Delta Electronics Ethernet Communication Module DVPEN01-SL manual

DVPEN01-SL Ethernet Communication Module Application Manual[...]

[...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 1 Warning 3 Please r ead this instruction car efully before use and follow th is instruction to operate the device in order to pr event damages on the device or injuries to staff. 3 Switch off the power befor e wiring. 3 RTU-DNET is an OPEN TYPE device and ther efor e should be ins[...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 2 5.6 IP Filter ..................................................................................................................................... 23 5.7 S tatic ARP T able ..........................................................................................................[...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 3 1 Introduction Thank you for choosing DVPEN01-SL module. T o correctly inst all and operate DVPEN01-SL, please read the manual carefully before using the module. DVPEN01-SL is an Ethernet communication module for remote setting and communication through WPLSoft. DVPEN01-S L is ab[...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 4 Item S pecification Vibration/ Shock Resistance S tandard: IEC61 13 1-2, IEC 68 -2-6 (TEST Fc)/IEC61 131-2 & IEC 68-2-27 (TEST Ea)  Electrical specifications Item S pecification Power supply voltage 24VDC (-15% ~ 20%) (Power is supplied by the internal bus of MPU.) Power c[...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 5 2.3 LED Indicators Indicator Color Indication POWER Green Power indication RS-232 Red Communication st atus of the series port 100M Orange Network connection st atus LINK Green Network communication speed 2.4 RJ-45 PIN Definition RJ-45 sketch Terminal No. Definition Explanation 1[...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 6 Connect DVPEN01-SL to the Network Connect DVPEN01-SL to t he Ethernet Hub by twisted pair cable CA T -5e. DVPEN01-SL has Auto MDI/MDIX function; therefore, DVPEN01-SL do es not need to use a crossing cabl e between the PC and DVPEN01-SL. Network connection between the PC and DVPE[...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 7 CR# HW LW Attribute Content Explanation #7 R S tatus of E-Mail 1, 2 b0 ~ b7: Current status of E-Mail 2 b8 ~ b15: Current status of E-Mail 1 #8 R S tatus of E-Mail 3, 4 b0 ~ b7: Current status of E-Mail 4 b8 ~ b15: Current status of E-Mail 3 #9 R/W E-Mail 1 additional message Fil[...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 8 CR# HW LW Attribute Content Explanation #1 19 R/W Modbus TCP data length Setting up the data length for Modbus TCP transactio n #219 ~ #120 R/W Modbus T C P data buffer Data buf fer of Modbus TCP for storing sending/receiving data #248 ~ #220 - Reserved #251 R Error co de Display[...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 9 CR value E-Mail status 10 Fail to connec t to SMTP-Server 1 1 Incorrect recipient E-Mail addre ss 12 SMTP-Server communication error 13 Exceeding the max. number of TCP con nection 3 ~ 9, 14 ~ 255 Reserved CR#9 ~ 12: E-Mail 1 ~ 4 Additional Message Explanations: The user fills in[...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 10 S toring the data to be transmitted to the remote MPU. CR#49 ~ 68: Data Receiving Buf fer Explanations: S toring the data received f r om the remote MPU. CR#81: Read Address for Data Excha nge Explanations: Setting up manually the Modbus addres s of the regist er for Slave dat a[...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 11 CR#70, 71: IP Address Explanations: 1. Setting up the IP address of our equipment in hex. When in DHCP mode, you can only read and cannot write. 2. Example: Assume you’d like to set the IP address as 192.16 8.0.2, y ou have to write H’0002 into CR#70 and H’C0A8 into CR#71 [...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 12 CR#1 16: Modbus TCP S tatus Explanations: Displaying the current communication st atus of Modbus TCP mode . When the CR value is set as”0” Æ the dat a have not yet been received; when the CR value is set as “1” Æ the data exchange is in progress; when the CR value is s[...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 13 registers (CR) in the extension module. Numbering of the modules: Every extension modul e conne cted to PLC MPU has a No. to allow you to know which module is which when compili ng the PLC program. The first extension module att ached at the left hand side of the PLC MPU is numb[...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 14 2. Auto-search • Press “Auto-Search” (circl ed) to search for every DVPEN01-SL in the network and display them in the left column. • Move the cursor to the module you would like to set up. Double cli ck it to enter the setup page. • You will see the basic setup page a [...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 15 3. Searching by IP address • Set the transmission type as “Ethernet” first. Next c lick on the “Stat ic IP Search” icon (circled) to search for the designated IP. • Press the “search” icon and you will open the wind ow for entering the IP addres s. Enter the IP o[...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 16 4. Opening DVPEN01 - SL setup page by RS-232` • Select “RS232" as the transmission type in co mmunication setting. You will have to designate a communication port. When DVPEN01-S L is searc hed by RS-232, you do not need to set up the parameters (i.e. data length, parit[...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 17 • Module Name: There can be many DVPEN 01-SL modules in the network. Thus , you can set up a module name for each module to identify the module when you need to use them. • Module Language: Y ou can select a language for each module nam e, and the windows will be displ ayed [...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 18 sections), bordered by meridian s each 15° of longitude apart. The local time in n eighboring zones is then exactly one hour dif ferent. However , political and geographical practicalities can result in irregularly shaped zon es that follow political bounda ri es or that change[...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 19 • Enter 192.168.0.1 into IP address. Click on “OK” to complete the IP address setting of the PC. 2. Setting up DVPEN01-S L Network • IP configuration: There are two types of IP, static IP and DHCP. S tatic IP: Preset or manually modified by the user . DHCP: Automatically[...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 20 IP Explanation Static The user e nters the IP address, subnet mask and gateway . DHCP DHCP server offers the IP address, subnet mask and gateway. • IP address: IP address is the location of the equipment in the network. Every equipment connected to the network has to have an I[...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 21 1. SMTP Server: The E-Mail will first be sent to SMTP server , and SMTP server will send it to the designated address. For example, assume there is an E-Mail to be sent to test@delt a.com.tw , and the SMTP server is 172.16.144.121. The E-Mail will be sent to SMTP server first, a[...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 22 5. Select recipient s: After you have set up all the parameters for the E-Mail, you will need to select recipients. The E-Mail will be sent to the designated recipients w hen the E-Mail is triggered. T o trigger E-Mail, set the value is CR#3 ~ CR#6 as “1”. 6. See “Applicat[...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 23 1. Enable Data Exchange: Check the box to enable or disable dat a exchange. S tart data exch ange after enable it. 2. Communi cation Address & Data exchange host IP: Y ou have to enter the IP address of DVPEN01-SL at the other end. For example, if you would like DVPEN01-SL t[...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 24 1. Enable IP Filter Function: Check the box to enable IP filter . 2. IP: IP addresses that are allowed to establish connections. Maximum 8 IPs are allowed. 3. Netmask: The subnet of the IP is allowed to establish a connection. T o see whether the destination IP is allowed, condu[...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 25 1. IP: Destination IP address in data transmission. 2. MAC: The MAC address corre sponding to the IP address. Note: Incorrect settings may result in connection failu re. The refore, DO NOT set the MAC address of the equipment without the network into the t able. 5.8 Setting up P[...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 26 1. Modify: Check the box to modify the passwo rd. 2. New Password: Maximum 4 characters are allowed. Lea ve the column “blank” to disable the p assword protection function. 3. Confirm Password: Enter the new password a gain. 4. See “Application Examples Section 6.4” for [...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 27 Check “Default Setting” box and click on “Y es”. Note: If you set up DVPEN01-SL by RS-2 32, you can return the setting to default setting whether the password is l o cked or not. It t a kes approximately 10 seco nds to return to default setting, so DO NOT switch off the [...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 28 1. Export: Save all the settings of DVPEN01-SL into *.eni files. The exported files do not incl ude the pass word . 2. Import: Select a file and the file will be imported to all the settings. 5.11 Recording IP Address When DVPEN01-SL is searching for a des ignated IP , there is [...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 29 Input IP Address: Press “Add” to record the IP address of the module into the list. 6 Application Examples 6.1 Setting up IP and Communicating through WPLSoft Application Setting up network parame ters of DVPEN01-SL directly on the PC. Network requirement (1) IP of PC execut[...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 30 4. Click on “Auto-Search” icon to search for all DVPEN01-SL modules in the network. 5. Designate a DVPEN01 -SL and double click it to open the setup page.[...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 31 6. Open “Basic” setup page. 7. Switch to “Network” setup page[...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 32 8. Enter IP address: 192.168.0.4; Netmask: 255.255.255.0; Gateway: 192.168.0.1. Press “OK” to complete the setup, and WPLSoft will automatically search for DVPEN01-SL. 9. The IP of DVPEN01-SL ha s been modified into the new setting (DELTA DVPEN01-SL: 192.168.0.4). 10. Click [...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 33 PC Hu b DH CP Serve r PC DV P-PLC DV PEN 0 1 2. Open “Communication Setting” in WPLSoft. 3. Select “Ethernet” and press “OK ” .[...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 34 4. Click on “Auto-Search” icon to search for a ll DVPEN01-SL modules in the network. Follow “View Æ Workspace Æ Communication” or “View Æ Workspace Æ Projec t” to find the detected DVPEN01-SL module (default module name: DELT A DVPEN01-SL, IP: 192.168. 1.5) in th[...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 35 6. Open the setup page. You can modify the module na me for easier identification. 7. Next, set up the new IP of DVPEN01-SL. First sw itch to “Network” setup page. If there is a DHCP server in the LAN, select DHCP in “IP Configuration”. If there is no DHCP server in the [...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 36 6.3 Setting up IP and Communicating through WPLSoft Application Setting up network parame ters of DVPEN01-SL by ladder diag ram Network requirement (1) IP of DVPEN01-SL: 192.168.0.4 (2) Subnet mask: 255.255.255.0; Gateway: 192.168.0.1 (3) If DVPEN01-SL is damaged, change to a ne[...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 37 • Use T O instruction to write the network se tting parameters D0 ~ D7 into CR#69 ~ #75 in DVPEN01-SL. DVPEN01-SL is the first extension module numbered K100 attached at the left hand side of PLC. (See 4.3 for more det ails.) • After the program is being executed, all the pr[...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 38 4. Open the setup page again, and DVPEN01-SL is now lo cked by the passwo rd. You cannot open any of the settings now. Click on “Unlock” to leave the entering password window. 5. Enter the password to temporarily unlock the protecti on and modify the parameters. If you close[...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 39 6. To clear the password, simply leave the passw ord columns bl ank. Click on “OK” to clear the password. 7. After the password is cleared, you can modify the parameters. 6.5 When the Password is Lost (Returning to Default Setting by RS-232) Application Returning to default [...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 40 2. Check the “Default Setting” box an d the “Warning” dialog box will appear. Click on “Yes” to ret urn to default setting (in approx. 5 ~ 10 seconds), and the password will be cleared as well. 3. After the searching, all the parameters ha ve already returned to thei[...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 41 3. Check “Enable IP Filter Function” box. Enter “1 92.16 8.0.7” in No. 1 IP and “255.255.255.255” in all “Netmask” columns. 4. Enter “192.168.0.1” in No. 2 IP and “255.255.255.0” in No.2 “Netmask” column. Click on "OK” to complete the setting. [...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 42 6.7 Setting up S tatic ARP T able Application Setting up sta tic ARP table Network requirement (1) MAC address of equipment 192.168.1.6 is 00:18:23:10:00:35 (2) MAC address of equipment 192.168.1.1 is 00:18:23:10:00:04 1. See 6.1 for the connection and how to set up the communic[...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 43 Note: The MAC address of D VPEN01-SL can be obtained from WPLS oft or the MAC address sti cker on the equipment. The MAC address of PC can b e found in the “Network Conn ection Details” (see below). 6.8 Application of E-Mail Application Sending an E-Mail to notify the admini[...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 44 3. In “Subject and Mail” page, enter the ad dress of SMTP server, subject of E-Mail, and E-mail address of the recipient. 4. Switch to “Select Recipients” page. Ch eck all the boxes of “Recipient 1”. C lick on “OK” to complete the setting.[...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 45 5. After all the settings in DVPEN01-SL are comp leted, compile the ladder diag ram in the MPU and download it to the MPU. See below for the program design: END X0 T0 K100 K3 K1 K4 K5 K6 K1 X0 T0 K100 K1 K1 T0 K100 K1 K1 T0 K100 K1 K1 Y0 Y0 Explanations: • If the rising-edge o[...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 46 3. Check “Enable Data Exchange” b ox. Enter IP address of PLC_A “192.168.0.4” in No. 1 Data Exchange Host IP column. Click on “OK” to complete the setting. 4. After all the settings in PLC _ B are completed, compil e the ladder diagram in the MPU and download it to P[...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 47 • Write the dat a in RTC into CR#29 ~ CR#35. • Write “1” into CR#13 to st art the data exchange. • CR#14 = 2 refers to successful excha nge. CR#14 = 3 refers to failed exchange. 5. Compile the ladder diagram for PLC_A and do wnload it to PLC_A. END M101 3 K7 D0 K49 K10[...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 48 Explanations: • The data exchange will be executed every one second. • Write “0” into CR#28, and PLC_B will u s e CR# 25 ~ CR#26 as the IP address of the destination PLC. • Write the IP address of PLC_A into CR#25 and CR#26. The first two IP codes (192.168 = H’C0A8) [...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 49 END SET M2 M1 RS T K100 K1 M2 K14 D1 4 RS T M2 RS T M2 = D 1 4 K 2 = D 1 4 K 3 FRO M K100 K1 TOP K100 TO P K1 K 1 K0 K1 4 K13 K100 TO P K1 K86 H106 4 Explanations: • The data exchange will be executed every one second. • Write “0” into CR#28, and PLC_B will u s e CR# 25 [...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 50 M1013 K100 K1 K100 K100 K1 M2 M1 M1 SET M1 TOP TOP TOP K100 TOP K1 K100 K1 TOP K100 TOP K1 K1 K0 H4 HC0A 8 K1 H0 K100 K100 K1 TOP TOP K100 TOP K1 K1 K1 H0 H5 H5 K100 TOP K1 K100 K100 K1 TOP TOP K100 TOP K1 K1 H0 H0 K6 HFF K1 18 K1 17 K1 1 1 K120 K121 K122 K123 K124 K125 K1 19 K1[...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 51 • Write the length of the instrcutio n into CR#1 19. • Write “1” into CR#1 15 to start the ex ecution of Modbu s TCP instrcution. • CR#1 16 = 2 refers to successf ul execution. CR#1 16 = 3 refers to failed execution. • If the execution is successful, Y0 on PLC_A will[...]

Ethernet Communication Module DVPEN01-SL DVP-PLC Application Manual 52 MEMO[...]