Draytek Vigor2110 manual

[...]

Vigor2110 Series User’s Guide ii Vigor2110 Series Broadband Firewall Router User’s Guide Version: 3.0 Firmware Version: V3.3.6 Date: 27/07/2011[...]

Vigor2110 Series User’s Guide iii Copyright Information Copyright Declarations Copyright 2011 All rights reserved. This pub lication contains information that is protected by copyright. No part may be reproduced, transmitted, transcribed, stor ed in a retrieval system, or translated into any language withou t written permission from the copyright[...]

Vigor2110 Series User’s Guide iv European Community Declarations Manufacturer: DrayTek Corp. Address: No. 26, Fu Shing Road, HuKou Town ship, HsinChu Industrial Park, Hsin-Chu, Taiwan 303 Product: Vigor2110 Ser ies Router DrayTek Corp. declares that Vigor2110 Series of ro uters are in compliance with the following essential requirements and other[...]

Vigor2110 Series User’s Guide v T T a a b b l l e e o o f f C C o o n n t t e e n n t t s s 1 Pref ace ............................................................................................................... 1 1.1 Web Conf iguration Bu ttons Explanation ................................................................................. 1 1.2[...]

Vigor2110 Series User’s Guide vi 3.4.1 Dynam ic DNS .............................................................................................................. ... 52 3.4.2 UPnP..................................................................................................................... .......... 54 3.5 V oIP ..........................[...]

Vigor2110 Series User’s Guide vii 4.4.3 Filter Setup ............................................................................................................. ...... 132 4.4.4 DoS Defense .............................................................................................................. .. 140 4.5 Object s Settings ................[...]

Vigor2110 Series User’s Guide viii 4.12.9 AP Di scovery ............................................................................................................ .. 241 4.12.10 Stat ion List ........................................................................................................... ..... 242 4.13 USB App lication ..............[...]

Vigor2110 Series User’s Guide ix T rouble Shoot ing ......................................................................................... 309 6.1 Checking If the Hardware S t atus Is OK or No t.................................................................... 309 6.2 Checking If the Network Connection Settings on Y our Computer Is OK or Not[...]

[...]

Vigor2110 Series User’s Guide 1 1 P P r r e e f f a a c c e e Vigor2110 series is a broadband router. It integrates IP layer QoS, NAT session/bandwidth management to help users control works well with large bandwidth. By adopting hardware-based VPN platform and hardware encryption of AES/DES/3DS, the router increases the performance of VPN greatl[...]

Vigor2110 Series User’s Guide 2 1 1 . . 2 2 L L E E D D I I n n d d i i c c a a t t o o r r s s a a n n d d C C o o n n n n e e c c t t o o r r s s Before you use the Vigor router, please get acquainted with the LED indicators and connectors first. 1 1 . . 2 2 . . 1 1 F F o o r r V V i i g g o o r r 2 2 1 1 1 1 0 0 LED Status Explanation Blinking[...]

Vigor2110 Series User’s Guide 3 Interface Description Factory Reset Restore the default settings. Usage: Tu rn on t he router (ACT LED is blinking). Press the hole and keep for m ore than 5 seconds . When you see t he ACT LED begins to blink rapidly than usual, release th e butto n. Then the router will restart with the factory default con figura[...]

Vigor2110 Series User’s Guide 4 1 1 . . 2 2 . . 2 2 F F o o r r V V i i g g o o r r 2 2 1 1 1 1 0 0 n n LED Status Explanation Blinking The router i s powered on and running normally . ACT (Activity) Off The router is powe red off. On Wireless access point is rea dy. WLAN Blinking It will blink while wireless traffic goes through. On The WAN port[...]

Vigor2110 Series User’s Guide 5 Interface Description Factory Reset Restore the default settings. Usage: Turn on the router (ACT LED is blinking). Press the hole and keep for more than 5 seconds. When y ou see the ACT LED be gins to blink rapidly than usual, release the button. Th en th e router will restart with the factory default configuration[...]

Vigor2110 Series User’s Guide 6 1 1 . . 2 2 . . 3 3 F F o o r r V V i i g g o o r r 2 2 1 1 1 1 0 0 V V n n LED Status Explanation Blinking The router i s powered on and running normally . ACT (Activity) Off The router is powe red off. On Wireless access point is rea dy. WLAN Blinking It will blink while wireless traffic goes through. On The WAN [...]

Vigor2110 Series User’s Guide 7 Interface Description Line Connector for PSTN life line. Phone2/P hone1 Connecter of analog phon e for VoIP com munication . Factory Reset Restore the default settings. Usage: Turn on the router (ACT LED is blinking). Press the hole and keep for more than 5 seconds. When y ou see the ACT LED be gins to blink rapidl[...]

Vigor2110 Series User’s Guide 8 1 1 . . 3 3 H H a a r r d d w w a a r r e e I I n n s s t t a a l l l l a a t t i i o o n n Before starting to configure the router, you have to connect your devices correctly. 1. Connect Line port to land line jack with a RJ-11 cable (Vn model). 2. Connect this device to a modem with a RJ-45 cable. 3. Connect one [...]

Vigor2110 Series User’s Guide 9 S S t t a a n n d d I I n n s s t t a a l l l l a a t t i i o o n n The Vigor2110 must be placed erectly. Therefore you have to install a stand onto the router to make it standing firmly. Please follow the figures listed below to finish the installation. c d e f[...]

Vigor2110 Series User’s Guide 10 1 1 . . 4 4 P P r r i i n n t t e e r r I I n n s s t t a a l l l l a a t t i i o o n n You can install a printer onto the router for shar ing printing. All the PCs connected this router can print documents via the router. The exam ple provided here is made based on Windows XP/2000. For Windows 98/SE/Vista, please[...]

Vigor2110 Series User’s Guide 11 Open File->Add Printer . A welcome dialog will appear. Please click Next . 3. Click Local printer attached to this computer and click Next. 4. In this dialog, choose Create a new port Type of port and use the drop down list to select Standard TCP/IP Port . Click Next .[...]

Vigor2110 Series User’s Guide 12 5. In the following dialog, type 192.168.1.1 (router’s LAN IP) in the field of Printer Name or IP Address and type IP_192.168.1.1 as the port name. Then, click Next . 6. Click Standard and choose Generic Network Card. 7. Then, in the following dialog, click Finish .[...]

Vigor2110 Series User’s Guide 13 8. Now, your system will ask you to choose right na me of the printer t hat you installed onto the router. Such step can make correct driver loaded onto your PC. When you finish the selection, click Next . 9. For the final stage, you need to go back to Control Panel-> Printers and edit the property of the new p[...]

Vigor2110 Series User’s Guide 14 The printer can be used for printing now. Most of the printers with different manufacturers are compatible with vigor router. Note 1: Some printers with the fax/scanning or other additional fun ctions are not supported. If you do not know whether your pr inter is supported or not, please vi sit www.draytek.com to [...]

Vigor2110 Series User’s Guide 15 2 C C o o n n f f i i g g u u r r i i n n g g B B a a s s i i c c S S e e t t t t i i n n g g s s For using the router properly, it is necessar y for you to change the password of web configuration for security and adjust primary basic settings. 2 2 . . 1 1 T T w w o o - - L L e e v v e e l l M M a a n n a a g g e[...]

Vigor2110 Series User’s Guide 16 5. The web page can be logged out according to the chosen condition. The default setting is Auto Logout , which means the web configuration system will logout after 5 m inutes without any operation. Change the setting for your necessity. 2 2 . . 3 3 C C h h a a n n g g i i n n g g P P a a s s s s w w o o r r d d N[...]

Vigor2110 Series User’s Guide 17 Main screen for user mode operation (simple configuration) Note: The home page will change slightly in acco rdance with the type of the router you have. 4. Go to System Maintenance page and choose Administrator Password/User Password . or 5. Enter the login password (the defa ult is blank) on the field of Old Pass[...]

Vigor2110 Series User’s Guide 18 6. Now, the password has been changed. Next time, use the new password to access the Web Configurator for this router. 2 2 . . 4 4 Q Q u u i i c c k k S S t t a a r r t t W W i i z z a a r r d d Notice: Quick Start Wizard for user mode operation is the same as for admin mode operation. If your router can be under [...]

Vigor2110 Series User’s Guide 19 2 2 . . 4 4 . . 1 1 P P P P P P o o E E PPPoE stands for Point-to-Point Protocol over Ethernet . It relies on two widely accepted standards: PPP and Ethernet. It connects users th rough an Ethernet to the Internet with a common broadband medium, such as a single DSL line, wireless device or cable m odem. All the u[...]

Vigor2110 Series User’s Guide 20 Confirm Password Retype the password. Click Next for viewing summary of such connection. Click Finish. Then, the system status of this protocol will be shown. 2 2 . . 4 4 . . 2 2 P P P P T T P P / / L L 2 2 T T P P Click PPTP/L2TP as the protocol. Type in all the information that your ISP provides for this protoco[...]

Vigor2110 Series User’s Guide 21 Click Finish. Then, the system status of this protocol will be shown. 2 2 . . 4 4 . . 3 3 S S t t a a t t i i c c I I P P Click Static IP as the protocol. Type in all the inform ation that your ISP provides for this protocol. After finishing the settings in this page, click Next to see the following page.[...]

Vigor2110 Series User’s Guide 22 Click Finish. Then, the system status of this protocol will be shown. 2 2 . . 4 4 . . 4 4 D D H H C C P P Click DHCP as the protocol. Type in all the information that your ISP provides for this protocol. After finishing the settings in this page, click Next to see the following page.[...]

Vigor2110 Series User’s Guide 23 Click Finish. Then, the system status of this protocol will be shown. 2 2 . . 5 5 S S e e r r v v i i c c e e A A c c t t i i v v a a t t i i o o n n W W i i z z a a r r d d Service Activation Wizard can guide you to set WCF (Web Content Feature) feature with a quick way. Note: There are three ways to activate WCF[...]

Vigor2110 Series User’s Guide 24 2. The screen of Service Activation Wizard will be shown as follows. Choose the one you need and click Next . In this case, we choose to activate free trail edition. Free trial edition : it offers a period of trial for you to get acquainted with WCF function. Formal edition with license key : you can extend the li[...]

Vigor2110 Series User’s Guide 25 4. Setting confirmation page will be displayed as follows, please click Next . 5. Wait for a moment till the following page appears. When such page appears, you can enable or disable these services for your necessity. Then, click Finish. Note: The service will be activated and applied as the default rule configure[...]

Vigor2110 Series User’s Guide 26 Later, if you need to extend the licen se valid time, you can also use the Service Activation Wizard again to reach your goal by clicking the radio bu tton of Formal edition with license key and clicking Next. Check the box of “I have read and accept the above..” and click Next. Follow the on-screen instructio[...]

Vigor2110 Series User’s Guide 27 2 2 . . 6 6 O O n n l l i i n n e e S S t t a a t t u u s s The online status shows the system status, WAN st atus, and other status related to this router within one page. If you select PPPoE/PPPoA as the protocol, you will find out a link of Dial PPPoE or Drop PPPoE in the Online Status web page. Online status f[...]

Vigor2110 Series User’s Guide 28 2 2 . . 7 7 S S a a v v i i n n g g C C o o n n f f i i g g u u r r a a t t i i o o n n Each time you click OK on the web page for saving the configurati on, you can find messages showing the system interaction with you. Ready indicates the system is ready for you to input settings. Settings Saved means your setti[...]

Vigor2110 Series User’s Guide 29 3 U U s s e e r r M M o o d d e e O O p p e e r r a a t t i i o o n n This chapter will guide users to execute simple configuration t hrough u ser mode operation. As for other examples of application, please refer to chapter 5. 1. Open a web browser on your PC and type http://192. 168.1.1. The window will ask for [...]

Vigor2110 Series User’s Guide 30 From 10.0.0.0 to 10.255.255.255 From 172.16.0.0 to 172.31.255.255 From 192.168.0.0 to 192.168.255.255 W W h h a a t t a a r r e e P P u u b b l l i i c c I I P P A A d d d d r r e e s s s s a a n n d d P P r r i i v v a a t t e e I I P P A A d d d d r r e e s s s s As the router plays a role to manage and further [...]

Vigor2110 Series User’s Guide 31 Modem will be listed on DrayTek web site. Pl ease visit www.draytek.com for more detailed information. Below shows the menu items for Internet Access . 3 3 . . 1 1 . . 2 2 P P P P P P o o E E To choose PPPoE as the accessing protocol of the internet, please select PPPoE from the Internet Access menu. The following[...]

Vigor2110 Series User’s Guide 32 Ping IP – If you choose Ping Detect as detection mode, you have to type IP address in this field for pinging. TTL (Time to Live) – Displays value for your reference. TTL value is set by telnet command. Enable Bridge Mode Check this box to invoke the Bridge function for WA N connection. The router will work as [...]

Vigor2110 Series User’s Guide 33 PPP Authentication – Select PAP only or PAP or CHAP for PPP. WAN Connection Detection - Such function allows you to verify whether network connection is alive or not through ARP Detect or Ping Detect. Mode – Choose ARP Detect or Ping Detect for the system to execute for WAN detection. Ping IP – If you choose[...]

Vigor2110 Series User’s Guide 34 specify another MAC address by typing on the boxes of MAC Address for the router. Specify a MAC Address – Type the MAC address f or the router manually. WAN physical type Choose Auto negotiation as the physical type for your router. After finishing all the settings here, please click OK to activate them. 3 3 . .[...]

Vigor2110 Series User’s Guide 35 Access Control Click Enable for activating this function. If you click Disable , this function will be closed and all the settings that you adjusted in this page will be invalid. Keep WAN Connection Normally, this function is designed for Dynamic IP environm ents because some ISPs will drop connections if there is[...]

Vigor2110 Series User’s Guide 36 RIP Protocol Routing Information Protocol is abbreviated as RIP （ RFC1058 ） specifying how routers exchange routing tables information. Click Enable RIP for activating this function. Enable Bridge Mode Check this box to invoke the Bridge function for WA N connection. The router will work as a bridge modem. WAN[...]

Vigor2110 Series User’s Guide 37 WAN Connection Detection - Such function allows you to verify whether network connection is alive or not through ARP Detect or Ping Detect. Mode – Choose ARP Detect or Ping Detect for the system to execute for WAN detection. Ping IP – If you choose Ping Detect as detection mode, you have to type IP address in [...]

Vigor2110 Series User’s Guide 38 need to click the Specify a MAC Address and enter the MAC address in the MAC Address field. DNS Server IP Address Type in the primary IP address for the router if you want to use Static IP mode. If necessary, type in secondary IP address for necessity in the future. 3 3 . . 1 1 . . 4 4 P P P P T T P P / / L L 2 2 [...]

Vigor2110 Series User’s Guide 39 PPP Client Mode - Click Enable to activate this mode for WAN2. SIM PIN code - Type PIN code of the SIM card that will be used to access Internet. Modem Initial String - Such value is used to initialize USB modem. Please use the default value. If you have any question, please contact to your ISP. APN Name - APN(Acc[...]

Vigor2110 Series User’s Guide 40 Default – Click this button to reset to factory setting. PPP Setup PPP Authentication - Select PAP only or PAP or CHAP for PPP. Idle Timeout - Set the timeout for breaking down the Internet after passing through the time without any action. IP Address Assignment Method(IPCP) Fixed IP - Usually ISP dynamically as[...]

Vigor2110 Series User’s Guide 41 3 3 . . 2 2 L L A A N N Local Area Network (LAN) is a group of subnets regulated and ruled by router . The design of network structure is related to what type of public IP addresses coming from your ISP . 3 3 . . 2 2 . . 1 1 B B a a s s i i c c s s o o f f L L A A N N The most generic function of V igor router is [...]

Vigor2110 Series User’s Guide 42 W W h h a a t t i i s s R R o o u u t t i i n n g g I I n n f f o o r r m m a a t t i i o o n n P P r r o o t t o o c c o o l l ( ( R R I I P P ) ) V igor router will exchange routing informati on with neighboring routers using the RIP to accomplish IP routing. This allows users to cha nge the information of the r[...]

Vigor2110 Series User’s Guide 43 2 nd IP Address T y pe in secondary IP address for connecting to a subnet. (Default: 192.168.2.1/ 24) 2 nd Subnet Mask An address code that determines the size of the network. (Default: 255.255.255.0/ 24) 2 nd DHCP Se rver Y ou can configure the router to serve as a DHCP server for the 2nd subnet. S tart IP Addres[...]

Vigor2110 Series User’s Guide 44 DHCP Server Configuration DHCP stands for Dynamic Host Configuration Protoc ol. The router by factory default acts a DHCP server for your network so it automatically dispatch related IP settings to any local user configured as a DHCP client. It is highly recommended that you leave the router enabled as a DHCP serv[...]

Vigor2110 Series User’s Guide 45 If both the Primary IP and Secondary IP Address fields are left empty , the router will assign its own IP address to local users as a DNS proxy server and maintain a DNS cache. If the IP address of a domain name is already in the DNS cache, the router will resolve the domain name immediately . Otherwise, the route[...]

Vigor2110 Series User’s Guide 46 3 3 . . 3 3 . . 1 1 P P o o r r t t R R e e d d i i r r e e c c t t i i o o n n Port Redirection is usually set up for server related service inside the local network (LAN), such as web servers, FTP servers, E-mail servers etc. Most of the case, you need a public IP address for each server and this public IP addre[...]

Vigor2110 Series User’s Guide 47 Press any number under Index to access into next page for configuring port redirection. Enable Check this box to enable su ch port redirection setting. Mode Two options (Single and Range) are provided here for you to cho ose. To set a range for the specific service, select Range . In Range mode, if the public port[...]

Vigor2110 Series User’s Guide 48 3 3 . . 3 3 . . 2 2 D D M M Z Z H H o o s s t t As mentioned above, Port Redirection can redirect incoming TCP/UDP or othe r traffic on particular ports to the specific private IP address/port of host in the LAN. However, other IP protocols, for example Protocols 50 (ESP) and 51 (A H), do not travel on a fixed por[...]

Vigor2110 Series User’s Guide 49 If you previously have set up WAN Alias for PPPoE or Static or Dynamic IP mode , you will find them in Aux. WAN IP for your selection. Enable Check to enable the DMZ Host function. Private IP Enter the private IP address of the DMZ host, or click Choose PC to select one. Choose PC Click this button and then a wind[...]

Vigor2110 Series User’s Guide 50 3 3 . . 3 3 . . 3 3 O O p p e e n n P P o o r r t t s s Open Ports allows you to open a range of ports for the traffic of special applications. Common application of Open Ports includes P2 P application (e.g., BT, KaZaA, Gnutella, WinMX, eMule and others), Internet Camera etc. Ensure that you keep the application [...]

Vigor2110 Series User’s Guide 51 Enable Open Ports Check to enable this entry. Comment Make a name for the defined network application/service. WAN IP Specify the WAN IP address that w ill be used for this entry. This setting is available when WAN IP Alias is configured. Local Computer Enter the private IP address of the local host or click Choos[...]

Vigor2110 Series User’s Guide 52 3 3 . . 4 4 A A p p p p l l i i c c a a t t i i o o n n s s Below shows the menu items for Applications. 3 3 . . 4 4 . . 1 1 D D y y n n a a m m i i c c D D N N S S The ISP often provides you with a dynamic IP address when you c onnect to the Internet via your ISP. It means that the public IP address assigned to y[...]

Vigor2110 Series User’s Guide 53 View Log Display DDNS log status. Force Update Force the router updates its information to DDNS server. 3. Select Index number 1 to add an account for the router. Check Enable Dynamic DNS Account , and choose correct Service Provider: dyn dns.org, type the registered hostname: hostname and domain name suffix: dynd[...]

Vigor2110 Series User’s Guide 54 3 3 . . 4 4 . . 2 2 U U P P n n P P The UPnP (Universal Plug and Play) protocol is supported to bring to network connected devices the ease of installation and configurati on which is already available for directly connected PC peripherals with the existing Windows 'Plug and Play' system. For NAT routers[...]

Vigor2110 Series User’s Guide 55 The reminder as regards concern about Firewall and UPnP Can't work with Firewall Software Enabling firewall applications on your P C may cause the UPnP function not working properly. This is because these applicati ons will block the accessing ability of some network ports. Security Considerations Activating [...]

Vigor2110 Series User’s Guide 56 while the MGCP protocol uses client-server architecture, the calling scenario being very similar to the current PSTN/ISDN network. After a call is setup, the voice streams transmit via RTP (Real-Time Transport Protocol). Different codecs (methods to compress and en code the voice) can be embedded into RTP packets.[...]

Vigor2110 Series User’s Guide 57 Our Vigor V models firstly apply efficient codecs designed to make the best use of available bandwidth, but Vigor V models also equip with autom atic QoS assurance. QoS Assurance assists to assign high priori ty to voice traffic via Internet. You will always have the required inboun d and outbound bandwidth that i[...]

Vigor2110 Series User’s Guide 58 Click any index number to display the dial plan setup page. Enable Click this to enable this entry. Phone Number The speed-dial number of this index. This can be any number you choose, using digits 0- 9 and * . Display Name The Caller-ID that you want to be displayed on your friend’s screen. This let your friend[...]

Vigor2110 Series User’s Guide 59 the same SIP server, sometimes, the VoIP phone call connection may not succeed. By using the specified dial out account, the successful connection can be assured. Loop through The selection should be as the following: Backup Phone Number When the VoIP phone is obstructs or the Internet breaks down for some reasons[...]

Vigor2110 Series User’s Guide 60 D D i i g g i i t t M M a a p p For the convenience of user, this page allows users to edit prefix number for the SIP account with adding number, stripping number or replacing number. It is used to help user having a quick and easy way to dial out through VoIP interface. Enable Check this box to invoke this settin[...]

Vigor2110 Series User’s Guide 61 will be changed to “886311111 11” and sent to SIP server. OP Number The front number you type here is the first part of the account number that you want to execute special function (according to the chosen mode) by using the prefix number. Min Len Set the minimal length of the dial number for appl ying the pre[...]

Vigor2110 Series User’s Guide 62 Click any index number to display the dial plan setup page. Enable Click this to enable this entry. Call Direction Determine the direction for the phone call, IN – incoming call, OUT-outgoing call, IN & OUT – both incoming and outgoing calls. Barring Type Determine the type of the VoIP phone call, URI/URL [...]

Vigor2110 Series User’s Guide 63 For Block Unknown Domain – this function can block incomi ng calls (through Phone port) from unrecognized domain that is not specified in SIP accounts. For Block IP Address – this function can block incoming calls (through Phone port) com ing from IP address. R R e e g g i i o o n n a a l l This page allows yo[...]

Vigor2110 Series User’s Guide 64 Last Call Return [Miss] Sometimes, people might miss some phone calls. Please dial number typed in this field to know where the last phone call comes from and call back to that one. Last Call Return [In] You have finished an incoming phone call, however you want to call back again for some reason. Please dial numb[...]

Vigor2110 Series User’s Guide 65 Block Last Calls [Act] Dial the number typed in this field to bl ock the last incoming phone call. P P S S T T N N S S e e t t u u p p Some emergency phone (e.g., 911) or special phone cannot be dialed out b y using VoIP and can be called out through PSTN line only. To solv e this problem, this page allows you to [...]

Vigor2110 Series User’s Guide 66 3 3 . . 5 5 . . 2 2 S S I I P P A A c c c c o o u u n n t t s s In this section, you set up your own SIP setti ngs. When you apply for an account, your SIP service provider will give you an Account Name or user name, SIP Registrar, Proxy, and Domain name . (The last three might be the same in some case). Then y ou[...]

Vigor2110 Series User’s Guide 67 Click any index number to configure the SIP account. Profile Name Assign a name for this profile for identifying. You can t ype similar name with the domain. For example, if the domain name is draytel.org , then you might set draytel-1 in this field. Register via If you want to make VoIP call without register pers[...]

Vigor2110 Series User’s Guide 68 Account Number/Name Enter your account name of SIP Address, e.g. every text before @. Authentication ID Check the box to invoke this function and enter the name or number used for SIP Authorization with SIP Registrar. If this setting value is the same as Account Name, it is not necessary for you to check the box a[...]

Vigor2110 Series User’s Guide 69 Only the selected Codec will be applied. Single Codec – If the box is checked, only the selected Codec will be applied. Packet Size The amount of data contained in a single packet. The default value is 20 ms, which means the data packet will contain 20 ms voice information. Voice Active Detector This function ca[...]

Vigor2110 Series User’s Guide 70 3 3 . . 5 5 . . 3 3 P P h h o o n n e e S S e e t t t t i i n n g g s s This page allows user to set phone settings fo r Phone 1 and Phone 2 respectively. However, it changes slightly according to different model you have. Phone List Port – t here are two phone ports provided here for you to configure. Phone1/Ph[...]

Vigor2110 Series User’s Guide 71 RTP TOS – It decides the level of VoIP package. Use the drop down list to choose any one of them. D D e e t t a a i i l l e e d d S S e e t t t t i i n n g g s s f f o o r r P P h h o o n n e e P P o o r r t t Click the number link for Phone port, you can access into t he following page for configuring Phone set[...]

Vigor2110 Series User’s Guide 72 Call Forwarding There are four options for you to choose. Disable is to close call forwarding function. Always means all the incoming calls will be forwarded into SIP URL without any reason. Busy means the incoming calls will be forwarded into SIP URL only when the local system is busy. No Answer means if the inco[...]

Vigor2110 Series User’s Guide 73 Region Select the proper region which you are located. The common settings of Caller ID Type , Dial tone , Ringing tone , Busy tone and Congestion tone will be shown automatically on the page. If you cannot find out a suitable one, please choose User Defined and fill out the corresponding values for dial tone, rin[...]

Vigor2110 Series User’s Guide 74 recommended for you to use the default settings for VoIP communication. Volume Gain Mic Gain (1-10)/Speaker Gain (1-10) - Adjust the volume of microphone and speaker by entering number from 1- 10. The larger of the number, the louder the volume is. MISC Dial Tone Power Leve l - This setting is used to adjust the l[...]

Vigor2110 Series User’s Guide 75 3 3 . . 5 5 . . 4 4 S S t t a a t t u u s s From this page, you can find codec, connection and ot her important call status for each port. Refresh Seconds Specify the interval of refresh time to obtain the latest VoIP calling information. The information will update immediately when the Refresh button is clicked. [...]

Vigor2110 Series User’s Guide 76 Rx Losts Total number of lost packets during this connection session. Rx Jitter The jitter of received voice packets. In Calls Accumulation for the times of in call. Out Calls Accumulation for the times of out call. Miss Calls Accu mulation for the times of missing call. Speaker Gain The volume of present call. Lo[...]

Vigor2110 Series User’s Guide 77 S S e e c c u u r r i i t t y y O O v v e e r r v v i i e e w w Real-time Hardware Encryption: Vigor Router is equipped with a hardware AES encryption engine so it can apply the highest prote ction to your data without influencing user experience. Complete Security Standard Selection: To ensure the security and pr[...]

Vigor2110 Series User’s Guide 78 3 3 . . 6 6 . . 2 2 G G e e n n e e r r a a l l S S e e t t u u p p By clicking the General Settings , a new web page will appear so that you could configure the SSID and the wireless channel. Please refer to the following figure for more information. Enable Wireless LAN Check the box to enable wireless function. [...]

Vigor2110 Series User’s Guide 79 Packet-OVERDRIVE This feature can enhance the performance in data transmission about 40%* m ore (by checking Tx Burs t). It is active only when both sides of Access Point and Station (in wireless client) invoke this function at the same time. That is, the wireless client must support this feature and invoke the fu[...]

Vigor2110 Series User’s Guide 80 Long Preamble This option is to define the length of the sync field in an 802.11 packet. Most modern wireless network uses short preamble with 56 bit sync field instead of long pream ble with 128 bit sync field. However, some original 11b wireless network devices only support long preamble. Check it to use Long Pr[...]

Vigor2110 Series User’s Guide 81 WPA The WPA encrypts each frame transmitted from the radio using the key, which either PSK (Pre-Shared Key) entered manually in this field below or automatically negotiated via 802.1x authentication. Either 8~63 ASCII characters, such as 012345678(or 64 Hexadecimal digits leading by 0x, such as "0x321253abcde[...]

Vigor2110 Series User’s Guide 82 Enable Access Control Select to enable the MAC Address access control feature. Policy Select to enable any one of the following policy. Choose Activate MAC address filter to type in the MAC addresses for other clients in the network manually. Choose Isolate WLAN from LAN will separate all the WLAN stations from LA[...]

Vigor2110 Series User’s Guide 83 3 3 . . 6 6 . . 5 5 S S t t a a t t i i o o n n L L i i s s t t Station List provides the knowledge of connecting wire less clients now along with its status code. There is a code summary belo w for explanation. For convenient Access C ontrol , you can select a WLAN station and click Add to Access Control below. R[...]

Vigor2110 Series User’s Guide 84 3 3 . . 7 7 U U S S B B A A p p p p l l i i c c a a t t i i o o n n USB diskette can be regarded as a server. By way of Vigor router, clients on LAN can access, write and read data stored in USB diskette. After setting the configuration in USB Application , you can type the IP address of the Vigor router and us er[...]

Vigor2110 Series User’s Guide 85 Default Charset is for English based file name. For Simplified Chinese file/directory names, please choose GB2312; for Traditional Chinese file/directory names, choose BIG5. Samba Service Settings Click Enable to invoke samba service via the router. Access Mode LAN Only – Users coming from internet cannot connec[...]

Vigor2110 Series User’s Guide 86 FTP/Samba User Enable – Click this button to activate this profile (account) for FTP service or Samba User service. Later, the user can use the username specified in this page to login into FTP server. Disable – Click this button to disable such profile. Username Type the username for FTP/Sa mba users for acce[...]

Vigor2110 Series User’s Guide 87 Access Rule It determines the authority for such profile. Any user, who uses such profile for accessing into USB diskette, must follow the rule specified here. File – Check the items (Read, Write and Delete) for such profile. Directory –Check the items (List, Create and Re move) for such profile. Before you cl[...]

Vigor2110 Series User’s Guide 88 3 3 . . 7 7 . . 3 3 F F i i l l e e E E x x p p l l o o r r e e r r To review the content of USB diskette via USB port of the router, please open USB Application Explorer to browse the files. Refresh Click this icon to refresh files list. Back Click this icon to return to the upper directory. Create Click this ico[...]

Vigor2110 Series User’s Guide 89 3 3 . . 7 7 . . 4 4 U U S S B B D D i i s s k k S S t t a a t t u u s s This page is to monitor the status for the users who accessing into FTP or Samba server (USB diskette) via the Vigor router. If you want to remove the diskette from USB port in router, please click Disconnect USB Disk first. And then, remove t[...]

Vigor2110 Series User’s Guide 90 3 3 . . 8 8 S S y y s s t t e e m m M M a a i i n n t t e e n n a a n n c c e e For the system setup, there are several items that you have to know the way of configuration: Status, Administrator Password, Configuration Backup, Syslog, Time setup, Reboot System, Firmware Upgrade. Below shows the menu items for Sys[...]

Vigor2110 Series User’s Guide 91 Connection Display the connection type. IP Address Display the IP address of the WAN interface. Default Gateway Display the assigned IP address of the default gateway. Wireless LAN------- MAC Address Display the MAC address of the wireless LAN. Frequency Domain It can be Europe (13 usable channels), USA (11 usable[...]

Vigor2110 Series User’s Guide 92 3 3 . . 8 8 . . 3 3 T T i i m m e e a a n n d d D D a a t t e e It allows you to specify where the time of the router should be inquired from. Current System Time Click Inquire Time to get the current time. Use Browser Time Select this option to use the browser time from the remote administrator PC host as router?[...]

Vigor2110 Series User’s Guide 93 Note: When the system pops up Reboot System web page after you configure web settings, please click Reboot Now to reboot your router for ensuring norm al operation and preventing unexpected errors of the router in the future. 3 3 . . 9 9 D D i i a a g g n n o o s s t t i i c c s s Diagnostic Tools provide a useful[...]

Vigor2110 Series User’s Guide 94 3 3 . . 9 9 . . 2 2 T T r r a a f f f f i i c c G G r r a a p p h h Click Diagnostics and click Traffic Graph to pen the web page. Choose WAN1 Bandwidth, Sessions, daily or weekly for viewi ng different traffic graph. Click Refresh to renew the graph at any time. 3 3 . . 9 9 . . 3 3 P P i i n n g g D D i i a a g g[...]

Vigor2110 Series User’s Guide 95 3 3 . . 9 9 . . 4 4 T T r r a a c c e e R R o o u u t t e e Click Diagnostics and click Trace Route to open the web page. This page allows you to trace the routes from router to the host. Simply type the IP address of the host in the box and click Run . The result of route trace will be shown on the screen. Protoc[...]

Vigor2110 Series User’s Guide 96 This page is left blank.[...]

Vigor2110 Series User’s Guide 97 4 A A d d m m i i n n M M o o d d e e O O p p e e r r a a t t i i o o n n This chapter will guide users to execute adva nced (full) configuration thr ough admin mode operation. As for other examples of application, please refer to chapter 5. 1. Open a web browser on your PC and type http://192. 168.1.1. The window[...]

Vigor2110 Series User’s Guide 98 From 10.0.0.0 to 10.255.255.255 From 172.16.0.0 to 172.31.255.255 From 192.168.0.0 to 192.168.255.255 W W h h a a t t a a r r e e P P u u b b l l i i c c I I P P A A d d d d r r e e s s s s a a n n d d P P r r i i v v a a t t e e I I P P A A d d d d r r e e s s s s As the router plays a role to manage and further [...]

Vigor2110 Series User’s Guide 99 4 4 . . 1 1 . . 2 2 P P P P P P o o E E To choose PPPoE as the accessing protocol of the internet, please select PPPoE from the Internet Access menu. The following web page will be shown. Enable/Disable Click Enable for activating this function. If you click Disable , thi s function will be closed and all the sett[...]

Vigor2110 Series User’s Guide 100 WAN Backup Setup Dial Backup Mode - If you install a 3G USB modem on the router, choose the 3G USB Modem to perform WAN backup via USB device. Then, click the 3G USB Modem Backup link to access into the following page for configuring detailed settings. PPP Client Mode - Click Enable to activate this mode for WAN2[...]

Vigor2110 Series User’s Guide 101 Application >> Schedule web page and you can use the number that you have set in that web page. WAN Connection Detection - Such function allows you to verify whether network connection is alive or not through ARP Detect or Ping Detect. Mode – Choose ARP Detect or Ping Detect for the system to execute for [...]

Vigor2110 Series User’s Guide 102 Default MAC Address – You can use Default MAC Address or specify another MAC address by typing on the boxes of MAC Address for the router. Specify a MAC Address – Type the MAC address f or the router manually. WAN physical type Choose Auto negotiation as the physical type for your router. After finishing all [...]

Vigor2110 Series User’s Guide 103 Access Control Click Enable for activating this function. If you click Disable , this function will be closed and all the settings that you adjusted in this page will be invalid. Keep WAN Connection Normally, this function is designed for Dynamic IP environm ents because some ISPs will drop connections if there i[...]

Vigor2110 Series User’s Guide 104 Enable RIP for activating this function. Enable Bridge Mode Check this box to invoke the Bridge function for WA N connection. The router will work as a bridge modem. WAN Backup Setup Dial Backup Mode - If you install a 3G USB modem on the router, choose the 3G USB Modem to perform WAN backup via USB device. Then,[...]

Vigor2110 Series User’s Guide 105 Application >> Schedule web page and you can use the number that you have set in that web page. WAN Connection Detection - Such function allows you to verify whether network connection is alive or not through ARP Detect or Ping Detect. Mode – Choose ARP Detect or Ping Detect for the system to execute for [...]

Vigor2110 Series User’s Guide 106 Specify a MAC Address : Some Cable service providers specify a specific MAC address for access authentication. In such cases y ou need to click the Specify a MAC Address and enter the MAC address in the MAC Address field. DNS Server IP Address Type in the primary IP address for the router if you want to use Stati[...]

Vigor2110 Series User’s Guide 107 4 4 . . 1 1 . . 4 4 P P P P T T P P / / L L 2 2 T T P P To use PPTP/L2TP as the accessing protocol of the internet, please choose PPTP/L2TP from Internet Access menu. The following web page will be shown. PPTP/L2TP Link Enable PPTP - Click this radio button to enable a PPTP client to establish a tunnel to a DSL m[...]

Vigor2110 Series User’s Guide 108 PPP Client Mode - Click Enable to activate this mode for WAN2. SIM PIN code - Type PIN code of the SIM card that will be used to access Internet. Modem Initial String - Such value is used to initialize USB modem. Please use the default value. If you have any question, please contact to your ISP. APN Name - APN(Ac[...]

Vigor2110 Series User’s Guide 109 Fixed IP Address - Type a fixed IP address. WAN IP Network Settings Obtain an IP address automatically – Click this button to obtain the IP address automatically. Specify an IP address – Click this radio button to specify some data. IP Address – Type the IP address. Subnet Mask – Type the subnet mask. 4 4[...]

Vigor2110 Series User’s Guide 110 W W h h a a t t i i s s R R o o u u t t i i n n g g I I n n f f o o r r m m a a t t i i o o n n P P r r o o t t o o c c o o l l ( ( R R I I P P ) ) V igor router will exchange routing informati on with neighboring routers using the RIP to accomplish IP routing. This allows users to cha nge the information of the [...]

Vigor2110 Series User’s Guide 111 4 4 . . 2 2 . . 2 2 G G e e n n e e r r a a l l S S e e t t u u p p This page provides you the general settings for LAN. Click LAN to open the LAN settings page and choose General Setup . 1st IP Addr ess T ype in private IP address for connecting to a local private network (Default: 192.168.1.1). 1st Subnet Mask [...]

Vigor2110 Series User’s Guide 112 S tart IP Address: Enter a value of the IP address pool for the DHCP server to start with when issuing IP addresses. If the 2nd IP address of your router is 220.135.240.1, the starti ng IP address must be 220.135.240.2 or greater , but smaller than 220.135.240.254. IP Pool Counts: Enter the number of IP addresses[...]

Vigor2110 Series User’s Guide 113 If you want to use another DHCP server in the network other than the V igor Router ’ s, you can let Relay Agent help you to redirect the DHCP request to the specified location. Enable Server - Let the router assign IP address to every host in the LAN. Disable Server – Let you manually assign IP address to eve[...]

Vigor2110 Series User’s Guide 114 There are two common scenarios of LAN setti ngs that stated in Chapter 4. For the configuration examples, please refer to that chap ter to get more information for your necessity. 4 4 . . 2 2 . . 3 3 S S t t a a t t i i c c R R o o u u t t e e Go to LAN to open setting page and choose Static Route . Index The num[...]

Vigor2110 Series User’s Guide 115 1. Go to LAN page and click General Setup , select 1st Subnet as the RIP Protocol Control. Then click the OK button. Note: There are two reasons that we have to appl y RIP Protocol Control on 1st Subnet. The f irst is that the LAN inte rface can exchange RI P packets with the neighboring routers via the 1st subne[...]

Vigor2110 Series User’s Guide 116 3. Return to St a t i c R o u t e Setup page. Click on another Index Number to add another static route as show below , which regulates a ll packets destined to 21 1.100.88.0 will be forwarded to 192.168.1.3. 4. Go to Diagnostics and choose Routing T able to verify current routing table.[...]

Vigor2110 Series User’s Guide 117 4 4 . . 2 2 . . 4 4 V V L L A A N N Virtual LAN function provides you a very convenient way to manage hosts by g rouping them based on the physical port. You can also mana ge the in/out rate of each port. Go to LAN page and select VLAN . The following page will appear. Click Enable to invoke VL AN function. To ad[...]

Vigor2110 Series User’s Guide 118 4 4 . . 2 2 . . 5 5 B B i i n n d d I I P P t t o o M M A A C C This function is used to bind the IP and MAC address in LAN to have a strengthening co ntrol in network. When this function is enabled, all the assigned IP and MAC address binding together cannot be changed. If you modified the binding IP or MAC addr[...]

Vigor2110 Series User’s Guide 119 Add It allows you to add the one you choose from the ARP table or the IP/MAC address typed in Add and Edit to the table of IP Bind List . Edit It allows you to edit and modify the selected IP address and MAC address that you create before. Delete You can remove any item listed in IP Bind List . Simply click and s[...]

Vigor2110 Series User’s Guide 120 forward all access request with public IP address fro m external users to the mapping private IP address/port of the server. The port redirection can only apply to incoming traffic. To use this function, please go to NAT page and choose Port Redirection web page. The Port Redirection Table provides 20 port-m appi[...]

Vigor2110 Series User’s Guide 121 Enable Check this box to enable su ch port redirection setting. Mode Two options (Single and Range) are provided here for you to cho ose. To set a range for the specific service, select Range . In Range mode, if the public port (start port and end port) and the starting IP of private IP had been entered, the syst[...]

Vigor2110 Series User’s Guide 122 4 4 . . 3 3 . . 2 2 D D M M Z Z H H o o s s t t As mentioned above, Port Redirection can redirect incoming TCP/UDP or othe r traffic on particular ports to the specific private IP address/port of host in the LAN. However, other IP protocols, for example Protocols 50 (ESP) and 51 (A H), do not travel on a fixed po[...]

Vigor2110 Series User’s Guide 123 The security properties of NA T are somewhat bypassed if you set up DMZ host. W e suggest you to add additional filter rules or a secondary firewall. Click DMZ Host to open the following page: If you previously have set up WAN Alias for PPPoE or Static or Dynamic IP mode , you will find them in Aux. WAN IP for yo[...]

Vigor2110 Series User’s Guide 124 Choose PC Click this button and then a window will automatically pop up, as depicted below. The window consists of a list of private IP addresses of all hosts in your LAN network. Select one private IP address in the list to be the DMZ host. When you have selected one private IP from the above dialog, the IP addr[...]

Vigor2110 Series User’s Guide 125 Comment Specify the name for the defined network service. Local IP Address Display the private IP address of the local host offering the service. Status Display the state for the corresponding entry. X or V is to represent the Inactive or Active state. To add or edit port settings, click one index number on the p[...]

Vigor2110 Series User’s Guide 126 While the broadband users demand more bandwidth f or multimedia, interactive applications, or distance learning, security has been always the most concerned. The firewall of the Vigor router helps to protect your local network against attack from unauthorized outsiders. It also restricts users in the local networ[...]

Vigor2110 Series User’s Guide 127 S S t t a a t t e e f f u u l l P P a a c c k k e e t t I I n n s s p p e e c c t t i i o o n n ( ( S S P P I I ) ) Stateful inspection is a firewall architecture that works at the network layer. Unlike legacy static packet filtering, which examines a packet based on the information in its header, stateful inspec[...]

Vigor2110 Series User’s Guide 128 4 4 . . 4 4 . . 2 2 G G e e n n e e r r a a l l S S e e t t u u p p General Setup allows you to adjust setti ngs of IP Filter and common options. Here you can enable or disable the Call Filter or Data Filter . Under some circumstance, your filter set can be linked to work in a serial manner. So here you assign th[...]

Vigor2110 Series User’s Guide 129 Such page allows you to choose filtering prof iles including QoS, Load-Balance policy, WCF, APP Enforcement, URL Content Filter for data transmission via Vigor router. Filter Select Pass or Block for the packets that do not match with the filter rules. Sessions Control The number typed here is the total sessions [...]

Vigor2110 Series User’s Guide 130 APP Enforcement Select an APP Enfor cement profile for global IM/P2P application blocking. If there is no profile for you to s elect, please choose [Create New] from the drop down list in this page to create a new profile. All the hosts in LAN must follow the standard configured in the APP Enforcement profile sel[...]

Vigor2110 Series User’s Guide 131 please open Syslog. From Codepage Information of Setup dialog, you will see the recommended codepage listed on the dialog box. Window size – It determines the size of TCP protocol (0~65535). T he more the value is, the better the performance will be. However , if the network is not s table, small value will be [...]

Vigor2110 Series User’s Guide 132 4 4 . . 4 4 . . 3 3 F F i i l l t t e e r r S S e e t t u u p p Click Firewall and click Filter Setup to open the setup page. To edit or add a filter, click on the set numbe r to edit the individual set. The following page will be shown. Each filter set contains up to 7 rules. Click on the rule num ber button to [...]

Vigor2110 Series User’s Guide 133 To edit Filter Rule , click the Filter Rule index button to enter the Filter Rule setup page. Check to enable the Filter Rule Check this box to enable the filter rule. Comments Enter filter set comments/description. Maximum length is 14- character long. Index(1-15) Set PCs on LAN to work at certain time interval [...]

Vigor2110 Series User’s Guide 134 To set the IP address manually, please choose Any Address/Single Address/ Range Address/Subnet Address as the Address Type and type them in this dialog. In addition, if you want to use the IP range from defined groups or objects, please choose Group and Objects as the Address Type. From the IP Group drop down lis[...]

Vigor2110 Series User’s Guide 135 Protocol - Specify the protocol(s) which this filter rule will apply to. Source/Destination Port – (=) – when the first and last value are the same, it indicates one port; when the first and last values are different, it indicates a range for the port and available for this service type. (!=) – when the fir[...]

Vigor2110 Series User’s Guide 136 MAC Bind IP When the IP Object Profile (with specif ied MAC Address and IP address for Address T y pe) is selected for Source IP /Destination IP setting, the system will process the packet according to the following rules: z If the MAC address of the packet meets the specified MAC address listed in IP Object Prof[...]

Vigor2110 Series User’s Guide 137 for W eb Content Filter by checking the Log box. It will be sent to Syslog server . Please refer to section Syslog/Mail Alert for more detailed information. SysLog For troubleshooting needs you can specify the filter log and/or CSM log here. Check the corresponding box to enable the log function. Then, the filter[...]

Vigor2110 Series User’s Guide 138 will be. However , if the network is not s table, small value will be proper . Session timeout –Setting timeout for sessions can make the best utilization of network resources. However , Queue timeout is configured for TCP protoc ol only ; session timeout is configured for the data flow which matched with the f[...]

Vigor2110 Series User’s Guide 139 E E x x a a m m p p l l e e As stated before, all the traffic will be separate d and arbitrated using on of two IP filters: call filter or data filter. You may preset 12 call filters and data filters in Filter Setup and even link them in a serial manner. Each filter set is co mposed by 7 filter rules, which can b[...]

Vigor2110 Series User’s Guide 140 4 4 . . 4 4 . . 4 4 D D o o S S D D e e f f e e n n s s e e As a sub-functionality of IP Filter/Firewall, th ere are 15 types of detect/ defense function in the DoS Defense setup. The DoS Defense functionality is disabled for default. Click Firewall and click DoS Defense to open the setup page. Enable Dos Defense[...]

Vigor2110 Series User’s Guide 141 Threshold of ICMP packets fro m Internet has exceeded the defined value, the router will discard the ICMP echo requests coming from the Internet. The default setting for threshold and timeout are 50 packets per second and 10 seconds, respectively. Enable PortScan detection Port Scan attacks the Vigor router by se[...]

Vigor2110 Series User’s Guide 142 Block Ping of Death Check the box to activate the Block Ping of Death function. This attack involves the perpetrator sending overlapping packets to the target hosts so that those target hosts will hang once they re-construct the packets. The Vigor routers will block any packets realizing this attacking activity. [...]

Vigor2110 Series User’s Guide 143 4 4 . . 5 5 O O b b j j e e c c t t s s S S e e t t t t i i n n g g s s For IPs in a range and service ports in a limited range usually will be applied in configuri ng router’s settings, therefore we can define them with objects and bind them with groups for using conveniently. Later, we can select that object/[...]

Vigor2110 Series User’s Guide 144 Name Type a name for this profile. Maximum 15 characters are allowed. Interface Choose a proper interface. For example, the Direction setting in Edit Filter Rule will ask you specify IP or IP range for WAN or LAN or any IP address. If you choose LAN as the Interface here, and choose LAN as the direction setting i[...]

Vigor2110 Series User’s Guide 145 Subnet Mask Type the subnet mask if the Subnet Address type is selected. Invert Selection If it is checked, all the IP addresses except the ones listed above will be applied la ter while it is chosen. Below is an example of IP objects settings. 4 4 . . 5 5 . . 2 2 I I P P G G r r o o u u p p This page allows you [...]

Vigor2110 Series User’s Guide 146 Name Type a name for this profile. Maximum 15 characters are allowed. Interface Choose WAN, LAN or Any to display all the available IP objects with the specified interface. Available IP Objects All the available IP objects with the specified interface chosen above will be shown in this box. Selected IP Objects Cl[...]

Vigor2110 Series User’s Guide 147 4 4 . . 5 5 . . 3 3 S S e e r r v v i i c c e e T T y y p p e e O O b b j j e e c c t t You can set up to 96 sets of Service Type Objects with different conditions. Set to Factory Default Clear all profiles. Click the number under Index co lumn for settings in detail. Name Type a name for this profile. Protocol S[...]

Vigor2110 Series User’s Guide 148 filter rule will filter out any port number. (=) – when the first and last value are the same, it indicates one port; when the first and last values are different, it indicates a range for the port and available for this profile. (!=) – when the first and last value are the same, it indicates all the ports ex[...]

Vigor2110 Series User’s Guide 149 Click the number under Index co lumn for settings in detail. Name Type a name for this profile. Available Service Type Objects All the available service objects that you have added on Objects Setting>>Service Type Object will be shown in this box. Selected Service Type Objects Click >> button to add t[...]

Vigor2110 Series User’s Guide 150 Set to Factory Default Clear all profiles. Click the number under Index column for setting in detail. Name Type a name for this profile, e.g., game. Contents Type the content for such profile. For example, type gambling as Contents. When you browse th e webp age, the page with gambling information will be watched[...]

Vigor2110 Series User’s Guide 151 Set to Factory Default Clear all profiles. Click the number under Index column for setting in detail. Name Type a name for this group. Available Keyword Objects You can gather keyword objects from Keyword Object page within one keyword group. All the available Keyword objects that you have created will be shown i[...]

Vigor2110 Series User’s Guide 152 Click the number under Profile column for configuration in details. Profile Name Type a name for this profile. Type a name for such profile and check all the ite ms of file extension that will be processed in the router. Finally, click OK to save this profile.[...]

Vigor2110 Series User’s Guide 153 4 4 . . 6 6 C C S S M M P P r r o o f f i i l l e e C C o o n n t t e e n n t t S S e e c c u u r r i i t t y y M M a a n n a a g g e e m m e e n n t t ( ( C C S S M M ) ) CSM is an abbreviation of Content Security Management which is used to control IM/P2P usage, filter the web content and URL conten t to reach [...]

Vigor2110 Series User’s Guide 154 Vigor router will then decide whether to allow access to this site according to the categories you have selected. Please note that this action will not introduce any delay in your Web surfing because each of multiple load balanced datab ase servers can handle millions of requests for categorization. Note: The pri[...]

Vigor2110 Series User’s Guide 155 Below shows the items which are categorized under P2P . Profile Name Type a name for the CSM profile. Select All Click it to choose all of the items in this page. Clear All Uncheck all the selected boxes. The profiles configured here can be applied in the Firewall>>General Setup and Firewall>>Filter S[...]

Vigor2110 Series User’s Guide 156 4 4 . . 6 6 . . 2 2 U U R R L L C C o o n n t t e e n n t t F F i i l l t t e e r r P P r r o o f f i i l l e e To provide an appropriate cyberspace to users, Vigor router equips with URL Content Filter not only to limit illegal traffic from/to the ina ppropriate web sites but also prohibit other web feature wher[...]

Vigor2110 Series User’s Guide 157 Profile Name Type a name for the CSM profile. Priority It determines the action that this router will apply. Both: Pass – The router will let all the packages that match with the conditions specified in URL Access Control and Web Feature below passing through. When you choose this setting, both configuration se[...]

Vigor2110 Series User’s Guide 158 Log None – There is no log file will be recorded for this profile. Pass – Only the log about Pass w ill be recorded in Syslog. Block – Only the log about Block will be recorded in Syslog. All – All the actions (Pass and Block) will be recorded in Syslog. URL Access Control Enable URL Access Control - Chec[...]

Vigor2110 Series User’s Guide 159 Web Feature Enable Restrict Web Feature - Check this box to make the keyword being blocked or passed. Action - This setting is available only when Either: URL Access Control First or Either: Web Feature Firs is selected. Pass allows accessing into the corresponding webpage with the keywords listed on the box belo[...]

Vigor2110 Series User’s Guide 160 4 4 . . 6 6 . . 3 3 W W e e b b C C o o n n t t e e n n t t F F i i l l t t e e r r P P r r o o f f i i l l e e There are three ways to activate WCF on vigor router, using Service Activation Wizard , by means of CSM>>Web Content Filter Profile or via System Maintenance>>Activation . Service Activation[...]

Vigor2110 Series User’s Guide 161 whether it is categorized to access into the test server selected. Find more Click it to open http://myvigor.draytek.com for searching another qualified and suitable server. Test a site to verify whether it is categorized Click this link to do the verification. Set to Factory Default Click this link to retrieve t[...]

Vigor2110 Series User’s Guide 162 Profile Name Type a name for such profile. Log None – There is no log file will be recorded for this profile. Pass – Only the log about Pass w ill be recorded in Syslog. Block – Only the log about Block will be recorded in Syslog. All – All the actions (Pass and Block) will be recorded in Syslog. White/Bl[...]

Vigor2110 Series User’s Guide 163 Action Pass - allow accessing into the corr esponding webpage with the categories listed on the box below. Block - restrict accessing into the corresponding webpage with the categories listed on the box below. If the web pages do not match with the specified feature set here, it will be processed with reverse act[...]

Vigor2110 Series User’s Guide 164 To activate the function of limit session, simply click Enable and set the default session limit. Enable Click this button to activate the function of limit session. Disable Click this button to close the function of limit session. Default Max Sessions Defines the default session number used for each computer in [...]

Vigor2110 Series User’s Guide 165 Edit Allows you to edit the settings for the selected limitation. Delete Remove the selected settings existing on the limitation list. Administration Message Type the words which will be displayed when reaches the maximum number of Internet sessions permitted. Index (1-15) in Schedule Setup You can type in four s[...]

Vigor2110 Series User’s Guide 166 Default RX limit Define the default speed of the downstream for each computer in LAN. Allow auto adjustment to make the best utilization of available bandwidth. Router will detect if there is enough bandwidth remained for using according to the bandwidth limit set by the user. If yes, the router will adjust the a[...]

Vigor2110 Series User’s Guide 167 z Classification: Identify ing low-latency or cr ucial applications and marking them for high-priority service level enforcement throughout the network. z Scheduling: Based on classification of service level to assign packets to queues and associated service types The basic QoS implementation in Vigor routers is [...]

Vigor2110 Series User’s Guide 168 This page displays the QoS settings result of the WAN interface. Click the Setup link to access into next page for the general setup of W AN interface. As to class rule, simply click the Edit link to access into next for configuration. You can configure general setup for the WAN interface, edit the Class Rule, an[...]

Vigor2110 Series User’s Guide 169 Enable the QoS Control The factory default for this setting is checked. Please also define which traffic the QoS Control settings will apply to. IN- apply to incoming traffic only. OUT- apply to outgoing traffic only. BOTH- apply to both incoming and outgoing traffic. Check this box and click OK , then click Setu[...]

Vigor2110 Series User’s Guide 170 application. Note: The rate of outbound/inbound m ust be sma ller than the real bandwidth to ensure correct calculation of QoS. It is suggested to set the bandwidth value for inbound /outbound as 80% - 85% of physical network speed provided by ISP to m aximize the QoS performance. E E d d i i t t t t h h e e C C [...]

Vigor2110 Series User’s Guide 171 For adding a new rule, click Add to open the following page. ACT Check this box to invoke these settings. Local Address Click the Edit button to set the local IP address (on LAN) for the rule. Remote Address Click the Edit button to set the remote IP address (on LAN/WAN) for the rule. Edit It allows you to edit s[...]

Vigor2110 Series User’s Guide 172 E E d d i i t t t t h h e e S S e e r r v v i i c c e e T T y y p p e e f f o o r r C C l l a a s s s s R R u u l l e e To add a new service type, edit or delete an existed service type, please click the Edit link under Service Type field. After you click the Edit link, you will see the following page.[...]

Vigor2110 Series User’s Guide 173 For adding a new service type, click Add to open the following pag e. Service Name Type in a new service for your request. Service Type Choose the type (TCP, UDP or TCP/UDP) for the new service. Port Configuration Click Single or Range as the Type . If you select Range, you have to type in the starting port numbe[...]

Vigor2110 Series User’s Guide 174 Click Bandwidth Management>>APP QoS to open the following page. Enable Click Enable to activate APP QoS function. Click Disable to deactivate APP QoS function. Use Default Setting The packets will be transmitted with the default settings. That is, VoIP packets will be the first to be sent out and P2P packet[...]

Vigor2110 Series User’s Guide 175 4 4 . . 8 8 A A p p p p l l i i c c a a t t i i o o n n s s Below shows the menu items for Applications. 4 4 . . 8 8 . . 1 1 D D y y n n a a m m i i c c D D N N S S The ISP often provides you with a dynamic IP address when you c onnect to the Internet via your ISP. It means that the public IP address assigned to [...]

Vigor2110 Series User’s Guide 176 Index Click the number below Index to access into the setting page of DDNS setup to set account(s). Domain Name Display the domain name that you set on the setting page of DDNS setup. Active Display if this account is active or inactive. View Log Display DDNS log status. Force Update Force the router updates its [...]

Vigor2110 Series User’s Guide 177 Delete a Dynamic DNS Account In the DDNS setup menu, click the Index number you want to delete and then push Clear All button to delete the account. 4 4 . . 8 8 . . 2 2 S S c c h h e e d d u u l l e e The Vigor router has a built-in real time clock which can update itself manually or automatically by means of Net[...]

Vigor2110 Series User’s Guide 178 Enable Schedule Setup Check to enable the schedule. Start Date (yyyy-mm-dd) Specify the starting date of the schedule. Start Time (hh:mm) Specify the starting time of the schedule. Duration Time (hh:mm) Specify the duration (or period) for the schedule. Action Specify which action Call Schedule should apply durin[...]

Vigor2110 Series User’s Guide 179 1. Make sure the PPPoE connection and T ime Setup is working properly . 2. Configure the PPPoE always on from 9:00 to 18:00 f or whole week. 3. Configure the For ce Down from 18:00 to next day 9:00 for whole week. 4. Assign these two profiles to the PPPoE Internet access profile. Now , the PPPoE Internet connecti[...]

Vigor2110 Series User’s Guide 180 4 4 . . 8 8 . . 4 4 U U P P n n P P The UPnP (Universal Plug and Play) protocol is supported to bring to network connected devices the ease of installation and configurati on which is already available for directly connected PC peripherals with the existing Windows 'Plug and Play' system. For NAT router[...]

Vigor2110 Series User’s Guide 181 The reminder as regards concern about Firewall and UPnP Can't work with Firewall Software Enabling firewall applications on your P C may cause the UPnP function not working properly. This is because these applicati ons will block the accessing ability of some network ports. Security Considerations Activating[...]

Vigor2110 Series User’s Guide 182 4 4 . . 8 8 . . 5 5 I I G G M M P P IGMP is the abbreviation of Internet Group Management Protocol . It is a communication protocol which is mainly used for managing the membership of Internet Protocol m ulticast groups. Enable IGMP Proxy Check this box to enable this function. The application of multicast will b[...]

Vigor2110 Series User’s Guide 183 4 4 . . 8 8 . . 6 6 W W a a k k e e o o n n L L A A N N A PC client on LAN can be woken up by the router it connects. When a user wants to wake up a specified PC through the router, he/she must type correct MAC address of the specified PC on this web page of Wake on LAN of this router. In addition, such PC must h[...]

Vigor2110 Series User’s Guide 184 4 4 . . 9 9 V V P P N N a a n n d d R R e e m m o o t t e e A A c c c c e e s s s s A Virtual Private Network (VPN) is the extension of a private network that encompasses links across shared or public networks like the Intern et. In short, by VPN technolog y, you can send data between two computers across a share[...]

Vigor2110 Series User’s Guide 185 Dial-In PPP Authentication PAP Only Select this option to force the router to authenticate dial-in users with the PAP protocol. PAP or CHAP Selecting this option means the router will attempt to authenticate dial-in users with th e CHAP protocol first. If the dial-in user does not support this protocol, it will f[...]

Vigor2110 Series User’s Guide 186 There are two encapsulation methods used in IPSec, Transport and Tunnel . The Transport mode will add the AH/ESP payload and use original IP header to encapsulate the data payload only. It can just apply to local packet, e.g., L2TP over IPSec. The Tunnel mode will not only add the AH/ESP payload but also use a ne[...]

Vigor2110 Series User’s Guide 187 4 4 . . 9 9 . . 4 4 I I P P S S e e c c P P e e e e r r I I d d e e n n t t i i t t y y To use digital certificate for p eer authentication in either LAN-to-LAN connection or Remote User Dial-In connection, here you may edit a table of peer certificate for selectio n. As shown below, the router provides 32 entrie[...]

Vigor2110 Series User’s Guide 188 Profile Name Type the name of the profile. Accept Any Peer ID Click to accept any peer regardless of its identity. Accept Subject Alternative Name Click to check one specific field of digital signature to accept the peer with matching value. The field can be IP Address, Domain, or E-mail Address . The box under t[...]

Vigor2110 Series User’s Guide 189 Set to Factory Default Click to clear all indexes. Index Click the number below Index to access into the setting page of Remote Dial-in User. User Display the username for the specific dial-in user of the LAN-to-LAN profile. The symbol ??? represents that the profile is empty. Status Display the access state of t[...]

Vigor2110 Series User’s Guide 190 User account and Authentication Enable this account - Check the box to enable this function. Idle Timeout- If the dial-in user is idle over the limitation of the timer, the router will drop this connection. By default, the Idle Timeout is set to 300 seconds. Allowed Dial-In Type PPTP - Allow the remote dial-in us[...]

Vigor2110 Series User’s Guide 191 security methods in the general settings . Netbios Naming Packet z Pass – Click it to have an inquiry for data transmission between the hosts located on both sides of VPN Tunnel while connecting. z Block – When there is conflict occurred between the hosts on both sides of VPN Tunnel in connecting, such functi[...]

Vigor2110 Series User’s Guide 192 4 4 . . 9 9 . . 6 6 L L A A N N t t o o L L A A N N Here you can manage LAN-to-LAN connections by maintaining a table of connection profiles. You may set parameters including specified c onnection direction (dial-in or dial-out), connection peer ID, connection type (VPN c onnection - including P PTP, IPSec Tunnel[...]

Vigor2110 Series User’s Guide 193 Profile Name Specify a name for the profile of the LAN-to-LAN connection. Enable this profile Check here to activate this profile. VPN Dial-Out Through Use the drop down menu to choose a proper WAN interface for this profile. This setting is useful for dial-out only. WAN1 First - While connecting, the router will[...]

Vigor2110 Series User’s Guide 194 both sides of VPN Tunnel in connecting, such function can block data transmission of Netbios Naming Packet inside the tunnel. Multicast via VPN Some programs might send multicast packets via VPN connection. Pass – Click this button to let multicast packets pass through the router. Block – This is default sett[...]

Vigor2110 Series User’s Guide 195 Nice to Have: Apply the IPSec policy first, if it is applicable during negotiation. Otherwise, the dial-out VPN connection becomes one pure L2TP connection. Must: Specify the IPSec policy to be definitely applied on the L2TP connection. User Name This field is applicable when you select, PPTP or L2TP with or with[...]

Vigor2110 Series User’s Guide 196 IKE phase 1 mode - Select from Main mode and Aggressive mode. The ultimate outcome is to exchange security proposals to create a protected secure channel. Main mode is more secure than Aggressive mode since more exchanges are done in a secure channel to set up the IPSec session. However, the Aggressive mode is fa[...]

Vigor2110 Series User’s Guide 197 Allowed Dial-In Type Determine the dial-in connection with different types. PPTP - Allow the remote dial-in user to make a PPTP VPN connection through the Internet. You should set the U ser Name and Password of remote dial-in user below. IPSec Tunnel- Allow the remote dial-in user to trigger an IPSec VPN connecti[...]

Vigor2110 Series User’s Guide 198 above will apply the authentication methods and security methods in the general settings. User Name This field is applicable when you select PPTP or L2TP with or without IPSec policy above. Password This field is applicable when you select PPTP or L2TP with or without IPSec policy above. VJ Compression VJ Compres[...]

Vigor2110 Series User’s Guide 199 Network Mask configuration. You can modify the settings if required. More Add a static route to direct all traffic destined to more Remote Network IP Addresses/ Remote Network Mask through the VPN connection. This is usually used when you find there are several subnets behind the remote VPN router. RIP Direction [...]

Vigor2110 Series User’s Guide 200 4 4 . . 1 1 0 0 C C e e r r t t i i f f i i c c a a t t e e M M a a n n a a g g e e m m e e n n t t A digital certificate works as an electronic ID, which is issued by a certification authority (CA). It contains information such as your name , a serial number, expiration dates etc., and the digital signature of t[...]

Vigor2110 Series User’s Guide 201 Type in all the information that the window requests. Then click Generate again. Import Click this button to import a saved file as the certification information. Refresh Click this button to refresh the information listed below. View Click this button to view the detailed settings for certificate request. After [...]

Vigor2110 Series User’s Guide 202 4 4 . . 1 1 0 0 . . 2 2 T T r r u u s s t t e e d d C C A A C C e e r r t t i i f f i i c c a a t t e e Trusted CA certificate lists three sets of trusted CA certificate. To import a pre-saved trusted CA certificate, please click IMPORT to open the following window. Use Browse… to find out the saved text file. [...]

Vigor2110 Series User’s Guide 203 4 4 . . 1 1 0 0 . . 3 3 C C e e r r t t i i f f i i c c a a t t e e B B a a c c k k u u p p Local certificate and Trusted CA certificate for this router can be saved within one file. Please click Backup on the following screen to save them. If you want to set encryption password for these certificates, please typ[...]

Vigor2110 Series User’s Guide 204 z Calling via SIP Servers First, the Vigor V models of yours will have to register to a SIP Registrar by sending registration messages to validate. Then, bo th parties’ SIP proxies will forward the sequence of messages to caller to establish the session . If you both register to the same SIP Registrar, then it [...]

Vigor2110 Series User’s Guide 205 4 4 . . 1 1 1 1 . . 1 1 D D i i a a l l P P l l a a n n This page allows you to set phone book and digit map for the VoIP function. Click the Phone Book and Digit Map links on the page to access into next pages for dialplan settings. P P h h o o n n e e B B o o o o k k In this section, you can set your VoIP conta[...]

Vigor2110 Series User’s Guide 206 Click any index number to display the dial plan setup page. Enable Click this to enable this entry. Phone Number The speed-dial number of this index. This can be any number you choose, using digits 0- 9 and * . Display Name The Caller-ID that you want to be displayed on your friend’s screen. This let your frien[...]

Vigor2110 Series User’s Guide 207 D D i i g g i i t t M M a a p p For the convenience of user, this page allows users to edit prefix number for the SIP account with adding number, stripping number or replacing number. It is used to help user having a quick and easy way to dial out through VoIP interface. Enable Check this box to invoke this setti[...]

Vigor2110 Series User’s Guide 208 OP Number The front number you type here is the first part of the account number that you want to execute special function (according to the chosen mode) by using the prefix number. Min Len Set the minimal length of the dial number for appl ying the prefix number settings. Take the above picture (Prefix Table Set[...]

Vigor2110 Series User’s Guide 209 Click any index number to display the dial plan setup page. Enable Click this to enable this entry. Call Direction Determine the direction for the phone call, IN – incoming call, OUT-outgoing call, IN & OUT – both incoming and outgoing calls. Barring Type Determine the type of the VoIP phone call, URI/URL[...]

Vigor2110 Series User’s Guide 210 For Block Unknown Domain – this function can block incomi ng calls (through Phone port) from unrecognized domain that is not specified in SIP accounts. Such control also can be done based on preconfigured schedules. For Block IP Address – this function can block incoming calls (through Phone port) com ing fro[...]

Vigor2110 Series User’s Guide 211 R R e e g g i i o o n n a a l l This page allows you to process incoming or out going phone calls by regional. Default values (common used in most areas) will be shown on this web page. You can change the number based on the region that the router is placed. Last Call Return [Miss] Sometimes, people might miss so[...]

Vigor2110 Series User’s Guide 212 (ID) not displayed on the display panel of remote end. Hide caller ID [Deact] Dial the number typed in this field to release this function. Call Waiting [Act] Dial the number typed in this field to make all the incoming calls waiting for your answer. Call Waiting [Deact] Dial the number typed in this field to rel[...]

Vigor2110 Series User’s Guide 213 4 4 . . 1 1 1 1 . . 2 2 S S I I P P A A c c c c o o u u n n t t s s In this section, you set up your own SIP setti ngs. When you apply for an account, your SIP service provider will give you an Account Name or user name, SIP Registrar, Proxy, and Domain name . (The last three might be the same in some case). Then[...]

Vigor2110 Series User’s Guide 214 Click the index number to configure an SIP account. Profile Name Assign a name for this profile for identifying. You can type similar name with the domain. For example, if the domain name is draytel.org , then you m ight set draytel-1 in this field. Register via If you want to make VoIP call without register pers[...]

Vigor2110 Series User’s Guide 215 Account Number/Name Enter your account name of SIP Address, e.g. every text before @. Authentication ID Check the box to invoke this function and enter the name or number used for SIP Authorization with SIP Registrar. If this setting value is the same as Account Name, it is not necessary for you to check the box [...]

Vigor2110 Series User’s Guide 216 Single Codec – If the box is checked, only the selected Codec will be applied. Packet Size The amount of data contained in a single packet. The default value is 20 ms, which means the data packet will contain 20 ms voice information. Voice Active Detector This function can detect if the voice on both sides is a[...]

Vigor2110 Series User’s Guide 217 4 4 . . 1 1 1 1 . . 3 3 P P h h o o n n e e S S e e t t t t i i n n g g s s This page allows user to set phone settings fo r Phone 1 and Phone 2 respectively. However, it changes slightly according to different model you have. Phone List Port – Phone1 and Phone2 allow you to set general settings for PSTN phones[...]

Vigor2110 Series User’s Guide 218 D D e e t t a a i i l l e e d d S S e e t t t t i i n n g g s s f f o o r r P P h h o o n n e e P P o o r r t t Click the number link for Phone port, you can access into t he following page for configuring Phone settings. Hotline Check the box to enable it. Type in the SIP URL in the field for dialing automatical[...]

Vigor2110 Series User’s Guide 219 T.38 Fax Function Check the box to enable T.38 FAX Relay function Error Correction Mode – Choose the mode for error correction. Call Forwarding There are four options for you to choose. Disable is to close call forwarding function. Always means all the incoming calls will be forwarded into SIP URL without any r[...]

Vigor2110 Series User’s Guide 220 page. Use the drop down list to choose one of the profile names for the accounts as the default one for this phone setting. Play dial tone only when account registered - Check this box to invoke the function. In addition, you can press the Advanced button to configure tone settings, volume gain, MISC and DTMF mod[...]

Vigor2110 Series User’s Guide 221 Also, you can specify each field for your necessity. It is recommended for you to use the default settings for VoIP communication. Volume Gain Mic Gain (1-10)/Speaker Gain (1-10) - Adjust the volume of microphone and speaker by entering number from 1- 10. The larger of the number, the louder the volume is. MISC D[...]

Vigor2110 Series User’s Guide 222 DTMF tone and transfer it into SIP form. Then it will be sent to the remote end with SIP message. Payload Type (rfc2833) - Choose a number from 96 to 127, the default value was 101. This setting is available for the OutBand (RFC2833) mode.[...]

Vigor2110 Series User’s Guide 223 4 4 . . 1 1 1 1 . . 4 4 S S t t a a t t u u s s From this page, you can find codec, connection and ot her important call status for each port. Refresh Seconds Specify the interval of refresh time to obtain the latest VoIP calling information. The information will update immediately when the Refresh button is clic[...]

Vigor2110 Series User’s Guide 224 connection session. Rx Pkts Total number of received voice packets during this connection session. Rx Losts Total number of lost packets during this connection session. Rx Jitter The jitter of received voice packets. In Calls Accumulation for the times of in call. Out Calls Accumulation for the times of out call.[...]

Vigor2110 Series User’s Guide 225 M M u u l l t t i i p p l l e e S S S S I I D D s s Vigor router supports four SSID settings for wireless connections. Each SSID can be defined with different name and download/upload rate for selecting by stations connected to the route r wirelessly. S S e e c c u u r r i i t t y y O O v v e e r r v v i i e e w [...]

Vigor2110 Series User’s Guide 226 may set up a wireless LAN for visitors only so they can connect to Internet without hassle of the confidential information leakage. For a more flexible deployment, you may add filters of MAC addresses to isolate users’ access from wired LAN. Manage Wireless Stations - Station List will display all the station i[...]

Vigor2110 Series User’s Guide 227 4 4 . . 1 1 2 2 . . 2 2 G G e e n n e e r r a a l l S S e e t t u u p p By clicking the General Settings , a new web page will appear so that you could configure the SSID and the wireless channel. Please refer to the following figure for more information. Enable Wireless LAN Check the box to enable wireless funct[...]

Vigor2110 Series User’s Guide 228 Index(1-15) Set the wireless LAN to work at certain time interval only. You may choose up to 4 schedules out of the 15 schedules pre-defined in Applications >> Schedule setup. The default setting of this filed is blank and the function will always work. Hide SSID Check it to prevent from wireless sniffing a[...]

Vigor2110 Series User’s Guide 229 preamble with 56 bit sync filed instead of long pream ble with 128 bit sync field. However, some original 11b wireless network devices only support long preamble. Check it to use Long Preamble if needed to communicate with this kind of devices. Packet-OVERDRIVE This feature can enhance the performance in data tra[...]

Vigor2110 Series User’s Guide 230 4 4 . . 1 1 2 2 . . 3 3 S S e e c c u u r r i i t t y y This page allows you to set security with diffe rent modes for SSID 1, 2, 3 and 4 respectively. After configuring the correct settings, please click OK to save and invoke it. By clicking the Security Settings , a new web page will appear so that you could co[...]

Vigor2110 Series User’s Guide 231 802.1x authentication. Either 8~63 ASCII characters, such as 012345678(or 64 Hexadecima l digits leading by 0x, such as "0x321253abcde..."). Type - Select from Mixed (WPA+WPA2) or WPA2 only. Pre-Shared Key (PSK) - Either 8~63 ASCII characters, such as 012345678 (or 64 Hexadecimal digits leading b y 0x, [...]

Vigor2110 Series User’s Guide 232 4 4 . . 1 1 2 2 . . 4 4 A A c c c c e e s s s s C C o o n n t t r r o o l l In the Access Control , the router may restrict wireless access to cert ain wireless clients only by locking their MAC address into a black or wh ite list. The user may block wireless clients by inserting their MAC addresses into a black [...]

Vigor2110 Series User’s Guide 233 OK Click it to save the access control list. Clear All Clean all entries in the MAC address list. 4 4 . . 1 1 2 2 . . 5 5 W W P P S S WPS (Wi-Fi Protected Setup) provides easy procedure to m ake network connection between wireless station and wireless access point (vigor router) with the encryption of WPA and WPA[...]

Vigor2110 Series User’s Guide 234 z If you want to use PIN code, you have to know the PIN code specified in wireless client. Then provide the PIN code of the wireless clie nt you wish to connect to the vigor router. For WPS is supported in WPA-PSK or WPA2-PSK mode, if you do not choose such mode in Wireless LAN>>Security , you will see the [...]

Vigor2110 Series User’s Guide 235 only. Authentication Mode Display current authentication mode of the router. Only WPA2/PSK and WPA/PSK support WPS. Configure via Push Button Click Start PBC to invoke Push-Button style WPS setup procedure. The router will wait for WPS requests from wireless clients about two minutes. The WPS LED on the router wi[...]

Vigor2110 Series User’s Guide 236 The application for the WDS-Repeater mode is depicted as below: The major difference between these two modes is that: while in Repeater mode, the packets received from one peer AP can be repeated to another peer AP through WDS links. Yet in Bridge mode, packets received from a WDS link will only be for warded to [...]

Vigor2110 Series User’s Guide 237 Mode Choose the mode for WDS setting. Disable mode will not invoke any WDS setting. Bridge mode is designed to fulfill the first type of application. Repea ter mode is for the second one. Security There are three types for security, Disable , WEP and Pre-shared key . The setting you choose here will make the foll[...]

Vigor2110 Series User’s Guide 238 leading by “0x”. Bridge If you choose Bridge as the connecting mode, please type in the peer MAC address in these fields. Four peer MAC addresses are allowed to be entered in this pa ge at one time. Yet please disable the unused link to get better perform ance. If you want to invoke the peer MAC address, reme[...]

Vigor2110 Series User’s Guide 239 based on the station capability. Aggregation MSDU Aggregation MSDU can combine frames with different sizes. It is used for improving MAC layer’s performance for some brand’s clients. The default setting is Enable. 4 4 . . 1 1 2 2 . . 8 8 W W M M M M C C o o n n f f i i g g u u r r a a t t i i o o n n WMM is a[...]

Vigor2110 Series User’s Guide 240 CWMin or equals to CWMin value. Both values will influence the time delay for WMM accessing categories. The difference between AC_VI and AC_VO categories must be smaller; however, the difference between AC_BE and AC_BK categories must be greater. Txop It means transmission opportunity. For WMM categories of AC_VI[...]

Vigor2110 Series User’s Guide 241 4 4 . . 1 1 2 2 . . 9 9 A A P P D D i i s s c c o o v v e e r r y y Vigor router can scan all regulatory channels and find working APs in the neighborhood. Based on the scanning result, users will know which channel is clean for usage. Also, it can be used to facilitate finding an AP for a WDS li nk. Notice that [...]

Vigor2110 Series User’s Guide 242 4 4 . . 1 1 2 2 . . 1 1 0 0 S S t t a a t t i i o o n n L L i i s s t t Station List provides the knowledge of connecting wire less clients now along with its status code. There is a code summary belo w for explanation. For convenient Access C ontrol , you can select a WLAN station and click Add to Access Control[...]

Vigor2110 Series User’s Guide 243 4 4 . . 1 1 3 3 U U S S B B A A p p p p l l i i c c a a t t i i o o n n USB diskette can be regarded as a server. By way of Vigor router, clients on LAN can access, write and read data stored in USB diskette. After setting the configuration in USB Application , you can type the IP address of the Vigor router and [...]

Vigor2110 Series User’s Guide 244 Default Charset is for English based file name. For Simplified Chinese file/directory names, please choose GB2312; for Traditional Chinese file/directory names, choose BIG5. Samba Service Settings Click Enable to invoke samba service via the router. Later, you can view the files inside the USB storage disk throug[...]

Vigor2110 Series User’s Guide 245 Click any index number to access into configuration page. FTP /Samba User Enable – Click this button to activate this profile (account) for FTP service or Samba User service. Later, the user can use the username specified in this page to login into FTP server. Disable – Click this button to disable such profi[...]

Vigor2110 Series User’s Guide 246 Access Rule It determines the authority for such profile. Any user, who uses such profile for accessing in to USB disk, must follow the rule specified here. File – Check the items (Read, Write and Delete) for such profile. Directory –Check the items (List, Create and Re move) for such profile. Before you clic[...]

Vigor2110 Series User’s Guide 247 4 4 . . 1 1 3 3 . . 3 3 F F i i l l e e E E x x p p l l o o r r e e r r To review the content of USB diskette via USB port of the router, please open USB Application Explorer to browse the files. Refresh Click this icon to refresh files list. Back Click this icon to return to the upper directory. Create Click thi[...]

Vigor2110 Series User’s Guide 248 4 4 . . 1 1 3 3 . . 4 4 D D i i s s k k S S t t a a t t u u s s This page is to monitor the status for th e FTP users who accessing into FTP server (USB disk) via the Vigor router. Connection Status If there is no USB disk connected to Vigor router, “ No Disk Connected ” will be shown here. Once the USB disk [...]

Vigor2110 Series User’s Guide 249 4 4 . . 1 1 4 4 S S y y s s t t e e m m M M a a i i n n t t e e n n a a n n c c e e For the system setup, there are several items that you have to know the way of configuration: Status, Administrator Password, Configuration Backup, Syslog, Time setup, Reboot System, Firmware Upgrade. Below shows the menu items fo[...]

Vigor2110 Series User’s Guide 250 DNS Display the assigned IP address of the primary DNS. WAN------- Link Status Display current connection status. MAC Address Display the MAC address of the WAN Interface. Connection Display the connection type. IP Address Display the IP address of the WAN interface. Default Gateway Display the assigned IP addres[...]

Vigor2110 Series User’s Guide 251 4 4 . . 1 1 4 4 . . 2 2 T T R R - - 0 0 6 6 9 9 This device supports TR-069 standard. It is very convenient for an administrator to m anage a TR-069 device through an Auto Configuration Server, e.g., VigorACS. ACS Server On Choose the interface for the router connecting to ACS server. ACS Server URL/Username/Pass[...]

Vigor2110 Series User’s Guide 252 Server IP – Type the IP address of the STUN server. Server Port – Type the port number of the STUN server. Minimum Keep Alive Period – If STUN is enabled, the CPE must send binding request to the server for the purpose of maintaining the binding in the Gateway. Please type a number as the minimum period. Th[...]

Vigor2110 Series User’s Guide 253 4 4 . . 1 1 4 4 . . 4 4 C C o o n n f f i i g g u u r r a a t t i i o o n n B B a a c c k k u u p p B B a a c c k k u u p p t t h h e e C C o o n n f f i i g g u u r r a a t t i i o o n n Follow the steps below to backup your configuration. 1. Go to System Maintenance >> Configuration Backup . The following[...]

Vigor2110 Series User’s Guide 254 4. Click Save button, the configuration will download a utomatically to your computer as a file named config.cfg . The above example is using W indows platform for demonstrating exam ples. The Mac or Linux platform will appear dif ferent windows, but the backup function is still available. Note: Backup for Certif[...]

Vigor2110 Series User’s Guide 255 4 4 . . 1 1 4 4 . . 5 5 S S y y s s l l o o g g / / M M a a i i l l A A l l e e r r t t SysLog function is provided for users to monitor router. There is no bother to directly get into the Web Configurator of the router or borrow debug equipm ents. SysLog Access Setup Enable - Check Enable to activate function of[...]

Vigor2110 Series User’s Guide 256 User Name Type the user name for authentication. Password Type the password for authentication. Enable E-mail Alert Check the box to send alert m essage to the e-mail box while the router detecting the item(s) you specify here. Click OK to save these settings. For viewing the Syslog, please do the following: 1. J[...]

Vigor2110 Series User’s Guide 257 4 4 . . 1 1 4 4 . . 6 6 T T i i m m e e a a n n d d D D a a t t e e It allows you to specify where the time of the router should be inquired from. Current System Time Click Inquire Time to get the current time. Use Browser Time Select this option to use the browser time from the remote administrator PC host as ro[...]

Vigor2110 Series User’s Guide 258 4 4 . . 1 1 4 4 . . 7 7 M M a a n n a a g g e e m m e e n n t t This page allows you to manage the setti ngs for access control, access list, port setup, and SMP setup. For example, as to management access control, the port number is used to send/receive SIP message for building a session. The default value is 50[...]

Vigor2110 Series User’s Guide 259 private. Manager Host IP Set one host as the manager to execute SNMP function. Please type in IP address to specify certain host. Trap Community Set trap community by typing a proper name . The default setting is public. Notification Host IP Set the IP address of the host that will receive the trap community. Tra[...]

Vigor2110 Series User’s Guide 260 4 4 . . 1 1 4 4 . . 9 9 F F i i r r m m w w a a r r e e U U p p g g r r a a d d e e Before upgrading your router firmware, you need to i nstall the Router Tools. The Firmware Upgrade Utility is included in the tools. The following web page will guide you to upgrade firmware by using an exam ple. Note that this ex[...]

Vigor2110 Series User’s Guide 261 4 4 . . 1 1 4 4 . . 1 1 0 0 A A c c t t i i v v a a t t i i o o n n There are three ways to activate WCF on vigor router, using Service Activation Wizard , by means of CSM>>Web Content Filter Profile or via System Maintenance>>Activation . After you have finished the setting profiles for WCF (refer to[...]

Vigor2110 Series User’s Guide 262 4 4 . . 1 1 5 5 D D i i a a g g n n o o s s t t i i c c s s Diagnostic Tools provide a useful way to view or diagnose the status of your Vigor router. Below shows the menu items for Diagnostics. 4 4 . . 1 1 5 5 . . 1 1 D D i i a a l l - - o o u u t t T T r r i i g g g g e e r r Click Diagnostics and click Dial-ou[...]

Vigor2110 Series User’s Guide 263 4 4 . . 1 1 5 5 . . 2 2 R R o o u u t t i i n n g g T T a a b b l l e e Click Diagnostics and click Routing Table to open t he web page. Refresh Click it to reload the page. 4 4 . . 1 1 5 5 . . 3 3 A A R R P P C C a a c c h h e e T T a a b b l l e e Click Diagnostics and click ARP Cache Table to view the content [...]

Vigor2110 Series User’s Guide 264 4 4 . . 1 1 5 5 . . 4 4 D D H H C C P P T T a a b b l l e e The facility provides information on IP address as signments. This information is helpful in diagnosing network problems, such as IP address conflicts, etc. Click Diagnostics and click DHCP Table to open the web page. Index It displays the connection ite[...]

Vigor2110 Series User’s Guide 265 #Pseudo Port It indicates the temporary port of the router used for NAT. Peer IP:Port It indicates the destination IP address and port of remote host. Interface It displays the representing number for different interface. Refresh Click it to reload the page. 4 4 . . 1 1 5 5 . . 6 6 D D a a t t a a F F l l o o w w[...]

Vigor2110 Series User’s Guide 266 Index Display the number of the data flow. IP Address Display the IP address of the monitored device. TX rate (kbps) Display the transmission speed of the monitored device. RX rate (kbps) Display the receiving speed of the monitored device. Sessions Display the session number that you specified in Limit Session w[...]

Vigor2110 Series User’s Guide 267 4 4 . . 1 1 5 5 . . 7 7 T T r r a a f f f f i i c c G G r r a a p p h h Click Diagnostics and click Traffic Graph to pen the web page. Choose WAN1 Bandwidth, Sessions, daily or weekly for viewi ng different traffic graph. Click Refresh to renew the graph at any time. The horizontal axis represents time. Yet the v[...]

Vigor2110 Series User’s Guide 268 Clear Click this link to remove the result on the window. 4 4 . . 1 1 5 5 . . 9 9 T T r r a a c c e e R R o o u u t t e e Click Diagnostics and click Trace Route to open the web page. This page allows you to trace the routes from router to the host. Simply type the IP address of the host in the box and click Run [...]

Vigor2110 Series User’s Guide 269 4 4 . . 1 1 6 6 S S u u p p p p o o r r t t A A r r e e a a When you click it, you will be guided to visit myvigor.draytek.com and open the corresponding pages directly. Click Support Area>>Application Note , the following web page will be displayed. Click Support Area>>FAQ , the following web page wi[...]

Vigor2110 Series User’s Guide 270 Click Support Area>>Product Registration , the following web page will be displayed.[...]

Vigor2110 Series User’s Guide 271 5 A A p p p p l l i i c c a a t t i i o o n n a a n n d d E E x x a a m m p p l l e e s s 5 5 . . 1 1 C C r r e e a a t t e e a a L L A A N N - - t t o o - - L L A A N N C C o o n n n n e e c c t t i i o o n n B B e e t t w w e e e e n n R R e e m m o o t t e e O O f f f f i i c c e e a a n n d d H H e e a a d d [...]

Vigor2110 Series User’s Guide 272 have known. 3. Go to LAN-to-LAN . Click on one index number to edit a profile. 4. Set Common Settings as shown below. You should enable both of VPN connections because any one of the parties may start the VPN connection. 5. Set Dial-Out Settings as shown below to dial to connect to Router B aggressively with the [...]

Vigor2110 Series User’s Guide 273 If a PPP-based service is selected, you should further specify the remote peer IP Address, Username, Password, PPP Authentication and VJ Compression for this Dial-Out connection. 6. Set Dial-In settings to as shown below to allow Router B dial-in to build VPN connection. If an IPSec-based service i s selected, yo[...]

Vigor2110 Series User’s Guide 274 If a PPP-based service is selected, you should further specify the remote peer IP Address, Username, Password, and VJ Compression for this Dial-In connection. 7. At last, set the remote network IP/subnet in TCP/IP Network Settings so that Router A can direct the packets destined to the remote network to Router B [...]

Vigor2110 Series User’s Guide 275 For using IPSec-based service, such as IPSec or L2TP with IPSec Policy, you have to set general settings in IPSec General Setup , such as the pre-shared key that both parties have known. 3. Go to LAN-to-LAN . Click on one index number to edit a profile. 4. Set Common Settings as shown below. You should enable bot[...]

Vigor2110 Series User’s Guide 276 If a PPP-based service is selected, y ou should further specify the remote peer IP Address, Username, Password, PPP Authentication and VJ Compression for this Dial-Out connection. 6. Set Dial-In settings to as shown below to allow Router A dial-in to build VPN connection. If an IPSec-based service is selected, y [...]

Vigor2110 Series User’s Guide 277 If a PPP-based service is selected, y ou should further specify the remote peer IP Address, Username, Password, and VJ Compression for this Dial-In connection. 7. At last, set the remote network IP/subnet in TCP/IP Network Settings so that Router B can direct the packets destined to the remote network to Router A[...]

Vigor2110 Series User’s Guide 278 5 5 . . 2 2 C C r r e e a a t t e e a a R R e e m m o o t t e e D D i i a a l l - - i i n n U U s s e e r r C C o o n n n n e e c c t t i i o o n n B B e e t t w w e e e e n n t t h h e e T T e e l l e e w w o o r r k k e e r r a a n n d d H H e e a a d d q q u u a a r r t t e e r r The other common case is that [...]

Vigor2110 Series User’s Guide 279 3. Go to Remote Dial-In User . Click on one index number to edit a profile. 4. Set Dial-In settings to as shown below to allow the remote user dial-in to build VPN connection. If an IPSec-based service is sele cted, you may further specify the remote peer IP Address, IKE Authentication Method and I PSec Security [...]

Vigor2110 Series User’s Guide 280 Settings in the remote host: 1. For Win98/ME, you may use "Dial-up Networking" to create the PPTP tunnel to Vigor router. For Win2000/XP, please use "Network and Dial-up connections" or “Smart VPN Client”, complimentary software to help you create PPTP, L2TP, and L2TP over IPSec tunnel. Yo[...]

Vigor2110 Series User’s Guide 281 You may further specify the method you use to get IP, the security method, and authentication method. If the Pre-Shared Key is selected, it should be consistent with the one set in VPN router. If a PPP-based service is selected, you should fu rther specify the remote VPN server IP address, Username, Password, and[...]

Vigor2110 Series User’s Guide 282 4. Click Connect button to build connection. When the connection is successful, you will find a green light on the right down corner. 5 5 . . 3 3 Q Q o o S S S S e e t t t t i i n n g g E E x x a a m m p p l l e e Assume a teleworker someti mes works at hom e and takes care of children. When working time, he woul[...]

Vigor2110 Series User’s Guide 283 2. Click Setup link of W AN. Make sure the QoS Control on the left c orner is checked. And select BOTH in Dir ection . 3. Return to previous page. Enter th e Name of Index Class 1 by clicking Edit link. T y pe the name “ E-m ail ” for Class 1. 4. For this index, the user will set reserved bandwidth (e.g., 25%[...]

Vigor2110 Series User’s Guide 284 5. Return to previous page. Enter th e Name of Index Class 2 by clicking Edit link. In this index, the user will set reserved bandwidth for HTTPS . And click OK . 6. Click Setup link for W AN. 7. Check Enable UDP Band width Control on the bott om to prevent enormous UDP traf fic of V oIP influent other applicatio[...]

Vigor2110 Series User’s Guide 285 Class Name of Index 3. In this index, he will set reserved bandwidth for 1 VPN tunnel. 9. Click Edit to open the following window . Check the ACT box, first. 10. Then click Edit of Local Address to set a worker ’ s subnet address. Click Edit of Remote Address to set headquarter ’ s IP address. Leave other fie[...]

Vigor2110 Series User’s Guide 286 Y ou can just set the settings wrapped inside the red rectangles to fit the request of NA T usage. T o use another DHCP server in the network rather than the built-in one of V igor Router , you have to change the settings as show below .[...]

Vigor2110 Series User’s Guide 287 Y ou can just set the settings wrapped inside the red rectangles to fit the request of NA T usage.[...]

Vigor2110 Series User’s Guide 288 5 5 . . 5 5 C C a a l l l l i i n n g g S S c c e e n n a a r r i i o o f f o o r r V V o o I I P P f f u u n n c c t t i i o o n n 5 5 . . 5 5 . . 1 1 C C a a l l l l i i n n g g v v i i a a S S I I P P S S e e v v e e r r Example 1: Both John and David have SIP Addresses from different servi ce providers. John?[...]

Vigor2110 Series User’s Guide 289 (Use default value) Phone Number for John) Example 2: Both John and David have SIP Addresses from the same servi ce provider. John’s SIP URL: 1234@draytel.org , David ’s SIP URL: 4321@draytel.org Settings for John DialPlan index 1 Phone Number: 1111 Display Name: David SIP URL: 4321@draytel.org SIP Accounts S[...]

Vigor2110 Series User’s Guide 290 5 5 . . 5 5 . . 2 2 P P e e e e r r - - t t o o - - P P e e e e r r C C a a l l l l i i n n g g Example 3: Arnor and Paulin have Vigor routers respectively. The y can call each other without SIP Registrar. First they must have each other’s IP address and assign an Account Name for the port used for calling. Arn[...]

Vigor2110 Series User’s Guide 291 5 5 . . 6 6 U U p p g g r r a a d d e e F F i i r r m m w w a a r r e e f f o o r r Y Y o o u u r r R R o o u u t t e e r r Before upgrading your router firmware, you need to i nstall the Router Tools. The Firmware Upgrade Utility is included in the tools. 1. Go to www.draytek.com . 2. Access into Support >>[...]

Vigor2110 Series User’s Guide 292 6. Follow the onscreen instructions to install the tool. Finally, click Finish to end the installation. 7. From the Start menu, open Programs and choose Router Tools XXX >> Firmware Upgrade Utility . 8. Type in your router IP, usually 192. 168.1.1 . 9. Click the button to the right side of Firmware file typ[...]

Vigor2110 Series User’s Guide 293 5 5 . . 7 7 R R e e q q u u e e s s t t a a c c e e r r t t i i f f i i c c a a t t e e f f r r o o m m a a C C A A s s e e r r v v e e r r o o n n W W i i n n d d o o w w s s C C A A S S e e r r v v e e r r 1. Go to Certificate Management and choose Local Certificate .[...]

Vigor2110 Series User’s Guide 294 2. You can click GENERATE button to start to edit a certificate request. Enter the information in the certificate request. 3. Copy and save the X509 Local Certificate Requet as a text file and save it for later use. 4. Connect to CA server via web browser. Follo w the i nstruction to submit the request. Below we [...]

Vigor2110 Series User’s Guide 295 Select Advanced request . Select Submit a certificate request a base64 encoded PKCS #10 file or a renewal request using a base64 encoded PKCS #7 file Import the X509 Local Certificate Requet text file. Select Router (Offline request) or IPSec (Offline request) below. Then you have done the request and the ser ver[...]

Vigor2110 Series User’s Guide 296 you will find the below window showin g “------BEGINE CERTIFICATE------.....” 6. You may review the detail informati on of the certificate by clicking View button.[...]

Vigor2110 Series User’s Guide 297 5 5 . . 8 8 R R e e q q u u e e s s t t a a C C A A C C e e r r t t i i f f i i c c a a t t e e a a n n d d S S e e t t a a s s T T r r u u s s t t e e d d o o n n W W i i n n d d o o w w s s C C A A S S e e r r v v e e r r 1. Use web browser connecting to the CA server that you would like to retrieve its CA cert[...]

Vigor2110 Series User’s Guide 298 2. In Choose file to download , click CA Certificate Current and Base 64 encoded, and Download CA certificate to save the .cer. file. 3. Back to Vigor router, go to Trusted CA Certificate . Click IMPORT button and browse the file to import the certificate (.cer file) in to Vigor router. When finished, click refre[...]

Vigor2110 Series User’s Guide 299 5 5 . . 9 9 C C r r e e a a t t i i n n g g a a n n A A c c c c o o u u n n t t f f o o r r M M y y V V i i g g o o r r The website of MyVigor (a server located on http://myvigor.draytek.com ) provides several useful services (such as Anti-Spam, Web Content Filter, Anti-Intrusion, and etc.) to filtering the web p[...]

Vigor2110 Series User’s Guide 300 3. Click the link of Create an account now . 4. Check to confirm that you accept the Agreement and click Accept . 5. Type your personal information in this page and then click Continue . 6. Choose proper selection for your computer and click Continue .[...]

Vigor2110 Series User’s Guide 301 7. Now you have created an account successfully. Click START. 8. Check to see the confirmation email with the title of New Account Confirmation Letter from myvigor.draytek.com . 9. Click the Activate my Account link to enable the account that you created. The following screen will be shown to verify the re gister[...]

Vigor2110 Series User’s Guide 302 10. When you see the following page, please type in the account and password (that y ou just created) in the fields of UserName and Password . 11. Now, click Login . Your account has been activated. You can access into MyVigor server to activate the service (e.g., WCF) that you want. 5 5 . . 9 9 . . 2 2 C C r r e[...]

Vigor2110 Series User’s Guide 303 2. Check to confirm that you accept the Agreement and click Accept . 3. Type your personal information in this page and then click Continue . 4. Choose proper selection for your computer and click Continue .[...]

Vigor2110 Series User’s Guide 304 5. Now you have created an account successfully. Click START. 6. Check to see the confirmation email with the title of New Account Confirmation Letter from myvigor.draytek.com . 7. Click the Activate my Account link to enable the account that you created. The following screen will be shown to verify the re gister[...]

Vigor2110 Series User’s Guide 305 8. When you see the following page, please type in the account and password (that you just created) in the fields of UserName and Password . Then type the code in the box of Auth Code according to the value displayed on the right side of it. Now, click Login . Your account has been activated. You can access into [...]

Vigor2110 Series User’s Guide 306 5 5 . . 1 1 0 0 H H o o w w c c a a n n I I g g e e t t t t h h e e f f i i l l e e s s f f r r o o m m U U S S B B s s t t o o r r a a g g e e d d e e v v i i c c e e c c o o n n n n e e c c t t i i n n g g t t o o V V i i g g o o r r r r o o u u t t e e r r ? ? Files on USB storage device can be renamed, upload[...]

Vigor2110 Series User’s Guide 307 3. Make sure the FTP service is running properly. Please open a browser and type ftp://192.168.1.1 . Use the account " user1 " to login. 4. When the following screen appears, it means the FTP service is running properly. 5. Return to USB Application >> USB Disk Status . The information for FTP ser[...]

Vigor2110 Series User’s Guide 308 6. Now, users in LAN of Vigor2110 can access into the USB storage device by typing ftp://192.168.1.1 on any browser . They can add or remove files / directories, depending on the Access Rule for FTP account settings in USB Application >>USB User Management.[...]

Vigor2110 Series User’s Guide 309 T T r r o o u u b b l l e e S S h h o o o o t t i i n n g g This section will guide you to solve abnormal s ituations if you cannot access into the Internet after installing the router and finishing the we b configuration. Please follow sections below to check your basic installation status stage by stage. z Chec[...]

Vigor2110 Series User’s Guide 310 6 6 . . 2 2 C C h h e e c c k k i i n n g g I I f f t t h h e e N N e e t t w w o o r r k k C C o o n n n n e e c c t t i i o o n n S S e e t t t t i i n n g g s s o o n n Y Y o o u u r r C C o o m m p p u u t t e e r r I I s s O O K K o o r r N N o o t t Sometimes the link failure occurs due to the wrong network[...]

Vigor2110 Series User’s Guide 311 4. Select Obtain an IP address automatically and Obtain DNS server address automatically . F F o o r r M M a a c c O O S S 1. Double click on the current used Mac OS on the desktop. 2. Open the Application folder and get into Network . 3. On the Network screen, select Using DHCP from the drop down list of Configu[...]

Vigor2110 Series User’s Guide 312 6 6 . . 3 3 P P i i n n g g i i n n g g t t h h e e R R o o u u t t e e r r f f r r o o m m Y Y o o u u r r C C o o m m p p u u t t e e r r The default gateway IP address of the router is 192.168.1.1. For some reason, you might need to use “ping” command to check the link status of the router. The most import[...]

Vigor2110 Series User’s Guide 313 6 6 . . 4 4 C C h h e e c c k k i i n n g g I I f f t t h h e e I I S S P P S S e e t t t t i i n n g g s s a a r r e e O O K K o o r r N N o o t t Click Internet Access group and then check whether the ISP settings are set correctly. F F o o r r P P P P P P o o E E U U s s e e r r s s 1. Check if the Enable opti[...]

Vigor2110 Series User’s Guide 314 F F o o r r S S t t a a t t i i c c U U s s e e r r s s 1. Check if the Enable option for Broadband Access is selected. 2. Check if WAN IP Network Settings is set appropriately. 3. Check if IP Address, Subnet Mask and Gateway are set correctly (must identify with the values from your ISP) if you choose Specify an[...]

Vigor2110 Series User’s Guide 315 F F o o r r P P P P T T P P U U s s e e r r s s 1. Check if the Enable option for PPTP Link is selected. 2. Check if PPTP Server, Username, and Password are set correctly (must identify with the values from your ISP). 3. Check if WAN IP Network Settings are set properly. If you select Specify an IP address , you [...]

Vigor2110 Series User’s Guide 316 T T r r a a n n s s m m i i s s s s i i o o n n R R a a t t e e i i s s n n o o t t f f a a s s t t e e n n o o u u g g h h Please connect your Notebook with 3G USB Modem to test the connection speed to verify if the problem is caused by Vigor2110. In addition, please refer to the manual of 3G USB Modem for LED S[...]

Vigor2110 Series User’s Guide 317 You can type in four sets of time schedul e for performing auto-reboot. After clicking OK , the router will reboot at the specified time. H H a a r r d d w w a a r r e e R R e e s s e e t t While the router is running (ACT LED blinking), press the Factory Reset button and hold for more than 5 seconds. When you se[...]