Datamax O'Neil MicroFlash 2Te manual

MICROFLASH 2T e 110228-002 User Guide[...]

T ABLE OF C ONTENTS microFlash 2t e Printer: Top View ..... ........... 1 Using the Batter y: General Guidelines ........ 2 Charging the Battery ................ ............... .... 2 Determining Battery Conditio n .. ................. .. 2 Installing Paper ......... ............ ............ ........... 3 Printing a Self-Test .......... .........[...]

MICROFLASH 2T e PRINTER USER'S GUIDE 1 microFlash 2t e Printer: Top View Charge LED Paper/ Paper Cavity Data Port Roller Self-Test Button Print Head Release Lever RF Power LED Power P ort Figure 1 Figure 2 ON/OFF Status LED Latch LEDs NOTE: When the cable plug is inserted into the P ower Po rt, the cable plug must lay hori zontally to the bott[...]

MICROFLASH 2T e PRINTER USER'S GUIDE 2 Using the Battery: General Guidelines If the printer has not been used for a long period of time, it may be necessary to rech arge the battery . For more information, see Chargi ng the Batt ery on page 2 . Charging the Battery If the battery is low when the printer “wakes up, ” the printer sounds thre[...]

MICROFLASH 2T e PRINTER USER'S GUIDE 3 Installing Paper 1. Insert a roll of paper with the end of the roll exiting from the bot tom of the pape r cavity (Figur e 3). 2. Open the print head by raising the green, print head release lever until it stops (Figure 4). 3. W ake up the printer by briefly pressing the gr een, self -test butto n (Figure[...]

MICROFLASH 2T e PRINTER USER'S GUIDE 4 4. Feed the end of the paper under the rol ler . The paper automatically feeds under the roller and exits from the t op of the print he ad. V erif y the paper exits straight. 5. Lower the green, print head release lever (Figure 6). 6. Fe ed the paper through the printer's cov er (Figure 7). 7 . Close[...]

MICROFLASH 2T e PRINTER USER'S GUIDE 5 Clearing Linerless Paper Jams A paper jam may occur if an Datamax -O’Neil printer with linerless paper instal led is left in a cold environment without being used for an extended period of time (such as overnight). Removing a Paper Jam 1. Open the print head by raising the print head release lever until[...]

MICROFLASH 2T e PRINTER USER'S GUIDE 6 Remo ve the Linerless Paper fr om the Print Head If the printer is going to be in a cold environment for a long period of time, remove the linerless paper from the print head. The paper can remain in the printer . Advance the P aper When the printer is turne d on, hold the paper and then advance the paper[...]

MICROFLASH 2T e PRINTER USER'S GUIDE 7 Cleaning Guidelines The following steps are intend ed to show how t o clean MF2T e printers that use receipt media. These steps do not include cleaning media with adhesives. The printer needs to be cleaned when any of th e following conditions occur:  Debris is on the printhead or after every ten (10) [...]

MICROFLASH 2T e PRINTER USER'S GUIDE 8 Figure 13 - dirty roller Figure 14 - faded prin tout[...]

MICROFLASH 2T e PRINTER USER'S GUIDE 9 Figure 15 - faded printout[...]

MICROFLASH 2T e PRINTER USER'S GUIDE 10 Cleaning the Printhead 1. Open the case. 2. Raise print head r elease le ver . Figure 16 Figure 17[...]

MICROFLASH 2T e PRINTER USER'S GUIDE 11 3. T ear open the cleaning card’s packaging. 4. If the printer is not awake, briefly press the red self- test button. The printer will automatically feed the cleaning card, the ca rd will feed under the roller a nd then exit the top of the print head. 5. When the card is in the pro per position, lower [...]

MICROFLASH 2T e PRINTER USER'S GUIDE 12 K eep the lid open to allow the printer to dry . After feeding the card throug h the printer once, remove and discard the cleaning card. Configuring the Printer The printer has many configurable set tings. T o configure or upgrade firmware, download the latest Windows configuration pr ogr am at www .data[...]

MICROFLASH 2T e PRINTER USER'S GUIDE 13 Using Prin ter Data Cables 1. Select the appropriate cable f or use with the host/ device you are using. 2. Insert the plug into the printer data port (Figur e 12). 3. Lead the cable thr ough the notch on the outside of the printer cover . 4. With the cable exiting t he front of the pr inter , close and [...]

MICROFLASH 2T e PRINTER USER'S GUIDE 14 Using Blueto oth Radio printers are configured with def ault factory settings. T o determine your printer's radio configuration, print a self -test. (F or more information, see Printing a Self - T est on page 4 . ) If you have multiple printers, configure them specifically for use in your environmen[...]

MICROFLASH 2T e PRINTER USER'S GUIDE 15 Using Buttons, LEDs, and Audio Indicators Button Functions LED Indicators Bluetooth LED Indicators Green Self-Test Button Short press If printer is asleep; printer wakes up. If printer is awak e; paper feeds. Long press (press and hold for five seconds) Prints a self -test. Bluetooth Power Button Short p[...]

MICROFLASH 2T e PRINTER USER'S GUIDE 16 Charge LED Indicators Power LED Indicato rs LED State of Charge Action Flashing Orange Flashing Red Charge in progress . W ait for the charge LED to turn green. Green Charge complete. None. Red fl as h - slow Battery is too cold. Change environment. Red fl as h - fast High temperature. Change environment[...]

MICROFLASH 2T e PRINTER USER'S GUIDE 17 Audio Indicators CardReader Audio Indicators Beep(s) Description Action 1P r i n t e r w a k e s u p . N o n e . 2 Out of paper . Install paper . 3 Low battery . Charge battery . 1 short RF power is on (when blue, RF power but t on is pressed and power w as turned off ). None. 2 short RF power is off (wh[...]

MICROFLASH 2T e PRINTER USER'S GUIDE 18 Using a CardReader General Guidelines T o use the CardReader , swipe a card with the stripe facing tow ard the printer , then slowly move the card left or right in the CardReader slot. Fo r information on Ca rdRe ader LED indicators and audio indicators, see Using Buttons, LEDs, and Audio Indicators on p[...]

MICROFLASH 2T e PRINTER USER'S GUIDE 19 Agency Approvals FCC Notice This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmf ul interference in a residentia l installation. This equipment genera[...]

MICROFLASH 2T e PRINTER USER'S GUIDE 20 Applicable Di rective • 89/336/EEC, 73/23/EEC Applicable Standards • EN55022 (1998) • EN55024 (1998) • EN60950 (1992)[...]

MICROFLASH 2T e PRINTER USER'S GUIDE 21 Copyright This manual and an y examples co ntained herein ar e provide d “as is” and are subject to change withou t notice. Datamax -O’Neil makes no w arranty of any kind with re gard to this manual, including, bu t not limited to , the implied warr anties of merchantabilit y and fitness f or a par[...]

MICROFLASH 2T e PRINTER USER'S GUIDE 22 Media Supplies Datamax -O’Neil offers sev en certified grades of paper for use in the printers. Our certified supplies are guaranteed compatible — this important qualification means that rigorous performance and image lif e testing have been perf ormed. Quality supplies are key to obtaining optimal i[...]

[...]

COPYRIGHT © 2010, DA T AMAX-O’NEIL[...]