Electrolux Z8800 Series manual

Upright Vacuum Cleaner Owner’s Guide Household Type Z8800 Series IMPORTANT For any advice on your cleaner and to order filters and accessories, please telephone the Electrolux Helpline on 08706 055055 FILTER REPLACEMENT CODE: EF105 and EF106 www.electrolux.co.uk IM P OR T AN T IN F OR M AT I ON 2 — 4 4 5 5 7 10 10 11 11 12 13 13 14 GU A RA N TE[...]

2 IMPORTANT SAFEGUARDS When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER. WARNING To reduce the risk of fire, electric shock, or injury: • Do not use outdoors or on wet surfaces. • Do not leave vacuum cleaner when plugged in. Turn off [...]

3 BEFORE YOU START CHECK THE VOLTAGE Before connecting the cleaner to an electrical supply, ensure that the voltage shown on the rating plate located beneath the cleaner is of the correct voltage for your electricity supply. If it is not, do not use the cleaner but refer back to your dealer. CONNECTING TO YOUR ELECTRICITY SUPPLY Permanently connect[...]

4 SERVICE Should you require service on your Electrolux cleaner, please telephone Electrolux Customer Services on 08706 055055. Before requesting service, please check whether your problem is covered under Service Checklist (see below). New filter pads, brushrolls and drive belts can be obtained from Electrolux Retailers. If difficulty is experienc[...]

5 HOW TO IDENTIFY PARTS OF CLEANER Items in Carton  cleaner body  handle  hose clip  screws (4 in bag)  dusting brush  combination crevice tool & nested wand  turbo nozzle (on some models) 1) Hose 2) Turbo nozzle 3) Filter screen 4) Self cleaning duster (on some models) 5) Duster activation knob 6) Cleaner height setting 7)[...]

6 HOW TO ASSEMBLE cont. Step 3: Move the hose out of the way before the next step (Step 4) as shown. Step 4: Attach the tool caddy by inserting the tab as shown, and rotating it forward. Step 5: Fasten the tool caddy with 2 screws. The left screw will need to be fastened as shown (through the hole in the tool caddy’s hose guide). HOW TO ASSEMBLE [...]

7 HOW TO ASSEMBLE cont. Step 9: Store the dusting brush behind the handle as shown. Step 10: Store the turbo nozzle on the front of the cleaner, above the dust cup, as shown. Push to lock in place. Helpful Hints: Use caution when using this vacuum on area rugs. Do not use the vacuum on or near the fringe of area rugs, as it may damage your rug. HOW[...]

8 HOW TO USE CLEANER cont. Warning: to avoid injury, keep loose clothing, fingers, hair, etc. away from moving brushroll. 4) Set Cleaner Height Setting from High setting for long pile to Low for short pile. Note: If cleaner is hard to push, move selector to next highest setting. Brushroll must reach carpet for best cleaning results. 5) To clean har[...]

9 HOW TO USE ACCESSORIES cont. Warning: To reduce the risk of injury from a falling cleaner, always work with the cleaner below you, pushed against the bottom step. Caution: Do not place the cleaner on the stairs as this may cause carpet damage. HOW TO USE ACCESSORIES cont. 5) Self Cleaning Duster (on some models) - How To Use: The self cleaning du[...]

10 HOW TO USE ACCESSORIES cont. 6) Self Cleaning Duster (on some models) - How To Clean: Secure the duster into the Duster Tube, and rotate the Duster Activation Knob counterclockwise (towards the back of the vacuum) to clean the duster. HOW TO MAINTAIN Important: To avoid unnecessary service calls, check the cyclone, foam & exhaust filters, be[...]

HOW TO MAINTAIN cont. 3) Check the HEPA EF105 Exhaust Filter: Empty the dust cup and do not place it back in the vacuum; lay the vacuum flat on the floor. The HEPA filter is accessed by removing the foam filter & frame, and turning the knob left. Remove the HEPA filter door completely, and brush off or replace the HEPA filter. Place the HEPA fi[...]

HOW TO MAINTAIN cont. How to Clear Blockages in Hose Caution: Make sure On/Off switch is in Off (o) position and power supply cord is unplugged before servicing. 1) Firmly pull the end of the hose from the hose retainer on the back of the vacuum. 2) Check for blockages in the hose and hose retainer. Flexing the hose may help loosen any blockage. If[...]

HOW TO MAINTAIN cont. Caution: Make sure On/Off switch is in Off (o) position and power supply cord is unplugged before replacing belt. Belt pulley can become hot during normal use. To prevent injury, avoid touching the motor shaft when checking the belt. Maintain Brushroll Remove hair and threads from brushroll periodically. For best cleaning bris[...]

Problem Solving CAUTION: Turn off the switch and unplug the electrical cord before servicing. Problem Cause Solution Motor will not start. Power Plug On/Off Switch Thermal Cut Off • Push plug securely into outlet. • Try another outlet. • Check circuit breaker. • Turn on/off switch to |. • Refer to page 2. Motor suddenly stops. Thermal Cut[...]

Problem Cause Solution Motor will not start. Power Plug On/Off Switch Thermal Cut Off • Push plug securely into outlet. • Try another outlet. • Check circuit breaker. • Turn on/off switch to |. • Refer to page 2. Motor suddenly stops. Thermal Cut Off • Refer to page 2. Does not clean carpet or hard floor Dust Cup and Filter(s) Belt Brus[...]

Part No. 79316 (0X/07) Printed in PRC If you experience any problems with your cleaner, don’t struggle taking it back to the shop. Call our dedicated Customer Helpline for help and advice on 08706 055055 Thank you for purchasing an Electrolux cleaner. Don’t Forget to Use Genuine Electrolux Belts and Filters Caution: Damages caused by the use of[...]