Electrolux 5995421640 manual

599542 1640 Dishwasher Use & Care Guide Use & Care Guide Use & Care Guide Use & Care Guide Use & Care Guide Ice Maker[...]

2 Finding Information PLEASE READ AND SA VE THIS GUIDE Thank you for choosing Electrolux , the new premium brand in home appliances. This Use & Care Guide is part of our commitment to customer satisfaction and product quality throughout the service life of your new ice maker . We view your purchase as the beginning of a relationship. T o ensure[...]

3 Finding Information NO NO NO NO NO TE TE TE TE TE Registering your product with Electrolux enhances our ability to serve you. Y ou can register online (at the Internet address below) or by dropping your Product Registration Card in the mail. Complete and mail the Product Registration Card as soon as possible to validate the registration date. PRO[...]

4 TABLE OF CONTENTS Finding Information ........................................... 2 Please Read And Save Thi s Guide ................... 2 Make A Record For Quick Reference ................ 2 Warranty Registration Card ............................... 3 Questions? ........................................................ 3 T able Of Contents ......[...]

5 Safety IMPORT ANT SAFETY INSTRUCTIONS Safety Precautions Do not attempt to install or operate your unit until you have read the safety precautions in this manual. Safety items throughout this manual are labeled with a Danger , W arning or Caution based on the risk type. Definitions ! This is the safety alert symbol. It is used to alert you to pot[...]

6 Safety General Precautions ! D D D D D ANGER ANGER ANGER ANGER ANGER RISK OF CHILD ENTRAPMENT . Before you throw away your old appliance, take off the doors and leave shelves in place so that children may not easily climb inside. ! WARNING WARNING WARNING WARNING WARNING • Never attempt to repair or perform maintenance on the unit until the ele[...]

7 Inst allation INST ALLA TION DIMENSIONS 14 - 15/16” (37.9) 24” (61) 21 - 3/4” (55.2) 34 - 1/8” (86.7) FULL RETRACT HEIGHT W A TER VA LV E W A TER OUTLET W A TER DRAIN 5” (12.7) Figure 1[...]

8 ! CA CA CA CA CA UTION UTION UTION UTION UTION PLEASE READ all instructions completely before attempting to install or operate the unit. All ice makers require a connection to the water supply and improper hook-up can result in substantial property damage! All water and drain connections MUST BE made by a licensed/qualified plumbing contractor . [...]

9 1 Make certain the unit is not plugged into an electrical outlet. 2 Carefully push the power cord grommet through the hole in the back panel. See Figure 2 . 3 Remove 12 screws and back panel. 4 Check that the clamps and hose connections are tight at the following areas illustrated in Figure 3 : • Discharge tube (A) • Drain tube (B) • V ent [...]

10 Drain Pump Connection CONNECTING A DRAIN PUMP If a gravity drain connection is not available, and you have not purchased the E15IM60E with factory installed pump, we strongly recommend the use of the Electrolux EIMP60 drain pump. The Electrolux EIMP60 drain pump is available through your Dealer , or direct from Electrolux with complete installat[...]

11 Site Prep aration PREP ARING THE SITE 1 Position the unit on a flat, level surface, capable of supporting the entire weight of the unit. Remember that the unit will be significantly heavier once it is fully loaded. 2 The surrounding air temperature must be at least 50°F (10°C) but must not exceed 1 10°F (43°C). 3 The unit must not be located[...]

12 Site Prep aration 6 Install and connect the water supply line. See Connecting the W ater Supply for installation requirements. 7 Position the unit to allow free air flow through the front grille (see Figure 6 ). 8 Wipe out inside of unit with a damp cloth. NO NO NO NO NO TE TE TE TE TE The door of the unit may be mounted on either side of the ca[...]

13 W ater Supply Connection CONNECTING THE WA TER SUPPL Y When connecting the water supply , follow these guidelines: • Review the local plumbing codes before you install the unit. • The water pressure should be between 20 and 120 psi. • Make certain a SHUT -OFF V AL VE is installed in the 1/4 inch water supply line. • Connect sufficient tu[...]

14 ! CA CA CA CA CA UTION UTION UTION UTION UTION After completing the installation, turn on the water and recheck water and drain connection for leaks. Apply additional tightening if needed. Do NOT use thread sealing com-pound or tape. W ater Supply Connection 1 Locate the compression fitting and ferrule packed in the unit. Slide the compression f[...]

15 Leveling LEVELING THE UNIT 1 Use a level to check the levelness of the ice maker from front to back and from side to side (see Figure 11 ). 2 If the ice maker is not level, adjust the feet on the corners of the unit as necessary (see Figure 12 ). 3 Check the levelness after each adjustment and repeat the previous steps until the unit is level. I[...]

16 SCREW PLUGS Figure 13 Figure 14 Figure 15 Door Reversal REVERSING THE DOOR (SOME MODELS) All Electrolux units may be left or right hand opening. The door opening is easily reversed by moving the hinge hard-ware to the opposite side (see Figure 13 ). T o reverse the door: 1 Remove top hinge screw pin (7/64" Allen wrench) from cabinet (see Fi[...]

17 Door Reversal 3 Remove top hinge (3 screws), reinstall hinge screw pin, and remount on opposite side BOTTOM (see Figure 17 ). 4 Remove the two door closer inserts from the existing bottom hinge and install as shown on the new bottom hinge (see Figure 18 ). 5 Remove existing bottom hinge (3 screws) and remount on opposite side T OP . Remove hinge[...]

18 Door Adjustment ADJUSTING THE DOOR Y our door is aligned at the factory before shipment. Occasional re-adjustment may be necessary , especially if an overlay panel is installed. The following procedure will correct for up to 1/4" alignment. The door should never be flush with the top of the cabinet. Even when level, the top edge of the door[...]

19 Door Adjustment 4 If door edge opposite the hinges needs to move up, move plate toward outside of door . If door edge needs to move down, move plate toward inside of door (see Figure 23 ). Repeat until top edge of door is parallel with top of cabinet and tighten screws securely . 5 After adjustment is complete, remove the door closers from the b[...]

20 Built-In Inst allation INST ALLING A BUIL T -IN Y our Electrolux product has been designed for either free-standing or built-in installation. When built-in, your ice maker does not require additional air space for top, sides or rear . However , the front grille must NOT be obstructed. ! CA CA CA CA CA UTION UTION UTION UTION UTION Do not install[...]

21 S t art-up INITIAL ST ART -UP Once installation and leveling is complete, the unit is ready for initial start-up and operation. Y our unit is shipped in the OFF position, however , you may turn it ON/ OFF using the cycle selector switch located in the access panel above the grille (see Figure 26 ). 1 Plug the appliance cord into a 1 15V polarize[...]

22 Operation NORMAL OPERA TION The ice maker is designed to make clear ice from most water sources on a consistent basis. W ater is constantly circulated over the evaporator assembly . As the water freezes, gravity causes any sediment to drop into the water trough and not become imbedded in the ice. This gives a clearer ice cube with a low mineral [...]

23 ! WARNING WARNING WARNING WARNING WARNING Disconnect power to the ice maker before making any ice thickness adjustments. Operation ICE DISPENSER OPERA TION & CARE The ice cube thickness control is factory set for best overall performance. The factory setting is designed to maintain an ice bridge of approximately 1/16" to 1/8" under[...]

24 IMPOR IMPOR IMPOR IMPOR IMPOR T T T T T ANT ANT ANT ANT ANT Ice thickness adjustment dial can be rotated 1/4 to 1/2 turn on the number dial. Allow the ice maker to stabilize for 24 hours before making further adjustments. Since ice cubes in any given batch will vary , choose cubes from the sample area for comparison when making adjustments (see [...]

25 Maintenance SPECIAL CONSIDERA TIONS • For best performance, keep the unit out of direct sunlight. • T urn the unit OFF and dispose of any ice cubes if the unit will not be used for 5 days or more. Prop door open to allow for air circulation and prevent mold and mildew . • If the ambient temperature is expected to drop below 45°F (7°C), d[...]

26 Maintenance • DO NOT CLEAN WITH STEEL WOOL P ADS. • DO NOT USE CLEANERS THA T ARE NOT SPECIFICALL Y INTENDED FOR ST AINLESS STEEL (this includes glass, tile and counter cleansers). • If any surface discolors or rusting appears, clean it quickly with Bon-Ami or Barkeepers Friend Cleanser and a non-abrasive cloth. Always clean in the directi[...]

27 Maintenance Condenser Cleaning — Every 3 Months T o maint ain operational ef ficiency , clean the condenser every three months (depending on environmental conditions, more or less frequent cleaning may be necessary). T o remove and replace the grille for access to the condenser fins follow this procedure (see Figure 32 ): 1 Remove the screws a[...]

28 Maintenance Self Cleaning — Every 6 Months T o maint ain operational efficiency , clean the unit every six months (depending on water conditions more or less frequent cleaning may be necessary). If the ice maker requires more frequent cleaning, consult a qualified plumber to test the water quality and recommend appropriate treatment. Ice machi[...]

29 Figure 34 Maintenance 4 Remove the overflow tube by lifting it up while using a slight back and forth motion to loosen it from the drain hole (see Figure 34 ). The water in the reservoir will flow down the drain. 5 Replace the overflow tube after all of the water has drained from the reservoir . 6 Move the cycle selector switch to the CLN positi[...]

30 S torage, V acation and Moving DRAINING FOR NON-USE If the unit is to be stored, moved or not used for extended periods, it will be necessary to drain the system of water . 1 Disconnect power from the unit. 2 Remove ice from the storage bin. 3 Shut off water supply at the main water source. 4 Disconnect the inlet and outlet lines to the water va[...]

31 T roubleshooting BEFORE YOU CALL FOR SERVICE If the unit appears to be malfunctioning, read through Normal Operation first. If the problem persists, check the T roubleshooting Guide . Locate the problem in the guide and refer to the cause and its remedy before calling for service. The problem could be something very simple which can be solved wi[...]

32 T roubleshooting IF SERVICE IS REQUIRED If the need for service arises, contact the dealer from whom the unit was purchased. S tate the Model Number and Serial Number and explain the problem. The Model and Serial Number plate is located inside the unit at the upper right hand corner . If you do not know the name of the selling dealer or local se[...]

33 W arranty Information ICE MA KER WAR RANTY You r i ce make r is pr otect ed by t his w arr an ty WARRANTY PERI OD THROUGH OUR AUTHORIZED SE R V ICERS, WE WI LL: THE CO NS UMER WI LL BE RESP ONSIBL E FOR : FULL ON E -Y EAR WARRANTY One year from original purchase date. Pay all c osts for rep a iri n g or replaci ng any parts of this ap pli anc e [...]