Dacor 100500 manual

Part No. 100500 Rev . A I n s t a l l a t I o n I n s t r u c t I o n s B u I l t - I n r e f r I g e r a t o r s[...]

[...]

1 Refrigerator Safety ....................................................................... 1 Design Specifications ............................................................... 2-6 Product Dimensions .................................................................... 2 Door Swing Dimensions ....................................................[...]

2 d ooR s wing d imensions The area to the left and the right of the appliance must permit both doors to open to a minimum of 90°. Allow a minimum of 2 1/2” (64mm) space between the side of the refrigerator doors and a corner wall. NOTE: More clearance may be required if using an overlay panel or custom handles. P RoduCT d imensions ◊ The?[...]

3 H (A) Grille Panel H W (C) Non-Dispenser Freezer Panel W (D) Refrigerator Panel W H W H1 H2 W1 W2 (B) Dispenser Freezer Panel d esign s PeCifiCa Tions C usTom o veRla y P anels The decorator panels for overlay models cover the door trim for an attractive, seamless look that flows into the overall design of the room. This application is often acco[...]

4 Overlay Panel Specifications (See Illustrations on page 3.) 42-Inch Model 48-Inch Model BACKER P ANEL (A) Grille Panel W Width 40 1/4” (1022mm) 46 1/4” (1 175mm) H Height 8 3/4” (222mm) 8 3/4” (222mm) (B) Freezer Dispenser Panel W Width 16 1/4” (413mm) 18 1/2” (470mm) W1 Width 2” (51mm) 2” (51mm) W2 Width 14 1/2” (368mm) 14 1/2?[...]

5 d esign s PeCifiCa Tions Custom T oe Kickplate Specifications If using custom toe kickplate with your Dacor ® Built-In Refrigerator , refer to the following specifications. “C” 3" 3 3/4" R. 1/2" Non-Dispenser 2 3/16" T yp 7/8" 5/16" 4 13/16" 5 5/8" 1 1/8" T yp 6 1/4" 15/16" T yp Panel th[...]

6 d esign s PeCifiCa Tions 0" 3/4" Overlay Panel 1/4" 90˚ Door Opening (T op View) 23 7/8" to Rear of Cabinet Cabinet T rim Door Open @ 90˚ Door Closed 1/2" 3/4" 1" 1 1/4" 1 1/4" 1" 3/4" 1/2" 1/4" 0" 1 1/2" 1 3/4" 2" 2 1/4" 2 1/2" 2 3/4" 3" 3 [...]

7 i nsT alla Tion s PeCifiCa Tions T ools and P aRTs IMPORT ANT : ◊ Installer: Leave these Installation Instructions with the homeowner . ◊ Homeowner: Keep these Installation Instructions for future reference. Save these Installation Instructions for the local electrical inspector’s use. T ools needed: Make sure that you have the necessary to[...]

8 Rough-In Dimensions ◊ The solid sofit or ceiling should be within 1” (25mm) above the refrigerator. If the solid sofit is higher than 1” (25mm) or one is not available, then the refrigerator must be braced to prevent tipping during use. If the anti-tip blocking is need. (see “Anti-T ip Blocking” on page 9) NOTE: A clearance of 1/2” (1[...]

9 i nsT alla Tion i nsTRuCTions u nP aCk R efRigeRa T oR W ARNING TIP OVER HAZARD – Refrigerator is top heavy and tips easily when not completely installed, Keep doors taped closed until refrigerator is completely installed. Use two or more people to move and install refrigerator . Failure to do so can result in death or serious injury . IMPORT A[...]

10 i nsT alla Tion i nsTRuCTions w a TeR l ine C onneCTion P lug in R efRigeRa ToR m ove u niT To f inal P osiTion IMPORT ANT : T o prevent floor damage, make sure levelers are raised (not touching the floor) and the unit is on rollers before moving. ◊ Place top of cardboard carton or plywood under refrigerator . Remove unit from dolly . ◊ Do n[...]

1 1 i nsT alla Tion i nsTRuCTions i nsT all C usTom P anels Panel Installation Before you begin installing panels, refer to the “Custom Panel Specifications” for overlay models and verify that you are working with the panel design called for in your installation. If you have chosen the stainless steel design, your refrigerator has been shipped [...]

12 7. Remove the four #15 T orx plastic collar screws from the fountain/escutcheon collar . 8. Place the fountain/ escutcheon collar onto the backer panel. Use tape to hold in place. 9. Open the freezer door and slide panel onto the door . 10. The holes in the fountain/escutcheon collar should line up with the mounting holes in the door panel. Reve[...]

13 i nsT alla Tion i nsTRuCTions Side Panel Installation If using side panels with the Dacor ® Built-In Refrigerator , they will need to be 1/4-inch thick. Slide the panel into position and secure with screws indicated by the shaded area. A 3/16-inch spacer is required between the cabinet and side panel. A 1/2-inch thick by 10 1/4- inch tall space[...]

14 The importance of the proper installation of your Dacor Built-In Refrigerator cannot be overemphasized. Proper installation is the responsibility of the homeowner . IMPORT ANT : T o ensure a safe and proper installation, the following checklist should be competed by the installer to ensure that no part of the installation has been overlooked. An[...]

15 n oTes[...]

16 n oTes[...]

[...]

Web Site: www .dacor .com Phone: (800) 793-0093 The information and images in this book are the copyright property of Distinctive Appliances, Inc. Neither this book nor any information or images contained herein may be copied or used in whole or in part without the express written permission of Distinctive Appliances, Inc. ©Distinctive Appliances,[...]