluids, and some component wear by-products contain and/or emit these chemicals. California Perchlorate Materials Requirements Certain types of automotive applications, such as airbag initiators, seat belt pretensioners, and lithium batteries contained in remote keyless transmitters, may contain perchlorate materials. Special handling may be necessary . For additional information, see www .dtsc.ca.gov/hazardouswaste/perchlorate. Doing Y our Own Servi[...]

Keep a record with all parts receipts and list the mileage and the date of any service work performed. See Maintenance Record on page 7 ‑ 15 . Adding Equipment to the Outside of the V ehicle Things added to the outside of the vehicle can affect the airflow around it. This can cause wind noise and can affect fuel economy and windshield washer performance. Check with your dealer/retailer before adding equipment to the outside of the vehicle. Fuel Use of the recommended fuel is an important part of the proper maintenance of this vehicle. T o help keep the engine clean and maintain optimum vehicle performance, we recommend the use of gasoline advertised as TOP TIER Detergent Gasoline. Look for[...]

Gasoline Specifications At a minimum, gasoline should meet ASTM specification D 4814 in the United States or CAN/CGSB ‐ 3.5 or 3.51 1 in Canada. Some gasolines contain an octane-enhancing additive called methylcyclopentadienyl manganese tricarbonyl (MMT). We recommend against the use of gasolines containing MMT . See Additives on page 6 ‑ 7 for additional information. California Fuel If the vehicle is certified to meet California Emissions Standards, it is designed to operate on fuels that meet California specifications. See the underhood emission control label. If this fuel is not available in states adopting California emissions standards, the vehicle will operate satisfactorily on fue[...]

Gasolines containing oxygenates, such as ethers and ethanol, and reformulated gasolines might be available in your area. We recommend that you use these gasolines, if they comply with the specifications described earlier . However , E85 (85% ethanol) and other fuels containing more than 10% ethanol must not be used in vehicles that were not designed for those fuels. Notice: This vehicle was not designed for fuel that contains methanol. Do not use fuel containing methanol. It can corrode metal parts in the fuel system and also damage plastic and rubber parts. That damage would not be covered under the vehicle warranty . Some gasolines that are not reformulated for low emissions can contain an[...]

W ARNING: (Continued) Keep sparks, flames, and smoking materials away from fuel. Do not leave the fuel pump unattended when refueling the vehicle. This is against the law in some places. Do not re-enter the vehicle while pumping fuel. Keep children away from the fuel pump; never let children pump fuel. T o open the fuel filler door , pull up on the release lever with this symbol on it. It is located on the floor on the outboard side of the driver seat. Hatchback shown. Sedan similar The tethered fuel cap is located behind a hinged fuel door on the passenger side of the vehicle. 6-9[...]

T o remove the fuel cap, turn it slowly counterclockwise. The fuel cap has a spring in it; if the cap is released too soon, it will spring back to the right. { W ARNING: Fuel can spray out on you if you open the fuel cap too quickly . If you spill fuel and then something ignites it, you could be badly burned. This spray can happen if the tank is nearly full, and is more likely in hot weather . Open the fuel cap slowly and wait for any hiss noise to stop. Then unscrew the cap all the way . Be careful not to spill fuel. Do not top off or overfill the tank and wait a few seconds after you have finished pumping before removing the nozzle. Clean fuel from painted surfaces as soon as possible. See[...]

Filling a Portable Fuel Container { W ARNING: Never fill a portable fuel container while it is in the vehicle. Static electricity discharge from the container can ignite the fuel vapor . Y ou can be badly burned and the vehicle damaged if this occurs. T o help avoid injury to you and others: . Dispense fuel only into approved containers. . Do not fill a container while it is inside a vehicle, in a vehicle's trunk, pickup bed, or on any surface other than the ground. . Bring the fill nozzle in contact with the inside of the fill opening before operating the nozzle. Contact should be maintained until the filling is complete. . Do not smoke while pumping fuel. . Do not use a cellular phone[...]

Hood Release T o open the hood: 1. Pull the hood release handle inside the vehicle. It is located on the lower left side of the instrument panel. 2. At the front of the vehicle, lift up on the secondary hood release lever , located under the front center of the hood. 6-12[...]

3. Lift the hood and release the hood prop from its retainer , located on the underside of the hood. Securely place the hood prop into the slot on the inner fender . T o close the hood: 1. Before closing the hood, be sure all the filler caps are on properly . Then, lift the hood to relieve pressure on the hood prop. Remove the hood prop from the slot in the inner fender and return the prop to its retainer . The prop rod must click into place when returning it to the retainer to prevent hood damage. 2. Lower the hood 30 cm (12 inches) above the vehicle and release it so it fully latches. Check to make sure the hood is closed and repeat the process if necessary . 6-13[...]

Engine Compartment Overview Automatic T ransmission shown, Manual T ransmission similar 6-14[...]

A. Engine Air Cleaner/Filter on page 6 ‑ 19 . B. Engine Oil Fill Cap. See “ When to Add Engine Oil ” under Engine Oil on page 6 ‑ 15 . C. Brake/Clutch Fluid Reservoir . See “ Brake Fluid ” under Brakes on page 6 ‑ 34 and Hydraulic Clutch on page 6 ‑ 23 . D. Engine Coolant Surge T ank. See Cooling System on page 6 ‑ 24 . E. Engine Compartment Fuse Block on page 6 ‑ 89 . F . Battery on page 6 ‑ 37 . G. Windshield W asher Fluid Reservoir . See “ Adding W asher Fluid ” under Windshield Washer Fluid on page 6 ‑ 33 . H. Engine Oil Dipstick. See “ Checking Engine Oil ” under Engine Oil on page 6 ‑ 15 . I. Automatic T ransmission Dipstick. See Automatic T ransmissio[...]

Checking Engine Oil It is a good idea to check the engine oil level at each fuel fill. In order to get an accurate reading, the oil must be warm and the vehicle must be on level ground. The engine oil dipstick handle is a yellow loop. See Engine Compartment Overview on page 6 ‑ 14 for the location of the engine oil dipstick. 1. T urn off the engine and give the oil several minutes to drain back into the oil pan. If this is not done, the oil dipstick might not show the actual level. 2. Pull the dipstick and clean it with a paper towel or cloth, then push it back in all the way . Remove it again, keeping the tip down and check the level. When to Add Engine Oil If the oil is below the MIN (mi[...]

What Kind of Engine Oil to Use Look for three things: . GM6094M Use only an oil that meets GM Standard GM6094M. . SAE 5W-30 SAE 5W-30 is best for the vehicle. These numbers on an oil container show its viscosity , or thickness. Do not use other viscosity oils such as SAE 20W-50. . American Petroleum Institute (API) starburst symbol Oils meeting these requirements should have the starburst symbol on the container . This symbol indicates that the oil has been certified by the American Petroleum Institute (API). Notice: Use only engine oil identified as meeting GM Standard GM6094M and showing the American Petroleum Institute Certified For Gasoline Engines starburst symbol. Failure to use the re[...]

Cold T emperature Operation If in an area of extreme cold, where the temperature falls below − 29°C ( − 20°F), use either an SAE 5W-30 synthetic oil or an SAE 0W-30 engine oil. Both provide easier cold starting for the engine at extremely low temperatures. Always use an oil that meets the required specification, GM6094M. See “ What Kind of Engine Oil to Use ” for more information. Engine Oil Additives / Engine Oil Flushes Do not add anything to the oil. The recommended oils with the starburst symbol that meet GM Standard GM6094M are all that is needed for good performance and engine protection. Engine oil system flushes are not recommended and could cause engine damage not covered [...]

How to Reset the Engine Oil Life System The Engine Oil Life System calculates when to change your engine oil and filter based on vehicle use. Whenever the oil is changed, reset the system so it can calculate when the next oil change is required. If a situation occurs where the oil is changed prior to a change engine oil light being turned on, reset the system. After changing the engine oil, the system must be reset: 1. With the engine off, turn the ignition key to ON/RUN. 2. Fully press and release the accelerator pedal slowly three times within five seconds. 3. T urn the key to LOCK/OFF , then start the vehicle. If the change engine oil light comes back on when the vehicle is started, the e[...]

T o inspect or replace the air cleaner/filter: 1. Remove the screws and lift off the cover . 2. Inspect or replace the engine air cleaner/filter . 3. Put the cover back on tightly and tighten the screws. See Scheduled Maintenance on page 7 ‑ 3 for replacement intervals. { W ARNING: Operating the engine with the air cleaner/filter off can cause you or others to be burned. The air cleaner not only cleans the air; it helps to stop flames if the engine backfires. Use caution when working on the engine and do not drive with the air cleaner/filter off. Notice: If the air cleaner/filter is off, dirt can easily get into the engine, which could damage it. Always have the air cleaner/filter in place[...]

How to Check Automatic T ransmission Fluid Because this operation can be a little difficult, you may choose to have this done at the dealer/retailer service department. If you do it yourself, be sure to follow all the instructions here, or you could get a false reading on the dipstick. Notice: T oo much or too little fluid can damage the transmission. T oo much can mean that some of the fluid could come out and fall on hot engine parts or exhaust system parts, starting a fire. T oo little fluid could cause the transmission to overheat. Be sure to get an accurate reading if checking the transmission fluid. W ait at least 30 minutes before checking the transmission fluid level if you have been[...]

Then, without shutting off the engine, follow these steps: 1. Locate the automatic transmission dipstick which is located toward the front of the engine compartment, near the power steering fluid reservoir . See Engine Compartment Overview on page 6 ‑ 14 for more information on location. 2. Pull out the dipstick and wipe it with a clean rag or paper towel. 3. Push the dipstick back in all the way , wait three seconds, and then pull it back out again. 4. Check both sides of the dipstick. The fluid should be between MIN (A) and MAX (B) mark of the hot area of the dipstick. 5. If the fluid level is in the acceptable range, push the dipstick back in all the way . How to Add Automatic T ransmis[...]

Manual T ransmission Fluid It is not necessary to check the transmission fluid level. A transmission fluid leak is the only reason for fluid loss. If a leak occurs, take the vehicle to the dealer/retailer service department and have it repaired as soon as possible. See Recommended Fluids and Lubricants on page 7 ‑ 1 1 for the proper fluid to use. Hydraulic Clutch There is one reservoir for both the brake and the hydraulic clutch fluid. See Brakes on page 6 ‑ 34 for more information. The hydraulic clutch linkage in the vehicle is self-adjusting. The master cylinder reservoir is filled with hydraulic fluid. A fluid loss in this system could indicate a problem. Have the system inspected and[...]

How to Check and Add Fluid The reservoir is located near the back of the engine compartment on the driver side of the vehicle. See Engine Compartment Overview on page 6 ‑ 14 for more information on location. T o check the fluid level, look on the side of the reservoir . If the fluid reaches the MAX (A) mark on the reservoir , the fluid level is correct. If the fluid does not reach the MIN (B) mark on the reservoir, then fluid needs to be added. Cooling System The cooling system allows the engine to maintain the correct working temperature. A. Electric Engine Cooling Fan B. Coolant Surge T ank with Pressure Cap 6-24[...]

{ W ARNING: An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury . Keep hands, clothing, and tools away from any underhood electric fan. { W ARNING: Heater and radiator hoses, and other engine parts, can be very hot. Do not touch them. If you do, you can be burned. Do not run the engine if there is a leak. If you run the engine, it could lose all coolant. That could cause an engine fire, and you could be burned. Get any leak fixed before you drive the vehicle. Notice: Using coolant other than DEX ‐ COOL ® can cause premature engine, heater core, or radiator corrosion. In addition, the engine coolant may require changing sooner[...]

What to Use { W ARNING: Adding only plain water to the cooling system can be dangerous. Plain water , or some other liquid such as alcohol, can boil before the proper coolant mixture will. The vehicle's coolant warning system is set for the proper coolant mixture. With plain water or the wrong mixture, the engine could get too hot but you would not get the overheat warning. The engine could catch fire and you or others could be burned. Use a 50/50 mixture of clean, drinkable water and DEX-COOL ® coolant. Use a 50/50 mixture of clean, drinkable water and DEX-COOL ® coolant. If using this mixture, nothing else needs to be added. This mixture: . Gives freezing protection down to − 34°[...]

If coolant is visible but the coolant level is not between the Minimum and Maximum marks, add a 50/50 mixture of clean, drinkable water and DEX-COOL ® coolant at the coolant surge tank, but be sure the cooling system is cool before this is done. See Engine Coolant on page 6 ‑ 25 for more information. The engine coolant surge tank is located in the rear of the engine compartment on the driver side of the vehicle. See Engine Compartment Overview on page 6 ‑ 14 for more information on location. { W ARNING: T urning the surge tank pressure cap when the engine and radiator are hot can allow steam and scalding liquids to blow out and burn you badly . Never turn the surge tank pressure cap —[...]

How to Add Coolant to the Coolant Surge T ank { W ARNING: Y ou can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol and it will burn if the engine parts are hot enough. Do not spill coolant on a hot engine. Notice: This vehicle has a specific coolant fill procedure. Failure to follow this procedure could cause the engine to overheat and be severely damaged. { W ARNING: An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury . Keep hands, clothing, and tools away from any underhood electric fan. { W ARNING: Steam and scalding liquids from a hot cooling system can blow out and burn you badly . They [...]

2. Then keep turning the pressure cap slowly and remove it. 3. Fill the coolant surge tank with the proper mixture to the Maximum mark on the coolant surge tank. W ait about five minutes, then check to see if the level is below the mark. If the level is below the Maximum mark, add additional coolant to bring the level up to the mark. Repeat this procedure until the level remains constant at the Maximum mark for at least five minutes. 6-29[...]

4. With the coolant surge tank pressure cap off, start the engine and let it run until you can feel the upper radiator hose getting hot. W atch out for the engine cooling fan. By this time, the coolant level inside the coolant surge tank may be lower . If the level is lower than the Maximum mark, add more of the proper mixture to the coolant surge tank until the level reaches the mark. 5. Replace the pressure cap. Be sure the pressure cap is hand-tight and fully seated. Notice: If the pressure cap is not tightly installed, coolant loss and possible engine damage may occur . Be sure the cap is properly and tightly secured. Engine Overheating The vehicle has an indicator to warn of the engine [...]

W ARNING: (Continued) If you keep driving when your engine is overheated, the liquids in it can catch fire. Y ou or others could be badly burned. Stop your engine if it overheats, and get out of the vehicle until the engine is cool. If No Steam Is Coming From The Engine Compartment If an engine overheat warning is displayed but no steam can be seen or heard, the problem may not be too serious. Sometimes the engine can get a little too hot when the vehicle: . Climbs a long hill on a hot day . . Stops after high-speed driving. . Idles for long periods in traffic. If the overheat warning is displayed with no sign of steam: 1. T urn the air conditioning off. 2. T urn the heater on to the highest[...]

Power Steering Fluid When to Check Power Steering Fluid The power steering fluid reservoir is located toward the front of the engine compartment on the driver's side of the vehicle. See Engine Compartment Overview on page 6 ‑ 14 for reservoir location. It is not necessary to regularly check power steering fluid unless you suspect there is a leak in the system or you hear an unusual noise. A fluid loss in this system could indicate a problem. Have the system inspected and repaired. How to Check Power Steering Fluid T urn the key off and let the engine compartment cool down. The level should be above the MIN mark on the reservoir . If the level drops below the MIN mark, add power steeri[...]

What to Use T o determine what kind of fluid to use, see Recommended Fluids and Lubricants on page 7 ‑ 1 1 . Always use the proper fluid. Failure to use the proper fluid can cause leaks and damage hoses and seals. Windshield W asher Fluid What to Use When you need windshield washer fluid, be sure to read the manufacturer's instructions before use. If you will be operating your vehicle in an area where the temperature may fall below freezing, use a fluid that has sufficient protection against freezing. Adding W asher Fluid Open the cap with the washer symbol on it. Add washer fluid until the tank is full. See Engine Compartment Overview on page 6 ‑ 14 for reservoir location. Notice: [...]

Brakes Brake Fluid The vehicle has one reservoir for both the brake and clutch hydraulic systems. It is filled with DOT 3 brake fluid. See Engine Compartment Overview on page 6 ‑ 14 for the location of the reservoir . There are only two reasons why the brake fluid level in the reservoir might go down: . The brake fluid level goes down because of normal brake lining wear . When new linings are installed, the fluid level goes back up. . A fluid leak in the brake or clutch hydraulic system can also cause a low fluid level. Have the brake or clutch hydraulic system fixed, since a leak means that sooner or later the brakes will not work well. Do not top off the brake fluid. Adding brake fluid d[...]

{ W ARNING: With the wrong kind of fluid in the brake or clutch hydraulic system, the brakes or clutch might not work well. This could cause a crash. Always use the proper brake fluid. Notice: . Using the wrong fluid can badly damage brake or clutch hydraulic system parts. For example, just a few drops of mineral-based oil, such as engine oil, in the brake or clutch hydraulic system can damage brake or clutch hydraulic system parts so badly that they will have to be replaced. Do not let someone put in the wrong kind of fluid. . If brake fluid is spilled on the vehicle's painted surfaces, the paint finish can be damaged. Be careful not to spill brake fluid on the vehicle. If you do, wash[...]

Properly torqued wheel nuts are necessary to help prevent brake pulsation. When tires are rotated, inspect brake pads for wear and evenly tighten wheel nuts in the proper sequence to torque specifications in Capacities and Specifications on page 6 ‑ 93 . If the vehicle has rear drum brakes, they do not have wear indicators, but if a rear brake rubbing noise is heard, have the rear brake linings inspected immediately . Rear brake drums should be removed and inspected each time the tires are removed for rotation or changing. When the front brake pads are replaced, have the rear brakes inspected, too. Brake linings should always be replaced as complete axle sets. Brake Pedal T ravel See your [...]

Battery Refer to the replacement number on the original battery label when a new battery is needed. See Engine Compartment Overview on page 6 ‑ 14 for battery location. { DANGER: Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. W ash hands after handling. V ehicle Storage { W ARNING: Batteries have acid that can burn you and gas that can explode. Y ou can be badly hurt if you are not careful. See Jump Starting on page 6 ‑ 38 for tips on working around a battery without getting hurt. Infrequent Usage: Remove the black, negative ( − ) cable from the battery to keep the batt[...]

Jump Starting If the vehicle's battery has run down, you may want to use another vehicle and some jumper cables to start your vehicle. Be sure to use the following steps to do it safely . { W ARNING: Batteries can hurt you. They can be dangerous because: . They contain acid that can burn you. . They contain gas that can explode or ignite. . They contain enough electricity to burn you. If you do not follow these steps exactly , some or all of these things can hurt you. Notice: Ignoring these steps could result in costly damage to the vehicle that would not be covered by the warranty . T rying to start the vehicle by pushing or pulling it will not work, and it could damage the vehicle. 1.[...]

Notice: If you leave the radio or other accessories on during the jump starting procedure, they could be damaged. The repairs would not be covered by the warranty . Always turn off the radio and other accessories when jump starting the vehicle. 3. T urn off the ignition on both vehicles. Unplug unnecessary accessories plugged into the cigarette lighter or the accessory power outlet. T urn off the radio and all lamps that are not needed. This will avoid sparks and help save both batteries. And it could save the radio! 4. Open the hoods and locate the batteries. Find the positive (+) and negative ( − ) terminal locations on each vehicle. See Engine Compartment Overview on page 6 ‑ 14 for m[...]

{ W ARNING: Fans or other moving engine parts can injure you badly . Keep your hands away from moving parts once the engine is running. 5. Check that the jumper cables do not have loose or missing insulation. If they do, you could get a shock. The vehicles could be damaged too. Before you connect the cables, here are some things you should know . Positive (+) will go to positive (+) or to a remote positive (+) terminal if the vehicle has one. Negative ( − ) will go to a heavy , unpainted metal engine part or to a remote negative ( − ) terminal if the vehicle has one. Do not connect positive (+) to negative ( − ) or you will get a short that would damage the battery and maybe other part[...]

7. Do not let the other end touch metal. Connect it to the positive (+) terminal of the good battery . Use a remote positive (+) terminal if the vehicle has one. 8. Now connect the black negative ( − ) cable to the negative ( − ) terminal of the good battery . Use a remote negative ( − ) terminal if the vehicle has one. Do not let the other end touch anything until the next step. The other end of the negative ( − ) cable does not go to the dead battery . It goes to a heavy , unpainted metal engine part or to a remote negative ( − ) terminal on the vehicle with the dead battery . 6-41[...]

9. Connect the other end of the negative ( − ) cable at least 18 inches (45 cm) away from the dead battery , but not near engine parts that move. The electrical connection is just as good there, and the chance of sparks getting back to the battery is much less. 10. Now start the vehicle with the good battery and run the engine for a while. 1 1. Try to start the vehicle that had the dead battery . If it will not start after a few tries, it probably needs service. Notice: If the jumper cables are connected or removed in the wrong order , electrical shorting may occur and damage the vehicle. The repairs would not be covered by the vehicle warranty . Always connect and remove the jumper cables[...]

T o disconnect the jumper cables from both vehicles, do the following: 1. Disconnect the black negative ( − ) cable from the vehicle that had the dead battery . 2. Disconnect the black negative ( − ) cable from the vehicle with the good battery . 3. Disconnect the red positive (+) cable from the vehicle with the good battery . 4. Disconnect the red positive (+) cable from the other vehicle. Headlamp Aiming Headlamp aim has been preset at the factory and should need no further adjustment. However , if your vehicle is damaged in a crash, the headlamp aim may be affected. Aim adjustment to the low-beam headlamps may be necessary if oncoming drivers flash their high-beam headlamps at you (fo[...]

Headlamps T o replace a headlamp bulb: 1. Open the hood. See Hood Release on page 6 ‑ 12 . 2. Remove the three bolts to remove the headlamp assembly . 3. Disconnect the wiring harness connector from the rear of the bulb. 4. Remove the headlamp cap. 5. Release the spring that retains the bulb by loosening the screw . 6. Remove the old bulb and install the new bulb. 7. Install the bulb retaining spring and tighten the screw . 8. Reinstall the headlamp cap. 9. Reconnect the wiring harness at the rear of the bulb. 6-44[...]

10. Reinstall the headlamp assembly using the three bolts. Front T urn Signal, Sidemarker and Parking Lamps T o replace a front turn signal or parking lamp bulb: 1. Open the hood. See Hood Release on page 6 ‑ 12 for more information. 2. Remove the three bolts to remove the headlamp assembly . 3. Disconnect the wiring harness connector from the rear of the bulb. 6-45[...]

4. T urn the front turn signal bulb socket counterclockwise. 5. Pull the front turn signal bulb socket out of the lamp housing. 6. Press the bulb inward and turn it counterclockwise to remove it from the bulb socket. 7. Install the new bulb into the socket by pressing it in and turning it clockwise. 8. Install the socket into the lamp housing by turning it clockwise. 9. Reconnect the wiring harness connector at the rear of the bulb. 10. Reinstall the headlamp assembly using the three bolts. 6-46[...]

Center High-Mounted Stoplamp (CHMSL) (Hatchback) T o replace a CHMSL bulb on the hatchback: 1. Open the liftgate. See Liftgate (Hatchback) on page 3 ‑ 10 for more information. 2. Pull down on the lamp assembly while holding the end of the bracket. 3. Remove the lens cover using a flat head screwdriver . 4. Remove the bulb by pulling it straight out of the bulb holder . 5. Install the new bulb. 6. Reverse Steps 1 through 3 to reinstall. Center High-Mounted Stoplamp (CHMSL) (Sedan) T o replace a CHMSL bulb on the sedan: 1. Open the trunk. See T runk on page 3 ‑ 8 for more information. 2. Remove the two screws and the lamp housing. Disconnect the wiring harness connector before removing the[...]

T aillamps, T urn Signal, Sidemarker , Stoplamps and Back-up Lamps T o replace a taillamp, turn signal lamp, stoplamp, or back-up bulb: 1. Open the liftgate or trunk. See Liftgate (Hatchback) on page 3 ‑ 10 or T runk on page 3 ‑ 8 . Hatchback Sedan 2. Remove the two screws and the lamp assembly . 3. T urn the bulb socket counterclockwise and remove the socket. 4. Press the bulb in and turn counterclockwise to remove from the socket. 5. Press the new bulb in and turn clockwise to install the bulb into the socket. 6. T urn the bulb socket clockwise to reinstall. 7. Reinstall the lamp assembly and two screws. 6-48[...]

License Plate Lamp T o replace one of these bulbs: 1. Remove the two screws holding each of the license plate lamps. 2. T urn and pull the license plate lamp toward you through the opening. 3. T urn the bulb socket counterclockwise and pull the bulb straight out of the socket. 4. Install the new bulb. 5. Push the bulb straight into the socket and turn clockwise to reinstall. 6. Push and turn the license plate lamp away from you through the opening. 7. Reinstall the two screws holding the license plate lamp. Replacement Bulbs Exterior Lamp Bulb Number Back-Up Lamps 94535571 Center High-Mounted Stoplamp (CHMSL) 94535587 Front Parking/T urn Signal Lamps 94535578 Front Sidemarker Lamps 94535578 [...]

Windshield Wiper Blade Replacement Windshield wiper blades should be inspected for wear or cracking. See “ Wiper Blade Check ” for more information. Replacement blades come in different types and are removed in different ways. For the proper type, see Maintenance Replacement Parts on page 7 ‑ 13 . Here is how to remove and replace the windshield wiper blade: 1. Pull the windshield wiper arm away from the windshield. 2. Press the retaining clip (A) and pull the wiper blade off the arm. 3. Install a new blade by reversing Steps 1 and 2. 6-50[...]

Tires Y our new vehicle comes with high-quality tires made by a leading tire manufact urer . If you ever have questions about your tire warranty and where to obtain service, see your vehicle W arranty booklet for details. For additional information refer to the tire manufacturer . { W ARNING: Poorly maintained and improperly used tires are dangerous. . Overloading your vehicle's tires can cause overheating as a result of too much flexing. Y ou could have an air-out and a serious accident. See Loading the V ehicle on page 5 ‑ 15 . (Continued) W ARNING: (Continued) . Underinflated tires pose the same danger as overloaded tires. The resulting accident could cause serious injury . Check a[...]

Tire Sidewall Labeling Useful information about a tire is molded into its sidewall. The examples below show a typical passenger car tire and a compact spare tire sidewall. Passenger Car Tire Example (A) Tire Size : The tire size is a combination of letters and numbers used to define a particular tire's width, height, aspect ratio, construction type and service description. See the “ Tire Size ” illustration later in this section for more detail. (B) DOT (Department of T ransportation) : The Department of Transportation (DOT) code indicates that the tire is in compliance with the U.S. Department of Transportation Motor V ehicle Safety Standards. (C) Tire Identification Number (TIN) :[...]

(F) Maximum Cold Inflation Load Limit : Maximum load that can be carried and the maximum pressure needed to support that load. For information on recommen ded tire pressure see Inflation - Tire Pressure on page 6 ‑ 58 and Loading the V ehicle on page 5 ‑ 15 . Compact Spare Tire Example (A) T emporary Use Only : The compact spare tire or temporary use tire has a tread life of approximately 3,000 miles (5 000 km) and should not be driven at speeds over 65 mph (105 km/h). The compact spare tire is for emergency use when a regular road tire has lost air and gone flat. See Compact Spare Tire on page 6 ‑ 78 and If a Tire Goes Flat on page 6 ‑ 69 . (B) Tire Ply Material : The type of cord a[...]

(D) Maximum Cold Inflation Load Limit : Maximum load that can be carried and the maximum pressure needed to support that load. See Compact Spare Tire on page 6 ‑ 78 and Loading the V ehicle on page 5 ‑ 15 . (E) Tire Inflation : The temporary use tire or compact spare tire should be inflated to 60 psi (420 kPa). For more information on tire pressure and inflation see Inflation - Tire Pressure on page 6 ‑ 58 . (F) Tire Size : A combination of letters and numbers define a tire's width, height, aspect ratio, construction type and service description. The letter T as the first character in the tire size means the tire is for temporary use only . Tire Size The following illustration sho[...]

(C) Aspect Ratio : A two ‐ digit number that indicates the tire height ‐ to ‐ width measurem ents. For example, if the tire size aspect ratio is 70, as shown in item C of the illustration, it would mean that the tire's sidewall is 70% as high as it is wide. (D) Construction Code : A letter code is used to indicate the type of ply construction in the tire. The letter R means radial ply construction; the letter D means diagonal or bias ply construction; and the letter B means belted ‐ bias ply construction. (E) Rim Diameter : Diameter of the wheel in inches. (F) Service Description : These characters represent the load index and speed rating of the tire. The load index represents [...]

Cold Tire Pressure : The amount of air pressure in a tire, measured in pounds per square inch (psi) or kilopascals (kPa) before a tire has built up heat from driving. See Inflation - Tire Pressure on page 6 ‑ 58 . Curb Weight : The weight of a motor vehicle with standard and optional equipment including the maximum capacity of fuel, oil, and coolant, but without passengers and cargo. DOT Markings : A code molded into the sidewall of a tire signifying that the tire is in compliance with the U.S. Department of Transportation (DOT) motor vehicle safety standards. The DOT code includes the T ire Identification Number (TIN), an alphanumeric designator which can also identify the tire manufactur[...]

Occupant Distribution : Designated seating positions. Outward Facing Sidewall : The side of an asymmetrical tire that has a particula r side that faces outward when mounted on a vehicle. The side of the tire that contains a whitewall, bears white lettering, or bears manufacture r , brand, and/or model name molding that is higher or deeper than the same moldings on the other sidewall of the tire. Passenger (P-Metric) Tire : A tire used on passenger cars and some light duty trucks and multipurpose vehicles. Recommended Inflation Pressure : V ehicle manufacturer's recommended tire inflation pressure as shown on the tire placard. See Inflation - Tire Pressure on page 6 ‑ 58 and Loading th[...]

V ehicle Maximum Load on the Tire : Load on an individual tire due to curb weight, accessory weight, occupant weight, and cargo weight. V ehicle Placard : A label permanently attached to a vehicle showing the vehicle's capacity weight and the original equipment tire size and recommended inflation pressure. See “ Tire and Loading Information Label ” under Loading the V ehicle on page 5 ‑ 15 . Inflation - Tire Pressure T ires need the correct amount of air pressure to operate effectively . Notice: Do not let anyone tell you that under ‐ inflation or over ‐ inflation is all right. It is not. If your tires do not have enough air (under ‐ inflation), you can get the following: . [...]

When to Check Check your tires once a month or more. Do not forget to check the compact spare tire, it should be at 60 psi (420 kPa). For additional information regarding the compact spare tire, see Compact Spare Tire on page 6 ‑ 78 . How to Check Use a good quality pocket-type gauge to check tire pressure. Y ou cannot tell if your tires are properly inflated simply by looking at them. Radial tires may look properly inflated even when they are under ‐ inflated. Check the tire's inflation pressure when the tires are cold. Cold means your vehicle has been sitting for at least three hours or driven no more than 1 mile (1.6 km). Remove the valve cap from the tire valve stem. Press the t[...]

Accordingly , when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under ‐ inflated tire causes the tire to overheat and can lead to tire failure. Under ‐ inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle's handling and stopping ability . Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver's responsibility to maintain correct tire pressure, even if under ‐ inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. Y our vehicle has also[...]

When a low tire pressure condition is detected, the TPMS illuminates the low tire pressure warning light on the instrument panel cluster . The low tire pressure warning light comes on at each ignition cycle until the tires are inflated to the correct inflation pressure. The tire pressure warning light may come on in cool weather when the vehicle is first started, and then turn off as you start to drive. This could be an early indicator that the tire pressures are getting low and need to be inflated to the proper pressure. A Tire and Loading Information label, attached to your vehicle, shows the size of your vehicle's original equipment tires and the correct inflation pressure for your v[...]

. Replacement tires or wheels do not match your vehicle's original equipment tires or wheels. T ires and wheels other than those recommended for your vehicle could prevent the TPMS from functioning properly . See Buying New Tires on page 6 ‑ 64 . . Operating electronic devices or being near facilities using radio wave frequencies similar to the TPMS could cause the TPMS sensors to malfunction. If the TPMS is not functioning it cannot detect or signal a low tire condition. See your dealer/retailer for service if the TPMS malfunction light comes on and stays on. TPMS Sensor Identification Codes Each TPMS sensor has a unique identification code. Any time you replace one or more of the TP[...]

When rotating your tires, always use the correct rotation pattern shown here. Do not include the compact spare tire in the tire rotation. After the tires have been rotated, adjust the front and rear inflation pressures as shown on the tire and loading information label. See Loading the V ehicle on page 5 ‑ 15 for an example of the tire and loading information label and where it is located on your vehicle. Make certain that all wheel nuts are properly tightened. See “ Wheel Nut T orque ” under Capacities and Specifications on page 6 ‑ 93 . { W ARNING: Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off[...]

When It Is Time for New T ires V arious factors, such as maintenance, temperatures, driving speeds, vehicle loading, and road conditions influence when you need new tires. One way to tell when it is time for new tires is to check the treadwear indicators, which will appear when your tires have only 1/16 inch (1.6 mm) or less of tread remaining. Y ou need new tires if any of the following statements are true: . Y ou can see the indicators at three or more places around the tire. . Y ou can see cord or fabric showing through the tire's rubber . . The tread or sidewall is cracked, cut, or snagged deep enough to show cord or fabric. . The tire has a bump, bulge, or split. . The tire has a p[...]

GM recommends replacing tires in sets of four . This is because uniform tread depth on all tires will help keep your vehicle performing most like it did when the tires were new . Replacing less than a full set of tires can affect the braking and handling performance of your vehicle. See Tire Inspection and Rotation on page 6 ‑ 62 . { W ARNING: Mixing tires could cause you to lose control while driving. If you mix tires of different sizes, brands, or types (radial and bias-belted tires), the vehicle may not handle properly , and you could have a crash. Using tires of different sizes, brands, or types may also cause damage to your vehicle. Be sure to use the correct size, brand, and type of [...]

Different Size Tires and Wheels If you add wheels or tires that are a different size than your original equipment wheels and tires, this may affect the way your vehicle performs, including its braking, ride and handling characteristics, stability , and resistance to rollover . Additionally , if your vehicle has electronic systems such as, antilock brakes, traction control, and electronic stability control, the performance of these systems can be affected. { W ARNING: If you add different sized wheels, your vehicle may not provide an acceptable level of performance and safety if tires not recommended for those wheels are selected. Y ou may increase the chance that you will crash and suffer se[...]

T readwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and a half (1½) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however , and may depart significantly from the norm due to variations in driving habits, service practices and differences in road characterist ics and climate. T raction — AA, A, B, C The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire's ability to stop on wet pavemen [...]

Wheel Alignment and Tire Balance The tires and wheels on your vehicle were aligned and balanced carefully at the factory to give you the longest tire life and best overall performance. Adjustments to wheel alignment and tire balancing will not be necessary on a regular basis. However , if you notice unusual tire wear or your vehicle pulling to one side or the other , the alignment might need to be checked. If you notice your vehicle vibrating when driving on a smooth road, the tires and wheels might need to be rebalanced. See your dealer/retailer for proper diagnosis. Wheel Replacement Replace any wheel that is bent, cracked, or badly rusted or corroded. If wheel nuts keep coming loose, the [...]

Notice: The wrong wheel can also cause problems with bearing life, brake cooling, speedometer or odometer calibration, headlamp aim, bumper height, vehicle ground clearance, and tire or tire chain clearance to the body and chassis. See Changing a Flat Tire on page 6 ‑ 70 for more information. Used Replacement Wheels { W ARNING: Putting a used wheel on the vehicle is dangerous. Y ou cannot know how it has been used or how far it has been driven. It could fail suddenly and cause a crash. If you have to replace a wheel, use a new GM original equipment wheel. Tire Chains Notice: Use tire chains only where legal and only when you must. Use only SAE Class “ S ” type chains that are the prope[...]

Get the vehicle under control by steering the way you want the vehicle to go. It may be very bumpy and noisy , but you can still steer . Gently brake to a stop, well off the road if possible. { W ARNING: Lifting a vehicle and getting under it to do maintenance or repairs is dangerous without the appropriate safety equipment and training. If a jack is provided with the vehicle, it is designed only for changing a flat tire. If it is used for anything else, you or others could be badly injured or killed if the vehicle slips off the jack. If a jack is provided with the vehicle, only use it for changing a flat tire. If a tire goes flat, the next part shows how to use the jacking equipment to chan[...]

When the vehicle has a flat tire (B), use the following example as a guide to assist you in the placement of wheel blocks (A). A. Wheel Block B. Flat T ire The following information explains how to use the jack and change a tire. Removing the Spare Tire and T ools The compact spare tire and tools you will need are located in the trunk. A. Jack B. Wheel Wrench C. Jack Handle D. Screwdriver (if equipped) 1. Open the trunk or liftgate. See T runk on page 3 ‑ 8 or Liftgate (Hatchback) on page 3 ‑ 10 . 2. Lift the trim cover . 6-71[...]

3. Remove the foam tray . 4. Remove the jack, the jack handle and the wheel wrench from the foam tray . 5. T urn the retainer counterclockwise and remove it from the compact spare. 6. Remove the compact spare tire. See Compact Spare Tire on page 6 ‑ 78 for more information. 6-72[...]

Removing the Flat Tire and Installing the Spare Tire 1. Do a safety check before proceeding. See Changing a Flat Tire on page 6 ‑ 70 . 2. If your vehicle has wheel covers, turn the four plastic caps counterclockwise by hand or by using the wheel wrench. The plastic nuts do not come off of the cover . 3. Remove the wheel cover using the flat end of the jack handle. Pry along the edge of the wheel cover until it comes off. Store the wheel cover in the cargo area until you have the flat tire repaired or replaced. 4. T urn the wheel nuts counterclockwise to loosen them. Do not remove them yet. 6-73[...]

Hatchback Sedan 5. Locate the notch in the frame near each wheel which the jack head fits in. 6. Position the jack and raise the jack head until it fits firmly into the notch in the vehicle's frame nearest the flat tire. 7. Put the compact spare tire near you. 6-74[...]

8. Insert the jack handle into the jack and the wheel wrench onto the end of the jack handle. { W ARNING: Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack, you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack. { W ARNING: Raising your vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall. T o help avoid personal injury and vehicle damage, be sure to fit the jack lift head into the proper location before raising the vehicle. 9. T urn the wheel wrench clockwise to raise the vehicle. Raise the vehicle far enough off the ground so there is enough room for the com[...]

10. T urn the wheel nuts counterclockwise to remove them. 1 1. Remove the flat tire. { W ARNING: Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident. When changing a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle. In an emergency , use a cloth or a paper towel to do this; but be sure to use a scraper or wire brush later , if needed, to get all the rust or dirt off. See Changing a Flat Tire on page 6 ‑ 70 . 12. Remove any rust or dirt from the wheel bolts, mounting surfaces and spare wheel. 13. Place the compact spare tire on the wheel-mounting surfac[...]

14. Install the wheel nuts with the rounded end of the nuts toward the wheel. Tighten each nut by hand clockwise until the wheel is held against the hub. 15. Lower the vehicle by turning the wheel wrench counterclockwise. Lower the jack completely . { W ARNING: Wheel nuts that are improperly or incorrectly tightened can cause the wheels to become loose or come off. The wheel nuts should be tightened with a torque wrench to the proper torque specification after replacing. Follow the torque specification supplied by the aftermarket manufacturer when using accessory locking wheel nuts. See Capacities and Specifications on page 6 ‑ 93 for original equipment wheel nut torque specifications. Not[...]

Storing a Flat or Spare Tire and T ools { W ARNING: Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury . In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place. T o store a flat or compact spare tire and tools: 1. Store the flat tire or the compact spare in the compact spare tire compartment. 2. Secure the retainer . 3. Store the tools securely in the foam tray and place the tray back in the cargo area. 4. Replace the trim cover . The compact spare tire is for temporary use only . Replace the compact spare tire with a full-size tire as soon as you can. See Compact Spare Tire on page 6 ‑[...]

Notice: When the compact spare is installed, do not take the vehicle through an automatic car wash with guide rails. The compact spare can get caught on the rails which can damage the tire, wheel and other parts of the vehicle. Do not use your compact spare on other vehicles. Do not mix your compact spare tire or wheel with other wheels or tires. Keep your spare tire and its wheel together . Notice: Tire chains will not fit the compact spare. Using them can damage the vehicle and can damage the chains too. Do not use tire chains on the compact spare. Appearance Care Interior Cleaning The vehicle's interior will continue to look its best if it is cleaned often. Although not always visibl[...]

Products that remove odors from the vehicle's upholstery and clean the vehicle's glass can be obtained from your dealer/retailer . Do not clean the vehicle using: . A knife or any other sharp object to remove a soil from any interior surface. . A stiff brush. It can cause damage to the vehicle's interior surfaces. . Heavy pressure or aggressive rubbing with a cleaning cloth. Use of heavy pressure can damage the interior and does not improve the effectivene ss of soil removal. . Laundry detergents or dishwashing soaps with degreasers can leave residue that streaks and attracts dirt. For liquid cleaners, about 20 drops per gallon (3.78 L) of water is a good guide. Use only mild,[...]

If any of the soil remains, a commercial fabric cleaner or spot lifter may be necessary . When a commercial upholstery cleaner or spot lifter is to be used, test a small hidden area for colorfastness first. If the locally cleaned area gives any impression that a ring formation may result, clean the entire surface. After the cleaning process has been completed, a paper towel can be used to blot excess moisture from the fabric or carpet. Leather A soft cloth dampened with water can be used to remove dust. If a more thorough cleaning is necessary , a soft cloth dampened with a mild soap solution can be used. Allow the leather to dry naturally . Do not use heat to dry . Never use steam to clean [...]

Care of Safety Belts Keep belts clean and dry . { W ARNING: Do not bleach or dye safety belts. It may severely weaken them. In a crash, they might not be able to provide adequate protection. Clean safety belts only with mild soap and lukewarm water . Weatherstrips Silicone grease on weatherstrips will make them last longer , seal better , and not stick or squeak. Apply silicone grease with a clean cloth. During very cold, damp weather frequent application may be required. W ashing Y our V ehicle The best way to preserve the vehicle's finish is to keep it clean by washing it often. Notice: Certain cleaners contain chemicals that can damage the emblems or nameplates on the vehicle. Check [...]

Finish Care Occasional waxing or mild polishing of the vehicle by hand may be necessary to remove residue from the paint finish. Approved cleaning products can be obtained from your dealer/retailer . If the vehicle has a basecoat/clearcoat paint finish, the clearcoat gives more depth and gloss to the colored basecoat. Always use waxes and polishes that are non-abrasive and made for a basecoat/clearcoat paint finish. Notice: Machine compounding or aggressive polishing on a basecoat/clearcoat paint finish may damage it. Use only non-abrasive waxes and polishes that are made for a basecoat/clearcoat paint finish on the vehicle. Foreign materials such as calcium chloride and other salts, ice mel[...]

Aluminum Wheels Notice: Using strong soaps, chemicals, abrasive polishes, cleaners, brushes, or cleaners that contain acid on aluminum or chrome-plated wheels, could damage the surface of the wheel(s). The repairs would not be covered by the vehicle warranty . Use only approved cleaners on aluminum or chrome-plated wheels. Keep the wheels clean using a soft clean cloth with mild soap and water . Rinse with clean water. After rinsing thoroughly , dry with a soft clean towel. A wax may then be applied. Notice: Using chrome polish on aluminum wheels could damage the wheels. The repairs would not be covered by the vehicle warranty . Use chrome polish on chrome wheels only . The surface of these [...]

Finish Damage Any stone chips, fractures or deep scratches in the finish should be repaired right away . Bare metal will corrode quickly and may develop into major repair expense. Minor chips and scratches can be repaired with touch-up materials available from your dealer/retailer . Larger areas of finish damage can be corrected in your dealer's/retailer's body and paint shop. Underbody Maintenance Chemicals used for ice and snow removal and dust control can collect on the underbody . If these are not removed, corrosion and rust can develop on the underbody parts such as fuel lines, frame, floor pan, and exhaust system even though they have corrosion protection. At least every spri[...]

V ehicle Identification V ehicle Identification Number (VIN) This legal identifier is in the front corner of the instrument panel, on the driver side. It can be seen through the windshield from outside. The VIN also appears on the V ehicle Certification and Service Parts labels and certificates of title and registration. Engine Identification The eighth character in the VIN is the engine code. This code identifies the vehicle's engine, specifications, and replacement parts. See “ Engine Specifications ” under Capacities and Specifications on page 6 ‑ 93 for the vehicle's engine code. Service Parts Identification Label This label, on the inside of the glove box, has the follow[...]

The vehicle has an airbag system. Before attempting to add anything electrical to the vehicle, see Servicing Y our Airbag-Equipped Vehicle on page 2 ‑ 70 and Adding Equipment to Y our Airbag-Equipped Vehicle on page 2 ‑ 71 . Headlamp Wiring The headlamp wiring is protected by fuses in the fuse block. An electrical overload will cause the lamps to turn off. If this happens, have the headlamp wiring checked right away . Windshield Wiper Fuses The windshield wiper motor is protected by a circuit breaker and a fuse. If the motor overheats due to heavy snow , etc., the wiper will stop until the motor cools. If the overload is caused by some electrical problem, have it fixed. Power Windows and[...]

Instrument Panel Fuse Block The instrument panel fuse block is located on the end of the instrument panel on the driver side of the vehicle. T o access the fuses, open the fuse panel door by pulling the door out. T o reinstall the door, first insert the rear edge of the fuse panel door , then push the front of the door into the end of the instrument panel to secure it. Fuses Usage AUDIO Audio, Clock, Immobilizer AUDIO/RKE A/C Switch, Clock, Power Mirror Unit, Audio, Anti-Theft Module, TPMS B/UP LAMP PNP Switch, Reverse Lamp Switch BLANK Not Used BLANK Not Used BLANK Not Used CIGAR Cigar Lighter 6-88[...]

Fuses Usage CLUSTER Brake Switch, TPMS, Anti ‐ Theft Module DEFOG MIRROR Power Mirror Unit, A/C Switch RR DEFOG Rear Defog DOOR LOCK Door Lock NA DRL NA DRL Circuit MIRROR/ SUNROOF Mirror Control Switch, Room Lamp, A/C Switch EMS 1 Engine Room Fuse Block, TCM, VSS, Fuel Pump EMS 2 Stoplamp Switch HORN Horn OBD DLC, Immobilizer CLUSTER/ ROOM LAMP T runk Room Lamp, Trunk Open Switch, IPC, Room Lamp SDM Sensing and Diagnostic Module Fuses Usage SOKET Power Jack STOP LAMP Brake Switch SUNROOF Sunroof Module (Option) T/SIG Hazard Switch WIPER Wiper Switch, Wiper Motor Engine Compartment Fuse Block The engine compartment fuse block is located on the driver side of the vehicle, near the battery .[...]

Fuses Usage F AN HI Cooling Fan HI Relay ABS ‐ 1 EBCM ABS ‐ 2 EBCM Fuses Usage SJB BA TT Instrument Panel Fuse Block ACC/IG1 IGN1 Relay IG2/ST IGN2 Relay , Starter Relay 6-90[...]

Fuses Usage ACC/RAP Instrument Panel Fuse Block P/WINDOW ‐ 2 Power Window Switch P/W WINDOW ‐ 1 Power Window Switch F AN LOW Cooling Fan LOW Relay A/CON A/C Compressor Relay PKLP LH T ail Lamp (LH), Side Marker (LH), T urn Signal & Parking Lamp (LH), License Lamp PKLP RH T ail Lamp (RH), Side Marker (RH), T urn Signal & Parking Lamp (RH), License Lamp, I/P Fuse Block ECU ECM, TCM FRT FOG Front Fog Lamp Relay F/PUMP Fuel Pump Relay Fuses Usage HAZARD Hazard Switch, Hood Contact Switch HDLP HI LH Head Lamp (LH), IPC HDLP HI RH Head Lamp (RH) IPC IPC HDLP LO LH Head Lamp (LH), I/P Fuse Block HDLP LO RH Head Lamp (RH) EMS ‐ 1 ECM, Injector DLIS Ignition Switch EMS ‐ 2 EV AP Canis[...]

Relays Usage F/PUMP RELA Y Fuel Pump ST ARTER RELA Y Starter P ARK LAMP RELA Y Park Lamp FRONT FOG RELA Y Fog Lamp HDLP HIGH RELA Y Head Lamp High HDLP LOW RELA Y Head Lamp Low F AN HIGH RELA Y Cooling Fan High Relays Usage F AN LOW RELA Y Cooling Fan Low A/CON RELA Y Air Conditioner ENGINE MAIN RELA Y Main Power ACC/RAP RELA Y I/P Fuse Block IGN ‐ 2 RELA Y Ignition Misc. Usage FUSE PULLER Fuse Puller 6-92[...]

Capacities and Specifications The following approximate capacities are given in English and metric conversions. See Recommended Fluids and Lubricants on page 7 ‑ 1 1 for more information. Application Capacities English Metric Air Conditioning Refrigerant R134a For the air conditioning system refrigerant charge amount, see the refrigerant caution label located under the hood. See your dealer/retailer for more information. Cooling System 6.7 qt 6.3 L Engine Oil with Filter 4.8 qt 4.5 L Fuel T ank 1 1.9 gal 45.0 L T ransmission, Automatic 6.2 qt 5.87 L T ransmission, Manual 1.9 qt 1.8 L Wheel Nut T orque 81 lb ft 1 10 Y All capacities are approximate. When adding, be sure to fill to the appro[...]

2 NOTES 6-94[...]

Section 7 Maintenance Schedule Maintenance Schedule .. ........... .............. . 7-2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Scheduled Maintenance . . . . . . . . . . . . . . . . . . . . . . . . 7-3 Owner Checks and Services . . . . . . . . . . . . . . . . . . . . 7-9 Recommended Fluids and Lubricants . . . . . . . . . . 7-1 1 Maintenance Replacement Parts . . . . . . . . . . . . . . 7-13 Engine Drive Belt Routing . . . . . . . . . . . . . . . . . . . . . 7-14 Maintenance Record . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-15 7-1[...]

Maintenance Schedule Introduction Notice: Maintenance intervals, checks, inspections, recommended fluids, and lubricants are necessary to keep this vehicle in good working condition. Damage caused by failure to follow scheduled maintenance might not be covered by the vehicle warranty . As the vehicle owner , you are responsible for the scheduled maintenance in this section. We recommend having your dealer/retailer perform these services. Proper vehicle maintenance helps to keep the vehicle in good working condition, improves fuel economy , and reduces vehicle emissions for better air quality . Because of all the different ways people use vehicles, maintenance needs vary . The vehicle might n[...]

At your dealer/retailer , you can be certain that you will receive the highest level of service available. Y our dealer/retailer has specially trained service technicians, uses genuine replacement parts, as well as, up to date tools and equipment to ensure fast and accurate diagnostics. The proper replacement parts, fluids, and lubricants to use are listed in Recommended Fluids and Lubricants on page 7 ‑ 1 1 and Maintenance Replacement Parts on page 7 ‑ 13 . We recommend the use of genuine parts from your dealer/retailer . Rotation of New Tires T o maintain ride, handling, and performance of the vehicle, it is important that the first rotation service for new tires be performed when they[...]

When the change engine oil light displays, certain services, checks, and inspections are required. The services described for Maintenance I should be performed at every engine oil change. The services described for Maintenance II should be performed when: . Maintenance I was performed the last time the engine oil was changed. . It has been 10 months or more since the change engine oil light has displayed or since the last service. Maintenance I . Change engine oil and filter . See Engine Oil on page 6 ‑ 15 . An Emission Control Service. . Engine coolant level check. See Engine Coolant on page 6 ‑ 25 . . Windshield washer fluid level check. See Windshield Washer Fluid on page 6 ‑ 33 . .[...]

. Body hinges and latches, key lock cylinders, and trunk lid hinges and latches lubrication. See Recommended Fluids and Lubricants on page 7 ‑ 1 1 . More frequent lubrication may be required when vehicle is exposed to a corrosive environment. Applying silicone grease on weatherstrips with a clean cloth makes them last longer , seal better , and not stick or squeak. . Restraint system component check. See Checking the Restraint Systems on page 2 ‑ 72 . . Automatic transmission fluid level check and adding fluid, if needed. See Automatic T ransmission Fluid on page 6 ‑ 20 . . Engine air cleaner filter inspection. See Engine Air Cleaner/Filter on page 6 ‑ 19 . . Passenger compartment ai[...]

Once a Month . T ire inflation check. See Inflation - Tire Pressure on page 6 ‑ 58 . . T ire wear inspection. See Tire Inspection and Rotation on page 6 ‑ 62 . Once a Y ear . Starter switch check. See Owner Checks and Services on page 7 ‑ 9 . . Parking brake and automatic transmission P (Park) mechanism check. See Owner Checks and Services on page 7 ‑ 9 . . Automatic transmission shiftlock control system check. See Owner Checks and Services on page 7 ‑ 9 . . Ignition transmission lock check. See Owner Checks and Services on page 7 ‑ 9 . . Engine cooling system and pressure cap pressure check. Radiator and air conditioning condenser outside cleaning. See Cooling System on page 6 ?[...]

First Engine Oil Change After Every 80 000 km/50,000 Miles . Automatic transmission fluid and filter change (severe service only) for vehicles mainly driven in heavy city traffic in hot weather , in hilly or mountainous terrain, when frequently towing a trailer , or used for taxi, police, or delivery service. See Automatic T ransmission Fluid on page 6 ‑ 20 . . Power steering pump accessory drive belt replacement. . Evaporative control system inspection. Check all fuel and vapor lines and hoses for proper hook ‐ up, routing, and condition. EV AP vent solenoid valve replacement. An Emission Control Service. The U.S. Environmental Protection Agency or the California Air Resources Board has[...]

Scheduled Maintenance Service Maintenance I Maintenance II Change engine oil and filter . Reset oil life system. • • Engine coolant level check. • • Windshield washer fluid level check. • • T ire inflation pressures check. • • T ire wear inspection. • • Rotate tires. • • Fluids visual leak check. • • Engine air cleaner filter inspection (vehicles driven in dusty conditions only). • • Brake system inspection. • • Steering and suspension inspection. • Engine cooling system inspection. • Windshield wiper blades inspection. • Body components lubrication. • Restraint system components check. • Automatic transmission fluid level check. • Engine air c[...]

Owner Checks and Services Starter Switch Check { W ARNING: When you are doing this inspection, the vehicle could move suddenly . If the vehicle moves, you or others could be injured. 1. Before starting this check, be sure there is enough room around the vehicle. 2. Firmly apply both the parking brake and the regular brake. See Parking Brake on page 3 ‑ 28 . Do not use the accelerator pedal, and be ready to turn off the engine immediately if it starts. 3. For automatic transmission vehicles, try to start the engine in each gear . The starter should work only in P (Park) or N (Neutral). If the starter works in any other position, your vehicle needs service. For manual transmission vehicles, [...]

Automatic T ransmission Shift Lock Control System Check { W ARNING: When you are doing this inspection, the vehicle could move suddenly . If the vehicle moves, you or others could be injured. 1. Before starting this check, be sure there is enough room around the vehicle. It should be parked on a level surface. 2. Firmly apply the parking brake. See Parking Brake on page 3 ‑ 28 . Be ready to apply the regular brake immediately if the vehicle begins to move. 3. With the engine off, turn the ignition to ON/RUN, but do not start the engine. Without applying the regular brake, try to move the shift lever out of P (Park) with normal effort. If the shift lever moves out of P (Park), contact your [...]

Parking Brake and Automatic T ransmission P (Park) Mechanism Check { W ARNING: When you are doing this check, the vehicle could begin to move. Y ou or others could be injured and property could be damaged. Make sure there is room in front of the vehicle in case it begins to roll. Be ready to apply the regular brake at once should the vehicle begin to move. Park on a fairly steep hill, with the vehicle facing downhill. Keeping your foot on the regular brake, set the parking brake. . T o check the parking brake's holding ability: With the engine running and the transmission in N (Neutral), slowly remove foot pressure from the regular brake pedal. Do this until the vehicle is held by the p[...]

Usage Fluid/Lubricant Automatic T ransmission Use only T -IV Automatic T ransmission Fluid (GM Part No. U.S. 88900925, in Canada 22689186). Manual T ransmission Manual Transmission Fluid (GM Part No. U.S. 89021806, in Canada 89021807). Key Lock Cylinders Multi-Purpose Lubricant, Superlube (GM Part No. U.S. 12346241, in Canada 10953474). Manual T ransmission Shift Linkage Chassis Lubricant (GM Part No. U.S. 12377985, in Canada 88901242) or lubricant meeting requirements of NLGI #2, Category LB or GC-LB. Chassis Lubrication Chassis Lubricant (GM Part No. U.S. 12377985, in Canada 88901242) or lubricant meeting requirements of NLGI #2, Category LB or GC-LB. Usage Fluid/Lubricant Hood Latch Assem[...]

Maintenance Replacement Parts Replacement parts identified below by name, part number , or specification can be obtained from your dealer/retailer . Maintenance Replacement Parts Part GM Part Number ACDelco Part Number Engine Air Cleaner/Filter 96536696 A3081C Engine Oil Filter 93185674 — Passenger Compartment Air Filter 96962173 — Spark Plugs 964761 19 — Wiper Blades - Hatchback Driver Side 96476652 — Passenger Side 96476656 — Rear 96301840 — Wiper Blades - Sedan Driver Side 96476652 — Passenger Side 96476656 — 7-13[...]

Engine Drive Belt Routing 7-14[...]

Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided. Retain all maintenance receipts. Maintenance Record Date Odometer Reading Serviced By Services Performed 7-15[...]

Maintenance Record (cont'd) Date Odometer Reading Serviced By Services Performed 7-16[...]

Maintenance Record (cont'd) Date Odometer Reading Serviced By Services Performed 7-17[...]

Maintenance Record (cont'd) Date Odometer Reading Serviced By Services Performed 7-18[...]

Section 8 Customer Assistance Information Customer Assistance and Information . . . . . . . . . . . 8-2 Customer Satisfaction Procedure . . . . . . . . . . . . . . . 8-2 Online Owner Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5 Customer Assistance for T ext T elephone (TTY) Users . . . . . . . . . . . . . . 8-6 Customer Assistance Offices . . . . . . . . . . . . . . . . . . . 8-6 GM Mobility Reimbursement Program . . . . . . . . . . . 8-7 Roadside Assistance Program . . . . . . . . . . . . . . . . . . 8-7 Scheduling Service Appointments . . . . . . . . . . . . . 8-10 Courtesy T ransportation Program . . . . . . . . . . . . . . 8-10 Collision Damage Repair . . . . . . . [...]

Customer Assistance and Information Customer Satisfaction Procedure Y our satisfaction and goodwill are important to your dealer and to Chevrolet. Normally , any concerns with the sales transaction or the operation of the vehicle will be resolved by the dealer's sales or service departments. Sometimes, however , despite the best intentions of all concerned, misunderstandings can occur . If your concern has not been resolved to your satisfaction, the following steps should be taken: STEP ONE: Discuss your concern with a member of dealership management. Normally , concerns can be quickly resolved at that level. If the matter has already been reviewed with the sales, service, or parts mana[...]

STEP THREE — U.S. Owners: Both General Motors and your dealer are committed to making sure you are completely satisfied with your new vehicle. However , if you continue to remain unsatisfied after following the procedure outlined in Steps One and T wo, you can file with the Better Business Bureau (BBB) Auto Line Program to enforce your rights. The BBB Auto Line Program is an out of court program administered by the Council of Better Business Bureaus to settle automotive disputes regarding vehicle repairs or the interpretation of the New V ehicle Limited W arranty . Although you may be required to resort to this informal dispute resolution program prior to filing a court action, use of the [...]

STEP THREE — Canadian Owners: In the event that you do not feel your concerns have been addressed after following the procedure outlined in Steps 1 and 2, General Motors of Canada Limited wants you to be aware of its participation in a no-charge Mediation/Arbitration Program. General Motors of Canada Limited has committed to binding arbitration of owner disputes involving factory-related vehicle service claims. The program provides for the review of the facts involved by an impartial third party arbiter , and may include an informal hearing before the arbiter . The program is designed so that the entire dispute settlement process, from the time you file your complaint to the final decision[...]

Online Owner Center Online Owner Center (U.S.) — www .gmownercenter .com/chevrolet Information and services customized for your specific vehicle — all in one convenient place. . Digital owner manual, warranty information, and more . Online service and maintenance records . Find Chevrolet dealers for service nationwide . Exclusive privileges and offers . Recall notices for your specific vehicle . OnStar ® and GM Cardmember Services Earnings summaries Other Helpful Links: Chevrolet — www .chevrolet.com Chevrolet Merchandise — www .chevymall.com Help Center — www .chevrolet.com/helpcenter . F AQ . Contact Us My GM Canada (Canada) — www .gm.ca My GM Canada is a password-protected se[...]

Customer Assistance for T ext T elephone (TTY) Users T o assist customers who are deaf, hard of hearing, or speech-impaired and who use T ext T elephones (TTYs), Chevrolet has TTY equipment available at its Customer Assistance Center . Any TTY user in the U.S. can communicate with Chevrolet by dialing: 1-800-833-CHEV (2438). (TTY users in Canada can dial 1-800-263-3830.) Customer Assistance Offices Chevrolet encourages customers to call the toll-free number for assistance. However , if a customer wishes to write or e-mail Chevrolet, the letter should be addressed to: United States — Customer Assistance Chevrolet Motor Division Chevrolet Customer Assistance Center P .O. Box 33170 Detroit, M[...]

Mexico, Central America and Caribbean Islands/Countries (Except Puerto Rico and U.S. Virgin Islands) — Customer Assistance General Motors de Mexico, S. de R.L. de C.V . Customer Assistance Center Paseo de la Reforma # 2740 Col. Lomas de Bezares C.P . 1 1910, Mexico, D.F . 01-800-508-0000 Long Distance: 01 1-52-53 29 0 800 GM Mobility Reimbursement Program This program, available to qualified applicants, can reimburse you up to $1,000 of the cost of eligible aftermarket adaptive equipment required for your vehicle, such as hand controls or a wheelchair/scooter lift. The offer is available for a very limited period of time from the date of vehicle purchase/lease. For more details, or to dete[...]

. Model, year , color , and license plate number of the vehicle . Odometer reading, V ehicle Identification Number (VIN), and delivery date of the vehicle . Description of the problem Coverage Services are provided up to 5 years/100,000 miles (160 000 km), whichever comes first. In the U.S., anyone driving the vehicle is covered. In Canada, a person driving the vehicle without permission from the owner is not covered. Roadside Assistance is not a part of the New V ehicle Limited W arranty . Chevrolet and General Motors of Canada Limited reserve the right to make any changes or discontinue the Roadside Assistance program at any time without notification. Chevrolet and General Motors of Canada[...]

Services Not Included in Roadside Assistance . Impound towing caused by violation of any laws. . Legal fines. . Mounting, dismounting or changing of snow tires, chains, or other traction devices. . T owing or services for vehicles driven on a non-public road or highway . Services Specific to Canadian Purchased V ehicles . Fuel delivery: Reimbursement is approximately $5 Canadian. Diesel fuel delivery may be restricted. Propane and other fuels are not provided through this service. . Lock-Out Service: V ehicle registration is required. . T rip Routing Service: Detailed maps of North America are provided when requested either with the most direct route or the most scenic route. There is a limi[...]

Scheduling Service Appointments When your vehicle requires warranty service, contact your dealer/retailer and request an appointment. By scheduling a service appointment and advising your service consultant of your transportation needs, your dealer/retailer can help minimize your inconvenience. If your vehicle cannot be scheduled into the service department immediately , keep driving it until it can be scheduled for service, unless, of course, the problem is safety-related. If it is, please call your dealership/retailer , let them know this, and ask for instructions. If the dealer/retailer requests you to bring the vehicle for service, you are urged to do so as early in the work day as possi[...]

T ransportation Options W arranty service can generally be completed while you wait. However , if you are unable to wait, GM helps to minimize your inconvenience by providing several transportation options. Depending on the circumstances, your dealer can offer you one of the following: Shuttle Service Shuttle service is the preferred means of offering Courtesy Transportation. Dealers may provide you with shuttle service to get you to your destination with minimal interruption of your daily schedule. This includes one ‐ way or round trip shuttle service within reasonable time and distance parameters of the dealer's area. Public T ransportation or Fuel Reimbursement If your vehicle requ[...]

Additional Program Information All program options, such as shuttle service, may not be available at every dealer . Please contact your dealer for specific information about availability . All Courtesy T ransportation arrangements will be administered by appropriate dealer personnel. General Motors reserves the right to unilaterally modify , change or discontinue Courtesy T ransportation at any time and to resolve all questions of claim eligibility pursuant to the terms and conditions described herein at its sole discretion. Collision Damage Repair If your vehicle is involved in a collision and it is damaged, have the damage repaired by a qualified technician using the proper equipment and q[...]

Aftermarket collision parts are also available. These are made by companies other than GM and may not have been tested for your vehicle. As a result, these parts may fit poorly , exhibit premature durability/corrosion problems, and may not perform properly in subsequent collisions. Aftermarket parts are not covered by your GM New V ehicle Limited Warranty , and any vehicle failure related to such parts are not covered by that warranty . Repair Facility We recommend that you choose a collision repair facility that meets your needs before you ever need collision repairs. Y our dealer/retailer may have a collision repair center with GM-trained technicians and state of the art equipment, or be a[...]

If a Crash Occurs Here is what to do if you are involved in a crash. . Check to make sure that you are all right. If you are uninjured, make sure that no one else in your vehicle, or the other vehicle, is injured. . If there has been an injury , call emergency services for help. Do not leave the scene of a crash until all matters have been taken care of. Move your vehicle only if its position puts you in danger or you are instructed to move it by a police officer . . Give only the necessary and requested information to police and other parties involved in the crash. Do not discuss your personal condition, mental frame of mind, or anything unrelated to the crash. This will help guard against [...]

Managing the V ehicle Damage Repair Process In the event that your vehicle requires damage repairs, GM recommends that you take an active role in its repair . If you have a pre-determined repair facility of choice, take your vehicle there, or have it towed there. Specify to the facility that any required replacement collision parts be original equipment parts, either new Genuine GM parts or recycled original GM parts. Remember , recycled parts will not be covered by your GM vehicle warranty . Insurance pays the bill for the repair , but you must live with the repair . Depending on your policy limits, your insurance company may initially value the repair using aftermarket parts. Discuss this [...]

Reporting Safety Defects to the Canadian Government If you live in Canada, and you believe that your vehicle has a safety defect, notify Transport Canada immediately , in addition to notifying General Motors of Canada Limited. Call them at 1-800-333-0510 or write to: T ransport Canada Road Safety Branch 2780 Sheffield Road Ottawa, Ontario K1B 3V9 Reporting Safety Defects to General Motors In addition to notifying NHTSA (or T ransport Canada) in a situation like this, please notify General Motors. Call 1-800-222-1020, or write: Chevrolet Motor Division Chevrolet Customer Assistance Center P .O. Box 33170 Detroit, MI 48232-5170 In Canada, call 1-800-263-3777 (English) or 1-800-263-7854 (French[...]

Service Publications Ordering Information Service Manuals Service Manuals have the diagnosis and repair information on engines, transmission, axle suspension, brakes, electrical, steering, body , etc. Service Bulletins Service Bulletins give additional technical service information needed to knowledgeably service General Motors cars and trucks. Each bulletin contains instructions to assist in the diagnosis and service of your vehicle. Owner Information Owner publications are written specifically for owners and intended to provide basic operational information about the vehicle. The owner manual includes the Maintenance Schedule for all models. In-Portfolio: Includes a Portfolio, Owner Manual[...]

V ehicle Data Recording and Privacy Y our GM vehicle has a number of sophisticated computers that record information about the vehicle ’ s performance and how it is driven. For example, your vehicle uses computer modules to monitor and control engine and transmission performance, to monitor the conditions for airbag deployment and deploy airbags in a crash and, if so equipped, to provide antilock braking to help the driver control the vehicle. These modules may store data to help your dealer/retailer technician service your vehicle. Some modules may also store data about how you operate the vehicle, such as rate of fuel consumption or average speed. These modules may also retain the owner [...]

Important: EDR data is recorded by your vehicle only if a non-trivial crash situation occurs; no data is recorded by the EDR under normal driving conditions and no personal data (e.g., name, gender , age, and crash location) is recorded. However , other parties, such as law enforcement, could combine the EDR data with the type of personally identifying data routinely acquired during a crash investigation. T o read data recorded by an EDR, special equipment is required, and access to the vehicle or the EDR is needed. In addition to the vehicle manufacturer , other parties, such as law enforcement, that have the special equipment, can read the information if they have access to the vehicle or [...]

Radio Frequency Identification (RFID) RFID technology is used in some vehicles for functions such as tire pressure monitoring and ignition system security , as well as in connection with conveniences such as key fobs for remote door locking/unlocking and starting, and in-vehicle transmitters for garage door openers. RFID technology in GM vehicles does not use or record personal information or link with any other GM system containing personal information. Radio Frequency Statement This vehicle has systems that operate on a radio frequency that comply with Part 15 of the Federal Communications Commission (FCC) Rules and with RSS-210/21 1 of Industry and Science Canada. Operation is subject to [...]

A Accessories and Modifications . . . . . . . . . . . . . . . . . . . . . . .6-4 Accessory Power Outlets . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14 Add-On Electrical Equipment . . . . . . . . . . . . . . . . . . . . . . 6-86 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7 Air Cleaner/Filter , Engine . . . . . . . . . . . . . . . . . . . . . . . . . . 6-19 Air Conditioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16 Air Filter , Passenger Compartment . . . . . . . . . . . . . . . . 4-19 Airbag Adding Equipment to Y our Airbag-Equipped V ehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . [...]

Audio System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-39 Audio Steering Wheel Controls . . . . . . . . . . . . . . . . . . . 4-64 Radio Reception . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-65 Radio with CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-45 Radio with Six-Disc CD . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-53 Automatic Transmission Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-20 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23 B Backglass Antenna . . . . . . . . . . . . . . [...]

Care of Safety Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-82 CD, MP3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-61 Center High-Mounted Stoplamp (CHMSL) . . . . . . . . . 6-47 Central Door Unlock System . . . . . . . . . . . . . . . . . . . . . . . . . 3-6 Chains, T ire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-69 Charging System Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-27 Check Engine Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-31 Checking Things Under the Hood . . . . . . . . . . . . . . . . . . 6-1 1 Chemical P[...]

Coolant Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-25 Engine T emperature Gauge . . . . . . . . . . . . . . . . . . . . . . 4-30 Cooling System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-24 Courtesy T ransportation Program . . . . . . . . . . . . . . . . . . 8-10 Cruise Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-8 Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-35 Cupholders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-36 Customer Assistance . . . . . . . . . . . . . . . . . . [...]

E EDR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-18 Electrical Equipment, Add-On . . . . . . . . . . . . . . . . . . . . . 6-86 Electrical System Engine Compartment Fuse Block . . . . . . . . . . . . . . . . . 6-89 Fuses and Circuit Breakers . . . . . . . . . . . . . . . . . . . . . . . 6-87 Headlamp Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-87 Instrument Panel Fuse Block . . . . . . . . . . . . . . . . . . . . . 6-88 Power Windows and Other Power Options . . . . . . . 6-87 Windshield Wiper Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . 6-87 Engine Air Cleaner/Filter . . . . . . . . . . . . . . .[...]

Fuel (cont.) Gasoline Octane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6 Gasoline Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7 Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-36 Low Fuel W arning Light . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-37 Fuel Economy Driving for Better . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-25 Fuses Engine Compartment Fuse Block . . . . . . . . . . . . . . . . . 6-89 Fuses and Circuit Breakers . . . . . . . . . . . . . . . . . . . . . . . 6-87 Instrument Panel Fuse Block . . . . . . . . . . . . . . . . . . . . . 6-88 [...]

I Ignition Positions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18 Immobilizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14 Inadvertent Power Battery Saver . . . . . . . . . . . . . . . . . . 4-13 Infants and Y oung Children, Restraints . . . . . . . . . . . . 2-35 Inflation - T ire Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-58 Instrument Panel Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13 Instrument Panel Cluster . . . . . . . . . . . . . . . . . . . . . . . . . . 4-22 Integrated T railer Brake Control System (ITBC) . . . . 5-23 Introduction . . . . . [...]

Lights (cont.) Flash-to-Pass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 Fog Lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-35 High/Low Beam Changer . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 Highbeam On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-35 Hold Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-29 Low Fuel W arning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-37 Oil Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-33 Passenger Airbag Status Indicator . . . . . . . . . .[...]

N New V ehicle Break-In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17 O Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-23 T rip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-23 Off-Road Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7 Oil Change Engine Oil Light . . . . . . . . . . . . . . . . . . . . . . . . . . 4-34 Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-15 Engine Oil Life System . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-18 Pressure Light . . . . . . . . . [...]

R Radio Frequency Identification (RFID) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-20 Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-20 Radios AM-FM Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-40 Radio with CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-45 Radio with Six-Disc CD . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-53 Reception . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-65 Rear Door Security Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7 Rear Seat Operation . . . . . . . . . . . . . . . .[...]

Safety Defects Reporting Canadian Government . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-16 General Motors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-16 U.S. Government . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-15 Safety W arnings and Symbols . . . . . . . . . . . . . . . . . . . . . . . . iv Scheduled Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3 Scheduling Appointments . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10 Seats Driver Seat Height Adjuster . . . . . . . . . . . . . . . . . . . . . . . . 2-5 Head Restraints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [...]

T T achometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-23 T aillamps T urn Signal, Sidemarker , Stoplamps, and Back-Up Lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-48 T ext T elephone (TTY) Users . . . . . . . . . . . . . . . . . . . . . . . . .8-6 Theft-Deterrent Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14 Content Theft-Deterrent . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15 Immobilizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14 T ilt Wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 T ime . . . . . . [...]

T ransmission Operation, Manual . . . . . . . . . . . . . . . . . . 3-26 T ransportation Program, Courtesy . . . . . . . . . . . . . . . . . 8-10 T rip Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-38 T rip Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-23 T runk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-8 T urn and Lane-Change Signals . . . . . . . . . . . . . . . . . . . . . . 4-4 T urn Signal/Multifunction Lever . . . . . . . . . . . . . . . . . . . . . . 4-4 U Uniform T ire Quality Grading . . . . . . . . . . . . . . . . . . . . . . 6-66 Up-Shift Light . . .[...]

Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12 Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13 Windshield W asher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7 W asher Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-33 Wiper Blade Replacement . . . . . . . . . . . . . . . . . . . . . . . . 6-50 Windshield (cont.) Wiper Blades, Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-83 Wiper Fuses . . . . . . [...]