Dodge 2009 Challenger manual

2009 CHALL ENGER CHAL LENGER Chrysler LL C 81-226-0916 Second Edition Printed in U.S.A. OWNER ’S MANU AL 2009 147914 Dodge LC22 Challenger.indd 1 9/8/08 3:39:42 PM[...]

VEHICLES SOLD IN CANADA W ith r espect to any V ehicles Sold in Canada, the name Chrysler LLC shall be deemed to be deleted and the name Chrysler Canada Inc. used in substitution therefor . DRIVING AND ALCOHOL Drunken driving is one of the most fr equent causes of accidents. Y our driving ability can be seriously impaired with blood alcohol levels [...]

T ABLE OF CONTENTS SECTION P AGE 1 INTRODUCTION ............................................................ 3 2 THINGS TO KNOW BEFORE ST AR TING YOUR VEHICLE .............................. 9 3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE ............................. 7 1 4 UNDERST ANDING YOUR INSTRUMENT P ANEL .................................. 1 [...]

[...]

INTRODUCTION CONTENTS 䡵 Introduction ........................... 4 䡵 How T o Use This Manual .................. 4 䡵 W arnings And Cautions ................... 6 䡵 V ehicle Identification Number .............. 6 䡵 V ehicle Modifications/Alterations ............ 7 1 3[...]

INTRODUCTION Congratulations on selecting your new Chrysler LLC vehicle. Be assured that it r epresents pr ecision workman- ship, distinctive styling, and high quality - all essentials that are traditional to our vehicles. This Owner’s Manual has been prepar ed with the assis- tance of service and engineering specialists to acquaint you with the [...]

1 INTRODUCTION 5[...]

W ARNINGS AND CAUTIONS This Owner’s Manual contains W ARNINGS against op- erating procedur es that could result in an accident or bodily injury . It also contains CAUTIONS against proce- dures that could r esult in damage to your vehicle. If you do not read this entir e manual, you may miss important information. Observe all W arnings and Caution[...]

VEHICLE MODIFICA TIONS/AL TERA TIONS W ARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death. 1 INTRODUCTION 7[...]

[...]

THINGS T O KNOW BEFORE ST ARTING YOUR VEHICLE CONTENTS 䡵 A W ord About Y our Keys ................. 1 2 ▫ W ireless Ignition Node (WIN) ............ 1 2 ▫ FOB W ith Integrated Key ............... 1 3 ▫ Ignition Key Removal .................. 1 3 ▫ Key-In-Ignition Reminder ............... 1 4 䡵 Sentry Key 威 .......................... 1[...]

▫ T o Open The T runk .................... 2 3 ▫ Using The Panic Alarm ................. 2 3 ▫ Programming Additional T ransmitters ...... 2 4 ▫ T ransmitter Battery Service .............. 2 4 ▫ General Information ................... 2 5 䡵 Remote Starting System .................. 2 6 ▫ How T o Use Remote Start ............... 2 6 ?[...]

▫ Event Data Recorder (EDR) .............. 5 5 ▫ Child Restraint ....................... 5 7 䡵 Engine Break-In Recommendations .......... 6 6 䡵 Safety T ips ........................... 6 7 ▫ T ransporting Passengers ................ 6 7 ▫ Exhaust Gas ......................... 6 7 ▫ Safety Checks Y ou Should Make Inside The V e h i c l[...]

A WORD ABOUT YOUR KEYS Y our vehicle uses a keyless ignition system. This system consists of a Fob and a W ireless Ignition Node (WIN) with an integral ignition switch. Y ou can insert the double-sided integrated key into the ignition switch with either side up. Keyless Go Feature This vehicle may be equipped with the Keyless Go feature, for mor e [...]

Fob With Integrated Key The Fob operates the ignition switch. It also contains the Remote Keyless Entry (RKE) transmitter and an emer- gency key , which stores in the rear of the Fob. The emergency key allows for entry into the vehicle should the battery in the vehicle or the Fob go dead. The emergency key is also for locking the glove box. Y ou ca[...]

NOTE: The power window switches, radio, power sunroof (if equipped), and ignition-power ed power out- lets will remain active for up to 60 minutes after the ignition switch is turned to the LOCK position. Opening either door will cancel this feature. The time for this feature is pr ogrammable. Refer to “Delay Power Off to Accessories Until Exit,?[...]

is automatic, regar dless of whether the vehicle is locked or unlocked. The system uses the factory-mated Remote Keyless Entry (RKE) transmitter with integrated key and W ireless Igni- tion Node (WIN) to prevent unauthorized vehicle opera- tion. Therefor e, only RKE transmitters that are pr o- grammed to the vehicle can be used to start and operate[...]

All of the RKE transmitters provided with your new vehicle have been programmed to the vehicle electr onics. Replacement Keys NOTE: Only RKE transmitters that are pr ogrammed to the vehicle electronics can be used to start and operate the vehicle. Once a transmitter is programmed to a vehicle, it cannot be programmed to any other vehicle. CAUTION! [...]

2. Insert the second valid integrated key and turn the ignition switch to the ON position within 15 seconds. After 10 seconds, a chime will sound and the V ehicle Security Light will begin to flash. T urn the ignition switch to the LOCK position and remove the second key . 3. Insert a blank integrated key into the ignition switch and turn the ignit[...]

VEHICLE SECURITY ALARM The V ehicle Security Alarm monitors the vehicle doors for unauthorized entry and the ignition switch for unau- thorized operation. If something triggers the alarm, the V ehicle Security Alarm will pr ovide the following au- dible and visible signals: the horn will pulse, the head- lights, park lamps and/or turn signals will [...]

• The V ehicle Security Alarm r emains armed during trunk entry . Pressing the TRUNK button will not disarm the V ehicle Security Alarm. If someone enters the vehicle through the tr unk, and opens any door , the alarm will sound. • When the V ehicle Security Alarm is armed, the interior power door lock switches will not unlock the doors. The V [...]

NOTE: • None of the courtesy lights will operate if the dimmer control is in the “defeat” position (extr eme downward position), unless the overhead map/r eading lights are turned on manually . REMOTE KEYLESS ENTR Y (RKE) The Remote Keyless Entry (RKE) allows you to lock or unlock the doors, open the trunk, or activate the Panic Alarm from di[...]

Remote Key Unlock, Driver Door/All Doors First This feature lets you pr ogram the system to unlock either the driver’s door or both doors on the first press of the UNLOCK button on the transmitter . Refer to “Remote Key Unlock,” under “Personal Settings (Customer- Programmable Featur es),” under “Electronic V ehicle In- formation Center[...]

• When not using the EVIC, perform the following steps: 1. Pr ess and hold the UNLOCK button on a programmed transmitter for at least 4 seconds, but no longer than 10 seconds. Then, press and hold the LOCK button while still holding the UNLOCK button. 2. Release both buttons at the same time. 3. T est the feature while outside of the vehicle by p[...]

turned on or turned off. Refer to “Sound Horn with Remote Key Lock,” under “Personal Settings (Customer- Programmable Featur es),” under “Electronic V ehicle In- formation Center (EVIC)” in Section 4. • When not using the EVIC, perform the following steps: 1. Pr ess the LOCK button on a programmed transmitter for at least 4 seconds, b[...]

second and release. When the Panic Alarm is on, the headlights and park lights will flash, the horn will pulse on and off, and the interior lights will turn on. The Panic Alarm will stay on for three minutes unless you turn it off by either pr essing the P ANIC button a second time or drive the vehicle at a speed of 5 mph (24 km/h) or greater . NOT[...]

A void touching the new battery with your fingers. Skin oils may cause battery deterioration. If you touch a battery , clean it with rubbing alcohol. 3. T o reassemble the RKE transmitter case, snap the two halves of the case together . Make sure ther e is an even “gap” between the two halves. If equipped, install and tighten the screw until sn[...]

REMOTE ST ARTING SYSTEM This system uses the Remote Keyless Entry (RKE) transmitter to start the engine conve- niently from outside the vehicle while still maintaining security . The system has a range of 328 ft (100 m). NOTE: The vehicle must be equipped with an auto- matic transmission to be equipped with Remote Start. How T o Use Remote Start Al[...]

T o Enter Remote Start Mode Press and r elease the REMOTE ST AR T button on the RKE transmitter twice, within five sec- onds. The parking lights will flash and the horn will chirp twice (if programmed). Then, the engine will start and the vehicle will remain in the Remote Start mode for a 15-minute cycle. NOTE: • If an engine fault is present the[...]

equipped). Then, prior to the end of the 15 minute cycle, press and r elease the ST AR T/STOP button. If the ST AR T/STOP button is not present, insert the key into the ignition switch and turn the switch to the ON position. NOTE: • For vehicles not equipped with Keyless Go feature, the ignition switch must be in the ON position in order to drive[...]

If the door lock plunger is down when you shut the door , the door will lock. Therefor e, make sure the key is not inside the vehicle before closing the door . W ARNING! • For personal security and safety in the event of an accident, lock the vehicle doors before you drive as well as when you park and leave the vehicle. • When leaving the vehic[...]

locking the key in the vehicle. Removing the key or closing the door will allow the locks to operate. If a door is open, the key is in the ignition, and the ignition is in the LOCK or ACC position, a chime will sound as a reminder to remove the key . Automatic Door Locks The doors will lock automatically if all of the following conditions are met: [...]

Automatic Unlock Doors on Exit Programming The Automatic Unlock Doors On Exit featur e can be enabled or disabled. Refer to “Unlock Doors Automati- cally on Exit,” under “Personal Settings (Customer- Programmable Featur es),” under “Electronic V ehicle In- formation Center (EVIC)” in Section 4. • When not using the EVIC, perform the f[...]

WINDOWS Power Windows The window controls on the driver’s door contr ol both of the door windows. There is a single window contr ol on the passenger’s door trim panel that operates the window on the passenger’s door . The window controls will operate only when the ignition switch is in the ON or ACC position. NOTE: • The door window will lo[...]

W ARNING! Never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches. Such entrapment may result in serious injury or death. AUTO-Down Feature The driver’s door power window switch and passenger door power window [...]

TRUNK LOCK AND RELEASE The trunk lid can be r eleased from inside the vehicle by pressing the T runk Release button. The button is located on the instrument panel to the left of the steering wheel. NOTE: The transmission must be in P ARK before the button will operate. If equipped with a manual transmis- sion, the vehicle speed must be under 5 mph [...]

TRUNK SAFETY W ARNING W ARNING! Do not allow children to have access to the trunk, either by climbing into the trunk from outside, or through the inside of the vehicle. Always close the trunk lid when your vehicle is unattended. Once in the trunk, young children may not be able to escape, even if they entered through the rear seat. If trapped in th[...]

OCCUP ANT RESTRAINTS Some of the most important safety features in your vehicle are the r estraint systems. These include the front and rear seat belts for the driver and all passengers, the front airbags for both the driver and fr ont passenger , and the supplemental side curtain airbags for the driver and passengers seated next to a window . If y[...]

ejection and the risk of injury caused by striking the inside of the vehicle. Everyone in a motor vehicle should be belted at all times. Lap/Shoulder Belts All seating positions in your vehicle are equipped with lap/shoulder belts. The belt webbing retractor is designed to lock during very sudden stops or impacts. This feature allows the shoulder p[...]

W ARNING! (Continued) • W earing your belt in the wrong place could make your injuries in a collision much worse. Y ou might suffer internal injuries, or you could even slide out of part of the belt. Follow these instructions to wear your seat belt safely and to keep your pas- sengers safe, too. • T wo people should never be belted into a singl[...]

3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” W ARNING! • A belt that is buckled into the wrong buckle will not protect you properly . The lap portion could ride too high on your body , possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt[...]

W ARNING! (Continued) • A shoulder belt placed behind you will not protect you from injury during a collision. Y ou are more likely to hit your head in a collision if you do not wear your shoulder belt. The lap and shoulder belt are meant to be used together . 4. Position the lap belt acr oss your thighs, below your abdomen. T o remove slack in t[...]

6. T o release the belt, push the r ed button on the buckle. The belt will automatically retract to its stowed position. If necessary , slide the latch plate down the webbing to allow the belt to retract fully . W ARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically , ch[...]

2. At about 6 to 12 in (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180 degrees to cr eate a fold that begins immediately above the latch plate. 3. Slide the latch plate upwar d over the folded webbing. The folded webbing must enter the slot at the top of the latch plate. 4. Continue to slide the latch plate up until it cle[...]

chime and flash the Seat Belt Reminder Light for 96 sec- onds or until the driver’s seat belt is buckled. The BeltAlert 威 will be reactivated if the driver’s seat belt is unbuckled for more than 10 seconds and the vehicle speed is greater than 5 mph (8 km/h). BeltAlert 威 Programming The BeltAlert 威 can be enabled or disabled by your autho[...]

NOTE: When the BeltAlert 威 is deactivated, the Seat Belt Reminder Light will continue to illuminate as long as the driver’s seat belt is unbuckled. Automatic Locking Mode — If Equipped In this mode, the shoulder belt is automatically pre- locked. However , the belt will still retract to r emove slack in the shoulder belt. Use the Automatic Lo[...]

Seat Belt Extender If a seat belt is too short even when fully extended your authorized dealer can provide you with a seat belt extender . This extender should be used only if the existing belt is not long enough. When it is not requir ed, remove the extender and stor e it. W ARNING! Using a seat belt extender when not needed can increase the risk [...]

NOTE: The front airbags ar e certified to the Federal regulations that allow less for ceful deployment. The front airbags have a multistage inflator design. This allows the airbag to have differ ent rates of inflation that are based on collision severity . W ARNING! • Do not put anything on or around the front airbag covers or attempt to open the[...]

W ARNING! • Do not stack luggage or other cargo up high enough to block the location of the side curtain airbag. The area where the side curtain airbag is located should remain free from any obstructions. • Do not have any accessory items installed which will alter the roof, including adding a sunroof to your vehicle. Do not add roof racks that[...]

W ARNING! Infants in rear-facing child restraints should NEVER ride in the front seat of a vehicle with a passenger front airbag. An airbag deployment could cause severe injury or death to infants in that position. 2. Childr en who are not big enough to wear the vehicle seat belt properly should be secur ed in the rear seat in child restraints or b[...]

W ARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly . In some collisions, the airbags won’t deploy at all. Always wear your seat belts even though you have airbags. • Being too close to the steering wheel or instrument panel during airbag dep[...]

• Knee Impact Bolsters • Front Acceleration Sensors • Driver and Front Passenger Seat Belt Pr etensioners How the Airbag System W orks • The Occupant Restraint Controller (ORC) determines if a frontal collision is sever e enough to requir e the airbags to inflate. The front airbag inflators ar e de- signed to provide dif ferent rates of air[...]

W ARNING! Ignoring the Airbag W arning Light in your instru- ment panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away . • The Driver and Front Passenger Airbag/Inflator Units are l[...]

inflating side curtain airbag pushes the outside edge of the headliner out of the way and covers the window . The airbag inflates in about 30 milliseconds (about one-quarter of the time that it takes to blink your eyes) with enough force to injur e you if you are not belted and seated properly , or if items are positioned in the area wher e the sid[...]

throat irritation, move to fr esh air . If the irritation continues, see your doctor . If these particles settle on your clothing, follow the garment manufacturer’s in- structions for cleaning. • It is not advisable to drive your vehicle after the airbags have been deployed. If you are involved in another collision, the airbags will not be in p[...]

Maintaining Y our Airbag System W ARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. Y ou could be injured because the airbags are not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper passen[...]

Event Data Recorder (EDR) In the event of an accident, your vehicle is designed to recor d up to five seconds of specific vehicle data param- eters (see the following list) in an event data recor der prior to the moment of airbag deployment, or near deployment, and up to a quarter second of high-speed deceleration data during and/or after airbag de[...]

upon request. General data that does not identify par - ticular vehicles or crashes may be released for incorpo- ration in aggregate crash databases, such as those main- tained by the U.S. government and various states. Data of a potentially sensitive nature, such as would identify a particular driver , vehicle, or crash, will be treated confi- den[...]

• T raction/stability control status • T ire Pressur e Monitoring System status (if equipped) Child Restraint Everyone in your vehicle needs to be buckled up all the time, including babies and children. Every state in the United States and all Canadian provinces r equire that small children ride in pr oper restraint systems. This is the law , a[...]

Infants and Child Restraints • Safety experts recommend that childr en ride rearwar d-facing in the vehicle until they are at least one year old and weigh at least 20 lbs (9 kg). T wo types of child restraints can be used r earward-facing, infant carriers and convertible child seats. • The infant carrier is only used rearwar d-facing in the veh[...]

The belt-positioning booster seat is for children weighing more than 40 lbs (18 kg), but who ar e still too small to fit the vehicle’s seat belts properly . If the child cannot sit with knees bent over the vehicle’s seat cushion while the child’s back is against the seatback, they should use a belt-positioning booster seat. The child and belt[...]

W ARNING! (Continued) • A rearward-facing child restraint should only be used in a rear seat. A rearward-facing child re- straint in the front seat may be struck by a deploy- ing passenger airbag, which may cause severe or fatal injury to the infant. Here are some tips on getting the most out of your child restraint: • Before buying any r estra[...]

the child restraint using lower anchorages and upper tether straps from the child r estraint to the vehicle structur e. LA TCH-compatible child restraint systems ar e now avail- able. However , because the lower anchorages are to be introduced over a period of years, child r estraint systems having attachments for those anchorages will continue to [...]

Installing the LA TCH-Compatible Child Restraint System W e urge you to follow the manufactur er’s directions carefully when installing your child r estraint. Not all child restraint systems will be installed as described her e. Again, carefully follow the installation instr uctions that are pr ovided with the child restraint system. The rear sea[...]

most direct path between the anchor and the child restraint. Finally , tighten all three straps as you push the child restraint r earward and downwar d into the seat, removing slack in the straps accor ding to the child restraint manufactur er’s instructions. NOTE: • Ensure that the tether strap does not slip into the opening between the seatba[...]

restraint so that it is not necessary to use a locking clip. Pulling up on the shoulder portion of the lap/shoulder belt will tighten the belt. The cinching latch plate will keep the belt tight; however , any seat belt system will loosen with time, so check the belt occasionally and pull it tight if necessary . The seat belt must be in the Automati[...]

2. Route the tether strap to provide the most dir ect path for the strap between the anchor and the child seat. 3. Attach the tether strap hook (A) of the child restraint to the anchor (B) and remove slack in the tether strap according to the child r estraint manufacturer’s instruc- tions. NOTE: Ensure that the tether strap does not slip into the[...]

ENGINE BREAK-IN RECOMMENDA TIONS A long break-in period is not requir ed for the drivetrain (engine, transmission, and rear axle) in your new vehicle. Drive moderately during the first 500 mi (800 km). After the initial 60 mi (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. While cruising, brief full-thr ottle acceleration within [...]

SAFETY TIPS T ransporting Passengers NEVER TRANSPOR T P ASSENGERS IN THE CARGO AREA. W ARNING! • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seri- ously injured or killed. • Do not allow people to ride in any area of your vehicle that is no[...]

If you are r equired to drive with the trunk/liftgate open, make sure that all windows ar e closed and the climate control BLOWER switch is set at high speed. DO NOT use the recir culation mode. The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. Whenever a change is noticed in the[...]

Defroster Check operation by selecting the defrost mode and place the blower control on high speed. Y ou should be able to feel the air directed against the windshield. See your authorized dealer for service if your defroster is inoperable. Periodic Safety Checks Y ou Should Make Outside the V ehicle T ires Examine tires for excessive tr ead wear a[...]

[...]

UNDERST ANDING THE FEA TURES OF YOUR VEHICLE CONTENTS 䡵 M i r r o r s .............................. 7 5 ▫ Automatic Dimming Mirror — If Equipped . . . 75 ▫ Outside Mirrors ...................... 7 5 ▫ Outside Mirrors Folding Featur e .......... 7 6 ▫ Power Mirrors ....................... 7 6 ▫ Heated Mirrors — If Equipped .........[...]

䡵 V oice Recognition (VR) System — If Equipped .......................... 1 0 6 ▫ V oice Recognition (VR) System Operation . . . 106 ▫ Commands ........................ 1 0 8 ▫ V o i c e T r a i n i n g ....................... 1 1 1 䡵 Seats ............................... 1 1 1 ▫ Easy Entry Seats ...................... 1 1 1 ▫ Power[...]

䡵 W indshield W ipers And W ashers .......... 1 2 5 ▫ Intermittent W iper System .............. 1 2 5 ▫ Mist Feature ........................ 1 2 6 ▫ W indshield W ashers .................. 1 2 6 ▫ Headlights On W ith W ipers (A vailable W ith Auto Headlights Only) ................ 1 2 6 䡵 T ilt/T elescoping Steering Column .......... 1[...]

䡵 Power Sunroof — If Equipped ............ 1 3 9 ▫ Opening Sunroof — Partially ............ 1 4 0 ▫ Opening Sunroof — Expr ess ............ 1 4 0 ▫ Closing Sunroof — Partially ............. 1 4 0 ▫ Closing Sunroof — Expr ess ............. 1 4 1 ▫ Pinch Protect Featur e ................. 1 4 1 ▫ Pinch Protect Override .......[...]

MIRRORS Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glar e from vehicles behind you. Y ou can turn the feature on or off by pr essing the button at the base of the mirror . A light next to the button will illuminate to indicate when the dimming feature is activated. CAUTION! T o avoid damage to the mirro[...]

W ARNING! V ehicles and other objects seen in the passenger-side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger-side convex mirror could cause you to collide with another vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the passenger-sid[...]

Heated Mirrors — If Equipped These mirrors ar e heated to melt frost or ice. This feature is activated whenever you turn on the r ear window defroster . Refer to “Rear W indow Features” in this section, for further information. V anity Mirrors A vanity mirror is located on the sun visor . T o use the mirror , rotate the sun visor downwar d an[...]

your left hand pull rearwar ds until the sun visor is in the desired position. T o use the extender feature of the sun visor , grab the extender which is located at the rear of the visor and pull rearwar d. uconnect 姞 phone — IF EQUIPPED NOTE: The sales code RER and REU radios contain an integrated uconnect 威 phone. Refer to your “Navigatio[...]

For uconnect 威 customer support, visit the following websites: • www .chrysler .com/uconnect • www .dodge.com/uconnect • www .jeep.com/uconnect • or call 1–877–855–8400 uconnect 威 allows you to transfer calls between the sys- tem and your cellular phone as you enter or exit your vehicle and enables you to mute the system’s micro[...]

The uconnect 威 phone can be used with any Hands-Free Profile certified Bluetooth 威 cellular phone. See the uconnect 威 website for supported phones. If your cellular phone supports a differ ent profile (e.g., Headset Pr ofile) you may not be able to use any uconnect 威 phone features. Refer to your cellular service pr ovider or the phone manu[...]

example, you can use the combined form voice com- mand ⬙ Phonebook New Entry , ⬙ or you can break the combined form command into two voice commands: ⬙ Phonebook ⬙ and ⬙ New Entry . ⬙ Please remember , the uconnect 威 phone works best when you talk in a normal conversational tone, as if speaking to someone sitting a few feet/meters away[...]

• When prompted, after the beep, say ⬙ Pair a Phone ⬙ and follow the audible prompts. • Y ou will be asked to say a four-digit Personal Identi- fication Number (PIN), which you will later need to enter into your cellular phone. Y ou can enter any four-digit PIN. Y ou will not need to remember this PIN after the initial pairing process. • [...]

• The uconnect 威 phone will confirm the phone number and then dial. The number will appear in the display of certain radios. Call by Saying a Name • Press the PHONE button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say “Call. ⬙ • The system will prompt you to say the name of the person you want to call. • Aft[...]

• When prompted, enter the number designation (e.g., ⬙ Home, ⬙⬙ W ork, ⬙⬙ Mobile, ⬙ or ⬙ Pager ⬙ ). This will allow you to store multiple numbers for each phonebook entry , if desired. • When prompted, r ecite the phone number for the phonebook entry that you are adding. After you are finished adding an entry into the phone- boo[...]

• Depending on the maximum number of entries down- loaded, there may be a short delay befor e the latest downloaded names can be used. Until then, if avail- able, the previous downloaded phonebook is available for use. • Only the phonebook of the currently connected cellu- lar phone is accessible. • Only the cellular phone’s phonebook is do[...]

first disconnect or drop the Bluetooth 威 connection to the uconnect 威 phone, and then send the address book entry via Bluetooth 威 . Please see your phone Owner ’s Manual for specific instructions on how to dr op the Bluetooth 威 connection. • If the phonebook entry is longer than 24 characters, it will only use the first 24 characters. E[...]

Delete uconnect 威 Phonebook Entry NOTE: Editing phonebook entries is recommended when the vehicle is not in motion. • Press the PHONE button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Phonebook Delete. ⬙ • After you enter the Phonebook Delete menu, you will then be asked for the name of the entry that you w[...]

• Note that only the phonebook in the current language is deleted. • Automatic downloaded phonebook entries cannot be deleted or edited. List All Names in the uconnect 威 Phonebook • Press the PHONE button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Phonebook List Names. ⬙ • The uconnect 威 phone will pl[...]

Answer or Reject an Incoming Call - Call Currently in Progress If a call is currently in pr ogress and you have another incoming call, you will hear the same network tones for call waiting that you normally hear when using your cellular phone. Press the PHONE button to place the current call on hold and answer the incoming call. NOTE: The uconnect [...]

Three-W ay Calling T o initiate three-way calling, pr ess the VOICE RECOG- NITION button while a call is in progr ess, and make a second phone call, as described under ⬙ Making a Second Call While Current Call is in Pr ogress. ⬙ After the second call has established, press and hold the PHONE button until you hear a double beep, indicating that [...]

• After the ignition key is switched to OFF , a call can continue on the uconnect 威 phone for a certain dura- tion, after which the call is automatically transferred from the uconnect 威 phone to the cellular phone. • An active call is automatically transferred to the cellular phone after the ignition key is switched to OFF . uconnect 姞 ph[...]

If the phone is not reachable and the uconnect 威 phone is operational, you may reach the emer gency number as follows: • Press the PHONE button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Emergency ⬙ and the uconnect 威 phone will instr uct the paired cellular phone to call the emer gency num- ber . This feat[...]

T owing Assistance If you need towing assistance: • Press the PHONE button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ T owing Assistance. ⬙ NOTE: • The towing assistance number dialed is based on the country where the vehicle is pur chased (1-800-528- 2069 for the U.S., 1-877-213-4525 for Canada, 55-14- 3454 [...]

When calling a number with your uconnect 威 phone that normally requir es you to enter in a touch-tone sequence on your cellular phone keypad, you can press the VOICE RECOGNITION button and say the sequence you wish to enter , followed by the word ⬙ Send. ⬙ For example, if requir ed to enter your PIN followed with a pound, (3 7 4 6 #), you can[...]

T urning Confirmation Prompts ON/OFF T urning confirmation prompts of f will stop the system from confirming your choices (e.g., the uconnect 威 phone will not repeat a phone number befor e you dial it). • Press the PHONE button to begin. • After the ⬙ Ready ⬙ prompt and the following beep, say ⬙ Setup Confirmations. ⬙ The uconnect 威[...]

Mute/Un-Mute (Mute OFF) When you mute the uconnect 威 phone, you will still be able to hear the conversation coming from the other party , but the other party will not be able to hear you. In order to mute the uconnect 威 phone: • Press the VOICE RECOGNITION button. • Following the beep, say ⬙ Mute. ⬙ In order to un-mute the uconnect 威 [...]

• The uconnect 威 phone will play the phone names of all paired cellular phones in or der from the highest to the lowest priority . T o “select” or “delete” a paired phone being announced, press the VOICE RECOGNITION button and say “Select” or “Delete.” Also, see the next two sections for an alternate way to “select” or “de[...]

Things Y ou Should Know About Y our uconnect 姞 phone uconnect 威 phone T utorial T o hear a brief tutorial of the system features, pr ess the PHONE button and say “uconnect 威 T utorial.” V oice T raining For users experiencing difficulty with the system r ecog- nizing their voice commands or numbers, the uconnect 威 phone V oice T raining[...]

• Speak normally , without pausing, just as you would speak to a person sitting a few feet/meters away from you. • Make sure that no one other than you is speaking during a voice recognition period. • Performance is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface,[...]

• In a convertible vehicle, system performance may be compromised with the convertible top down. Far End Audio Performance • Audio quality is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, • dry weather conditions, and • operation fro[...]

3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 101[...]

102 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE[...]

3 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE 103[...]

V oice Commands Primary Alternate(s) zero one two three four five six seven eight nine star (*) plus (+) pound (#) add location all V oice Commands Primary Alternate(s) call cancel confirmation prompts continue delete dial download edit emergency English erase all Espanol Francais help home 104 UNDERST ANDING THE FEA TURES OF YOUR VEHICLE[...]

V oice Commands Primary Alternate(s) language list names list phones mobile mute mute off new entry no pager pair a phone phone pairing pairing phonebook phone book previous recor d again redial V oice Commands Primary Alternate(s) return to main menu return or main menu select phone select send set up phone settings or phone set up towing assistan[...]

General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • Changes or modifications not expressly appr oved by the party responsible for compliance could void the user’s authority to operate the equipment. • This device may not cause harmful interf[...]

When you press the VR button, you will hear a beep. The beep is your signal to give a command. NOTE: If you do not say a command within a few seconds, the system will present you with a list of options. If you ever wish to interrupt the system while it lists options, press the VR button, listen for the beep, and say your command. Pressing the VR bu[...]

Commands The V oice Recognition (VR) system understands two types of commands. Universal commands are available at all times. Local commands are available if the supported radio mode is active. Changing the V olume 1. Start a dialogue by pr essing the VR button. 2. Say a command (e.g., “Help”). 3. Use the ON/OFF VOLUME r otary knob to adjust th[...]

Radio FM T o switch to the FM band, say “FM” or “Radio FM”. In this mode, you may say the following commands: • “Frequency” (to change the fr equency) • “Next Station” (to select the next station) • “Previous Station” (to select the pr evious station) • “Radio Menu” (to switch to the radio menu) • “Main Menu” ([...]

Memo T o switch to the voice recor der mode, say “Memo”. In this mode, you may say the following commands: • “New Memo” (to recor d a new memo) — During the recor ding, you may press the VR button to stop recor ding. Y ou proceed by saying one of the following commands: − “Save” (to save the memo) − “Continue” (to continue r[...]

NOTE: Keep in mind that you have to press the VR button first and wait for the beep before speaking the “Barge In” commands. V oice T raining For users experiencing difficulty with the system r ecog- nizing their voice commands or numbers, uconnect 威 phone V oice T raining feature may be used. 1. Pr ess the VR button, say “System Setup” a[...]

Power Seats The power seat switches are on the outboar d side of the front seat cushions. The power seat switch can be moved forward and backwar d as well as up and down to control the position of the seat. The power seatback switch is used to adjust the angle of the seatback. Push forward or rearwar d on the switch to change the position of the se[...]

W ARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked. CAUTION! Do not place any article under a power seat as it may cause damage to the seat control[...]

Lumbar Support This feature allows you to incr ease or decrease the amount of lumbar support. T urn the control lever for - ward to incr ease and rearwar d to decrease the desired amount of lumbar support. Head Restraints Head restraints can r educe the risk of whiplash injury in the event of a rear impact. Adjust the restraint so that the upper ed[...]

Heated Seats The driver seat and front passenger seat ar e heated. The heaters provide the same heat level for both cushion and seatback. The controls for each heater ar e located near the bottom center of the instrument panel. After turning the ignition ON, you can choose from High, Low , or Off heat settings. Amber indicator lights in each switch[...]

W ARNING! • Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury , medication, alcohol use, ex- haustion, or other physical conditions must exer- cise care when using the seat heater . It may cause burns even at low temperatures, especially if used for long periods. • Do not plac[...]

W ARNING! • Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position, the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury . • The cargo area in the rear of the vehicle (with the rear seatbacks in the loc[...]

2. Move to the outside of the vehicle and push the safety catch to the left. The safety catch is located under the center front edge of the hood. CAUTION! T o prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approxi- mately 6 in (15 cm), and then drop it. This should secure both latches. Never drive your ve[...]

LIGHTS Headlight Switch The headlight switch is located on the left side of the instrument panel. This switch contr ols the operation of the headlights, parking lights, instrument panel lights, instrument panel light dimming, interior lights and fog lights. Rotate the headlight switch clockwise to the first detent for parking light and instrument p[...]

Automatic Headlights — If Equipped This system automatically turns the headlights on or off according to ambient light levels. T o turn the system on, rotate the headlight switch counter clockwise to the AUTO (A) position. When the system is on, the headlight time delay feature is also on. This means the headlights will stay on for up to 90 secon[...]

If you turn the headlights, parking lights, or ignition switch ON again, the system will cancel the delay . If you turn the headlights off befor e the ignition, they will turn off in the normal manner . NOTE: The lights must be turned off within 45 seconds of turning the ignition OFF to activate this feature. The Headlight delay time is programmabl[...]

Multifunction Lever The multifunction lever controls the operation of the turn signals, headlight beam selection, and passing lights. The multifunction lever is located on the left side of the steering column. T urn Signals Move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation o[...]

High Beam/Low Beam Select Switch Push the multifunction lever away from you to switch the headlights to high beam. Pull the multifunction lever toward you to switch the headlights back to low beam. Flash-to-Pass Y ou can signal another vehicle with your headlights by lightly pulling the multifunction lever toward you. This will turn on the high bea[...]

because a door is open. This includes the glove box light, but not the trunk light. T o restor e interior light operation, either turn the ignition switch ON or cycle the light switch. Dimmer Control The dimmer control is part of the headlight switch and is located on the left side of the instrument panel. W ith the parking lights or headlights on,[...]

WINDSHIELD WIPERS AND W ASHERS The multifunction lever operates the windshield wipers and washer when the ignition switch is in the ON position. The multifunction lever is lo- cated on the left side of the steering column. Rotate the end of the multifunction lever to the first detent past the intermittent settings for low-speed wiper operation, or [...]

regulate the wipe interval fr om a minimum of one cycle every second to a maximum of approximately 23 seconds between cycles. W ARNING! Sudden loss of visibility through the windshield could lead to an accident. Y ou might not see other vehicles or other obstacles. T o avoid sudden icing of the windshield during freezing weather , warm the windshie[...]

position. In addition, the headlights will turn off when the wipers are turned of f if they were turned on by this feature. The Headlights On with W ipers feature can be enabled or disabled. Refer to ”Headlights On with W ipers,” under “Personal Settings (Customer-Pr ogrammable Features)” under “Electronic V ehicle Information Center (EVI[...]

outward or push it inwar d as desired. T o lock the steering column in position, push the control handle inwar d until fully engaged. W ARNING! Do not adjust the steering wheel while driving. The telescoping adjustment must be locked while driv- ing. Adjusting the steering wheel while driving or driving without the telescoping adjustment locked cou[...]

simultaneously . If this occurs, the Electronic Speed Con- trol System can be r eactivated by pushing the Electronic Speed Control ON/OFF button and r esetting the desired vehicle set speed. T o Activate Push and release the ON/OFF button located on the end of the Electronic Speed Contr ol lever . The indicator light in the instrument cluster will [...]

• Electronic Speed Contr ol may not engage if a differ ent size tire is installed on one wheel, such as the compact spare tir e. T o Deactivate The system will disable Electronic Speed Contr ol without erasing the memory if you: • Softly tap the brake pedal. • Press the brake pedal, or pr ess the clutch pedal to the floor (manual transmission[...]

T apping the lever to SET DECEL once will result in a 1 mph (1.6 km/h) speed decrease. Each time the lever is tapped, speed decreases. T o Accelerate For Passing Press the accelerator as you would normally . When the pedal is released, the vehicle will r eturn to the set speed. Using Electronic Speed Control on Hills NOTE: The Electronic Speed Cont[...]

OVERHEAD CONSOLE The overhead console contains courtesy/r eading lights and sunglass storage. Universal Garage Door Opener (HomeLink 威 ) button and a power sunroof switch may also be included, if equipped. Courtesy/Reading Lights At the forward end of the console ar e two courtesy/ reading lights. Press the lens to turn on the light. Pr ess it a [...]

GARAGE DOOR OPENER — IF EQUIPPED HomeLink 威 replaces up to thr ee remote contr ols (hand- held transmitters) that operate devices such as garage door openers, motorized gates, lighting, or home security systems. The HomeLink 威 unit operates off your vehicle’s battery . The HomeLink 威 buttons are located in the over head console, and conta[...]

W ARNING! • Y our motorized door or gate will open and close while you are training the Universal T ransceiver . Do not train the transceiver if people or pets are in the path of the door or gate. Only use this trans- ceiver with a garage door opener that has a “stop and reverse” feature as required by federal safety standards. This includes [...]

2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) from the HomeLink 威 buttons while keeping the EVIC display in view . For optimal training, point the battery end of the hand- held transmitter away from the HomeLink 威 . 3. Simultaneously , press and hold both the chosen HomeLink 威 button and the hand-held transmitter button until the E[...]

This can usually be found where the hanging antenna wire is attached to the garage door opener motor (it is NOT the button normally used to open and close the door). 6. Firmly pr ess and release the “learn” or “training” button. The name and color of the button may vary by manufacturer . NOTE: There ar e 30 seconds in which to initiate the [...]

Gate Operator/Canadian Programming Canadian radio-frequency laws r equire transmitter sig- nals to “time-out” (or quit) after several seconds of transmission – which may not be long enough for HomeLink 威 to pick up the signal during programming. Similar to this Canadian law , some U.S. gate operators are designed to “time-out” in the sa[...]

Reprogramming A Single HomeLink 姞 Button T o repr ogram a channel that has been previously trained, follow these steps: 1. T urn the ignition switch to the ON/RUN position. 2. Pr ess and hold the desired HomeLink 威 button for 20 seconds until the EVIC display states “CHANNEL # TRAINING.” Do not release the button. 3. W ithout releasing the [...]

General Information This device complies with FCC rules Part 15 and Industry Canada RSS-210. Operation is subject to the following two conditions: 1. This device may not cause harmful interfer ence 2. This device must accept any interfer ence that may be received including interfer ence that may cause undesired operation NOTE: The transmitter has b[...]

W ARNING! • Never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. • In an accident, there is a greater risk of being thrown from a vehicle with[...]

the switch in the forward position, the sunr oof will close fully and then stop automatically . Release the switch once the sunroof stops moving. Closing Sunroof — Express Press the switch forwar d and release, and the sunr oof will close automatically from any position. The sunr oof will close fully and stop automatically . This is called Expres[...]

NOTE: The sunshade cannot be closed if the sunroof is open. Wind Buffeting W ind buffeting can be described as the perception of pressur e on the ears or a helicopter-type sound in the ears. Y our vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occu[...]

The center console power outlet is powered dir ectly from the battery (power available at all times). Items plugged into this power outlet may discharge the battery and/or prevent the engine fr om starting. W ARNING! T o avoid serious injury or death: • Do not use a three-prong adapter . • Do not insert any objects into the receptacles. • Do [...]

CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery even when not in use (i.e., cellular phones, etc.). Eventually , if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting. • Accessories that draw higher power (i.e., co[...]

Illuminated Front Cupholders — If Equipped The front cupholders ar e illuminated with LEDs. They are turned on with the headlights or parking lights. Refer to “Interior Lights” under “Lights” in Section 3. Rear Cupholders The rear seat cupholders ar e located in the center armrest between the rear seats. The cupholders ar e positioned for[...]

CONSOLE FEA TURES Sliding Center Console Armrest The center console armrest slides forwar d with three detents to provide flexibility for comfort, cupholder use, and shifting ease. Console Storage The center console has a storage compartment located underneath the armrest, and also contains a 12-V olt power outlet, a molded-in coin holder (designed[...]

REAR WINDOW FEA TURES Rear Window Defroster The rear window defr oster button is located on the climate control (Mode) knob. Pr ess this button to turn on the rear window defr oster and the heated outside mirrors (if equipped). An indicator in the button will illuminate when the rear window defr oster is on. The rear window defr oster automatically[...]

CAUTION! Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear window . Do not use abrasive window cleaners on the interior surface of the window . Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Labels can be peeled off after soaking with w[...]

UNDERST ANDING YOUR INSTRUMENT P ANEL CONTENTS 䡵 Instrument Panel Featur es ............... 1 5 3 䡵 Instrument Cluster – Base ............... 1 5 4 䡵 Instrument Cluster – Pr emium ............ 1 5 5 䡵 Instrument Cluster Description ............ 1 5 6 䡵 Electronic V ehicle Information Center (EVIC) . . 168 ▫ Electronic V ehicle Infor[...]

▫ Operating Instructions - Radio Mode ...... 1 8 2 ▫ Operation Instructions - (Disc Mode For CD And MP3/WMA Audio Play) ............ 1 8 7 ▫ Notes On Playing MP3/WMA Files ....... 1 8 9 ▫ List Button (Disc Mode For M P 3 / W M A P l a y ) .................... 1 9 1 ▫ Info Button (Disc Mode For MP3/WMA P l a y ) ...........................[...]

▫ Info Button (CD Mode For MP3 Play) ...... 2 1 6 䡵 Universal Consumer Interface (UCI) — If Equipped .......................... 2 1 7 ▫ Connecting The iPod 威 ................. 2 1 8 ▫ Using This Feature ................... 2 1 8 ▫ Controlling The iPod 威 Using Radio Buttons ....................... 2 1 8 ▫ P l a y M o d e ..........[...]

䡵 Climate Controls ...................... 2 3 0 ▫ Manual Air Conditioning And Heating System ............................ 2 3 0 ▫ Operating T ips ...................... 2 3 5 152 UNDERST ANDING YOUR INSTRUMENT P ANEL[...]

INSTRUMENT P ANEL FEA TURES 1 — Air Outlets 5 — Heated Seat Switch 9 — Ignition Switch 2 — Instrument Cluster 6 — ESP OFF Switch 10 — T runk Release Button 3 — Glove Compartment 7 — Hazard W arning Switch 1 1 — Headlight Switch 4 — Radio 8 — Climate Control 4 UNDERST ANDING YOUR INSTRUMENT P ANEL 153[...]

INSTRUMENT CLUSTER – BASE 154 UNDERST ANDING YOUR INSTRUMENT P ANEL[...]

INSTRUMENT CLUSTER – PREMIUM 4 UNDERST ANDING YOUR INSTRUMENT P ANEL 155[...]

INSTRUMENT CLUSTER DESCRIPTION 1. Fuel Gauge The pointer shows the level of fuel in the fuel tank when the ignition switch is in the ON position. 2. T rip Odometer Button Premium Cluster Press this button to change the display fr om odometer to either of two trip odometer settings. The letter “A” or “B” will appear when in the trip odometer[...]

6. Char ging System W arning Light This light shows the status of the electrical charg- ing system. The light should turn on when the ignition switch is first turned ON and remain on briefly as a bulb check. If the light stays on or turns on while driving, turn off some of the vehicle’s non-essential electrical devices (i.e., radio) or slightly i[...]

CAUTION! Driving with a hot engine cooling system could damage your vehicle. If the temperature gauge reads “H,” pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on the “H,” and you hear a chime, turn the engine OFF immediately and[...]

1 1. Engine T emperature W arning Light This light will turn on and a single chime will sound to warn of an overheated engine condition. When this light turns on, the engine temperature is critically hot. If the light turns on while driving, safely pull over and stop the vehicle. The vehicle should be turned OFF immediately and serviced as soon as [...]

14. Oil Pr essure W arning Light This light indicates low engine oil pressur e. The light should turn on momentarily when the engine is started. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound for four minutes when this light turns on. Do not operate the vehicle until the cause i[...]

19. Odometer / Electr onic V ehicle Information Center (EVIC) Display Area The odometer shows the total distance the vehicle has been driven. The trip odometer shows individual trip mileage. Refer to “T rip Odometer Button” for additional information. NOTE: U.S. Federal regulations r equire upon transfer of vehicle ownership, the seller certify[...]

display area. T ighten the fuel filler cap properly and press the TRIP ODOMETER button to turn off the message. If the problem continues, the message will appear the next time the vehicle is started. A loose, improperly installed, or damaged fuel filler cap may also turn on the Malfunction Indicator Light (MIL). Lo tirE When the appropriate conditi[...]

20. Brake W arning Light This light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on, it may indicate that the parking brake is applied, that the brake fluid level is low , or that there is a pr oblem with the anti-lock brake system reservoir . If the light remains on when the [...]

W ARNING! Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. Y ou could have an accident. Have the vehicle checked immediately . V ehicles equipped with the Anti-Lock Brake System (ABS), are also equipped with Electr onic Brake Force Distribution (EBD). In t[...]

As an added safety feature, your vehicle has been equipped with a T ire Pressur e Monitoring System (TPMS) that illuminates a low tire pr essure telltale when one or more of your tir es is significantly under-inflated. Accordingly , when the low tire pr essure telltale illumi- nates, you should stop and check your tires as soon as possible, and inf[...]

CAUTION! The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system opera- tion or sensor damage may result when using re- placement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause se[...]

the key is in the ON position before engine start. If the MIL does not come on when turning the key from LOCK to ON, have the condition checked promptly . Certain conditions such as a loose or missing gas cap, poor fuel quality , etc., may illuminate the MIL after engine start. The vehicle should be serviced if the MIL stays on through several of y[...]

ELECTRONIC VEHICLE INFORMA TION CENTER (EVIC) The Electronic V ehicle Information Center (EVIC) fea- tures a driver -interactive display which is located in the instrument cluster . This system conveniently allows the driver to select a variety of useful information by pressing the switches mounted on the steering wheel. The EVIC consists of the fo[...]

• Surround Sound Modes (If Equipped with Driver - Selectable Surround [DSS]) The system allows the driver to select information by pressing the following buttons mounted on the steering wheel. MENU Button Press and r elease the MENU button and the mode displayed will change between T rip Functions, Performance Pages, uconnect™ gps (If Equipped)[...]

Electronic V ehicle Information Center (EVIC) Displays When the appropriate conditions exist, the EVIC displays the following messages. • T urn Signal On (with a continuous warning chime if the vehicle is driven more than 1 mile [1.6 km] with either turn signal on) • Left Front T urn Signal Light Out (with a single chime) • Left Rear T urn Si[...]

• Right Front Low Pr essure (with a single chime) • Right Rear Low Pressur e (with a single chime) • Check TPM System (with a single chime) • ESP Of f – Electronic Stability Pr ogram is deactivated • ECO – Fuel Saver Indicator • Check Gascap • Key FOB Battery Low • Service Keyless System • W rong Key • Push Button or Insert [...]

1. T urn the ignition switch to the ON position (Do not start the engine). 2. Fully depr ess the accelerator pedal, slowly , three times within 10 seconds. 3. T urn the ignition switch to the OFF/LOCK position. NOTE: If the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset. If necessary , repeat[...]

This feature allows you to monitor when you ar e driving in a fuel efficient manner , and it can be used to modify driving habits in order to incr ease fuel economy . • Distance T o Empty (DTE) Shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is determined by a weighted average of the [...]

NOTE: Significant changes in driving style or vehicle loading will greatly af fect the actual drivable distance of the vehicle, regar dless of the DTE displayed value. When the DTE value is less than 30 miles (48 km) estimated driving distance, the DTE display will change to a text display of ⬙ LOW FUEL. ⬙ This display will continue until the v[...]

Keyless Go Display — If Equipped When the ENGINE ST AR T/STOP button is pressed to change ignition switch positions, the Keyless Go icon momentarily appears in the EVIC display showing the new ignition switch position. The round symbol in the middle r otates to point at the new ignition switch position. If desired, the ignition switch position gr[...]

Automatic Compass Calibration This compass is self-calibrating, which eliminates the need to set the compass manually . When the vehicle is new , the compass may appear erratic and the EVIC will display “CAL” until the compass is calibrated. Y ou may also calibrate the compass by completing one or more 360 degree turns (in an ar ea free fr om l[...]

1. T urn the ignition switch ON. 2. Pr ess and hold the COMP ASS button for approxi- mately two seconds. 3. Pr ess the SCROLL button until “Compass V ariance” message and the last variance zone number displays in the EVIC. 4. Pr ess and release FUNCTION SELECT button until the proper variance zone is selected accor ding to the map. 5. Pr ess an[...]

System W arnings (Customer Information Features) Press and r elease the MENU button until “SYSTEM W ARNINGS” displays in the EVIC. Then, press the SCROLL button to display anyone of the following choices. • Oil T emperature Shows the actual oil temperature. • Oil Pressur e Shows the actual oil pressur e. • T ire Pr essure Shows the actual[...]

Lock Doors Automatically at 15 mph (24 km/h) When ON is selected, both doors will lock automatically when the vehicle reaches a speed of 15 mph (24 km/h). T o make your selection, press and r elease the FUNC- TION SELECT button until “ON” or “OFF” appears. Unlock Doors Automatically on Exit When ON is selected, both doors will unlock when t[...]

Headlamps On with W ipers (A vailable with Auto Headlamps Only) When ON is selected, and the headlight switch is in the AUTO (A) position, the headlamps will turn on appr oxi- mately 10 seconds after the wipers are turned on. The headlamps will also turn off when the wipers ar e turned off if they wer e turned on by this feature. T o make your sele[...]

Delay Power Off to Accessories Until Exit When this feature is selected, the power window switches, radio, uconnect™ phone (if equipped), power sunroof (if equipped), and ignition-power ed power out- lets will remain active for up to 60 minutes after the ignition switch is turned OFF . Opening a vehicle door will cancel this feature. T o make you[...]

SALES CODE REQ — AM/FM STEREO RADIO AND 6–DISC CD CHANGER (MP3/WMA AUX JACK) NOTE: The radio sales code is located on the lower right side of the radio faceplate. Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/V olume Control (Rotary) Push the ON/VOLUME control [...]

to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping until you release it. SCAN Button Pressing the SCAN button causes the tuner to sear ch for the next listenable station in AM, FM or Satellite (if equipped) frequenc[...]

4. Adjust the minutes using the right side TUNE/ SCROLL control knob. Press the TUNE/SCROLL control knob to save the time change. 5. T o exit, press any button/knob or wait five seconds. The clock can also be set by pressing the SETUP button and selecting the “SET HOME CLOCK” entry . Once in this display follow the above procedur e, starting at[...]

SCROLL contr ol knob to the right or left to adjust the sound level from the right or left side speakers. Push the rotary TUNE/SCROLL control knob a fifth time and F ADE will display . T urn the TUNE/SCROLL control knob to the left or right to adjust the sound level between the front and r ear speakers. Push the rotary TUNE/SCROLL control knob agai[...]

Program T ype 16-Digit Character Display Personality Persnlty Public Public Rhythm and Blues R & B Religious Music Rel Musc Religious T alk Rel T alk Rock Rock Soft Soft Soft Rock Soft Rck Soft Rhythm and Blues Soft R & B Sports Sports Ta l k Ta l k T op 40 T op 40 W eather W eather By pressing the SEEK button when the Music T ype icon is d[...]

selected within five seconds after pressing the SET but- ton, the station will continue to play but will not be stored into pushbutton memory . Y ou may add a second station to each pushbutton by repeating the above pr ocedure with this exception: Pr ess the SET button twice and SET 2 will show in the display window . Each button can be set for SET[...]

CAUTION! This CD player will accept 4–3/4 in (12 cm) discs only . The use of other sized discs may damage the CD player mechanism. Eject Button — Ejecting Compact Disc(s) Press the EJECT button and the pushbutton with the corresponding number (1-6) wher e the CD was loaded and the disc will unload and move to the entrance for easy removal. Radi[...]

R W/FF (CD MODE) Press and hold FF (Fast Forwar d) and the CD player will begin to fast forward until FF is r eleased, or R W or another CD button is pressed. The R W (Rewind) button works in a similar manner . AM or FM Button (CD MODE) Switches the radio to the radio mode. Notes On Playing MP3/WMA Files The radio can play MP3/WMA files; however , [...]

Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal CD audio tracks and computer files (including MP3/ WMA files). Discs created with an option such as ⬙ keep disc open after writing ⬙ are most likely multisession discs. The use of multisession for CD audio or MP3/ WMA playback may result [...]

ID3 T ag information for artist, song title, and album title are supported for ID3 version 1 tags. ID3 version 2 is not supported by the radios. Playlist files are not supported. MP3 Pr o files are not supported. Playback of MP3/WMA Files When a medium containing MP3/WMA data is loaded, the radio checks all files on the medium. If the medium contai[...]

INFO Button (DISC Mode for MP3/WMA Play) Pressing the INFO button r epeatedly will scroll thr ough the following T AG information: Song T itle, Artist, File Name, and Folder Name (if available). Press the INFO button once mor e to return to ⬙ elapsed time ⬙ priority mode. Press and hold the INFO button for thr ee seconds or more and radio will [...]

TIME Button (Auxiliary Mode) Press the TIME button to change the display fr om elapsed playing time to time of day . The time of day will display for five seconds. R W/FF (Auxiliary Mode) No function. SET Button (Auxiliary Mode) No function. Operating Instructions — V oice Recognition System (VR) (If Equipped) For the radio, refer to “V oice Re[...]

DTS™ ⬙ DTS™ ⬙ and ⬙ DTS™ 2.0 ⬙ are trademarks of Digital The- ater Systems, Inc. SALES CODE (RER/REN) — AM/FM/CD/DVD RADIO – IF EQUIPPED NOTE: The sales code is located on the lower right side of the unit’s faceplate. The REN and RER radios contain a CD/DVD player , USB port, and a 30-gigabyte hard drive (HDD). Sirius Satellite [...]

T o Manually Set the Clock — RER/REN 1. T urn on the radio. 2. T ouch the screen wher e the time is displayed. 3. T ouch the screen wher e “User Clock” is displayed. The clock setting menu will appear on the screen. 4. T o move the hour forward, touch the scr een where the word “Hour” with the arr ow pointing upward is dis- played. T o mo[...]

Show T ime if Radio is Off When selected, this feature will display the time of day on the touch screen when the radio is turned of f. Proceed as follows to change the current setting: 1. T urn on the radio. 2. T ouch the screen wher e the time is displayed. The clock setting menu will appear on the screen. 3. When this featur e is on, a check mark[...]

SALES CODE RES — AM/FM STEREO RADIO WITH CD PLA YER (MP3 AUX JACK) NOTE: The radio sales code is located on the lower right side of the radio faceplate. Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/V olume Control (Rotary) Push the ON/VOLUME control knob to tu[...]

SEEK Buttons Press and r elease the SEEK buttons to search for the next listenable station in AM/FM mode. Press the right switch to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping, until you release it. TIME Button [...]

Push the rotary TUNE/SCROLL control knob a second time and MID will display . T urn the TUNE/SCROLL control knob to the right or left to incr ease or decrease the mid-range tones. Push the rotary TUNE/SCROLL control knob a third time and TREBLE will display . T urn the TUNE/SCROLL control knob to the right or left to incr ease or decrease the trebl[...]

and 12 FM stations to be stored into pushbutton memory . The stations stored in SET 2 memory can be selected by pressing the pushbutton twice. Every time a preset button is used, a corr esponding button number will display . B u t t o n s1-6 These buttons tune the radio to the stations that you commit to pushbutton memory (12 AM and 12 FM stations)[...]

CAUTION! • This CD player will accept 4-3/4 in (12 cm) discs only . The use of other sized discs may damage the CD player mechanism. • Do not use adhesive labels. These labels can peel away and jam the player mechanism. • RES is a single CD player . Do not attempt to insert a second CD if one is already loaded. • Dual-media disc types (one [...]

TIME Button Press this button to change the display fr om a large CD playing time display to a small CD playing time display . R W/FF Press and hold the FF (Fast Forwar d) button and the CD player will begin to fast forward until FF is r eleased, or R W or another CD button is pressed. The R W (Reverse) button works in a similar manner . AM/FM Butt[...]

The radio uses the following limits for file systems: • Maximum number of folder levels: 8 • Maximum number of files: 255 • Maximum number of folders. (The radio display of file names and folder names is limited. For large numbers of files and/or folders, the radio may be unable to display the file name and folder name, and will assign a numb[...]

rates (VBR) are also supported. The majority of MP3 files use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or VBR bit rate. MPEG Specification Sampling Frequency (kHz) Bit Rate (kbps) MPEG-1 Audio Layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 1 12, 96, 80, 64, 56, 48, 40, 32 MPEG-2 Audio Layer 3 24, 22.05, 16 160, 128, 144, 1 12, 96, 80, 6[...]

Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack, which allows the user to plug in a portable device, such as an MP3 player , or cassette player , and utilize the vehicle’s audio system to amplify the source and play thr ough the vehicle speakers. Pressing the DISC/AUX button will change the mode to auxiliar[...]

Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/V olume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio. Electronic V olume Control The electronic volume contr ol turns conti[...]

If your vehicle is not equipped with or this feature is not available on your vehicle, a “Not Equipped W ith UConnect” message will display on the radio screen. TIME Button Press the TIME button to alternate display of the time and radio frequency . Clock Setting Procedure 1. Pr ess and hold the TIME button until the hours blink. 2. Adjust the [...]

TUNE Control T urn the rotary TUNE/SCROLL control knob clockwise to increase or counter clockwise to decrease the fr equency . Setting the T one, Balance, and Fade Push the rotary TUNE/SCROLL control knob and BASS will display . T urn the TUNE/SCROLL control knob to the right or left to increase or decr ease the bass tones. Push the rotary TUNE/SCR[...]

T oggle the MUSIC TYPE button to select the following format types: Program T ype 16-Digit Character Display No program type or un- defined None Adult Hits Adlt Hit Classical Classicl Classic Rock Cls Rock College College Country Country Foreign Language Language Information Inform Jazz Jazz News News Nostalgia Nostalga Oldies Oldies Program T ype [...]

By pressing the SEEK button when the Music T ype icon is displayed, the radio will be tuned to the next frequency station with the same selected Music T ype name. The Music T ype function only operates when in the FM mode. If a preset button is activated while in the Music T ype (Program T ype) mode, the Music T ype mode will be exited and the radi[...]

and 12 FM stations to be stored into pushbutton memory . The stations stored in SET 2 memory can be selected by pressing the pushbutton twice. Every time a preset button is used, a corr esponding button number will display . B u t t o n s1-6 These buttons tune the radio to the stations that you commit to pushbutton memory (12 AM and 12 FM stations)[...]

CAUTION! • This CD player will accept 4–3/4 in (12 cm) discs only . The use of other sized discs may damage the CD player mechanism. • Do not use adhesive labels. These labels can peel away and jam the player mechanism. • RES is a single CD player . Do not attempt to insert a second CD if one is already loaded. • Dual-media disc types (on[...]

R W/FF Press and hold FF (Fast Forwar d) and the CD player will begin to fast forward until FF is r eleased or R W or another CD button is pressed. The R W (Reverse) button works in a similar manner . AM/FM Button Press the button to select either AM or FM mode. SET/RND Button (Random Play Button) Press this button while the CD is playing to activa[...]

• Maximum number of folders. (The radio display of file names and folder names is limited. For large numbers of files and/or folders, the radio may be unable to display the file name and folder name and will assign a number instead. W ith a maximum number of files, exceeding 20 folders will result in this display . W ith 200 files, exceeding 50 f[...]

MPEG Specification Sampling Frequency (kHz) Bit Rate (kbps) MPEG-1 Audio Layer 3 48, 44.1, 32 320, 256, 224, 192, 160, 128, 1 12, 96, 80, 64, 56, 48, 40, 32 MPEG-2 Audio Layer 3 24, 22.05, 16 160, 128, 144, 1 12, 96, 80, 64, 56, 48, 40, 32, 24, 16, 8 ID3 T ag information for artist, song title, and album title are supported for version 1 ID3 tags. [...]

LIST Button (CD Mode for MP3 Play) Pressing the LIST button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the TUNE/SCROLL control knob. Selecting a folder by pressing the TUNE/SCROLL control knob will begin playing the files contained in that folder (or the next folder in sequence if the selection[...]

TIME Button (Auxiliary Mode) Press this button to change the display to time of day . The time of day will display for five seconds (when the ignition is OFF). Operating Instructions - uconnect™ phone (If Equipped) Refer to “uconnect™ phone” in Section 3. Operating Instructions - uconnect™ studios (Satellite Radio) (If Equipped) Refer to [...]

Connecting The iPod 姞 Use the optional connection cable to connect an iPod 威 to the vehicle’s 16–pin connector port located on the center console. Once the iPod 威 is connected and synchronized to the vehicle’s UCI system (iPod 威 may take a few seconds to connect), the iPod 威 starts charging and is ready for use by pr essing radio sw[...]

Play Mode When switched to UCI mode, the iPod 威 automatically starts Play mode. In Play mode, you may use the following buttons on the radio faceplate to control the iPod 威 and display data: • Use the TUNE control knob to select the next or previous track. • T urning it clockwise (forward) by one click, while playing a track, skips to the n[...]

• While a track is playing, press the INFO button to see the associated metadata (artist, track title, album, etc.) for that track. Pressing the INFO button again jumps to the next screen of data for that track. Once you have seen all screens, the last INFO button pr ess will take you back to the play mode screen on the radio. • Pressing the RE[...]

• During all List modes, the iPod 威 displays all lists in “wrap-around” mode. So if the track is at the bottom of the list, just turn the wheel backwards (counter-clockwise) to get to the track faster . • In List mode, the radio PRESET Buttons are used as shortcuts to the following lists on the iPod 威 . • P r e s e t1–P l a y l i s [...]

CAUTION! • Leaving the iPod 威 (or any supported device) any- where in the vehicle in extreme heat or cold can alter the operation or damage the device. Follow the device manufacturer ’ s guidelines. • Placing items on the iPod 威 , or connections to the iPod 威 in the vehicle, can cause damage to the device and/or to the connectors. W ARN[...]

number 888-539-7474, or visit the Sirius web site at www .sirius.com, or at www .siriuscanada.ca for Cana- dian residents. Electronic Serial Number/Sirius Identification Number (ESN/SID) Please have the following information available when calling: 1. The Electr onic Serial Number/Sirius Identification Number (ESN/SID). 2. Y our V ehicle Identifica[...]

bikes should be placed as far rearwar d as possible, within the loading design of the rack. Do not place items directly on or above the antenna. Reception Quality Satellite reception may be interr upted due to one of the following reasons: • The vehicle is parked in an undergr ound parking structur e or under a physical obstacle. • Dense tree c[...]

INFO Button Pressing the INFO button will cycle the display informa- tion between Artist, Song T itle, and Composer (if avail- able). Also, pr essing and holding the INFO button for an additional three seconds will make the radio display the Song T itle all of the time (press and hold again to return to normal display). R W/FF Pressing the R W (Rew[...]

SETUP Button Pressing the SETUP button allows you to select the following items: • Display Sirius ID number — Press the AUDIO/ SELECT button to display the Sirius ID number . This number is used to activate, deactivate, or change the Sirius subscription. SET Button – T o Set the Pushbutton Memory When you are r eceiving a channel that you wis[...]

KICKER 姞 HIGH PERFORMANCE SOUND SYSTEM WITH DRIVER-SELECT ABLE SURROUND (DSS) – IF EQUIPPED Y our vehicle is equipped with a state of the art audio amplifier that provides 5.1-channel surr ound sound from any stereo audio sour ce. A new feature of the Kicker 威 audio system offers the ability to choose surr ound sound for any audio source. “[...]

When in “Audio Surround” mode, balance is set auto- matically . Fader control is available to add more sur - round audio if desir ed. REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system contr ols are located on the surface of the steering wheel at the three and nine o’clock positions. V ehicles equipped with steering wheel-mo[...]

If the Compass/T emp/Audio screen is alr eady displayed when the AUDIO MODE button is pressed, then the mode will change (i.e., from AM to FM, to Media mode, etc., depending on which radio is in the vehicle). FUNCTION SELECT Button When the EVIC is in the Compass/T emp/ Audio screen, pr ess the FUNCTION SELECT button to operate various radio, media[...]

NOTE: If you experience difficulty in playing a particu- lar disc, it may be damaged (i.e., scratched, reflective coating removed, a hair , moisture or dew on the disc) oversized, or have copyright encoding. T ry a known good disc before considering disc player service. RADIO OPERA TION AND CELLULAR PHONES Under certain conditions, the cellular pho[...]

Blower Control Use this control to r egulate the amount of air forced thr ough the ven- tilation system in any mode. The blower speed increases as you move the control to the right fr om the “O” (Off) position. Ther e are four blower speeds. NOTE: For vehicles equipped with Remote Start, the climate controls will not function during Remote Star[...]

Mode Control Use this control to choose fr om several patterns of air distribution. Y ou can select either a primary mode as iden- tified by the symbols on the control, or a blend of two of these modes. • Panel Air is directed thr ough the outlets in the instrument panel and the center console. These outlets can be adjusted to direct airflow . NO[...]

• Defrost Air is directed thr ough the windshield and side window demist outlets. Use this mode with maxi- mum blower and temperature settings for best wind- shield and side window defrosting. NOTE: The air conditioning compressor operates in Mix, Defrost, and Floor or a blend of these modes, even if the Air Conditioning Snowflake button is not p[...]

NOTE: The air conditioning compressor will not engage until the engine has been running for a few seconds. • MAX A/C For maximum cooling use the A/C and r ecirculation buttons at the same time and set the temperature contr ol to full cool by rotating the temperatur e control knob full counterclockwise. • Economy Mode If economy mode is desired,[...]

NOTE: • The feature can be disable by parking the vehicle with the blower control set to the “O” (or OFF) position. • For maximum performance, it is recommended that the vehicle is parked with the blower control set to the “High” (full clockwise) position. Operating Tips NOTE: Refer to the chart at the end of this section for suggested [...]

NOTE: Recirculation without A/C should not be used for long periods as fogging may occur . Side W indow Demisters A side window demister outlet is located at each end of the instrument panel. These non-adjustable outlets dir ect air toward the side windows when the system is in the Floor , Mix, or Defrost mode. The air is dir ected at the area of t[...]

3Control Setting Suggestions for V arious W eather Conditions 4 UNDERST ANDING YOUR INSTRUMENT P ANEL 237[...]

[...]

ST ARTING AND OPERA TING CONTENTS 䡵 Starting Procedur es .................... 2 4 3 ▫ Manual T ransmission — If Equipped ...... 2 4 3 ▫ Automatic T ransmission — If Equipped .... 2 4 4 ▫ Keyless Go — If Equipped .............. 2 4 5 ▫ Normal Starting ..................... 2 4 6 ▫ Extremely Cold W eather (Below ⫺ 20°F Or ⫺ 29?[...]

▫ Five-Speed Automatic T ransmission (5.7L Engine) ........................... 2 6 4 ▫ Gear Ranges ........................ 2 6 4 䡵 AutoStick 威 — If Equipped ............... 2 6 8 ▫ AutoStick 威 Operation ................. 2 6 8 䡵 Driving On Slippery Surfaces ............. 2 6 9 ▫ Acceleration ........................ 2 6 9 ▫ T r[...]

▫ ESP (Electr onic Stability Program) — If Equipped .......................... 2 8 4 ▫ Synchronizing ESP ................... 2 8 7 ▫ ESP/BAS Malfunction Indicator Light And ESP/TCS Indicator Light ............... 2 8 7 䡵 T ire Safety Information ................. 2 8 8 ▫ T ire Markings ....................... 2 8 8 ▫ T ire Loading And[...]

▫ 5.7L Engine (W ith Manual T ransmission) .... 3 1 7 ▫ Reformulated Gasoline ................ 3 1 7 ▫ Gasoline/Oxygenate Blends ............. 3 1 7 ▫ E-85 Usage In Non-Flex Fuel V ehicles ...... 3 1 8 ▫ MMT In Gasoline .................... 3 1 9 ▫ Materials Added T o Fuel ............... 3 1 9 ▫ Fuel System Cautions .................[...]

ST ARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust the inside and outside mirrors, fasten your seat belt, and if present, instr uct all other occupants to buckle their seat belts. W ARNING! • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or [...]

W ARNING! Do not attempt to push or tow your vehicle to get it started. Unburned fuel could enter the catalytic con- verter and once the engine has started, ignite and damage the converter and vehicle. If the vehicle has a discharged battery , booster cables may be used to obtain a start from another vehicle. This type of start can be dangerous if [...]

Do not press the accelerator . Use the Fob with Integrated Key to briefly turn the ignition switch to the ST AR T position and release it as soon as the starter engages. The starter motor will continue to run, and it will disengage automatically when the engine is running. If the engine fails to start, the starter will disengage automatically in 10[...]

NOTE: The ENGINE ST AR T/STOP button should only be removed or inserted with the ignition in the OFF position. Normal Starting Using the ENGINE ST AR T/STOP Button — Automatic T ransmission Only NOTE: Normal starting of either a cold or a warm engine is obtained without pumping or pressing the accelerator pedal. T o start the engine, the transmis[...]

2. The ignition switch will r eturn to the OFF position. 3. If the shift lever is not in P ARK, the ENGINE ST ART/ STOP button must be held for two seconds and vehicle speed must be above 5 mph (8 km/h) before the engine will shut off. The ignition switch position will r emain in the ACC position until the shift lever is in P ARK and the button is [...]

switch position will remain in the ACC position until the vehicle is stopped and the button is pressed twice to the OFF position. Keyless Go Functions – W ith Driver ’ s Foot OFF the Brake Pedal/Clutch Pedal (In P ARK or NEUTRAL Position) The Keyless Go feature operates similar to an ignition switch. It has four positions, OFF , ACC, ON/RUN and[...]

If Engine Fails T o Start W ARNING! • Never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury . • Do not attempt to push or tow your vehicle to get it started. V ehicles equipped with an automatic trans- mission cann[...]

and hold the clutch pedal, push the accelerator pedal all the way to the floor and hold it, then press and hold the ENGINE ST AR T/STOP button for no more than 15 sec- onds. Release the accelerator pedal and the clutch pedal, wait 10 to 15 seconds, then repeat the “Normal Starting” procedur e. Clearing A Flooded Engine (Using Fob W ith Integrat[...]

W ARNING! Remember to disconnect the cord before driving. Damage to the 1 10-1 15 V olt electrical cord could cause electrocution. MANUAL TRANSMISSION — IF EQUIPPED Six-Speed Manual T ransmission W ARNING! Y ou or others could be injured if you leave the vehicle unattended without having the parking brake fully applied. The parking brake should a[...]

NOTE: During cold weather , you may experience in- creased ef fort in shifting until the transmission fluid warms up. This is normal. Shifting Fully press the clutch pedal befor e shifting gears. As you release the clutch pedal, lightly pr ess the accelerator pedal. The six-speed manual transmission has a spring that centers the shift lever near th[...]

Recommended Shift Speeds T o utilize your manual transmission efficiently for fuel economy , it should be upshifted as listed in recom- mended shift speed chart. MANUAL TRANSMISSION RECOMMENDED SHIFT SPEEDS Axle Ratio 1-4 4-5 5-6 3.73 mph 20 25 42 (km/h) (32) (40) (67) 3.91 mph 20 37 48 (km/h) (32) (59) (77) Earlier upshifts during cruise condition[...]

1–4 Skip Shift There ar e times when you must shift the transmission directly fr om first gear to fourth gear instead of from first gear to second gear . This is to help you get the best possible fuel economy from your vehicle. This occurs when the engine coolant (antifreeze) is higher than 106°F (41°C), vehicle speed is greater than 19 mph (30[...]

AUTOMA TIC TRANSMISSION — IF EQUIPPED CAUTION! Damage to the automatic transmission may occur if the following precautions are not observed: • Shift into P ARK only after the vehicle has come to a complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed. • Do not shift [...]

• Shift lever position • Accelerator position • V ehicle speed The gear shifting process is continuously adapted, de- pendent on the driving style, the driving situation, and the road characteristics. NOTE: • After selecting any driving position, wait a moment to allow the gear to engage fully before accelerating, especially when the engine[...]

W ARNING! Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, you should always shift the transmission into P ARK, remove the key from the ignition, and apply the parking brake. Once the key is removed from the ignit[...]

the override (using a flat-bladed screwdriver), car efully remove the override cover which is located to the right of the shift lever . 1. T urn the key to the ACC or ON position without starting the engine. 2. Firmly set the parking brake. 3. Pr ess and maintain firm pressure on the brake pedal. 4. Using the scr ewdriver , press and hold the overr[...]

W ith Keyless Go — If Equipped If the engine is running, pr ess the ST ART/ST OP button to turn it off. Release the brake pedal and pr ess the ST AR T/ STOP button once or twice to go to the ACC or ON/RUN position. Do not start the engine. Then, follow the in- structions shown above to activate the override. Four-Speed Automatic T ransmission (3.[...]

When parking on a flat surface, place the shift lever in the P ARK position first, and then apply the parking brake. When parking on a hill, it is important to set the parking brake before placing the shift lever in P ARK, otherwise the load on the transmission locking mechanism may make it difficult to move the shift lever out of park. As an added[...]

CAUTION! Coasting the vehicle or driving for any other reason with shift lever in NEUTRAL can result in transmis- sion damage. W ARNING! Do not coast in NEUTRAL and never turn of f the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions. Y ou might lose control of the vehicle and[...]

“3” (Third) This range eliminates shifts into Overdrive. The transmis- sion will operate normally in 1st, 2nd, and 3rd while in this range. The “3” position should also be used when descending steep grades to prevent brake system dis- tress. NOTE: Using the “3” range while operating the vehicle under heavy operating conditions will impr[...]

NOTE: • The torque converter clutch will not engage until the transmission fluid and engine coolant is warm (usu- ally after 1–3 miles [1.6–4.8 km] of driving). Because engine speed is higher when the torque converter clutch is not engaged, it may seem as if the transmis- sion is not shifting into Overdrive when cold. This is considered a nor[...]

NOTE: Even if the transmission can be reset, we r ecom- mend that you visit an authorized dealer at your earliest possible convenience. Y our authorized dealer has diag- nostic equipment to determine if the problem could recur . If the transmission cannot be reset, authorized dealer service is requir ed. Five-Speed Automatic T ransmission (5.7L Eng[...]

When parking on a flat surface, place the shift lever in the P ARK position first, and then apply the parking brake. When parking on a hill, it is important to set the parking brake before placing the shift lever in P ARK, otherwise the load on the transmission locking mechanism may make it difficult to move the shift lever out of P ARK. As an adde[...]

NEUTRAL This range is used when vehicle is standing for pro- longed periods with engine running. Engine may be started in this range. Set the parking brake if you must leave the vehicle. CAUTION! Coasting the vehicle or driving for any other reason with the shift lever in NEUTRAL can result in transmission damage. W ARNING! Do not coast in NEUTRAL [...]

T emporary T ransmission Limp Home Mode The transmission is monitored for abnormal conditions. If a condition is detected that could result in transmission damage, the transmission will engage Limp Home Mode. If vehicle acceleration worsens or the transmission no longer shifts, the transmission is most likely operating in the Limp Home Mode. In thi[...]

AUTOSTICK 姞 — IF EQUIPPED Autostick 威 is a driver-interactive transmission that of fers manual gear shifting to provide you with mor e control of the vehicle. Autostick 威 allows you to maximize engine braking, eliminate undesirable upshifts and downshifts, and improve overall vehicle performance. This system can also provide you with mor e [...]

• Y ou can start out in first or second gear . The system will ignore attempts to upshift at too low of a vehicle speed. • The transmission will automatically downshift to first gear when coming to a stop. • Starting out in second gear is helpful in snowy or icy conditions. • A void using speed control when Autostick 威 is en- gaged. • T[...]

T raction When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and r oad surface. This is known as hydroplaning and may cause partial or complete loss of vehicle control and stopping ability . T o reduce this possibility , the following precau- tions should be observed: 1. Slow down during rainstorms[...]

Flowing/Rising W ater W ARNING! Do not drive on, or cross, a road or a path where water is flowing and/or rising (as in storm run-off). Flowing water can wear away the road or path’s surface and cause your vehicle to sink into deeper water . Furthermore, flowing and/or rising water can carry your vehicle away swiftly . Failure to follow this warn[...]

CAUTION! (Continued) • Driving through standing water may cause dam- age to your vehicle’ s drivetrain components. Al- ways inspect your vehicle’ s fluids (i.e., engine oil, transmission, axle, etc.) for signs of contamination (i.e., fluid that is milky or foamy in appearance) after driving through standing water . Do not con- tinue to operat[...]

POWER STEERING The standard power steering system will give you good vehicle response and incr eased ease of maneuverability in tight spaces. The system will provide mechanical steering capability if power assist is lost. If for some reason the power assist is interr upted, it will still be possible to steer your vehicle. Under these condi- tions, [...]

apparent, and/or the system is not functioning as antici- pated. Coordinate inspection ef forts through an autho- rized dealer . CAUTION! Do not use chemical flushes in your power steering system as the chemicals can damage your power steering components. Such damage is not covered by the New V ehicle Limited W arranty . W ARNING! Fluid level shoul[...]

When parking on a hill, it is important to apply the parking brake before placing the shift lever in P ARK, otherwise the load on the transmission locking mecha- nism may make it difficult to move the shift lever out of P ARK. As an added precaution, turn the front wheels toward the curb on a downhill grade and away fr om the curb on an uphill grad[...]

Automatic T ransmission — If Equipped The foot operated parking brake is positioned below the lower left corner of the instrument panel. T o apply the parking brake, push the parking brake pedal down and then remove your foot fr om the pedal. T o release the parking brake, push down on the parking brake pedal and then release. W ARNING! Never use[...]

W ARNING! • Never leave children alone in a vehicle. Leaving unattended children in a vehicle is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Do not leave the key in the ignition. A child could operate power win- dows, other controls, or move the vehicle. • Be sure the parking brake is fully diseng[...]

When the vehicle is driven over 7 mph (1 1 km/h), you may also hear a slight clicking sound as well as some related motor noises. These noises ar e the system per- forming its self check cycle to ensure that the ABS system is working properly . This self check occurs each time the vehicle is started and accelerated past 7 mph (1 1 km/h). ABS is act[...]

W ARNING! (Continued) • Pumping of the anti-lock brakes will diminish their effectiveness and may lead to an accident. Pumping makes the stopping distance longer . Just press firmly on your brake pedal when you need to slow down or stop. • The Anti-Lock Brake System (ABS) cannot prevent the natural laws of physics from acting on the vehicle, no[...]

requir ed. However , the conventional brake system will continue to operate normally if the “Brake W arning Light” is not on. If the “ABS W arning Light” is on, the brake system should be serviced as soon as possible to restor e the benefits of anti-lock brakes. If the “ABS W arning Light” does not come on when the ignition switch is tu[...]

avoid skidding on slippery surfaces during braking. For more information about ABS, refer to “Anti-Lock Brake System” in Section 5. W ARNING! The ABS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. The ABS cannot prevent accidents, including those re[...]

situation by sensing the rate and amount of brake appli- cation and then applies optimum pressur e to the brakes. This can help reduce braking distances. Applying the brakes very quickly results in the best BAS assistance. T o receive the benefits of this system, you must apply continuous brake pedal pressur e during the stopping sequence. Do not r[...]

HSA (Hill Start Assist) — Manual T ransmission Only The HSA system is designed to assist the driver when starting a vehicle from a stop on a hill. HSA will maintain the level of brake pressur e the driver applied for a short period of time after the driver takes their foot off of the brake pedal. If the driver does not apply the throttle during t[...]

For vehicles not equipped with the EVIC, perform the following steps: NOTE: Y ou must complete Steps 1 through 8 within 90 seconds. 1. Center the steering wheel (fr ont wheels pointing straight forward). 2. Shift the transmission into NEUTRAL. 3. Apply the parking brake. 4. Start the engine. 5. Release the clutch pedal. 6. Rotate the steering wheel[...]

The ESP uses sensors in the vehicle to determine the path that the driver intends to steer the vehicle and compares it to the actual path of the vehicle. When the actual path does not match the intended path, the ESP applies the brake of the appropriate wheel to assist in counteracting the condition of oversteer or understeer . • Oversteer - when[...]

The ESP system has two available operating modes: ESP On This is the normal operating mode for the ESP . Whenever the vehicle is started, the ESP system will be in this mode. This mode should be used for most driving situations. The ESP should only be turned OFF for specific r easons as noted in the following paragraphs. Partial Of f The “Partial[...]

NOTE: T o improve the vehicle’s traction when driving with snow chains, or when starting off in deep snow , sand, or gravel, it may be desirable to switch to the “Partial Off” mode by momentarily pr essing the “ESP OFF” switch. Once the situation requiring “Partial Of f” mode is overcome, turn the ESP ON again by momen- tarily pressin[...]

NOTE: • The “ESP/TCS Indicator Light” and the “ESP/BAS Malfunction Indicator Light” will turn on momen- tarily each time the ignition switch is turned ON. • Each time the ignition is turned ON, the ESP System will be ON even if it was turned OFF previously . • The ESP Contr ol System will make buzzing or clicking sounds when it is act[...]

NOTE: • P (Passenger) - Metric tir e sizing is based on U.S. design standards. P-Metric tir es have the letter “P” molded into the sidewall preceding the size designa- tion. Example: P215/65R15 95H. • European-Metric tir e sizing is based on European design standards. T ires designed to this standar d have the tire size molded into the side[...]

T ire Sizing Chart TIRE SIZING TERMS Size Designation: P = Passenger Car tire size based on U.S. design standar ds ⴖ ....blank.... ⴖ = Passenger Car tire based on Eur opean design standards LT = Light T ruck tire based on U.S. design standar ds T = T emporary spare tir e 31 = Overall diameter in inches (in) 215 = Section width in millimeters (m[...]

TIRE SIZING TERMS Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — The maximum speed corresponding to the speed symbol should [...]

T ire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however , the date code may only be on one side. T ires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle[...]

Tire Loading and T ire Pressure T ire Placard Location NOTE: The proper cold tir e inflation pressur e is listed on the driver’s side B-Pillar . T ire and Loading Information Placard This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size de[...]

Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. Y ou will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tir e size, and cold tire inflation pressur es specified on the T ire and Loading Information placard and in the “V ehicle Loading”[...]

4. The r esulting figure equals the available amount of cargo and luggage load capacity . For example, if “XXX” amount equals 1,400 lbs (635 kg) and there will be five 150 lb (68 kg) passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (295 kg) (since 5 x 150 = 750, and 1400 – 750 = 650 lbs [295 kg]).[...]

296 ST ARTING AND OPERA TING[...]

W ARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMA TION Tire Pressure Proper tir e inflation pressur e is essential to the safe and satisfactory [...]

W ARNING! (Continued) • Unequal tire pressures from one side of the ve- hicle to the other can cause the vehicle to drift to the right or left. • Always drive with each tire inflated to the recom- mended cold tire inflation pressure. Economy Improper inflation pr essures can cause uneven wear patterns to develop across the tir e tread. These ab[...]

CAUTION! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressur es specified on the placard ar e always “cold tire inflation pr essure.” Cold tir e inflation pressure is defined as the tire pr e[...]

loading may be requir ed for high-speed vehicle opera- tion. Refer to original equipment or an authorized tire dealer for recommended safe operating speeds, loading and cold tire inflation pr essures. W ARNING! High speed driving with your vehicle under maxi- mum load is dangerous. The added strain on your tires could cause them to fail. Y ou could[...]

W ARNING! T emporary use spare tires are for emergency use only . W ith these tires, do not drive more than 50 mph (80 km/h). T emporary use spare tires have limited tread life. When the tread is worn to the tread wear indicators, the temporary use spare tire needs to be replaced. Be sure to follow the warnings, which apply to your spare. Failure t[...]

W ARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure some- one. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) for more than 30 seconds continu- ously when you are stuck, and do not let anyone near a spinning wheel, no matte[...]

Life Of Tire The service life of a tire is dependent upon varying factors including, but not limited to: • Driving style • T ire pressur e • Distance driven W ARNING! T ires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. Y ou could los[...]

W ARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change sus- pension dimensions and performance characteris- tics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredict- able handling and stress to steeri[...]

NOTE: Do not use tire chains on a compact spar e tire. CAUTION! T o avoid damage to your vehicle or tires, observe the following precautions: • Because of restricted chain clearance between tires and other suspension components, it is important that only chains in good condition are used. Bro- ken chains can cause serious damage. Stop the vehicle[...]

Always use the lower suggested operating speed if both the chain manufacturer and vehicle manufactur er sug- gest a maximum speed. This notice applies to all chain traction devices, including link and cable (radial) chains. SNOW TIRES Some areas of the country r equire the use of snow tir es during the winter . Standard tir es are of the all season[...]

The suggested rotation method for vehicles equipped with all season tires is the “forwar d-cross” as shown in the following diagram. TIRE PRESSURE MONITOR SYSTEM (TPMS) The T ire Pressur e Monitor System (TPMS) will warn the driver of a low tire pr essure based on the vehicle r ecom- mended cold placard pr essure. The tire pr essure will vary w[...]

The TPMS will warn the driver of a low tire pr essure if the tire pr essure falls below the low-pr essure warning limit for any reason, including low temperatur e effects and natural pressur e loss through the tir e. The TPMS will continue to warn the driver of low tire pressur e as long as the condition exists, and will not turn off until the tir [...]

CAUTION! • The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when us- ing replacement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause [...]

• Seasonal temperature changes will af fect tire pr essure, and the TPMS will monitor the actual tire pr essure in the tire. Base System The T ire Pressur e Monitor System (TPMS) uses wireless technology with wheel rim mounted electronic sensors to monitor tire pr essure levels. Sensors mounted to each wheel as part of the valve stem transmit tir[...]

turn off when the fault condition no longer exists. A system fault can occur due to any of the following: 1. Signal interfer ence due to electronic devices or driving next to facilities emitting the same radio frequencies as the TPM sensors. 2. Installing aftermarket window tinting that contains materials that may block radio wave signals. 3. Accum[...]

Premium System — If Equipped The T ire Pressur e Monitor System (TPMS) uses wireless technology with wheel rim mounted electronic sensors to monitor tire pr essure levels. Sensors mounted to each wheel as part of the valve stem transmit tire pr essure readings to the r eceiver module. NOTE: It is particularly important for you to check the tire p[...]

Should this occur , you should stop as soon as possible and inflate all of the tires with low pr essure (including those flashing in the EVIC graphic) to the vehicle’s recommended cold placar d pressur e value. Once the system receives the updated tir e pressur es, the system will automatically update, the graphic display in the EVIC will stop fl[...]

Check TPMS W arning If a system fault is detected, the “TPM T elltale Light” will flash on and off for 75 seconds and then r emain on solid. The system fault will also sound a chime. In addition, the EVIC will display a ⬙ CHECK TPM SYSTEM ⬙ message for three seconds and then display dashes (- -) in place of the pressur e value to indicate w[...]

V ehicles with Compact Spare 1. The compact spar e tire does not have a TPM sensor . Therefor e, the TPMS will not monitor the pressur e in the compact spare tir e. 2. If you install the compact spar e tire in place of a road tire that has a pr essure below the low-pr essure warning limit, upon the next ignition key cycle, the “TPM T elltale Ligh[...]

General Information This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference r eceived, including interference that may cause undesir ed operation. The TPM sensors are r egulate[...]

as hard starting, stalling, and hesitations. If you experi- ence these symptoms, try another brand of gasoline before considering service for the vehicle. Over 40 auto manufacturers worldwide have issued and endorsed consistent gasoline specifications (the W orld W ide Fuel Charter , WWFC) which define fuel properties necessary to deliver enhanced [...]

CAUTION! DO NOT use gasolines containing Methanol or E85 Ethanol. Use of these blends may result in starting and driveability problems and may damage critical fuel system components. Problems that r esult from using methanol/gasoline or E85 ethanol blends are not the r esponsibility of the manufacturer . While MTBE is an oxygenate made from methano[...]

MMT In Gasoline MMT is a manganese-containing metallic additive that is blended into some gasoline to increase octane. Gasoline blended with MMT provides no performance advantage beyond gasoline of the same octane number without MMT . Gasoline blended with MMT reduces spark plug life and reduces emissions system performance in some vehicles. The ma[...]

• The use of fuel additives, which are now being sold as octane enhancers, is not recommended. Most of these products contain high concentrations of methanol. Fuel system damage or vehicle performance problems resulting fr om the use of such fuels or additives is not the responsibility of the manufactur er . NOTE: Intentional tampering with the e[...]

ADDING FUEL Fuel Filler Cap (Gas Cap) The gas cap is located behind the fuel filler door on the left side of the vehicle. Use a finger to pull open the door . If the gas cap is lost or damaged, be sure the r eplacement cap is for use with this vehicle. NOTE: When removing the fuel filler cap, lay the cap tether in the hook, located on the fuel fill[...]

CAUTION! • Damage to the fuel system or emissions control system could result from using an improper fuel tank filler tube cap (gas cap). • A poorly fitting gas cap could let impurities into the fuel system. • A poorly fitting gas cap may cause the Malfunc- tion Indicator Light (MIL) to turn on. • T o avoid fuel spillage and overfilling, do[...]

Loose Fuel Filler Cap Message If the vehicle diagnostic system determines that the fuel filler cap is loose, improperly installed, or damaged, a “Check Gascap” message will display in the Electronic V ehicle Information Center (EVIC). If this occurs, tighten the fuel filler cap properly and pr ess the TRIP ODOM- ETER button to turn off the mess[...]

Gross V ehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle. This includes driver , passengers, and cargo. The total load must be limited so that you do not exceed the GVWR. Gross Axle Weight Rating (GA WR) The GA WR is the maximum capacity of the front and r ear axles. Distribute the load over the front and r ear axl[...]

Loading T o load your vehicle properly , first figure out its empty weight, axle-by-axle and side-by-side. Store heavier items down low and be sure you distribute their weight as evenly as possible. Stow all loose items securely befor e driving. If weighing the loaded vehicle shows that you have exceeded either GA WR, but the total load is within t[...]

Gross T railer W eight (GTW) The GTW is the weight of the trailer plus the weight of all cargo, consumables, and equipment (permanent or tem- porary) loaded in or on the trailer in its ⬙ loaded and ready for operation ⬙ condition. The r ecommended way to measure GTW is to put your fully loaded trailer on a vehicle scale. The entire weight of th[...]

that typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling. W eight-Carrying Hitch A weight-carrying hitch supports the trailer tongue weight, just as if it were luggage located at a hitch ball or some other connecting point of the vehicle. These kinds of hitches[...]

T railer Hitch Classification The following chart provides the industry standar d for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Refer to the “T railer T owing W eights (Maximum T railer W eight Ratings)” chart for the[...]

T railer T owing Weights (Maximum T railer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/T ransmission Frontal Area Max. GTW (Gross T railer Wt.) Max. T ongue Wt. 3.5L Automatic 12 sq ft (1.1 1 sq m) 1,000 lbs (454 kg) 100 lbs (45 kg) 5.7L Automatic 12 sq ft (1.1 1 sq m) 1,[...]

Consider the following items when computing the weight on the rear axle of the vehicle: • The tongue weight of the trailer . • The weight of any other type of cargo or equipment put in or on your vehicle. • The weight of the driver and all passengers. NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. [...]

W ARNING! (Continued) Make certain that the load is secured in the trailer and it will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control. Y ou could lose control of your vehicle and have an accident. • When hauling cargo or towing a trailer , do [...]

T owing Requirements — T ires − Do not attempt to tow a trailer while using a compact spare tir e. − Proper tir e inflation pressur es are essential to the safe and satisfactory operation of your vehicle. Refer to “T ires–General Information” for proper tir e inflation procedur es. − Check the trailer tires for pr oper tire inflation [...]

CAUTION! If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes, and they should be of adequate capacity . Failure to do this could lead to accelerated brake lining wear , higher brake pedal effort, and longer stopping distances. W ARNING! • Do not connect trailer brakes to your vehicle’s hydraulic brake lines.[...]

The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector . Refer to the following illustrations. Four-Pin Connector 1 — Female Pins 4 — Park 2 — Male Pin 5 — Left Stop/T urn 3 — Ground 6 — Right Stop/T urn Seven-Pin Connector 1 — Battery 5 — Ground 2 — Backup Lamps 6 — Left [...]

T owing Tips Before setting out on a trip, practice turning, stopping, and backing up the trailer in an area located away fr om heavy traffic. Automatic T ransmission The DRIVE range can be selected when towing. How- ever , if frequent shifting occurs while in this range, use the Electronic Range Select (ERS) or Autostick 威 mode (if equipped) to [...]

performance. For example, choose “4” if the desired speed can be maintained. Choose “3” or “2” if needed to maintain the desired speed. − Extended driving at high RPM should be avoided to prevent excess heat generation. A reduction in vehicle speed may be requir ed to avoid extended driving at high RPM. Return to a higher gear range o[...]

WHA T T O DO IN EMERGENCIES CONTENTS 䡵 Hazard W arning Flasher ................ 3 3 8 䡵 If Y our Engine Overheats ................ 3 3 8 䡵 TIREFIT T ire Repair — If Equipped ........ 3 3 9 䡵 Jacking And T ire Changing ............... 3 4 5 ▫ Jack Location/Spare T ire Stowage ........ 3 4 5 ▫ Preparations For Jacking ............... 3 [...]

HAZARD W ARNING FLASHER The Hazard W arning flasher switch is located in the switch bank near the bottom center of the instrument panel. Press the switch to turn on the Hazar d W arning flasher . When the switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emer gency . Press the switch a second tim[...]

CAUTION! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads 240°F (1 16 °C) or greater pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range 200– 230°F (93–1 10°C). If the pointer remains at 240°F (1 16°C) or greater [...]

The TIREFIT system is located under an access panel in the trunk. 1. Air pump hose 2. Power plug and cable 3. AIR PUMP switch 4. Pr essure gauge 5. TIREFIT sealant bottle 6. TIREFIT sealant hose TIREFIT Location TIREFIT Kit 340 WHA T TO DO IN EMERGENCIES[...]

W ARNING! • Do not attempt to repair a tire on the side of the vehicle close to traffic. Pull far enough of f the road to avoid the danger of being hit when operating the jack or repairing a tire. • Cuts or punctures larger than approximately 0.16 in (4 mm), tire damage caused by driving with extremely low tire pressure or on a flat tire, or a [...]

Sealing T ire with TIREFIT 1. T urn on the Hazard W arning Flashers. 2. Move the shift lever into P ARK (automatic transmis- sion) or in gear (manual transmission), turn OFF the engine and set the parking brake. 3. Remove the TIREFIT kit fr om the trunk. 4. Pull the power plug 2 and the TIREFIT sealant hose 6 out from the TIREFIT kit. 5. Unscr ew t[...]

13. T urn on the Hazard W arning Flashers. 14. Move the shift lever into P ARK (automatic transmis- sion) or in gear (manual transmission), turn OFF the engine and set the parking brake. 15. Disconnect the air pump hose 1 fr om the underside of the sealant bottle 5 by flipping the hose valve open. 16. Connect the air pump hose valve to the tir e va[...]

24. Connect the air pump hose valve to the tir e valve and flip the hose valve closed. 25. Check the pr essure in the tire by r eading the pressur e gauge 4. If the pressur e is 19 psi (1.3 bar) or greater , proceed to the following step. NOTE: If the pr essure is less than 19 psi (1.3 bar), the tire is too badly damaged. Do not attempt to drive th[...]

• If TIREFIT is liquid, clean water and a damp cloth will remove the material fr om the vehicle or tire and wheel components. Once TIREFIT sealing material has dried, it can easily be peeled off and pr operly discarded. • Do not exceed 55 mph (90 km/h) until the tire has been inspected. JACKING AND TIRE CHANGING W ARNING! • Do not attempt to [...]

NOTE: The spare tir e must be removed in or der to access the jack. 1. Open the trunk. 2. Lift the access cover using the pull strap. 3. Remove the fastener securing the spar e tire. 4. Remove the spar e tire. Opening The Access Panel Spare T ire Fastener 346 WHA T TO DO IN EMERGENCIES[...]

5. Remove the fastener securing the jack. W ARNING! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the ve- hicle. Always stow the jack parts and the spare tire in the places provided. Preparations For Jacking 1. Park the vehicle on a firm, level surface as far fr om the edge of the roadway as possibl[...]

2. Set the parking brake. 3. Place the shift lever into P ARK (automatic transmis- sion) or REVERSE (manual transmission). 4. T urn OFF the ignition. 5. T urn on the Hazard W arning flashers. 6. Block the front and rear of the wheel diagonally opposite of the jack- ing position. For example, if changing the right front tir e, block the left rear wh[...]

W ARNING! (Continued) • Do not get under the vehicle when it is on a jack. • Only use the jack in the positions indicated and for lifting this vehicle during a tire change. • If working on or near a roadway , be extremely careful of motor traffic. • T o assure that spare tires, flat or inflated, are securely stowed, spares must be stowed wi[...]

W ARNING! T o avoid possible personal injury , handle the wheel covers with care to avoid contact with the metal edges and retention teeth. 3. Befor e raising the vehicle, use the lug wrench to loosen, but not remove, the lug nuts on the wheel with the flat tire. T urn the lug nuts counter clockwise one turn while the wheel is still on the ground. [...]

5. Raise the vehicle just enough to r emove the flat tire and install the spare tir e. W ARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove the lug nuts, wheel cover (if equipped), and tire. Remove the co[...]

8. Install the lug nuts with the cone shaped end of the nut toward the wheel. Lightly tighten the lug nuts. T o avoid the risk of forcing the vehicle of f the jack, do not tighten the lug nuts fully until the vehicle is lowered to the ground. 9. Lower the vehicle to the gr ound by turning the jack handle counterclockwise. 10. Finish tightening the [...]

• Keep tire inflated to 60 psi (414 KPa) cold inflation pressur e. • This tire is designed as an emer gency spare only . Do not exceed 50 mph (80 km/h) speed. W ARNING! The limited-use spare tires are for emergency use only . Installation of this limited-use spare tire affects vehicle handling. W ith this tire, do not drive more than 60 mph (10[...]

2. Install two lug nuts on the mounting studs, which ar e on each side of the stud that is in alignment with the valve stem. Install the lug nuts with the cone shaped end of the nut toward the wheel. Lightly tighten the lug nuts. T o avoid the risk of forcing the vehicle of f the jack, do not tighten the lug nuts fully until the vehicle is lowered [...]

3. Align the valve notch in the wheel cover with the valve stem on the wheel. Install the cover by hand, snapping the cover over the two lug nuts. Do not use a hammer or excessive force to install the cover . 4. Install the r emaining lug nuts with the cone shaped end of the nut toward the wheel. Lightly tighten the lug nuts. T o avoid the risk of [...]

JUMP-ST ARTING W ARNING! • T ake care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is ON. Y ou can be hurt by the fan. • Do not attempt to push or tow your vehicle to get it started. V ehicles equipped with an automatic transmission cannot be started this way . Unburned fuel could ent[...]

NOTE: The battery is stored under an access cover in the trunk. Remote battery terminals ar e located in the engine compartment for jump-starting. 1. W ear eye protection and r emove any metal jewelry such as watchbands or bracelets that might make an inadvertent electrical contact. 2. When boost is pr ovided by a battery in another vehicle, park t[...]

6. Connect the other cable, first to the negative terminal of the booster battery and then to the engine ground (-) of the vehicle with the discharged battery . Make sure you have a good contact on the engine ground. Refer to the following illustration for jump-starting connections. 7. Start the engine in the vehicle that has the booster battery . [...]

W ARNING! • Y ou should not try to start your vehicle by pushing or towing. • Do not connect the cable to the negative post of the discharged battery . The resulting electrical spark could cause the battery to explode. • During cold weather when temperatures are be- low the freezing point, electrolyte in a discharged battery may freeze. Do no[...]

W ARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure some- one. Do not spin your vehicle’s wheels faster than 35 mph (55 km/h) when you are stuck, and don’t let anyone near a spinning wheel, no matter what the speed. TOWING A DISABLED VEH[...]

If the transmission is not operative or if the vehicle is to be towed more than 15 miles (24 km), the vehicle must be transported using a flatbed truck. CAUTION! • Do not attempt to tow this vehicle from the front with sling-type towing equipment. Damage to the front fascia will result. • If the transmission is not operative or if the vehicle i[...]

[...]

MAINT AINING YOUR VEHICLE CONTENTS 䡵 Engine Compartment — 3.5L ............. 3 6 6 䡵 Engine Compartment — 5.7L ............. 3 6 7 䡵 Onboard Diagnostic System — OBD II ...... 3 6 8 ▫ Loose Fuel Filler Cap ................. 3 6 8 䡵 Emissions Inspection And Maintenance Programs ............................ 3 6 9 䡵 Replacement Parts [...]

▫ Exhaust System ..................... 3 8 1 ▫ Cooling System ..................... 3 8 4 ▫ Brake System ....................... 3 8 9 ▫ Clutch Hydraulic System — Manual T ransmission (If Equipped) ............. 3 9 2 ▫ Manual T ransmission — If Equipped ...... 3 9 2 ▫ Automatic T ransmission — If Equipped .... 3 9 3 ▫ Rear Axle[...]

䡵 Fluids And Capacities .................. 4 1 4 䡵 Fluids, Lubricants, And Genuine Parts ....... 4 1 5 ▫ Engine ............................ 4 1 5 ▫ Chassis ........................... 4 1 6 7 MAINT AINING YOUR VEHICLE 365[...]

ENGINE COMP ARTMENT — 3.5L 1 — Integrated Power Module 6 — Engine Coolant Reservoir 2 — Air Cleaner Filter 7 — Engine Oil Fill 3 — Brake Fluid Reservoir Access Cover 8 — Engine Oil Dipstick 4 — Coolant Pressur e Cap 9 — W asher Fluid Reservoir 5 — Power Steering Fluid Reservoir 10 — Remote Jump-Start Positive Battery Post 366 [...]

ENGINE COMP ARTMENT — 5.7L 1 — Integrated Power Module 6 — Air Cleaner Filter 2 — Coolant Pressur e Cap 7 — Engine Oil Fill 3 — Brake Fluid Reservoir Access Cover 8 — Engine Oil Dipstick 4 — Engine Coolant Reservoir 9 — Remote Jump-Start Positive Battery Post 5 — Power Steering Fluid Reservoir 10 — W asher Fluid Reservoir 7 MA[...]

ONBOARD DIAGNOSTIC SYSTEM — OBD II Y our vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems ar e operating properly , your vehicle will provide excellent performance and fuel economy , as wel[...]

T rip Odometer button to turn off the message. If the problem continues, the message will appear the next time the vehicle is started. A loose, improperly installed, or damaged fuel filler cap may also turn on the MIL. EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requir ement to pass an inspection of this vehi[...]

5. Appr oximately 15 seconds later , one of two things will happen: a. The MIL will flash for about 10 seconds and then return to being fully illuminated until you turn OFF the ignition key or start the engine. This means that the vehicle’s OBD II system is not ready and you should not proceed to the I/M station. b. The MIL will not flash at all [...]

DEALER SERVICE Y our authorized dealer has the qualified service person- nel, special tools, and equipment to perform all service operations in an expert manner . Service manuals are available which include detailed service information for your vehicle. Refer to these service manuals before attempting any procedur e yourself. NOTE: Intentional tamp[...]

CAUTION! (Continued) • Y our vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance intervals. Do not use chemical flushes in these components as the chemicals can damage your engine, transmission, power steering or air condi- tioning. Such damage is not covered [...]

regular intervals, such as every fuel stop. The best time to check the engine oil level is about five minutes after a fully warmed engine is shut off. Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level r eadings. Maintain the oil level in the “SAFE” range. Adding 1.0 qt (1.0 L) of oil when the readi[...]

American Petroleum Institute (API) Engine Oil Identification Symbol This symbol means that the oil has been certified by the American Petroleum Institute (API). The manufacturer only r ecommends API Certified engine oils. CAUTION! Do not use chemical flushes in your engine oil as the chemicals can damage your engine. Such damage is not covered by t[...]

operation of the Multi-Displacement System (MDS). Re- fer to “Multi-Displacement System” under “Starting and Operating” for more details. Lubricants that do not have both, the engine oil certifi- cation mark and the correct SAE viscosity grade number should not be used. Synthetic Engine Oils Y ou may use synthetic engine oils provided the r[...]

Engine Air Cleaner Filter Refer to the “Maintenance Schedule” in Section 8 for proper maintenance intervals. W ARNING! The air induction system (air cleaner , hoses, etc.) can provide a measure of protection in the case of engine backfire. Do not remove the air induction system (air cleaner , hoses, etc.) unless such removal is necessary for re[...]

W ARNING! • Battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or clothing. Do not lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area imme- diately with large amounts of water . • Battery gas is flammable and explosive. Kee[...]

W ARNING! (Continued) • The battery in this vehicle has a vent hose that should not be disconnected and should only be replaced with a battery of the same type (vented). CAUTION! • It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative [...]

W ARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Refer to Section 3 of the W arranty Information B[...]

attention should also be given to hood latching compo- nents to ensure pr oper function. When performing other underhood services, the hood latch, r elease mechanism and safety catch should be cleaned and lubricated. The external lock cylinders should be lubricated twice a year , preferably in the Fall and Spring. Apply a small amount of a high qua[...]

When refilling the washer fluid r eservoir , apply some washer fluid to a cloth or towel and wipe the wiper blades clean. This will help blade performance. T o prevent fr eeze-up of your windshield washer system in cold weather , select a solution or mixture that meets or exceeds the temperature range of your climate. This rating information can be[...]

W ARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. T o avoid breathing CO, refer to “Exhaust Gas” under “Safety T ips” in Section 2. CAUTION! The catalytic converter requires the use of unleaded fuel only . Leade[...]

NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. W ARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your vehicle in areas where your e[...]

Cooling System W ARNING! • When working near the radiator cooling fan, dis- connect the fan motor lead or turn the ignition switch to the LOCK position. The fan is tempera- ture controlled and can start at any time the ignition switch is in the ON position. • Y ou or others can be badly burned by hot coolant or steam from your radiator . If you[...]

Cooling System — Drain, Flush, and Refill If the engine coolant (antifreeze) is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner . Follow with a thorough rinsing to remove all deposits and chemicals. Pr operly dispose of old engine coolant (antifreeze) solution. Refer to the “Maintenanc[...]

CAUTION! (Continued) • This vehicle has not been designed for use with propylene glycol-based engine coolant (anti- freeze). Use of propylene glycol-based engine coolant (antifreeze) is not recommended. Adding Coolant Y our vehicle has been built with an improved engine coolant (antifreeze) that allows extended maintenance intervals. This engine [...]

NOTE: Mixing engine coolant (antifreeze) types will decrease the life of the engine coolant (antifr eeze) and will requir e more fr equent engine coolant (antifreeze) changes. Cooling System Pressure Cap The cap must be fully tightened to prevent loss of engine coolant (antifreeze), and to ensur e that engine coolant (antifreeze) will r eturn to th[...]

rules for your community . T o prevent ingestion by ani- mals or children, do not stor e ethylene glycol-based engine coolant (antifreeze) in open containers or allow it to remain in puddles on the gr ound. If ingested by a child or pet, seek emergency assistance immediately . Clean up any ground spills immediately . Coolant Level The coolant bottl[...]

• Do not overfill the coolant recovery bottle. • Check engine coolant (antifreeze) fr eeze point in the radiator and in the coolant recovery bottle. If engine coolant (antifreeze) needs to be added, contents of coolant recovery bottle must also be pr otected against freezing. • If frequent engine coolant (antifr eeze) additions are requir ed,[...]

W ARNING! Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear , and possible brake damage. Y ou would not have your full braking capacity in an emergency . Master Cylinder - Brake Fluid Level Check Ch[...]

W ARNING! • Use of a brake fluid that may have a lower initial boiling point, or is unidentified as to specification, or which may occur by leaving the top of your master cylinder reservoir uncovered or the top off of the brake fluid bottle off, allowing it to absorb moisture may result in sudden brake failure dur- ing hard prolonged braking. Y o[...]

Clutch Hydraulic System — Manual T ransmission (If Equipped) The clutch hydraulic system is fed by a segregated volume of fluid within the brake system master cylinder reservoir . In the event of leakage or wear , use only the manufacturer’s r ecommended brake fluid. Refer to “Flu- ids, Lubricants, and Genuine Parts” in this section for the[...]

Automatic T ransmission — If Equipped Fluid Level Check Regular automatic transmission fluid level checks are not requir ed. For this reason, the dipstick is omitted. If you notice fluid loss or gear shift malfunction, have your authorized dealer check the transmission fluid level. CAUTION! • Using a transmission fluid other than the manu- fact[...]

Selection of Lubricant It is important that the proper lubricant is used in the transmission to assure optimum transmission perfor - mance. Use only manufacturer ’s recommended transmis- sion fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for the correct fluid type. It is important that the transmission fluid be maint[...]

Appearance Care and Protection from Corrosion Protection of Body and Paint from Corrosion V ehicle body care requir ements vary according to geo- graphic locations and usage. Chemicals that make roads passable in snow and ice, and chemicals that are sprayed on trees and r oad surfaces during other seasons, are highly corrosive to the metal in your [...]

• Use a high quality cleaner wax, such as MOP AR 威 Cleaner W ax to remove r oad film, stains and to protect your paint finish. T ake care never to scratch the paint. • A void using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. CAUTION! Do not use abrasive or strong cleaning materials such as st[...]

• Use MOP AR 威 T ouch Up Paint or equivalent on scratches as soon as possible. Y our authorized dealer has touch up paint to match the color of your vehicle. Wheel and Wheel T rim Care All wheels and wheel trim, especially aluminum and chrome-plated wheels should be cleaned r egularly with a mild soap and water to prevent corr osion. T o remove[...]

Interior Care Use MOP AR 威 Fabric Cleaner or equivalent to clean fabric upholstery and MOP AR 威 Carpet Cleaner for carpeting. Interior T rim should be cleaned starting with a damp cloth, or MOP AR 威 Satin Select. Do not use harsh cleaners or Armor All 威 . Use MOP AR 威 T otal Clean to clean vinyl upholstery . MOP AR 威 T otal Clean is spe[...]

Do not use abrasive cleaning components, solvents, steel wool or other aggressive material to clean the lenses. Glass Surfaces All glass surfaces should be cleaned on a regular basis with MOP AR 威 Glass Cleaner or any commercial household-type glass cleaner . Never use an abrasive type cleaner . Use caution when cleaning the inside rear win- dow [...]

NOTE: The cupholder cannot be removed. FUSES Integrated Power Module (IPM) The Integrated Power Module (IPM) is located in the engine compartment. This module contains fuses and relays. Integrated Power Module 400 MAINT AINING YOUR VEHICLE[...]

CAUTION! • When installing the integrated power module cover , it is important to ensure the cover is prop- erly positioned and fully latched. Failure to do so may allow water to get into the integrated power module and possibly result in an electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having the [...]

Cavity Car- tridge Fuse Mini- Fuse Description 10 30 Amp Pink — W indshield W iper 1 1 30 Amp Pink — Anti-Lock Brake System (ABS) V alves 12 40 Amp Green — Radiator Fan Lo/High 13 50 Amp Red — Anti-Lock Brake System (ABS) Pump Motor 1 4——— 15 50 Amp Red — Radiator Fan Cavity Car- tridge Fuse Mini- Fuse Description 1 6——— 1 7?[...]

Rear Power Distribution Center There is also a power distribution center located in the trunk under the spar e tire access panel. This center contains fuses and relays. Access Panel Rear Power Distribution Center 7 MAINT AINING YOUR VEHICLE 403[...]

CAUTION! • When installing the power distribution center cover , it is important to ensure the cover is prop- erly positioned and fully latched. Failure to do so may allow water to get into the power distribution center and possibly result in an electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having [...]

Cavity Car- tridge Fuse Mini- Fuse Description 5 30 Amp Pink — Heated Seats - if equipped 6 — 20 Amp Y ellow Fuel Pump 7 — 15 Amp Blue Sub Amp - if equipped 8 — 15 Amp Blue Diagnostic Link Connec- tor (DLC)/W ireless Con- trol Module (WCM)/ W ireless Ignition Node (WIN) 9 — 20 Amp Y ellow Power Outlet 1 0——— 11 * ——— 12 * —?[...]

Cavity Car- tridge Fuse Mini- Fuse Description 2 3——— 2 4——— 2 5——— 2 6——— 27 — 10 Amp Red Occupant Restraint Con- troller (ORC) 28 — 10 Amp Red Ignition Run 29 — 5 Amp Orange Cluster/Electronic Sta- bility Program (ESP)/ Powertrain Control Module (PCM)/STOP LIGHT Switch 30 — 10 Amp Red Door Modules/Power Mirrors/Ste[...]

Cavity Car- tridge Fuse Mini- Fuse Description 39 — 10 Amp Red Heated Mirrors - if equipped 40 — 5 Amp Orange Auto Inside Rearview Mirror/Heated Seats - if equipped/Switch Bank 4 1——— 42 30 Amp Pink — Front Blower Motor 43 30 Amp Pink — Rear W indow Defroster 44 20 Amp Blue — Amplifier/Sunroof - if equipped * Cavities 1 1, 12, and 1[...]

REPLACEMENT LIGHT BULBS LIGHT BULBS — Interior Bulb Number Rear Courtesy/Reading Lamps ............. W 5 W Rear Compartment (T runk) Lamp ............. 5 6 2 Overhead Console Reading Lamps ............ 5 7 8 V isor V anity Lamps ..................... A6220 Glove Box Lamp ......................... 1 9 4 Door Courtesy .......................... 5 6[...]

BULB REPLACEMENT Low Beam Headlamp, High Beam Headlamp, Park/T urn Lamp — Models with Halogen Headlamps — If Equipped See your authorized dealer for bulb replacement. Low Beam Headlamp, High Beam Headlamp, and Park/T urn Lamp — Models with High Intensity Discharge (HID) Headlamps — If Equipped HID Headlamps The headlamps are a type of high [...]

NOTE: • If a screwdriver is used, make sur e a soft material is placed between the vehicle body and tool so not to scratch the paint. 2. Rotate the bulb’s socket counter clockwise, and remove the bulb and socket assembly from the housing. 3. Pull the bulb out of the socket and insert the r eplace- ment bulb. 4. Install the bulb and socket assem[...]

3. Remove the fasteners fr om the back of the tail lamp assembly . 4. Pull back the trunk liner . 5. Remove the r emaining fasteners from the back of the tail lamp assembly . 6. Pull the tail lamp assembly clear fr om the vehicle to access the bulbs. 7. Push the electrical connector locking tab to the side. 8. Disconnect the electrical connector . [...]

10. Disconnect the bulb fr om the socket assembly and install the replacement bulb. 1 1. Reinstall the bulb and socket assembly into the tail lamp assembly , and then turn it clockwise. 12. Reinstall the tail lamp assembly , fasteners, electrical connector , and trunk liner . 13. Reinstall tail lamp r etainer . 14. Close the trunk. Center T ail/Bac[...]

Center High-Mounted Stop Lamp (CHMSL) The CHMSL uses LED lamps that are not serviceable separately . The CHMSL must be r eplaced as an assembly , see your authorized dealer . License Lamp 1. Remove the scr ews securing the lamp to the rear fascia. 2. Remove the bulb and socket assembly . 3. Disconnect the bulb fr om the socket assembly and install [...]

FLUIDS AND CAP ACITIES U.S. Metric Fuel (Approximate) 3.5 Liter Engine 18 Gallons 68 Liters 5.7 Liter Engine 19 Gallons 72 Liters Engine Oil with Filter 3.5 Liter Engine (SAE 10W -30, API Certified) 6.0 Quarts 5.7 Liters 5.7 Liter Engine (SAE 5W -20, API Certified) 7.0 Quarts 6.6 Liters Cooling System * 3.5 Liter Engine (MOP AR 威 Antifreeze/Coola[...]

FLUIDS, LUBRICANTS, AND GENUINE P ARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant MOP AR 威 Antifreeze/Coolant 5 Y ear/100,000 Mile Formula HOA T (Hy- brid Organic Additive T echnology) or equivalent. Engine Oil (3.5L Engine) Use API Certified SAE 10W -30 Engine Oil, meeting the requir ements of Chrysler Material Standard MS[...]

Chassis Component Fluid, Lubricant, or Genuine Part Manual T ransmission MOP AR 威 A TF+4 Automatic T ransmission Fluid Automatic T ransmission MOP AR 威 A TF+4 Automatic T ransmission Fluid Brake Master Cylinder MOP AR 威 DOT 3, SAE J1703 or equivalent should be used. If DOT 3 brake fluid is not available, then DOT 4 is acceptable. Use only rec[...]

MAINTENANCE SCHEDULES CONTENTS 䡵 Emission Control System Maintenance ...... 4 1 8 䡵 Maintenance Schedule .................. 4 1 8 ▫ Required Maintenance Intervals .......... 4 2 0 8 M A I N T E N A N C E S C H E D U L E S 417[...]

EMISSION CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type, must be done at the times or mileages specified to ensure the continued proper functioning of the Emission Contr ol System. These, and all other maintenance services in- cluded in this manual, should be done to provide best vehicle performance and reliabilit[...]

NOTE: • The oil change indicator message will not monitor the time since the last oil change. Change your vehicle’s oil if it has been six months since your last oil change, even if the oil change indicator message is NOT illuminated. • Change your engine oil more often if you drive your vehicle off-r oad for an extended period of time. • U[...]

• Check all lights and other electrical items for correct operation. At Each Oil Change • Change the engine oil filter . • Inspect the brake hoses and lines. CAUTION! Failure to perform the required maintenance items may result in damage to the vehicle. Required Maintenance Intervals Refer to the Maintenance Schedules on the following pages f[...]

6,000 Miles (10,000 km) or 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler Dealer 12,000 Miles (20,000 km) or 12 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tir[...]

18,000 Miles (30,000 km) or 18 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Inspect the rear axle fluid. Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler Dealer 24,000 Miles (40,000 km) or 24 Months Maintenance Service Schedule ❏ Change the engine oil and[...]

30,000 Miles (50,000 km) or 30 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Replace the engine air cleaner filter . ❏ Replace the spark plugs (5.7L Engine). ❏ Adjust parking brake on vehicles equipped with four-wheel disc brakes. Odometer Reading Date Repair Order # Dealer Code Sign[...]

42,000 Miles (70,000 km) or 42 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler Dealer 48,000 Miles (80,000 km) or 48 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate t[...]

54,000 Miles (90,000 km) or 54 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Inspect the rear axle fluid. Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler Dealer 60,000 Miles (100,000 km) or 60 Months Maintenance Service Schedule ❏ Change the engine oil an[...]

66,000 Miles (1 10,000 km) or 66 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary . Odometer Reading Date Repair Order # Dealer Code Signature Authorized[...]

78,000 Miles (130,000 km) or 78 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary . Odometer Reading Date Repair Order # Dealer Code Signature Authorized [...]

96,000 Miles (160,000 km) or 96 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Replace the air conditioning filter (if equipped) ❏ Inspect the brake linings; replace if necessary . ❏ Inspect the CV joints. ❏ Inspect exhaust system. ❏ Inspect the front suspension, tie rod ends and [...]

1 14,000 Miles (190,000 km) or 1 14 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary . Odometer Reading Date Repair Order # Dealer Code Signature Authori[...]

126,000 Miles (210,000 km) or 126 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter; replace if necessary . ❏ Inspect the rear axle fluid. Odometer Reading Date Repair Order [...]

144,000 Miles (240,000 km) or 144 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter . ❏ Rotate tires. ❏ Replace the air conditioning filter (if equipped) ❏ Inspect the brake linings; replace if necessary . ❏ Inspect the CV joints. ❏ Inspect exhaust system. ❏ Inspect the rear axle fluid. ❏ Inspect the [...]

† This maintenance is recommended by the manufactur er to the owner , but is not requir ed to maintain emissions warranty . W ARNING! • Y ou can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, [...]

IF YOU NEED CONSUMER ASSIST ANCE CONTENTS 䡵 Suggestions For Obtaining Service For Y our V e h i c l e .............................. 4 3 5 ▫ Prepar e For The Appointment ........... 4 3 5 ▫ Prepar e A List ...................... 4 3 5 ▫ Be Reasonable W ith Requests ............ 4 3 5 䡵 If Y ou Need Assistance ................. 4 3 5 ▫ C[...]

䡵 Department Of T ransportation Uniform T ire Quality Grades ........................ 4 4 0 ▫ T readwear ......................... 4 4 1 ▫ T raction Grades ..................... 4 4 1 ▫ T emperature Grades .................. 4 4 1 434 IF YOU NEED CONSUMER ASSIST ANCE[...]

SUGGESTIONS FOR OBT AINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sur e to have the right papers with you. T ake your warranty folder . All work to be performed may not be covered by the warranty . Discuss additional charges with the service manager . Keep a maintenance log of your vehicle’s[...]

This is why you should always talk to an authorized dealer’s service manager first. Most matters can be re- solved with this process. • If for some reason you ar e still not satisfied, talk to the general manager or owner of the authorized dealer- ship. They want to know if you need assistance. • If an authorized dealership is unable to resol[...]

Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) T o assist customers who have hearing difficulties, the manufacturer has installed special TDD (T elecommuni- cation Devices for the Deaf) equipment at its Customer Center . Any hearing or speech impaired customer , who has access to a TDD or a conventional teletypewriter (TTY) in the[...]

W ARNING! Engine exhaust, some of its constituents, and certain vehicle components contain, or emit, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain prod- ucts of component wear contain, or emit, chemicals known to the State of Cal[...]

T o contact NHTSA, you may either call the Auto Safety Hotline toll free at 1–888–327–4236 (TTY : 1–800–424– 9153), or go to http://www .safercar .gov; or write to: Administrator , NHTSA, 1200 New Jersey A venue, SE., W est Building, W ashington, D.C. 20590. Y ou can also obtain other information about motor vehicle safety from http://w[...]

• Diagnostic Procedure Manuals Diagnostic Procedur e Manuals are filled with dia- grams, charts and detailed illustrations. These practi- cal manuals make it easy for students and technicians to find and fix problems on computer -controlled ve- hicle systems and features. They show exactly how to find and correct pr oblems the first time, using s[...]

T readwear The T readwear grade is a comparative rating, based on the wear rate of the tire when tested under contr olled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100. The relative performance of tir es depends upon the actual[...]

V ehicle Safety Standard No. 109. Grades B and A repre- sent higher levels of performance on the laboratory test wheel, than the minimum requir ed by law . W ARNING! The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, under-inflation, or excessive load- ing, either separately [...]

INDEX 10 443[...]

About Y our Brakes .................... 274,277 ABS (Anti-Lock Brake System) ............ 277,280 Adding Engine Coolant (Antifreeze) .......... 3 8 6 Adding Fuel ........................... 3 2 1 Adding W asher Fluid ..................... 3 8 0 Additives, Fuel ......................... 3 1 9 Air Cleaner , Engine (Engine Air Cleaner Filter) . . . 37[...]

Automatic Door Locks ..................... 3 0 Automatic Headlights .................... 1 2 0 Automatic Oil Change Indicator ............. 1 6 2 Automatic T ransaxle Special Additives ...................... 3 9 4 Automatic T ransmission ............. 259,264,393 Adding Fluid ...................... 393,416 Autostick ............................ 2 6[...]

Parking ............................. 2 7 4 W arning Light ..................... 163,277 Brakes ............................. 277,389 Brake/T ransmission Interlock ............... 2 5 7 Break-In Recommendations, New V ehicle ........ 6 6 Brightness, Interior Lights .................. 1 2 4 Bulb Replacement ..................... 408,409 B u l b s , [...]

Compact Disc (CD) Maintenance ............. 2 2 9 Compact Spare T ire ...................... 3 0 0 Compass .............................. 1 7 5 Compass Calibration ..................... 1 7 6 Compass V ariance ....................... 1 7 6 Computer , T rip/T ravel .................... 1 7 2 Connector U C I ................................ 2 1 7 Uni[...]

Defroster , Rear W indow ................... 1 4 7 Defroster , W indshield ................ 6 9 , 232,233 Delay (Intermittent) W ipers ................. 1 2 5 Diagnostic System, Onboard ................ 3 6 8 Dimmer Switch, Headlight ................. 1 2 3 Dipsticks Oil (Engine) .......................... 3 7 2 Power Steering .....................[...]

Emission Control System Maintenance ...... 369,418 Engine ............................ 366,367 Air Cleaner .......................... 3 7 6 Block Heater ......................... 2 5 0 Break-In Recommendations ................ 6 6 Checking Oil Level ..................... 3 7 2 Compartment ...................... 366,367 Coolant (Antifreeze) ........[...]

Filters Air Cleaner .......................... 3 7 6 Air Conditioning ...................... 2 3 6 Engine Oil ........................ 375,415 Engine Oil Disposal .................... 3 7 5 Flashers Hazard W arning ....................... 3 3 8 T urn Signal ...................... 6 9 , 122,158 Flash-T o-Pass ........................... 1 2 3 Flat T[...]

Saver Mode .......................... 1 7 2 Specifications ......................... 4 1 5 T ank Capacity ........................ 4 1 4 Fuel Optimizer ......................... 1 7 2 Fuel Saver ............................. 1 7 2 Fuel System Caution ..................... 3 2 2 F u e l i n g ............................... 3 2 1 Fuses .............[...]

Cleaning ............................ 3 9 8 D e l a y .............................. 1 2 0 High Beam/Low Beam Select Switch ........ 1 2 3 Lights On Reminder .................... 1 2 1 On W ith W ipers .................... 120,126 Passing ............................. 1 2 3 S w i t c h .............................. 1 1 9 T i m e D e l a y ........[...]

Jump Starting .......................... 3 5 6 Key , Programming ........................ 1 6 Key , Replacement ........................ 1 6 Key , Sentry (Immobilizer) ................... 1 4 Key-In Reminder ......................... 1 4 Keyless Entry System ...................... 2 0 Keyless Go ....................... 1 2 , 175,245 Keys ..........[...]

Exterior .............................. 6 9 F o g ............................. 121,160 Hazard W arning Flasher ................. 3 3 8 Headlight Switch ...................... 1 1 9 Headlights ........................ 1 1 9 , 4 0 9 Headlights On Reminder ................. 1 2 1 Headlights On W ith W ipers ............ 120,126 High Beam ............[...]

Auto Unlock .......................... 3 0 Automatic Door ........................ 3 0 Door ................................ 2 8 Power Door ........................... 2 9 Low T ire Pressur e System .................. 3 0 7 Lower Anchors and T ether for CHildren (LA TCH) ..................... 6 0 , 6 2 Lubrication, Body ....................... 3 7 [...]

Multi-Function Control Lever ............... 1 2 2 New V ehicle Break-In Period ................ 6 6 Occupant Restraints ....................... 3 6 Octane Rating, Gasoline (Fuel) ............ 316,415 Odometer .......................... 156,161 T r i p ............................. 156,161 Oil Change Indicator .................. 162,171 Oil Change [...]

Passing Light ........................... 1 2 3 Personal Settings ........................ 1 7 8 Pets .................................. 6 5 Phone, Cellular .......................... 7 8 Phone, Hands-Free (uconnect 威 ) ............... 7 8 Placard, T ire and Loading Information ......... 2 9 3 Power Brakes .............................. 2 7 7 Dec[...]

Refrigerant ............................ 3 7 9 Release, Hood .......................... 1 1 7 Reminder , Lights On ..................... 1 2 1 Reminder , Seat Belt ....................... 4 2 Remote Control Starting System ........................ 2 6 Remote Keyless Entry (RKE) ................. 2 0 Remote Sound System (Radio) Controls ........ 2 2[...]

Inspection ............................ 6 8 Operating Instructions ................... 3 8 Pretensioners .......................... 4 2 Rear Seat ............................. 3 7 Reminder ............................ 1 6 0 Untwisting Procedur e .................... 4 1 Seats ................................. 1 1 1 Adjustment ......................[...]

Snow Chains (T ire Chains) ................. 3 0 4 Snow T ires ............................ 3 0 6 Sound System Kicker .............................. 2 2 7 Spare T ire .......................... 300,345 Spark Plugs ............................ 4 1 5 Specifications Fuel (Gasoline) ........................ 4 1 5 O i l ................................ [...]

T achometer ............................ 1 5 6 T elescoping Steering Column ............... 1 2 7 T emperature Gauge, Engine Coolant ....... 157,339 T ether Anchor , Child Restraint ............... 6 0 Theft Alarm (Security Alarm) ................ 1 8 Theft System (Security Alarm) ............... 1 8 T ilt Steering Column ..................... 1 2 [...]

T read W ear Indicators ................... 3 0 2 T o Open Hood .......................... 1 1 7 T ongue W eight/T railer W eight .............. 3 2 9 T orque Converter Clutch .................. 2 6 2 T o w i n g ............................... 3 2 5 24-Hour T owing Assistance ................ 9 3 Behind a Motor Home .................. 3 3 6 Disabl[...]

T ransporting Pets ........................ 6 5 T read W ear Indicators .................... 3 0 2 T rip Odometer ....................... 156,161 T runk Lid (Deck Lid) .................... 3 4 , 3 5 T runk Release, Emergency .................. 3 5 T runk Release Remote Control ............... 3 4 T urn Signals ......................... 122,158 UCI [...]

Wheel and Wheel T rim Care ................ 3 9 7 W ind Buffeting ....................... 3 3 , 1 4 2 W indow Airbag (Side Curtain) ............. 4 6 , 5 1 W indow Fogging ........................ 2 3 5 W indows .............................. 3 2 Power ............................... 3 2 W indshield Defroster ................ 6 9 , 232,233 W indshi[...]

INTRODUCTION INTRODUCTION HOW TO USE THIS MANUAL WARNINGSAND CAUTIONS VEHICLE IDENTIFICATION NUMBER VEHICLE MODIFICATIONS/AL TERATIONS THINGS TO KNOW BEFORE STARTING YOUR VEHICLE AWORD ABOUT YOUR KEYS Wireless Ignition Node (WIN)Fob With Integrated KeyIgnition Key RemovalKey-In-Ignition ReminderSENTRY KEY Replacement KeysCustomer Key ProgrammingGen[...]

INST ALLA TION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to pr ovide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained person- nel. The following must be observed during installation. The positive power[...]

2009 CHALL ENGER CHAL LENGER Chrysler LL C 81-226-0916 Third Edition Printed in U.S.A. OWNER ’S MANUAL 2009 147914 Dodge LC22 Challenger.indd 1 9/8/08 3:39:42 PM[...]