Crimestopper Security Products CS-2004DC manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24

Ir para a página of

Bom manual de uso

As regras impõem ao revendedor a obrigação de fornecer ao comprador o manual com o produto Crimestopper Security Products CS-2004DC. A falta de manual ou informações incorretas fornecidas ao consumidor são a base de uma queixa por não conformidade do produto com o contrato. De acordo com a lei, pode anexar o manual em uma outra forma de que em papel, o que é frequentemente utilizado, anexando uma forma gráfica ou manual electrónicoCrimestopper Security Products CS-2004DC vídeos instrutivos para os usuários. A condição é uma forma legível e compreensível.

O que é a instrução?

A palavra vem do latim "Instructio" ou instruir. Portanto, no manual Crimestopper Security Products CS-2004DC você pode encontrar uma descrição das fases do processo. O objetivo do manual é instruir, facilitar o arranque, a utilização do equipamento ou a execução de determinadas tarefas. O manual é uma coleção de informações sobre o objeto / serviço, um guia.

Infelizmente, pequenos usuários tomam o tempo para ler o manual Crimestopper Security Products CS-2004DC, e um bom manual não só permite conhecer uma série de funcionalidades adicionais do dispositivo, mas evita a formação da maioria das falhas.

Então, o que deve conter o manual perfeito?

Primeiro, o manual Crimestopper Security Products CS-2004DC deve conte:
- dados técnicos do dispositivo Crimestopper Security Products CS-2004DC
- nome do fabricante e ano de fabricação do dispositivo Crimestopper Security Products CS-2004DC
- instruções de utilização, regulação e manutenção do dispositivo Crimestopper Security Products CS-2004DC
- sinais de segurança e certificados que comprovam a conformidade com as normas pertinentes

Por que você não ler manuais?

Normalmente, isso é devido à falta de tempo e à certeza quanto à funcionalidade específica do dispositivo adquirido. Infelizmente, a mesma ligação e o arranque Crimestopper Security Products CS-2004DC não são suficientes. O manual contém uma série de orientações sobre funcionalidades específicas, a segurança, os métodos de manutenção (mesmo sobre produtos que devem ser usados), possíveis defeitos Crimestopper Security Products CS-2004DC e formas de resolver problemas comuns durante o uso. No final, no manual podemos encontrar as coordenadas do serviço Crimestopper Security Products na ausência da eficácia das soluções propostas. Atualmente, muito apreciados são manuais na forma de animações interessantes e vídeos de instrução que de uma forma melhor do que o o folheto falam ao usuário. Este tipo de manual é a chance que o usuário percorrer todo o vídeo instrutivo, sem ignorar especificações e descrições técnicas complicadas Crimestopper Security Products CS-2004DC, como para a versão papel.

Por que ler manuais?

Primeiro de tudo, contem a resposta sobre a construção, as possibilidades do dispositivo Crimestopper Security Products CS-2004DC, uso dos acessórios individuais e uma gama de informações para desfrutar plenamente todos os recursos e facilidades.

Após a compra bem sucedida de um equipamento / dispositivo, é bom ter um momento para se familiarizar com cada parte do manual Crimestopper Security Products CS-2004DC. Atualmente, são cuidadosamente preparados e traduzidos para sejam não só compreensíveis para os usuários, mas para cumprir a sua função básica de informação

Índice do manual

  • Página 1

    SERIES II CS-2004TW1 with 2-Way AM Pager/Remote & 1-Way ‘Sidekick’ Remote CS-2004DC II with two 1-Way Remotes INSTALLATION & OPERATING INSTRUCTIONS CONGRATULATIONS on your choice of a Security System by Crim estopper Security Products Inc. This booklet contains the information necessary fo r installing, using, and maintaining yo ur 2004[...]

  • Página 2

    TABLE OF CONTENTS Installation Cautions & Warn ings…….…………………………………… ………………………...………………2 Suggested Component Mounti ng………….…………………………………………………………….…………..3 Wiring……..…………………………………… ………?[...]

  • Página 3

    CONTROL MODULE / COMPONENT MOUNTING DO NOT Mount the control unit or wiring harness in t he engine compartment or anywhere they can become entangled with moving parts su ch as brake/gas/clutch pedals, or the steering column. The alarm control module should be mounted in a concealed location. The antenna wi re should be routed away from any metal if[...]

  • Página 4

    WIRING BLUE WIRE: (-) HOOD/TRUNK TRIGGER The Blue wire is used for a grounding hood pin switch, trunk pin or both. Connect to existing hood and trunk pin switches that read ground when open. If no existing switc hes are available, install ne w pin switches if desired. GREEN WIRE: (-) DOOR TRIGGER Connect to Negative type door switch es that read gr[...]

  • Página 5

    WIRING BLACK/WHITE WIRE: (+/-) OUTPUT FROM ON-BOARD 15A RELAY (Term #30, Step #3) Connect this wire to your Auxiliary devi ce or Function. The function of this output depends on the connection of the Gray wire and the polarity of this output ma tches the White/Red wire. (See diagram below) Orange/Black Brown/ Black Red/Black (-) Neg. Domelight Illu[...]

  • Página 6

    WIRING MINI PLUGS: 2-PIN PLUG (SMALL): LED INDI CATOR (RED FLASHING LIGHT) 2-PIN PLUG (LARGE): PROGRAM /OVERRID E PUSH BUTTON TIP: The Sensor supplied with this system does not require any additional wiring, simply mount the sensor in a suitable location, plug in, and adjust to the desired levels of sensitivity. The Black dial is for Pre-warn level[...]

  • Página 7

    WIRING BROWN/BLACK WIRE: (-) AUX. OUTP UT #1 OR M.A.P.-Mobile Accessories Protection (Optional) This is a programmable output wire that can operate two different ways: 1. 2. (DEFAULT Operation) A Remote Auxiliary Output that provides a ½ Second (-) Negative pulse when Button #3 is pressed and released to open a pow er trunk or hatch release. Conne[...]

  • Página 8

    POWER DOOR LOCK WIRING 6-PIN DOOR LOCK PLUG 18 GA. (Optional / ON-Board Relays): VIOLET: DOOR LOCK Relay Term. #87: Normally Open [Polarity Input for Lock relay] WHITE: DOOR LOCK Relay Term. #30: Common [Lock Output] GRAY: DOOR LOCK Re lay Term. #87A: Normally Closed VIO/WHT: DOOR UNLOCK Relay Term. #87: Normally Open [Polarity Input for Unlock rel[...]

  • Página 9

    POWER DOOR LOCK DIAGRAMS UL REVERSE P OLA RITY DOOR LOCK WIRING + L NEGA TIVE TRIGG ER D OORLOCK WIRING UL L NOT USED UNLO CK WI RE CUT LOCK W IRE CUT FAC T O RY LOCKING RELA YS UL L + A FTERMA RKET MOT OR DOOR LOCK WI RI NG UL L POS ITI VE TRI GGER DOO RLOCK WI RING FUSED +12V + UNLOCK W IRE LOCK W IRE FAC T O RY LOCKING RELA YS X = BLUE GREEN GRA[...]

  • Página 10

    STARTER DISABLE WIRING STARTER DISABLE PLUG: (3) ORANGE 14 GA. WIRES: (PROGRAMMABLE: Normally Clo sed or Normally Open Config uration with ON-Board Relay) Note: READ BELOW before connect in g starter disable! Normally OPEN must be programmed to operat e. See pg 13. Normally Closed Starter disable is the standard type used with most alarm systems to[...]

  • Página 11

    SYSTEM WIRING DIAGRAM IGNITION ST A RTER SWITCH PA R K I N G LIGHTS (+/-) On -Board Relay BA TTER Y - BLACK/WHITE 15A O n- bo ard WHITE/RED GRA Y CUT IGNITION + SWITCH + CAR-JACK ENABLE OUTPUT (-)HOOD/T RUNK TRIGGER S WITCH SIREN (-) ARMED (-)DOOR T RIGGER SW ITCH + DOOR T RIGGER PIN K VIOLET FUSE POLA RITY SELECT UNLOCK(87) GREEN POLA RITY SELECT [...]

  • Página 12

    CS-2004TW1 ANTENNA The following diagram pertains to t he CS-2004TW1 two-way paging model only: WINDSHIELD ANTENNA LOCA TIONS CS-2004TW1 Black P lug Blue Plug RECOMMENDED Note Orientation of Black & Blue Pl ugs. Colors must match, or system will not operate! Transceiv er Box CS-2004TW1 Antenna System W indow M ount Antenna 12[...]

  • Página 13

    OPTION PROGRAMMING Soft.686 You can program each option individually or multiple options in one session. You may start with the lowest option # and continue on to higher options wit hout repeating the steps #1 through 3. To Engage Option Programming: 1. Turn Key to the ON position. 2. Press program / valet button 5 times, after a few seco nds the u[...]

  • Página 14

    OPTION PROGRAMMING 1. AUTOLOCK WITH IGNITION This option controls whether the doors w ill automatically lock when the ignition is turned on and w ill unlock when the ignition is turned off. 2. PASSIVE ARMING This option controls the Passive (Automatic) arming feature. If ON, arming will occur 30 Seco nds after the ignition is turned off and the las[...]

  • Página 15

    OPTION PROGRAMMING 9. OPEN DOOR/ZONE WARNING (5 or 60 Seconds) This setting changes the delay time in which the alarm system begins t o monitor the Door Zone. This is helpful on vehicles with delayed dome lights. It prevents the alar ms warning chi rps due to extended dome light circuit. 10. DOOR LOCK/UNLOCK PULSE TIME Controls the amount of time ([...]

  • Página 16

    CS-2004TW1 / CS-2004DC II REMOTE PROGRAMMING TRANSMITTER PROGRAMMING NOTES (Read first!): (1) The CS-2004TW1 will learn up to 4 remotes, any co mbination of special CS-398TW 1-Way or CS-389LED 2- Way pager remotes. (2) The CS-2004DC II will up to 4 CS-404T X remotes. The remote controls for the CS-2004DC II and the CS- 2004TW1 systems ARE NOT inter[...]

  • Página 17

    CS-2004TW1 / CS-2004DC II REMOTE PROGRAMMING IGN OFF WAIT F O R 4 FL A S H ES PRESS 4 X's FLA SH 2, 3, or 4 X' s IGN OFF PRESS TOGETHER "TW 1" OR SLNT AU X "DC" PRESS LOCK BTN SLNT AUX 17[...]

  • Página 18

    OPERATION SLNT AUX ARM/ DISARM/ UNLOCK LOCK PA G I N G LED's SILENT/ AUX. 2 ANTENNA FIXED AUX. 1 #1 #2 #3 #4 CS-2004T W1 LE D P AGI NG REMO TE CS-2004DC II / CS-2004TW1 remote controls: SLNT #3 #1 #2 #4 LOCK TRU N K SILENT/ UNLOCK VEHICLE 2 FLA SHLIGH T AU X . # 1 AU X . # 2 AUX CS -2004 DC II CS-2004TW1 TWO-WAY PAGER OPERATION & PAGE TONE[...]

  • Página 19

    OPERATION ACTIVE ARMING To arm the alarm and lock the doors, press the #1 Button on any remote. You will hear a single siren chirp and the lights will flash once. The system will arm, the doors will lock (optional) and t he starter will be disabled. The red in- dash LED in the vehicle will begin to flash. After a short delay of 10-15 seconds to all[...]

  • Página 20

    OPERATION SHOCK / IMPACT PROTECTI ON WITH PRE-WARNING Once the system is armed, if a low-level shock to the vehi cle body is detected, the pre-warning sensor activates wi th 5 siren chirps and one light flas h as a Warn-Away feature. If a hard impact to the vehicle is detected the system will go into a full trigger cycle fo r 20 seconds. Adjust the[...]

  • Página 21

    OPERATION PASSIVE ARMING / PASSI VE LOCK MODES (PROGAMMABLE) If programmed, passive (Automatic) Arming will occur 30 Seconds after the ignition is turned off and the last door has been closed. The lights will flas h twice when the last door is closed and the LED will begin flashing rapidly while counting down. If a door is reopen ed the countdown w[...]

  • Página 22

    OPERATION CS-2004TW1 LED TRANSCEIVER (LOW BATTERY WARNING) CR2032 3V Lithium Battery T wist and Remove Battery cover w ith a Coin or Screwdriver Larger "+" Posi tive side of battery faces up CS2004TW1 BA TTER Y REPLACEMENT The CS-2004TW1 LED has a low battery warning system. When the battery voltage is low, the LED pager remote will stop [...]

  • Página 23

    2-VEHICLE OPERATION: (CS-2004DC II SYSTEM ONLY) 2-Vehicle method (C S-2004DC II SYSTEM ONLY): Your CS-2004DC II remote includes a push-button on the side for 2-car operation. You can only operate a second vehicle with a CS-2004DC II system installed. Your remote must be progra mmed to the second vehicle first. Read the following setup and operation[...]

  • Página 24

    CARJACK PROTECTION PROGRAMMABLE PASSIVE CARJACK This feature provides Passive Carjack protection a nd must be enabled before us e through Alarm programming options #7 & #12 on page 13. We reco mmend this mode should only be used in serious situations. When the Ignition is on (vehicle is running ), and a door is opened, then closed, the Carjack [...]