Craftsman 315.27127 manual

Owner's Manual iPR 0 FES S I 0 HAL i 112 in. PROFESSIONAL CORDLESS HAMMER DRILL Variable Speed / Reversible Model No. 315.271270 Save this manual for future reference _, CAUTION: Read and follow all Safety Rules and Operating Instructions before first use of this product. Customer Help Line: 1-800-932-3188 Sears, Roebuck and Co., Hoffman Estat[...]

TABLE OF CONTENTS • General Safety Rules ................................................................................................................................................. 2-3 • Specific Safety Rules/Symbols ...........................................................................................................................[...]

Tool Use and Care • • Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control. • Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which&apo[...]

Important Safety Instructions For Charger • Save these instructions. This manual contains important safety and operating instructions for battery charger part number 9-11040, Following this rule will reduce the risk of electric shock, fire, or serious personal injury. • Before using battery charger, read all instructions - and cautionary markin[...]

SYMBOLS SYMBOL NAME DESIGNATION/EXPLANATION V Volts Voltage A Amperes Current Hz Hertz Frequency (cycles per second) min Minutes Time Alternating Current Type or a charact'eristic of current --=- Direct Current Type or a characteristic of current no No Load Speed Rotational speed, at no load .../min Revolutions or Reciprocation Per Minute Revo[...]

KNOW YOUR HAMMER DRILL See Figure 1. Before attempting to use your hammer drill, familiarize yourself with all operating features and safety requirements. ,_ WARNING: Carefully read through this entire owner's manual before using your new hammer drill. Pay close • attention to the Rules For Safe Operation, Warnings and Cautions. If you use y[...]

AUXILIARY HANDLE WiNG SCREW TWO SPEED GEAR TRAIN (HI-LO) LEVEL DEPTH GAGE ROD BIT STORAGE AREA KEYLESS CHUCK MODE SELECTOR • TORQUE TRIGGER ADJUSTMENT RING DIRECTION OF ROTATION SELECTOR (FORWARD/REVERSE) BATTERY PACK WRIST STRAP Fig.1 7[...]

LED FUNCTION OF CHARGER YELLOW LIGHT "ON" AND RED LIGHTFLASHING INDICATES DEFECTIVE BATTERY PACK CHARGER FAST CHARGING MODE GREEN LIGHT "ON" INDICATES FULLY CHARGED AND SLOWCHARGING TO MAINTAIN BATTERY PACK CHARGER BATTERY PACK SHOWN IN CHARGER Fig,2 CHARGER See Figure 3, Your charger has a "key hole" hanging feature[...]

AUXILIARY HANDLE See Figure 4. An auxiliary handle is packed with your drill for ease of operation and to help prevent loss of control. The handle can be rotated 360 ° and it can also be mounted on opposite side for left hand use. Note: For convenience and ease of starting threads, the hex nut has been trapped inside the mblded slot in the auxilia[...]

INSTALLING BITS See Figure 7. • Lock the switch trigger by placing the direction of rotation selector in center position. See Figure 13. • Open or close chuck jaws to a point where the open- ing is slightly larger than the bit size you intend to use. Also, raise the front of your drill slightly to keep the bit from f;_lling out of the chuck jaw[...]

_, WARNING: Always wearsafety goggles or safety glasses with side shields when operating tools. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury. CHARGING BATTERY PACK The battery pack for this tool hasbeen shipped in a low charge condition to prevent possible problems. Therefore, you should[...]

SWITCH See Figure 11. To turn your drill ON, depress the switch trigger. To turn it OFF, release the switch trigger. FORWAR_REVERSE SELECTOR CENTER POSITION (LOCK) TRIGGER Fig, 11 VARIABLE SPEED This tool has a variable speed switch that delivers higher speed and torque with increased trigger pressure, Speed is controlled by the amount of switch tr[...]

KEYLESS CHUCK See Figure 14. A keyless chuck has been provided with your drill to allow for easy installation and removal of bits. As the name implies, you can hand tighten or release drill bits in the chuck jaws. Arrows on the chuck indicate which direction to rotate the chuck sleeve in order to LOCK (tighten) or UNLOCK (release) the chuck jaws. L[...]

APPLICATIONS (Use only for the purposes listed below) • Hammer drilling in concrete and masonry. • Drilling in wood. • Drilling in ceramics, plastics, fiberglass, and lami- nates. • Drilling in both hard and soft metals. • Using driving accessories, such as driving screws with screwdriver bits. LEVEL DRILLING See Figure 17. A convenient f[...]

TO ADJUST DRILLING OR HAMMER MODE See Figure 19. • To adjust drill to drilling or hammer operation, rotate mode selector in the direction of arrows as shown in Figure 19. • For your convenience a hammer symbol and drill bit symbol have been molded into the selector. _ WARNING: Your hammer drill has not been designed for reverse hammering. Rever[...]

CHUCK REMOVAL See Figures 20, 21, and22. The chuck must be removed in order to use some accessories. To remove: • Lock the switch trigger by placing the direction of rotation selector in center position. See Figure 13. • Insert a 5/16 inch or larger hex key wrench into the chuck of yo_Jr drill and tighten the chuck jaws securely. • Tap the wr[...]

,_ WARNING: When servicing use only identical Craftsman replacement parts. Use of any other parts may create a hazard or cause product damage. Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, carbon du[...]

The following recommended accessories arecurrently available at Sears Retail Stores. • 6-Pc. Extra Length Magnite Power Bit Set • 30-Pc. Power Screwdriver/Nutdriver Set andCase • 17-Pc. Power Screwdriver/Nutdriver SetandCase • High Speed Bits ...... 1/2 in. Max. • Wood Boring Bits ...... 1-1/4 in. Max. • Masonry Bits ...... 1/2 in. Max.[...]

t CRAFTSMAN 1/2 in. PROFESSIONAL CORDLESS HAMMER DRILL MODEL NO, 315.271270 The model number will be found on a plate attached to the motor housing. Always mention the model number in all correspondence regarding your CRAFTSMAN 1/2 in. PROFESSIONAL CORDLESS HAMMER DRILL or when ordering repair parts. SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS I [...]

In U.S.A. or Canada for in-home major brand repair service: Call 24 hours a day, 7 days a week 1-800-4-MY-HOME s_ (1-800-469-4663) Para pedir servicio de reparacibn a domicilio - 1-800-676-5811 Au Canada pour tout le service ou les pieces - 1-800-469 4663 For the repair or replacement parts you need: Call 6 a.m. - 11 p.m. CST, 7 days a week Parts D[...]