Craftsman 132.24607 manual

Operator's Manual RIDER COOLING SYSTEM Model No. 132.24607 CAUTION: Before using this product, read this manual and follow all Safety Rules and Operating Instructions. IMPORTANT: For replacement parts or assembly questions call 800-320-MIST. • Safety • Assembly • Operation • Maintenance • Troubleshooting Sears, Roebuck and Co., Hoffm[...]

SAFETY RULES .................................... 2 HARDWARE CONTENTS ..................... 3 CARTON CONTENTS ............................ 4 ASSEMBLY .......................................... 5 OPERATION ........................................ 14 MAINTENANCE ................................. 16 STORAGE .................................... 17 TROU[...]

A ...... iii!iii iii_jiiiii ii_iiHiiiTi ¸ii -¸ ? B f ii // H S D E REF. QTY. DESCRIPTION A 2 Hex Bolt, 5/16"-18 x1-1/4" B 2 Flat Washer, 7/8" OD C 4 Cap Screw, 5t16-!8" x 3/4" D 8 Flat Washer, 5/8" OD E 4 Nylock Nut, 5/16"-18 F 2 Dash Adapter Nuts G 4 Routing Clips H 1 Rubber Washer I 1 Dash Adapter Spacer J 4 C[...]

AA. Power Unit BB. Misting Nozzle Assembly CC. Mounting Bracket DD. 9/16" Drill Bit BB /[...]

Tools Required ½" Socket Wrench w/Extension Allen Wrenches Power Drill Adjustable Wrench Mounting Power Unit To Tractor NOTE: If there is a 2 or 3 bin bagger installed on your tractor, you will need to remove the bagger from the tractor before proceeding. Leave the bagger bracket mounted to the vehi- cle. After cooling system is installed, ba[...]

Once all bolts have been installed, tighten all nuts using allen wrench and socket on both bolts and nuts, Mounting Misting Nozzle Assembly to Tractor The rider cooling system misting assembly is designed to be installed on the tractor's dash. Some tractors come equipped with rider cooling system mounting locations. If you do not have a dash w[...]

Using supplied 9/16" drill bit (DD), drill hole through the dash at the bottom of the mounting location. Use caution not to damage anything in the engine com- partment while drilling hole. Step 2 • Install rubber washer (H) onto the misting arm assembly (BB), by sliding over hoses and threaded section until seated against mounting flange. ?[...]

Step 3 IMPORTANT: If you have not already done so, you must disconnect the negative (-) termi- nal of the battery before completing the next steps. • Repeat with the remaining dash adapter nut (F) until seated on bottom surface of the nut already installed. Use care to ONLY tighten second nut. Tighten using moderate force, Do not over tighten, ?[...]

Connecting Power Unit to Misting Arm Assembly Step 1 • Locate supply lines and power connector at the power unit (AA) and uncoil to full length. Step 2 • When the supply lines have exited the underside of the tractor body, feed the supply lines and power connector along tractor chassis into engine compartment. WARNING: Engine components may be [...]

Step 3 • Locate BLACK supply tube from power unit and BLACK supply tube from misting nozzle assembly. • Remove protective caps from the BLACK supply tube and filter attached to the BLACK tube. • Connect BLACK supply tube from misting arm assembly to the filter installed on the BLACK supply tube from the power unit. Continue to push supply tub[...]

Step 3 • Connect power unit's female connector to Maintenance Minder. Step 4 • From inside the engine compartment, locate tractor power supply connector. NOTE: The tractor power supply connector will resemble the female connector supplied with the power unit. It will have blue and black wires attached to it. • Connect power unit male con[...]

Finalizing System Installation Step 1 • Review the illustration below to familiarize yourself with the suggested locations of the routing clips (G) EACH SIDE OF DASH SUPPORT IMPORTANT: Do not kink hoses exiting the power unit. Leave enough excess for a generous bend in the supply lines when assembling clip to tractor, FRAME IN WHEEL WELL Install [...]

Step 2 • Using a supplied cable tie (J) organize any excess length of supply tubes and stow behind battery (or along fuel tank if equipped). Secure supply tubes to electrical supply lines of tractor at convenient locations to prevent line damage during tractor operation. • Using remaining cable ties (J) secure supply tubes to tractor frame alon[...]

KNOW YOUR RIDER COOLING SYSTEM Read this owner's manual before operating. Compare the illustration below with your rider cooling system to familiarize yourself with the various features and their locations. POWER SWITCH Controls the power to the system's pump. FILL CAP Used to seal the water tank. Removal permits the filling of the water [...]

HOW TO START YOUR RIDER COOLING SYSTEM • With the tractor key in "ON" position, toggle power switch on unit to "ON" posi- tion. NOTE: It is normal to experience a delay from the time the system is turned on to the deliv- ery of mist from the nozzle. If this exceeds 2 minutes, refer to the troubleshooting section. HOW TO STOP Y[...]

CUSTOMER RESPONSIBILITIES VIA1 NTENANCE SCHEDULE sill in dates as you complete "egular service Sh eck for loose fasten ers Slean Exterior Zmpty Water Tank Clean Basket Filter Sor_dition Water Tank :_eplace Ah-fWater Filters Read and follow the maintenance schedule and the maintenance procedures listed in this section. %¢" _'_ Servic[...]

• Empty water tank completely, replace cap, and run system to evacuate all wa- ter in supply lines. • Store misting nozzle assembly by folding over dash of tractor. • Ensure the power switch on the power unit is in the "OFF" position. • Clean debris from venting on rear of power unit. • Clean the power unit thoroughly with mild [...]

NOTES: ]8[...]

NOTES: ]9[...]

For expert troubleshooting and home solutions advice: manage home www,managemyhome,com For repair- in your home - of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! uuuuuuu_ i iiiiiiiiiiiiiiii iiiiiiiiiiiiiiii i'i'i'i'i'i'i'i&apos[...]