Desa SDVBNC manual

NA TURAL GAS BURNER SYSTEM MODEL SDVBNC PROP ANE/LP GAS BURNER SYSTEM MODEL SDVBPC REMOTE READY FOR YOUR SAFETY WHAT TO DO IF YOU SMELL GAS • Do not try to light any appliance. • Do not touch any electrical switch • Do not use any phone in your building. • Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier[...]

107304-01D For more information, visit www.desatech.com For more information, visit www.desatech.com 2 SAFETY INFORMA TION IMPORTANT: Read this owner’s manual carefully and completely before trying to assemble, operate, or service this stove and burner system. Improper use of this stove and burner system can cause serious injury or death from bur[...]

107304-01D For more information, visit www.desatech.com For more information, visit www.desatech.com 3 3 P I L O T O F F P I L O T O N H I LO IN OUT SAFETY INFORMA TION Continued PRODUCT IDENTIFICA TION Figure 1 - DESA Direct-Vent Burner System Shown Installed in Approved Cast Iron Stove Body (Vanguard Models SCIVFC/ PSCIVFC Series Shown) 6. Carefu[...]

107304-01D For more information, visit www.desatech.com For more information, visit www.desatech.com 4 LOCATION AND SPACE REQUIREMENTS Determine the safest and most efficient location for your cast iro n sto ve. Make sure that rafters and wall studs are not in the way of the venting system. Choose a location where the heat output is not affected by[...]

107304-01D For more information, visit www.desatech.com For more information, visit www.desatech.com 5 5 6 " 4 " Front 4" 36" from Front 42" Ceiling Floor from Back Wall 29" 4" 4" Figure 3 - Clearances for Standard Installation Figure 4 - Clearance for Corner Installation Figure 5 - Stove With Burner System B[...]

107304-01D For more information, visit www.desatech.com For more information, visit www.desatech.com 6 Figure 10 - Attaching Stove Legs Bottom Of Stove Unit Leg Bolt Washers 6. Remove all contents from inside stove cavity . Contents include: (1) - Stove bottom (Discard - Not used with this application) (4) - Legs with leg leveler bolts (1) - Bottom[...]

107304-01D For more information, visit www.desatech.com For more information, visit www.desatech.com 7 7 CAST IRON STOVE AND DIRECT -VENT BURNER SYSTEM ASSEMBL Y Continued Adjusting Nut Bolt Stop Catch Bolt Door Claw Door Figure 12 - Catch Bolt and Door Claw Orientation 14. Lay the front panel assembly face down on a protected sur - face. Remove th[...]

107304-01D For more information, visit www.desatech.com For more information, visit www.desatech.com 8 NOTICE: If installing blower in an existing stove burner system with gas connections, shut off gas supply and disconnect heater from gas supply. Con- tact a qualified service person to do this. INSTALLING OPTIONAL BLOWER ACCESSORY INSTALLING THE B[...]

107304-01D For more information, visit www.desatech.com For more information, visit www.desatech.com 9 9 CAST IRON STOVE AND DIRECT -VENT BURNER SYSTEM ASSEMBL Y Continued 4. Thermostat Blower Onl y: Attach thermal switch and bracket to inside rear cover wall with two hex head screws provided as shown in Figure 17, page 8. After securing bracket to[...]

107304-01D For more information, visit www.desatech.com For more information, visit www.desatech.com 10 TPTH TPTH TP TP TH TH LOCATION OF VENT TERMINATION When locating vent termination, it is important to observe the minimum clearances shown in Figure 21, page 11. *Check with local codes or with the current CAN/CSA B149[.1 or .2] Installation Code[...]

107304-01D For more information, visit www.desatech.com For more information, visit www.desatech.com 11 11 Fixed Closed Openable Fixed Closed Openable V V V V V V V V X X V X G G J F B B K N H I A N E L D B M A C B V V A G G B TERMINA TION CAP AIR SUPPL Y INLET GAS METER RESTRICTED AREA (TERMINA TION PROHIBITED) A = clearance above grade, veranda, [...]

107304-01D For more information, visit www.desatech.com For more information, visit www.desatech.com 12 WARNING: Read all instructions completely and thoroughly before attempting installation. Failure to do so could result in serious injury, property damage or loss of life. Operation of improperly installed and maintained venting system could resul[...]

107304-01D For more information, visit www.desatech.com For more information, visit www.desatech.com 13 13 INSTALLATION FOR HORIZONTAL TERMINATION Snorkel terminations are available for terminations requiring a vertical rise on the exterior of the building (see Figures 22 and 23). Snorkel kit VKS-47-K is also available (see page 19). Fol- low the s[...]

107304-01D For more information, visit www.desatech.com For more information, visit www.desatech.com 14 VENTING INST ALLA TION Continued Figure 26 - Installing Horizontal Vent Cap (Noncombustible Exterior) WARNING: Do not recess vent termination in to any wall. This will cause a fire hazard. Figure 27 - Installing Vinyl Siding Standoff (Combustible[...]

107304-01D For more information, visit www.desatech.com For more information, visit www.desatech.com 15 15 Figure 31 - Horizontal Termination Configuration for Venting Using Two 90 ° Elbows with Termination at 90 ° with Stove Figure 29 - Horizontal Termination Configuration for Venting Using One 90 ° Elbow Horizontal V enting V ertical (V) Horiz[...]

107304-01D For more information, visit www.desatech.com For more information, visit www.desatech.com 16 1. Determine the route your vertical venting will take. If ceiling joists, roof rafters, or other framing will obstruct the venting system, consider an offset (see Figure 32) to avoid cutting load bearing members. Note: Pay special attention to t[...]

107304-01D For more information, visit www.desatech.com For more information, visit www.desatech.com 17 17 Vertical Termination Configurations Figure 36 through 39 show four different configurations for vertical termination. All connections must be sealed with high temperature silicone sealant as specified in the second warning statement on page 12[...]

107304-01D For more information, visit www.desatech.com For more information, visit www.desatech.com 18 V enting with T wo 90 ° E lbows V ertical (V 1 ) Horizontal (H) 5' min. 6' max. 6' min. 12' max. 7' min. 18' max. 8' min. 20' max. Note: V ertical (V 1 ) + V ertical (V 2 ) = 20' max. Figure 38 - Vert[...]

107304-01D For more information, visit www.desatech.com For more information, visit www.desatech.com 19 19 VENTING INST ALLA TION Continued HIGH ALTITUDE INSTALLATION Your cast iron stove and direct-vent burner system has been CSA tested and approved for operation at altitudes in the USA from 0- 2000 ft. and in Canada from 0-4500 ft. When installin[...]

107304-01D For more information, visit www.desatech.com For more information, visit www.desatech.com 20 CAUTION: Use only new, black iron or steel pipe. Internally-tinned copper tubing may be used in cer- tain areas. Check your local codes. Use pipe of 1/2" diameter or greater to allow proper gas volume to burner system. If pipe is too small, [...]

107304-01D For more information, visit www.desatech.com For more information, visit www.desatech.com 21 21 WARNING: Use pipe joint sealant that is resistant to liquid petroleum (LP) gas. We recommend that you install a sediment trap/drip leg in supply line as shown in Figure 41, page 20. Locate sediment trap/drip leg where it is within reach for cl[...]

107304-01D For more information, visit www.desatech.com For more information, visit www.desatech.com 22 TPTH TP TH Figure 46 - Control Valve Terminals To Control Switch or Optional Accessory INSTALLING OPTIONAL WALL MOUNT SWITCH - GWMS2 1. Connect one terminal of 25 ft. wire for the wall switch to the TPTH terminal on the valve. Connect remaining w[...]

107304-01D For more information, visit www.desatech.com For more information, visit www.desatech.com 23 23 STOVE AND DIRECT -VENT BURNER SYSTEM INST ALLA TION Continued INSTALLING OPTIONAL WALL MOUNTED THERMOSTAT - GWMT1 WARNING: Installation must be done by a qualified installer familiar with low voltage wiring procedures. WARNING: Do not connect [...]

107304-01D For more information, visit www.desatech.com For more information, visit www.desatech.com 24 REMOVING/REPLACING GLASS DOOR You must remove glass door to install logs, lava rock, and ember material. To remove glass door, you must first remove the front panel on stove body. CAUTION: Do not operate this burner system with a broken glass doo[...]

107304-01D For more information, visit www.desatech.com For more information, visit www.desatech.com 25 25 It is very important to install these logs exactly as instructed in Figures 55 through 58. Do not modify logs. Only use logs supplied with freestanding burner system. Do not use if any log(s) are broken (see Replacement Parts , page 33). 1 . R[...]

107304-01D For more information, visit www.desatech.com For more information, visit www.desatech.com 26 P I L O T O F F P I L O T O N TPTH TP TH H I LO IN OUT TO TURN OFF GAS TO APPLIANCE 1. T urn ON/OFF s witch, located on side of rear co ver , to “OFF”. 2a. Open lower door panel. 2b . If Using Optional Hand-Held Remote: Set selector switch, l[...]

107304-01D For more information, visit www.desatech.com For more information, visit www.desatech.com 27 27 1. After lighting, let pilot flame b urn f or about one minute. T urn gas control knob on the contr ol v alve to ON position. T urn variable contr ol knob anywhere between HI and LO. Slide the selector switch to the REMO TE position. Note: The[...]

107304-01D For more information, visit www.desatech.com For more information, visit www.desatech.com 28 INSPECTING BURNERS Check pilot flame pattern and burner flame patterns often. PILOT ASSEMBLY The pilot assembly is factory preset for the proper flame height. Alterations may have occurred during shipping and handling. Call a qualified service pe[...]

107304-01D For more information, visit www.desatech.com For more information, visit www.desatech.com 29 29 CLEANING AND MAINTENANCE WARNING: Turn off burner system and let cool before cleaning. CAUTION: You must keep control areas, burners, and circulating air passageways of burner system and stove clean. Inspect these areas of burner sys- tem and [...]

107304-01D For more information, visit www.desatech.com For more information, visit www.desatech.com 30 TROUBLESHOOTING Note: All troubleshooting items are listed in order of operation. WARNING: Turn off burner system and let cool before servicing. Only a qualified service person should ser- vice and repair burner system or stove. CAUTION: Never us[...]

107304-01D For more information, visit www.desatech.com For more information, visit www.desatech.com 31 31 OBSERVED PROBLEM Burner does not light after pilot is lit Delayed ignition burner Burner backfiring during combustion Slight smoke or odor during initial operation Burner system produces a whistling noise when burner is lit Glass soots Burner [...]

107304-01D For more information, visit www.desatech.com For more information, visit www.desatech.com 32 TROUBLESHOOTING Continued WARNING: If you smell gas • Shut off gas supply. • Do not try to light any appliance. • Do not touch any electrical switch; do not use any phone in your building. • Immediately call your gas supplier from a neigh[...]

107304-01D For more information, visit www.desatech.com For more information, visit www.desatech.com 33 33 Figure 65 - Blower Wiring Diagram for Thermostat-Controlled Models WIRING DIAGRAM CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after [...]

107304-01D For more information, visit www.desatech.com For more information, visit www.desatech.com 34 TPTH TPTH TP TP TH TH 24 4 19 20 21 23 26-1 26-4 26-2 26-3 29 24 4 25 4 1 28 28 4 7 8 9 18 10 11 13 12 15 16 17 22 4 2 3 6 22 27 14 4 5 ILLUSTRA TED P AR TS BREAKDOWN SDVBNC SDVBPC ILLUSTRATED PARTS BREAKDOWN Models SDVBNC and SDVBPC[...]

107304-01D For more information, visit www.desatech.com For more information, visit www.desatech.com 35 35 P ARTS LIST This list contains replaceable parts used in your burner system. When ordering parts, follow the instructions listed under Replace- ment Parts on page 33 of this manual. PARTS LIST Models SDVBNC and SDVBPC KEY SDVBNC NO. SDVBPC DES[...]

107304-01D For more information, visit www.desatech.com For more information, visit www.desatech.com 36 ILLUSTRA TED P AR TS BREAKDOWN AMITY ™ STOVE CHASSIS SCIVFC(*) SERIES PSCIVFC(*) SERIES (* Indicates Color Suffix Designation) 2 5 8 7-4 6 5 5 7-1 7-2 5 4 7-3 1R 1C 1L 3 ILLUSTRATED PARTS BREAKDOWN Model(s) (P)SCIVFC Series[...]

107304-01D For more information, visit www.desatech.com For more information, visit www.desatech.com 37 37 P ARTS LIST AMITY ™ STOVE CHASSIS SCIVFC(*) SERIES PSCIVFC(*) SERIES (* Indicates Color Suffix Designation) This list contains replaceable parts used in your stove. When ordering parts, follow the instructions listed under Replacement Parts [...]

107304-01D For more information, visit www.desatech.com For more information, visit www.desatech.com 38 ACCESSORIES Purchase these stove and burner system accessories from your local dealer. If they can not supply these accessories, call DESA’s Sales Department at 1-866-672-6040 for information. You can also write to the address listed on the bac[...]

107304-01D For more information, visit www.desatech.com For more information, visit www.desatech.com 39 39 1. Where will the product be used? ❍ Living/F amily Room ❍ Office/W arehouse ❍ Utility Shed/Outbuilding ❍ Garage ❍ Bedroom ❍ Bathroom ❍ Other 2. If y ou bought this product yourself , did you plan to purchase this type of product[...]

107304-01D For more information, visit www.desatech.com For more information, visit www.desatech.com 40 2701 Industrial Drive P.O. Box 90004 Bowling Green, KY 42102-9004 Postage Required T APE T APE[...]

107304-01D For more information, visit www.desatech.com For more information, visit www.desatech.com 41 41 NOTES _______________________________________________________________________________________________ _______________________________________________________________________________________________ _____________________________________________[...]

107304-01D For more information, visit www.desatech.com For more information, visit www.desatech.com 42 W ARRANTY INFORMA TION DESA LIMITED WARRANTY DIRECT-VENT BURNER SYSTEM AND AMITY ™ STOVE CHASSIS DESA warrants this product to be free from defects in materials and components for four (4) years from the date of first purchase, provided that th[...]