Cisco Systems WS-C6513-E-RF manual

Americas Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note Produc t Number: WS- SVC-CMM Last Updated: March 23, 2009 This publication co ntains the procedures for inst alling and conf i[...]

Contents 2 Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Ro uter Installation and Verification Not e Contents This publication contains these sections: • Front Panel Description s, page 2 • Requirements, page 6 • Safety Overvie w , page 7 • Required T o ols, page 10 • Installing and Remo ving the M[...]

Front Panel De scriptions 3 Cisco Communication Media Module for Catalyst 6500 Series Swit ch and Cisco 7600 Series Router In stallation and Verification Not e Note For information o n the supervisor engine LEDs, see the Catalyst 6500 Series Switc h Supervisor Engine Guide at this URL: http://www .cisco.com/en/ US/docs/switches/lan/catalyst6 500/ha[...]

Front Panel Descriptions 4 Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Ro uter Installation and Verification Not e 6-Port T1 and E1 Port Adapters The front panel features of th e 6-port T1 and E1 port adapters are as follo ws: • Receiv e port LEDs—The LEDs on the front pane l indicate the status of eac[...]

Front Panel De scriptions 5 Cisco Communication Media Module for Catalyst 6500 Series Swit ch and Cisco 7600 Series Router In stallation and Verification Not e Figure 2 6-P ort T1 and E1 Port A dapter Front P anel Featur es 24-Port FXS Port Adapter The front panel features of the 2 4-p ort FXS port adapter are as fo llows: • Receiv e port LEDs—[...]

Requirements 6 Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Ro uter Installation and Verification Not e Figur e 3 24-Po rt FXS P o rt A dapter Fr ont P anel Feat ures Ad-Hoc Conferencing and Transcoding Port Adapter The front panel features of the ad-hoc conferen cing and tran scoding port adapter are sho w[...]

Safety Overview 7 Cisco Communication Media Module for Catalyst 6500 Series Swit ch and Cisco 7600 Series Router In stallation and Verification Not e Hardware Requirements The hardware requirements fo r the modules are as follows: • Catalyst 6500 series switch. • Cisco 7600 series rout er . • 252.0 W atts (6.00 A @ 42 V) of a vailable system [...]

Safety Overview 8 Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Ro uter Installation and Verification Not e War ni n g Ultimate disposal of this product should be han dled according to all national laws and regu lations. Statement 1040 War ni n g Only trained and qualified pe rsonnel should be allowed to ins[...]

Safety Overview 9 Cisco Communication Media Module for Catalyst 6500 Series Swit ch and Cisco 7600 Series Router In stallation and Verification Not e War ni n g Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. Statement 1037 War ni n g Hazardous network voltages are prese[...]

Required Tools 10 Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Ro uter Installation and Verification Not e Required Tools War ni n g Only trained and qualified pe rsonnel should be allowed to install, replace, or service this equipment. Statement 1030 These tools are required to remov e and replace the modu[...]

Installing and Re moving the Module 11 Cisco Communication Media Module for Catalyst 6500 Series Swit ch and Cisco 7600 Series Router In stallation and Verification Not e Step 3 V erify that there is enough clea rance to accommodate any interfac e equipment that you will connect directly to the m odule ports. If p ossible, plac e modules be tween e[...]

Installing and Removing the Module 12 Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Ro uter Installation and Verification Not e Figur e 5 P ositioning the Module in a Hor izontal Slot Chassis 58569 INPUT OK FAN OK OUTPUT FAI L o INPUT OK FAN OK OUTPUT FAI L o 1 2 3 FAN STA TUS 4 5 6 S U P E R V IS O R 2 W S [...]

Installing and Re moving the Module 13 Cisco Communication Media Module for Catalyst 6500 Series Swit ch and Cisco 7600 Series Router In stallation and Verification Not e Figur e 6 Clear ing the EMI Gask et in a Hor izontal Sl ot Chassis b. Using the thumb and foref inger of each hand, grasp the tw o ejector levers and press do wn to c reate a smal[...]

Installing and Removing the Module 14 Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Ro uter Installation and Verification Not e Figure 7 Ejector Lev er Cl osur e in a Hor izontal Slot Chassis Note Failure t o fully seat the module in the back plane connector can resu lt in error messages. d. T ighten the two[...]

Installing and Re moving the Module 15 Cisco Communication Media Module for Catalyst 6500 Series Swit ch and Cisco 7600 Series Router In stallation and Verification Not e Figur e 8 P ositioning the Module in a V ertical Slot Chassis b. Carefully slide the modul e into the slot until the EMI gasket alo n g the right edge of t he module makes contact[...]

Installing and Removing the Module 16 Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Ro uter Installation and Verification Not e Figure 9 Clearing the EMI Gasket in a V ertical Slot Chassis Caution Exerting t oo much pressure on the ejector le vers will bend and damage them. d. While pressing on t h e ejector[...]

Installing and Re moving the Module 17 Cisco Communication Media Module for Catalyst 6500 Series Swit ch and Cisco 7600 Series Router In stallation and Verification Not e Figur e 1 0 Ejector Lev er Closure in a V ertical Slot Chassis e. T ighten the two capti ve installation scre ws on the module. Note Make sure that the ejector lev ers are fully c[...]

Installing and Removing the Module 18 Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Ro uter Installation and Verification Not e T o remov e a module from the chassis, perform these steps: Step 1 Disconnect any network interface cables that are attached to the m odule. Step 2 V erify that the capti ve install[...]

Removing and Rep lacing Port Adapte rs 19 Cisco Communication Media Module for Catalyst 6500 Series Swit ch and Cisco 7600 Series Router In stallation and Verification Not e Removing and Replacing Port Adapters Follo w the procedures in this section to remov e and replace the port adapters on the CMM: • Removing a Port Adapter from Module Slots 1[...]

Removing and Replacing Port A dapters 20 Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Ro uter Installation and Verification Not e War ni n g Blank faceplates and c over panels serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they co ntain electrom[...]

Removing and Rep lacing Port Adapte rs 21 Cisco Communication Media Module for Catalyst 6500 Series Swit ch and Cisco 7600 Series Router In stallation and Verification Not e Figur e 12 Module (T op View wi th P ort Adapters Installed) Figur e 13 Module (T op View wi th P ort A dapters Removed) 68453 AVVID Services Module STA TUS WS-X6600 Standoffs [...]

Removing and Replacing Port A dapters 22 Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Ro uter Installation and Verification Not e Installing a Port Adapter in Module Slots 1 through 3 Note When you face the module front panel, slot 1 is on th e left, slot 2 is in the midd le, and slot 3 is on the right. Slo[...]

Removing and Rep lacing Port Adapte rs 23 Cisco Communication Media Module for Catalyst 6500 Series Swit ch and Cisco 7600 Series Router In stallation and Verification Not e Caution Using the screws or standoff s to seat the port adapter could warp the port adapter . Befor e you install and tighten the securing screws, ensure that the port adapter [...]

Removing and Replacing Port A dapters 24 Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Ro uter Installation and Verification Not e Step 4 In Figure 13 , note the location of the t wo slot 4 standoff mounting posts. Remo ve the two mounti ng posts that secure the port adapter . Step 5 In Figure 13 , note the [...]

Verifying the Installation 25 Cisco Communication Media Module for Catalyst 6500 Series Swit ch and Cisco 7600 Series Router In stallation and Verification Not e Caution Using the screws or standoff s to seat the port adapter could warp the port adapter . Befor e you install and tighten the securing screws, ensure that the port adapter is fully sea[...]

RJ-45 Port Connector and Cabling Specifications 26 Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Ro uter Installation and Verification Not e War ni n g Hazardous network voltages are present in W AN ports regardless of whether power to the unit is OFF or ON. T o avoid electric shock, use caution when working[...]

RJ-21 Port Connector and Cablin g Specifications 27 Cisco Communication Media Module for Catalyst 6500 Series Swit ch and Cisco 7600 Series Router In stallation and Verification Not e RJ-21 Port Connector and Cabling Specifications Caution Do not connect the WS-SVC-CMM-24FXS port adapter di rectly to a voi cemail server , IVR application, or fax se[...]

Accessing the Port Adapter Ports 28 Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Ro uter Installation and Verification Not e Accessing the Port Adapter Ports From the module command- line interface (CLI), you identify each p o rt adapter b y int erface_name follo wed by slot_num / port_num . For ex ample, t[...]

Configuring the Port Adapter Ports 29 Cisco Communication Media Module for Catalyst 6500 Series Swit ch and Cisco 7600 Series Router In stallation and Verification Not e Configuring the Port Adapter Ports Config uring the module interfaces is similar to conf iguring the voice int e rfaces on other Cisco produ cts. module interf ace configuration re[...]

Disaster Recovery for Module So ftware Upgrades 30 Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Ro uter Installation and Verification Not e Disaster Recovery for Module Software Upgrades This section describes ho w to recov er in the ev ent that the CMM software image fails to load properly . If there is a [...]

Disaster Recove ry for Module So ftware Upgrades 31 Cisco Communication Media Module for Catalyst 6500 Series Swit ch and Cisco 7600 Series Router In stallation and Verification Not e Disaster Recovery for Supervisor Engines Running Catalyst Operating System Software T o perform disaster recovery on systems that us e the Catalyst operati ng system [...]

Password Recovery 32 Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Ro uter Installation and Verification Not e Step 3 Under the CLI Config mode, enter the tf tp-server [ device ]:[ golden-i mage ] alias [ alias-name ] command to translate the filename of the do wnloaded file. The [ gol den -i mage ] is the f[...]

Regulatory Standards Comp liance 33 Cisco Communication Media Module for Catalyst 6500 Series Swit ch and Cisco 7600 Series Router In stallation and Verification Not e Regulatory Standards Compliance Catalyst 6500 series switches and modules comp ly w ith the regulatory standards that are listed in the Re gulatory Compliance and Safet y Information[...]

Obtaining Docume ntation, Obtain ing Support, and Se curity Guidelines 34 Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Ro uter Installation and Verification Not e This document is to be used in conjunction with th e documents listed in the “Related Documentation” section. Cisco and the Cisco logo are tr[...]