Cisco Systems ONS 15600 SDH manual

CH A P T E R 18-1 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 18 DLPs F300 to F399 DLP-F300 Install Fiber-Optic Cables for SNCP Configurations Caution T o a void loss of traf f ic, do not create an SNCP usi ng two por ts on the same card. Y ou can create an SNCP on dif ferent ports on the same side of t he shelf, but Cisco r ecommends us[...]

18-2 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F301 Edit SNCP Dual-Ring Interconnect Circuit Hold-Off Timer DLP-F301 Edit SNCP Dual-Ring Interconnect Circuit Hold-Off Timer Note Cisco recommends that you set the DRI port HO T v a lue to zero and the circuit path selector HO T v alue to a number equal t[...]

18-3 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F303 Delete Overhead Circuits Step 1 From the V iew menu, choose Go to Netw ork V iew . Step 2 Click the Pro visioning > Overhead Cir cuits tabs. Step 3 Click the circuit tunnel that y ou want to con vert. Step 4 Click Edit . Step 5 In the Edit Circuit [...]

18-4 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F304 Repair an IP Tunnel DLP-F304 Repair an IP Tunnel Step 1 Obtain the original IP address of t h e node in question. Step 2 From the V iew menu, choose Go to Netw ork View . Step 3 From the T ools menu , choose Overhead Circuits > Repai r IP Circuits [...]

18-5 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F305 Provision Path Trace on Circuit Sourc e and Destination Ports Step 4 Choose the VC circuit you w ant to trace, then click Edit . Step 5 In the Edit Circuit windo w , click the Sho w Detailed Map check box at the bottom of the window . A detailed map o[...]

18-6 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F305 Provision Path T race on Circuit Source and Destina tion Ports Figur e 18-1 Selecting the Edit P ath T race Option b. In the New Expected String f ield, enter the circuit source transmit stri ng. Enter a string th at makes the source port easy to iden[...]

18-7 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F305 Provision Path Trace on Circuit Sourc e and Destination Ports • Auto—The first string recei ved from the source port is automatically prov isioned as the current expect ed string. An alarm is raised wh en a string that di ffers from the baseline i[...]

18-8 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F306 Provision Path Trace on STM-N Ports • Click Default to return to the path trace default settings (P ath T race M ode is set to Of f and the New T ransmit and Ne w Expected Strings are null). Caution Clicking Default will generate alarms if the port [...]

18-9 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F307 Create Login Node Groups • Auto—Uses the first string rece i ved from the port at the ot her path trace end as the current expected string. An alarm is raised when a string that differs from the basel i ne is receiv ed. For STM-N ports, Auto is re[...]

18-10 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F308 Delete a N ode from the Current Session or Login Gr oup Figure 1 8-2 Login Node Group Step 8 Return to your ori ginating procedure (NTP). DLP-F308 Delete a Node from the Current Session or Login Group Step 1 From the V iew menu, choose Go to Netw ork[...]

18-11 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F309 Configure the CTC Alerts Dialog Box for Automatic Popup DLP-F309 Configure the CTC Alerts Dialog Box for Automatic Popup Step 1 Click the CTC Alerts toolbar icon. Step 2 In the CTC Alerts dialog box, choose o ne of the follo wing: • All alerts —S[...]

18-12 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F311 Remove Pa ss-through Connections Step 4 Choose the JRE ve rsion. Step 5 Click OK . Step 6 From the File menu, choose Exit . Step 7 In the conf irmation dialog box, click Ye s . Step 8 Return to your ori ginating procedure (NTP). DLP-F311 Remove Pass-[...]

18-13 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F312 Delete a Node from a Specified Login Node Group DLP-F312 Delete a Node from a Specified Login Node Group Step 1 From the CTC Edit menu, choose Pr eferences . Step 2 In the Preferences dialog box, click the Login Node Groups tab . Step 3 Click the log[...]

18-14 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F314 Provision MS-DCC Terminatio ns • Locked,maintenance —Puts the circuit cross-connects in th e Locked -enabled,m aintenance service state. The maintenance state does not interrupt traf fic flo w; it suppresses al arms and conditions and allows loop[...]

18-15 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F314 Provision MS-DCC Termination s Note When MS- DCC is pr ovisioned, an R S-DCC t erminati on is allowed on the sa me port , but is not recommended. RS-DCC and MS -DCC are only need ed on the same port during a software upgrade if the softw are version [...]

18-16 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F315 Provision a Proxy Tunnel – ISH—Sets the Intermediate System Hello PDU propagation f requency . Intermediate system NEs send ISHs to other ESs and ISs to inform them about the IS NETs it serves. The default is 10 seconds. The range is 10 to 1000 s[...]

18-17 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F316 Provision a Firewall Tunnel Step 4 Click OK . Step 5 Continue with your originating proced ure (NTP). DLP-F316 Provision a Firewall Tunnel Note If the proxy serv er is configured as proxy-o n ly or is disabled, yo u cannot set up a f irewall tunn el.[...]

18-18 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F317 Delete a Prox y Tunnel DLP-F317 Delete a Proxy Tunnel Step 1 Click the Pro visioning > Network > Proxy subtabs. Step 2 Click the proxy tunnel that you w ant to delete. Step 3 Click Delete . Step 4 Return to your ori ginating procedure (NTP). DL[...]

18-19 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F319 Change an RS-DCC Termination DLP-F319 Change an RS-DCC Termination Step 1 Click the Pro visioning > Comm Channels > RS-DCC tabs. Step 2 Click the RS-DCC that you wa nt to change. Step 3 Click Edit . Step 4 In the RS-DCC T ermination Editor dial[...]

18-20 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F321 Delete an RS-DCC Ter mination • Far End i s Foreign—Check this box to specify that the MS-DCC terminat ion is a non-ONS node. • Far end IP—If you checked the Far End is Foreign check box, type the IP address of the f ar-end node or lea ve the[...]

18-21 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F323 Use the Reinitialization Tool to Clear the Database and Upload Software (UNIX) Caution Deleting a DCC termination can cause you to lose visibility of nodes that do not hav e other DCCs or network co nnections to the CTC computer . Step 1 Click the Pr[...]

18-22 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F324 Provision ASAP Ethernet Ports • Password—Enter the password for the user ID. • Upload Package—Check this box to send the software package fi le to the node. If unchecked, the software stored on t he node is not modif ied. • Force Upload—C[...]

18-23 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F325 Provision ASAP POS Ports Step 3 For each port, pro vision the following parameters: • Port Name—If you want t o label the port, type the port name. • Admin State—Choose Unlocked to put the p ort in servic e. • Enable Flow Control— Check t[...]

18-24 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F326 View ASAP STM-N PM Parameters Note An Encapsula tion Mismatch Path (ENC A P-MISMA TC H-P) alarm appears when a point-to-point circui t is created between two Et hernet card ports with incompatible encapsulation payload types. Step 4 Click A pply . St[...]

18-25 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F327 View ASAP Ether P o rts Statistics PM Parameters Figur e 18-3 Viewin g ASAP Card P erfor mance Monit or ing Infor mation Step 3 In the Port drop-do wn list, choose the port that you w ant to monitor . Step 4 Click Refresh . Step 5 V iew the PM parame[...]

18-26 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F327 View ASAP Ether Po rts Statistics PM Parameters Step 1 In node vie w , double-click the card where you w ant to view PM counts. The car d vie w appears. Step 2 Click the Perf ormance > Ethernet > Ether P orts > Statistics tabs ( Figure 18-4 [...]

18-27 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F328 View ASAP Ether Ports Utilization PM Parameters DLP-F328 View ASAP Ether Ports Utilization PM Parameters Step 1 In node vie w , double-click the ASAP card where you w ant to view PM counts. The card view appears. Step 2 Click the Perf ormance > Et[...]

18-28 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F329 View ASAP POS Po rts Statistics PM Parameters Step 6 Return to your ori ginating procedure (NTP). DLP-F329 View ASAP POS Ports Statistics PM Parameters Step 1 In node vie w , double-click the ASAP card where you w ant to view PM counts. The card view[...]

18-29 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F330 View ASAP POS Ports Utilization PM Parameters Note T o refresh, reset, or clear PM counts, see the “NTP-F18 4 Change the PM Display” pro cedure on page 8-2 . Step 5 Return to your ori ginating procedure (NTP). DLP-F330 View ASAP POS Ports Utiliza[...]

18-30 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F331 View ASAP POS Po rts History PM Parameters Step 4 V iew the Port # column f or the port that you want to monit or . Step 5 The Tx and Rx bandwidth utilization v alues for the previous time int erv als appear in the Pre v- n columns. For PM parameter [...]

18-31 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F332 Change Node Acce ss and PM Clearing Privilege Figure 1 8-8 Ether net POS Por ts History in the Card View P erfor mance Win dow Step 3 Click Refresh . Performance monitoring statistics appear for each port on the card. Step 4 V iew the PM parameter na[...]

18-32 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F332 Change Node A c cess and PM Clearing Pr ivilege Step 1 In node vie w , click the Pro visioning > Security > Access ta bs. Step 2 In the Access area, prov ision the follo wing: • LAN access—Choose one of the foll owing options to set the acc[...]

18-33 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F333 Install the ASAP Carrier Modules Step 10 Return to your ori ginating procedure (NTP). DLP-F333 Install the ASAP Carrier Modules War ni n g During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the m[...]

18-34 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F334 Verify Pass-Through C ircuits Step 4 V erify the LED a cti vity on the c ard faceplate: 1. The ST A T , SR V , and LASER ON LEDs turn on for 20 seconds. 2. The ST A T LED blinks and the other LEDs turn on f or 30 to 50 seconds. 3. All LEDs blink once[...]

18-35 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F335 Preprovision an SFP DLP-F335 Preprovision an SFP Note If you preprov i sion a multirate SF P , you must ne xt select the line rate using the “DLP-F390 Provision an Optical Line Rat e and W a velength” task on page 18- 103 . Step 1 Complete the ?[...]

18-36 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F336 Print CTC Data Note Only the parameters that are editabl e for the PPMs on a particular platfo rm type are provisi onable. For example, some platforms may not ha ve PPMs with conf igurable wa velengths or reaches. In this case, wa velength and reach [...]

18-37 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F337 View ASAP Ether Ports History PM Parameters • Maintena nce > Protecti on window • Maintena nce > Diagno stic window • Maintenanc e > Preferred Copy window • Maintenance > T iming > Source windo w The T able Contents op tion pri[...]

18-38 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F338 Create a Two-Fiber MS- SPRing Us ing the MS-SPRing Wizard Figur e 18-1 0 Ether net Ether P orts History on the Car d View P erformance Windo w Step 3 Click Refr esh . Performance monitoring statistics for each port on the card appear . Step 4 V iew t[...]

18-39 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F338 Create a Two-Fiber MS-SPRing Using the MS-SPRing Wizard Step 1 From the V iew menu, choose Go to Netw ork View . Step 2 Click the Pr ovisioning > MS-SPRing tabs. Step 3 Click Create MS-SPRing . Step 4 In the MS-SPRing Creation d ialog box, set the[...]

18-40 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F339 Create a Two- Fiber MS-SPRing Manually • On the network view graphic, a green span line appears b etween all MS-SPRing nodes. • All E-W -MISMA TCH, RING-MISMA TC H, A PSCIMP , APSCDFL TK, and MSSP-OOSYNC alarms are cleared. See the Cisco ONS 1560[...]

18-41 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F340 Change an MS-SPRing Node ID • East Line—Assign the east MS-SPRi ng port for the node from the d rop-do wn list. Step 5 Click OK . Note Some or all of the follo wing alarms will appear until all the MS- SPRing nodes are provisioned: E-W MISMA TCH,[...]

18-42 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F341 MS-SPRing Exercise Ring Test DLP-F341 MS-SPRing Exercise Ring Test Step 1 From the V iew menu, choose Go T o Network V iew . Step 2 Click the Pro visioning > MS-SPRing ta bs. Step 3 Click the ro w of the MS-SPRing you will ex ercise, then click Ed[...]

18-43 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F342 MS-SPRing Switch Test If you do not see an y MS-SPRing ex ercise conditions, click the Filter b utton and verify that f iltering is not turned on. Also, check that al arms and conditions ar e not suppressed for a node or MS-SPRing drop cards. See the[...]

18-44 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F342 MS-SPRing Switch Test Step 5 V erify the conditions: a. Click the Conditions tab . b. Click Retriev e . c. V erify that the follo wing conditions are reported on the n ode where you inv oked the Fo rce Ring switch on the west port: • FORCE-REQ-RING[...]

18-45 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F342 MS-SPRing Switch Test Step 11 Clear the switch on the west port: a. Right-click the west por t of the MS-SPRing node where you in voked the Force Ri ng switch and choose Set W est Protection Operation . b. In the Set W est Protec tion Operation d ial[...]

18-46 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F342 MS-SPRing Switch Test • RING-SW -EAST—A Ring Switch Acti ve on the east side condition is repor ted against the working span on the west side of the node. Step 16 (Optional) If you r e mapped the K3 b yte to run an ONS 15600 SDH MS-SPRing through[...]

18-47 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F343 Provision an STM-N Circuit Route DLP-F343 Provision an STM-N Circuit Route Step 1 In the Circuit Creation wizard in the Route Revie w/Edit area, click the source node icon i f it is not already selected. Step 2 Starting with a span on t he source nod[...]

18-48 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F345 Clear an MS-SPRing Manual Ring Switch Caution T raff ic is not protected during a manual ring protection switch. Step 1 From the V iew menu, choose Go T o Network V iew . Step 2 Click the Pro visioning > MS-SPRing ta bs. Step 3 Choose the MS-SPRin[...]

18-49 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F346 Create an MS-SPRing on a Single Node Ti p T o move an icon to a ne w location, for exampl e, to see MS-SPRing chan nel (port) information more clearly , click an ico n on the Edit MS-SPRing network graphic and while p ressing Ctrl , drag the ic on to[...]

18-50 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F347 Initiate an MS-S PRing Force Ring Switch Note The MS-SPRing is incomplete and alarms are pr esent until the node is connected to other MS-SPRing nodes. Step 5 Return to your ori ginating procedure (NTP). DLP-F347 Initiate an MS-SPRing Force Ring Swit[...]

18-51 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F348 View Circuit Information On the network graphic, an F appears on the working M S-SPRin g channel where you in voked the protection switch. The span lines chan ge c olor to reflect the forced traf f ic. Green span lines indicate the ne w MS-SPRing pat[...]

18-52 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F348 View Circuit Inf ormation Note In node or card view , you can change th e scope of the circuits that are displayed by choosing Card (in card vie w), Node, or Network fr om the Scope drop-do wn list in the bottom right corner of the Circuits window . [...]

18-53 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F348 View Circuit Information T able 18-3 ONS 1560 0 SDH Circuit Status Status Definition/Activity CREA TIN G CTC is creating a circuit. DISCO VERED CTC created a circuit. All components are in place and a complete path exi sts from ci rcuit source to des[...]

18-54 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F349 Install Fibe r-Optic Cables for MS -SPRing Configurations • Source—The circuit source in the format: node/slot/port/STS . If an ASAP PPM po rt is the cir cuit source, the port format is PIM-PPM-port , where PIM and PPM values are 1 through 4 (for[...]

18-55 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F349 Install Fiber-Optic Cabl es for MS-SPRing Configurations Caution Do not pro vision the MS-SPRing east and west ports on th e same STM-N card. Note T o av oid error , connect fiber -optic cab le so that the farthest slot to th e right represents the e[...]

18-56 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F350 Delete an MS-SPRing from a Single Node Step 4 Return to your ori ginating procedure (NTP). DLP-F350 Delete an MS-SPRing from a Single Node Step 1 In node vie w , display the node that w as removed from the MS -SPRing: • If the node that was remove [...]

18-57 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F351 Roll the Source or Destination of One Optical Circuit Step 4 From the T ools menu , choose Circuits > Roll Cir cuit . Step 5 In the Roll Attrib utes area, complete the follo wing ( Figure 18-12 ): a. From the Circui t Roll Mode drop -down list, ch[...]

18-58 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F351 Roll the Source or Destination of One Optical Circuit Figur e 18-13 Selecting a P at h Step 8 Click Next . Step 9 In the Select New End Point area, choose the Slot , Port , and VC3 or VC4 from the drop-do wn lists to select the Roll T o facility ( Fi[...]

18-59 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F351 Roll the Source or Destination of One Optical Circuit Step 11 Click the Rolls tab ( Figure 18-15 ). F or the pending roll, vie w the Roll V alid Signal status. When one of the follo wing conditions are met, continue with Step 12 . • If the Roll V a[...]

18-60 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F352 Roll One Cross-Connec t from an Optical Circuit to a Second Optical Circuit DLP-F352 Roll One Cross-Connect from an Optical Circuit to a Second Optical Circuit Step 1 From the V iew menu, choose Go T o Network V iew . Step 2 Click the Circ uits tab .[...]

18-61 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F352 Roll One Cross-Connect from an Optical Circu it to a Second Optical Circuit Figure 1 8-16 Selecting Roll Attr ibutes for a Single Roll onto a Second Circuit Step 6 Click Next . Step 7 In the Pi vot/Fix ed Point 1 windo w , click the square representi[...]

18-62 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F353 Roll Two Cross-Connects on One Optical Circuit Using Automatic Routing Step 12 If you selected Manual in Step 5 , click the roll on the Rolls ta b and click Complete to route the traf fic to the ne w port. If you selected Au to, continue with Step 13[...]

18-63 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F353 Roll Two Cross-Connects on One Optical Circuit Using Automatic Routing Figur e 18-1 7 Selecting Dual Roll At tr ibutes Step 6 Click Next . Step 7 In the Pi vot/Fix ed Point 1 windo w , click the square re presenting the f ixed path of the first conne[...]

18-64 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F353 Roll Two Cross-Connects on One Optical Circuit Using Automatic Routing Figure 1 8-18 Setting Roll Routing Pr ef er ences Step 13 T o route the circuit ov er a protected path, check Fully Protected Path . (If you do not want to route the circuit on a [...]

18-65 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F353 Roll Two Cross-Connects on One Optical Circuit Using Automatic Routing Step 16 If you check ed Re view Route Before Creation in Step 12 : a. In the Roll Route Re view an d Edit area, revie w the circuit route. T o add or delete a circuit span, select[...]

18-66 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F354 Roll Two Cross-Connects on One Optical Circuit Using Manu al Routing DLP-F354 Roll Two Cross-Connects on One Optical Circuit Using Manual Routing Step 1 From the V iew menu, choose Go T o Network V iew . Step 2 Click the Circui ts tab. Step 3 Click t[...]

18-67 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F354 Roll Two Cross-Connects on One Optical Circuit Using Manual Routing • T o route the circuit on a protected path, leav e Fully Protected Path check ed and continue with Step 14 . • T o create an unprotected circuit, uncheck Fully Protected P ath a[...]

18-68 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F355 Roll Two Cros s-Connects from One Optical Circuit to a Second Optical Circuit DLP-F355 Roll Two Cross-Connects from One Optical Circuit to a Second Optical Circuit Step 1 From the V iew menu, choose Go T o Network V iew . Step 2 Click the Circ uits t[...]

18-69 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F356 Delete a Roll Step 11 Click Next . Step 12 Click Finish . In the Circuits tab, the Roll From and Ro ll T o circuits change from the DISCO VERED status to R OLL RENDING. Step 13 Click the Rolls tab . T wo new rol ls now appear on the Rolls tab . For e[...]

18-70 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F357 Cancel a Roll Step 3 Click the rolled circuit that you w ant to delete. Step 4 From the T ools menu , choose Circuits > Delete Ro lls . Step 5 In the conf irmation dialog box, click Ye s . Step 6 Return to your ori ginating procedure (NTP). DLP-F3[...]

18-71 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F359 Change the Optic al Line Rate Note The ASAP card hosts up to four 4PIO modules. Each 4PIO hosts four SFPs, which pr ovide a fiber interface that must be pro visioned as STM-1, ST M-4, STM-16, or Gigabit Ethernet. SFPs are called pluggable port mo dul[...]

18-72 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F360 Delete a PPM Step 6 Click Ye s in the Confirm Port Rate Change d ialog box. Step 7 Return to your ori ginating procedure (NTP). DLP-F360 Delete a PPM Step 1 Determine if you can delete th e PPM. Y ou cannot de lete a port on a PPM if it is in service[...]

18-73 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F361 Provision OSI Routing Mode Step 7 Return to your ori ginating procedure (NTP). DLP-F361 Provision OSI Routing Mode Caution Do not complete this task unti l you confirm the role of the node within t he network. I t will be ei ther an Intermediated Sys[...]

18-74 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F362 Provision or Modify TARP Operating Parameters • Intermediate System Level 1/Le vel 2 —The ONS 15600 SDH performs IS functions. It communicates with IS and ES nodes th at reside within its OSI area. It also communicates with IS L1/L2 nodes that re[...]

18-75 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F362 Provision or Modify TARP Operating Parameters • T ARP PDUs Origination—If checked (def ault), the node performs all T ARP originati on functions including: – TID to NSAP resolution requests (orig i nate T ARP T ype 1 and T y pe 2 PDUs) – NSAP[...]

18-76 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F363 Add a Static TID -to-NSAP Entry to the TA RP Data Cache • LDB Flush—Sets the frequenc y period for flushing the LDB. The def ault is 5 minutes. The range is 0 to 1440 minutes. • T1—Sets the amount of tim e to wait for a response to a T ype 1 [...]

18-77 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F364 Remove a Static TID-to-NSAP Entry from the TARP Data Cache DLP-F364 Remove a Static TID-to-NSAP Entry from the TARP Data Cache Step 1 In node vie w , click the Pro visioning > OSI > T ARP > Static TDC tabs. Step 2 Click the static entry that[...]

18-78 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F366 Provision OSI Routers Step 5 Return to your ori ginating procedure (NTP). DLP-F366 Provision OSI Routers Note Router 1 must be enabled before you can enable and edit the primary manu al area addresses for Routers 2 through 12. Note The Router 1 manua[...]

18-79 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F367 Provision Additional Manual Area Addresses DLP-F367 Provision Additional Manual Area Addresses Step 1 Click the Pro visioning > OSI > Routers > Setup tabs. Step 2 Chose the router where you w ant provision an additional manual area address a[...]

18-80 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F369 Create an IP-Over-CLNS Tunnel Step 1 Complete the “DLP-F181 Log into CTC” task on pa ge 16-34 at the node who se OSI routers y ou want to provisi on. Step 2 Click the Pro visioning > OSI > Routers > Subnet tabs. Step 3 Click Enable LAN S[...]

18-81 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F370 Remove a TARP Manual Ad jacency Table Entry Step 3 Click Crea te . Step 4 In the Create IP Over OSI T unnel dial og box, complete the follo wing f ields: • T unnel T ype—Choose a tun nel type: – Cisco —Creates the proprietary Ci sco IP tunnel[...]

18-82 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F371 Change the OSI Routing Mode Step 2 Click the MA T entry that you want to delete. Step 3 Click Rem ove . Step 4 In the Delete TDC Entry di alog box, clic k OK . Step 5 Return to your ori ginating procedure (NTP). DLP-F371 Change the OSI Routing Mode C[...]

18-83 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F372 Edit the OSI Router Configuration Note Changing a routing mode shoul d be carefully considered. Additional information about OSI systems and protocols are pro vided in the “Man agement Network Connecti vity” chapter of the Cisco ONS 15600 SDH Ref[...]

18-84 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F373 Edit the OSI Subnetwork Point of Attachment DLP-F373 Edit the OSI Subnetwork Point of Attachment Step 1 In the node vie w , click the Pro v isioning > OSI > Routers > Subnet tabs. Step 2 Choose the subnet you wa nt to edit, then clic k Edit [...]

18-85 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F375 Delete an IP-Over-CLNS Tunnel Caution Changing the IP or NSAP addresses or an IP-o ver- CLNS tunnel can cause loss o f NE visibility or NE isolation. Do not change netw ork addresses until you ver ify the changes with your network administrator . Ste[...]

18-86 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F376 View IS-IS Routing Information Base Caution Deleting an IP-o ver-CLN S tunnel might cause t h e nodes to lose visibilit y or cause node isolation. If node isolation occurs, onsi te provisioning might be required to regain connectivity . Alw ays conf [...]

18-87 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F377 View ES-IS Routing Information Base DLP-F377 View ES-IS Routing Information Base Step 1 In the node vie w , click the Maintenance > OSI > ES-IS RIB tabs. Step 2 V iew the foll owing RIB in formation fo r Router 1: • Subnet T ype—Indicates t[...]

18-88 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F379 Export CTC Data • NSAP/NET—The Network Service Access Poin t or Network Element T itle of the originating NE. • T ype—Indicates ho w the TDC entry was created: – Dynamic —The entry was created through t he T ARP propag ation process. – [...]

18-89 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F379 Export CTC Data Step 3 From the CTC File menu, click Export . Step 4 In the Export dialog box choose a format for t he data ( Figure 18-19 ): • As HTML —Saves the data as an HTML f ile. The file can be view ed with a web bro w ser without running[...]

18-90 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F380 Configure the N ode for RADIUS Authentication • Maintena nce > Database w indow • Maintena nce > Protecti on window • Maintena nce > Diagno stic window • Maintenanc e > Preferred Copy window • Maintenance > T iming > Sourc[...]

18-91 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F380 Configure the Node for RADIUS Authentication 1 for Maintenance User 2 for Prov isioning User 3 for Super User Step 1 In node vie w , click the Pr ovisioning > Se curity > RADIUS Server tabs ( Figu re 18-20 ). Figur e 18-20 RADIUS Serv er T ab S[...]

18-92 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F381 Delete a Server Trail Step 4 Enter the shared secret in th e Shared Secret field. A shared secret is a text string that serves as a password between a RADIU S client and RADIUS server . Step 5 Enter the RADIUS authentication port nu mber in the Authe[...]

18-93 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F382 Grant Superuser Privileges to a Provisioning User Step 6 Return to your ori ginating procedure (NTP). DLP-F382 Grant Superuser Privil eges to a Provisioning User Step 1 In node vie w , click the Pro visioning > Defaults tabs. Step 2 In the Node De[...]

18-94 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F383 Download an Al arm Severity Profile Step 1 T o access the alarm profile editor from network vie w , click the Provisioning > Al arm Profiles tabs Step 2 T o access the prof ile editor from nod e vie w , click the Pr ovisioning > Alarm Prof iles[...]

18-95 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F384 Install the ASAP 1PIO and 4PIO (PIM) Modul es DLP-F384 Install the ASAP 1PIO and 4PIO (PIM) Modules War ni n g During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the midplane wit h your hand or a[...]

18-96 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F384 Install the ASAP 1PIO and 4PIO (PIM) Modules Figur e 18-22 1PIO Module F aceplate Figure 18-23 sho ws the 4PIO module f aceplate. Figur e 18-23 4PIO Module F aceplate Note The LEDs located on the 1PIO and 4PIO will not light until a fix ed rate SFP/X[...]

18-97 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F385 Consolidate Links in Network View Step 5 After you ha ve logged into CTC, verify th at the card appears in the card view . See Chapter 3, “Connect the PC and Log into the GUI” for CTC information and setup instructions. Step 6 Return to your ori [...]

18-98 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F385 Consolidate Links in Network View Note The links consolidate by class. Fo r example, if you select a DCC link for consolidation only the DCC links will consol idate, leaving any other link classes expanded. Figure 18-24 sho ws a network vie w with un[...]

18-99 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F385 Consolidate Links in Network View Figur e 18-26 Netw ork V iew with Local Link Consolidation Step 6 T o vie w information about the consolidated link, mo ve the mouse o ver the lin k (the tooltip displays t he number of links and the link cl ass), or[...]

18-100 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F386 Adjust the Java Virtual Memory Heap Si ze DLP-F386 Adjust the Java Virtual Memory Heap Size Step 1 From the W indo w s task bar , click Start > Settings > Contr ol Panel . The W indows Co ntrol Pa nel appears. Step 2 Double-click System . The [...]

18-101 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F388 Remove an SFP/XFP Step 2 If you are installing an SFP , orient the SFP so that th e Cisco serial number label is facing aw ay from the shelf (to th e right). If yo u are installi ng an XFP , orient the XFP to the left. Step 3 Unlatch the bail clasp [...]

18-102 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F389 Remove a 1PIO or 4PIO (PIM) Modul e DLP-F389 Remove a 1PIO or 4PIO (PIM) Module War ni ng During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the midplane wit h your hand or any metal tool, or yo[...]

18-103 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F390 Provision an Optical Line Rate and Wavelength DLP-F390 Provision an Optical Line Rate and Wavelength Step 1 In node vie w , double-click the ASAP card where you want to provision the lin e rate. Step 2 Click the Pro visioning > Pluggable Port Mod[...]

18-104 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F391 Install Alarm Wires on the CAP/CAP2 Step 12 Return to your ori ginating procedure (NTP). DLP-F391 Install Alarm Wires on the CAP/CAP2 Step 1 Wrap the alarm wires on the appropriate wire-w rap pins according to local site practice . Figure 18-27 sho [...]

18-105 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F391 Install Alarm Wires on the CAP/CAP2 Figur e 18-27 Rear of the ONS 1560 0 SDH, Including the CAP/CAP2 Figure 18-28 sho ws the CAP/CAP2 facep late in detail. 78398[...]

18-106 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F391 Install Alarm Wires on the CAP/CAP2 Figur e 18-28 CAP/CAP2 F ace plate and Connections Figure 18-29 sho ws alarm pin assignments. 78485 Wire wrap pins LAN RJ-45 Craft DB-9 A udible Alarm DB-15 BITS OUT BNC BITS OUT BNC LAN RJ-45 Craft DB-9 BITS IN B[...]

18-107 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F392 Change Line Transmi ssion Settings for STM-N Cards Figur e 18-29 Alar m Pin Assignments on the CAP/CAP2 See Chapter 9, “M anage Alarms ” for instructions about assigning alarms to these pins. Lace or tie wrap cables to the ti e wrap features tha[...]

18-108 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F392 Change Line Transmi ssion Settings for STM-N Cards Step 1 On the shelf gr aphic, double-click the STM- N card th at yo u want to provisi on. The card view appear s. Step 2 For STM-16 or STM-64 card s, click the Provisioning > Line tabs. For the A[...]

18-109 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F392 Change Line Transmi ssion Settings for STM-N Cards Admin State Sets the port service state unless network conditio ns pre vent the change. • Unlocked—Puts the port in service. The port service state changes to Unlocked-enabled. • Unlocked,auto[...]

18-110 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F392 Change Line Transmi ssion Settings for STM-N Cards Service State Identif ies the autonomously generated state that gi ves the overall condition of the port. Servic e states app ear in the format: Primary State-Primary State Qualifier , Secondary Sta[...]

18-111 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F393 Change Threshold Se ttings for STM-N Ports Step 4 Click Apply . Step 5 Return to your ori ginating procedure (NTP). DLP-F393 Change Threshold Settings for STM-N Ports Note For the default values and domains of use r-provisionable card settings, refe[...]

18-112 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F393 Change Threshold Settings for STM-N Ports Step 1 On the shelf graphi c, double-click the STM-16, STM-64, o r ASAP card that you want to pro vision. The card vie w appears. Step 2 As needed, c omplete th e following: a. Click Line , Section , Path, o[...]

18-113 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F394 Change Optics Thresh old Settings for STM-N Ports Step 3 Click Apply . Step 4 Return to your ori ginating procedure (NTP). DLP-F394 Change Optics Threshold Settings for STM-N Ports Note For the default values and domains of use r-provisionable card [...]

18-114 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F394 Change Optics Thresh old Setti ngs for STM-N Ports c. Select a 15 Min or 1 Day performan ce monitoring interv al radio b utton (a vailable for TCA only), and then click Refre sh . d. Click Refresh to view or modify the th resholds for each selection[...]

18-115 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F395 Change the STM-N Port ALS Maintenance Settings DLP-F395 Change the STM-N Port ALS Maintenance Settings Note For the default values and domains o f user-provision able card settings, refer to the “Network Element Defaul ts” appendix in the Cisco [...]

18-116 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F396 Clear All PM Thr esholds Step 5 Return to your ori ginating procedure (NTP). DLP-F396 Clear All PM Thresholds Caution Pressing the Reset b utton can mask problems if used incorrectl y . This button is comm only used for testing purposes. Step 1 In n[...]

18-117 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F397 Provision the Designated SOCKS Servers Step 4 Click Ye s in the Reset to default di alog box. Step 5 V erify that the PM thresholds have been reset. Step 6 Return to your ori ginating procedure (NTP). DLP-F397 Provision the Designated SOCKS Servers [...]

18-118 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F398 Install the CT C Launcher Applic ation from a Release 8.0 So ftware CD Step 4 Click Add . The node is added to the SOCKS serv er list. If you need to remove a node on the li st, click Rem ove . Step 5 Repeat Steps 3 and 4 to add all qualif ied ONS 1[...]

18-119 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F399 Install the CTC Launcher Application from a Release 8.0 Node Step 1 Using a web bro wser, go to the follo wing address, where node name is the DNS name of a node you are going to access: http:// <node-name> /fs/StartCTC.exe The bro wser File D[...]

18-120 Cisco ONS 15600 SDH Procedure Guide, R8.0 October 2007 Chapter 18 DLPs F300 to F399 DLP- F399 Install the CT C Launcher Applic ation from a Release 8.0 No de[...]