Enterasys Networks XSR-3020 manual

X-Pedition ™ Security Router XSR-3020 Getting Started Guide V ersion 3.0 P/N 9033866-06 8.5x11-inch cover with bleed on 4 sides[...]

[...]

i Notice Enterasys Networks  reserv es  the  right  to  make  changes  in  s pecifications  and  other  information  contained  in  this  document  and  its  web  site  without  prior  no tice.  The  reader  should  in  all  cases  consult  Enterasys Networks [...]

ii Regulatory Compliance Information Federal Communications Commiss ion (FCC) Notice The  XSR  complies  with  Title  47,  Par t  15,  Class  A  of  FCC  rule s.  Operation  is  subject  to  the  following  tw o  conditions: •T h i s  device  may  no t  cause  harmful  [...]

iii Industry Canada Notices This  digital  apparatus  does  not  exceed  the  class  A  limits  for  radio  noise  emissions  from  di gital  apparatus  set  out  in  the  Radio  Interfer ence  Regulations  of  the  Canadian  Department  of  Communications. Le ?[...]

iv Product Safety This  product  complies  with  the  following:  UL  60950,  CSA  C22.2  No.  60950,  73/23/EEC,  EN  60950,  EN  60825,  IEC  60950. Use  the  XSR  with  the  Advanced  Pow e r  Soluti ons  (APS61ES ‐ 30)  power  supply  included  with  [...]

v ѻ ѻ ક䇈ᯢк䰘ӊ Supplement to Product Instructions ᳝↦᳝ᆇ⠽䋼៪ܗ㋴ (Hazardous Substance) 䚼ӊৡ⿄ (Parts) 䪙 3E ∲ +J 䬝 &G ݁Ӌ䫀 &U   ໮⒈㘨㣃 3%% ໮⒈Ѡ㣃䝮 3%'( 䞥ሲ䚼ӊ (Metal Parts) hƻ ƻ h ƻ ƻ ⬉䏃῵ഫ ( Circuit M[...]

vi VCCI Notice This  is  a  class  A  product  based  on  the  standard  of  the  V oluntary  Control  Council  for  Interference  by  Information  Te c h n o l o g y  Equipment  (VCCI)  V ‐ 3.  If  this  equipment  is  used  in  a  domestic  environment,[...]

vii Australian T elecom WA R N I N G :  Do  not  install  phone  line  connections  during  an  el ectrical  storm. WA R N I N G :  Do  not  connect  phone  line  until  the  inte rface  has  been  config ured  through  loca l  management.  The  serv ice  provider  [...]

viii Enterasys Networks, Inc. Firmware License Agreement BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT, CAREFULLY READ THIS LICENSE AGREEMENT. This  document  is  an  agreemen t  (“ Agreement” )  betw een  the  end  user  (“Y ou”)  and  Enterasys  Networks,  Inc.,  on  behalf  of  its[...]

ix If  the  Program  is  exported  from  the  United  Stat es  pursuant  to  the  License  Ex ception  TSR  und er  the  U.S.  Export  Administration  Regulations,  in  addition  to  the  restriction  on  transfer  set  forth  in  Sec tion  1  or  [...]

x 11. ASSIGNMENT. You  may  not  assign,  transfer  or  sublicense  this  Agreement  or  any  of  Your  rights  or  obligations  under  this  Agreement,  except  that  You  may  assign  this  Agreem ent  to  any  person  or  entity  which  acquires  s[...]

xi Contents About This Guide Contents of the Guide ..... .................... ................... .................... ................... ................... ... .................... .......... xv Conventions Used in This G uid e ........... ................... .................... ................ ................... ........... .................[...]

xii Configuring the WAN Ports ...... .................... ................... ................... .................... ................. ..... .................. 3-8 PRI Configuration ......... ................... ................ .................... ................... ................... ....... ...................... .. 3-8 BRI Configuration ..[...]

xiii bu ................. ................ ................... ................... ................. ................... ................. ............ ................... 3-36 bU .......... ................... .................... ................ ................... .................... ................ .... ............ ................... 3-36 [...]

xiv[...]

xv About This Guide This guide provides a general overview of th e XSR-3020 hardwar e and softwar e features and describes how to quickl y install and configur e the XSR. Refer to the XSR CLI Reference Guide and XSR User ’ s Guide for information not contained in this document. This guide is w ritten for administrators who want to configure the X[...]

xvi Electrical Hazard : W arns against an action that could result in personal injury or dea th due to an electrical hazard. Riesgo Electric o: Advierte contra una acción que pudiera re sultar en lesión corporal o la muerte debido a un riesgo eléctrico. Elektrisch er Gefahr enhinweis: Installationen sollten nur durch ausgebilde tes und qualifizi[...]

xvii Getting Help For  additional  support  related  to  the  XSR,  contact  Enterasys  Netw orks  using  one  of  the  following  methods: Before  contacting  Ente rasys  Networks  for  technic al  support,  have  the  following  information  ready: •Y o u r  Entera[...]

xviii[...]

XSR Getting Started Guide 1-1 1 Overview This chapter introduces the key features of the XSR-3020 and briefly describes har dware installation. System Description The XSR is a networking device designed for enterp rise r egional offices that provides IP routing over GigabitEthe rnet LAN and T1/E1, S erial (RS 232, X.21, V .35, RS422/530, RS449), Di[...]

System Description 1-2 Overview Figure 1-1 T ypical XSR-3020 T opology Hardware Features The semi-modular XSR, shown in Figure 1-2 , comes equipped with the following featur es: • Standard 1U chassis (1-1 1/16 inches high by 17 in ches wide by 21 inches deep) mountable in a standard 19” rack. • Broadcom 1250 dual-CPU, 64-bit processor (1 700 [...]

System Description XSR Getting Started Guide 1-3 Figure 1-2 XSR-3020 • T wo Network Interface Modu le (NIM ) slots for these optional cards: • 1, 2, or 4 full, fractional and channeli zed T1/E1 W AN NIM with integral CSU/DSU or Primary Rate Interface (PRI) ports (RJ-48C). • 1-port T3/E3 channelized/unchannelized W A N NIM wi th BNC ports. Thi[...]

System Description 1-4 Overview • 14 diagnostic LEDs to displ ay port, and system st atus as well as indicate a Flash upgrade in progr ess. • Five system fans with failur e detection capability and thr ee fans dedicated to power supply cooling. Sof tware Features The XSR provides the following software featur es: Operating System • Multi-thre[...]

System Description XSR Getting Started Guide 1-5 • Simple Network T ime Protocol (SNTP) server •O S f a l l b a c k IP Routing • Static and multipl e routes to the same destination • Redistribution of r outes from RIP , OSPF , BGP , connected, or static into RIP , OSPF , and BGP •R I P - 1 & R I P - 2 •O p e n S h o r t e s t P a t [...]

System Description 1-6 Overview Security • Stateful inspection fi rewall engi ne • F TP , H.323, and RPC (SUN and Microsoft) ALG support • Application commands for F TP , SMTP , & HTTP • Firew all logging and authentication • Firew all interaction with NA T & VPN • Standard and Extended Access Control Lists • Denial of Service[...]

System Description XSR Getting Started Guide 1-7 • Periodic Keep-Alive message s to learn of connection problems • Multi-pr otocol interconnect over Frame Relay - RFC-2427 • RFC-2390 Frame Relay Inverse ARP to discover IP address of r emote peer when used in multi- point mode and responds to incoming Inverse ARP r equests independent of P2P o[...]

System Description 1-8 Overview • Bandwidth optimization (BoD) & Dial on Demand (DoD) • Bandwidth Allocation Protocol (BAP) • Security: P AP/CHAP • Call monitoring • Multilink PPP (MLPPP) • Per call activation for NTT switches • Frame Relay over ISDN Quality of Service (QoS) • T raffic classification using IP Precedence and Diff[...]

System Description XSR Getting Started Guide 1-9 SecurID (third-party plug-in) Certificates (embedded/smart cards) – Micr osoft only •E n c r y p t i o n • Advanced Encryption Standar d (AES), T rip le Data Encryption Standard (3DES), Data Encryption Standard (DES) • 3DES/DES acceleration • Data Integrit y • MD5 & SHA-1 algorithms ?[...]

System Description 1-10 Overview Asynchronous Digit al S ubscriber Line (ADSL) • POTS and ISDN circuit support • A TM Frame UN I (FUNI) data framing format • OAM cells: AIS, RDI, CC, Loopback ove r F4 and F5 flows • Up to 30 A TM Permanent V irtual Cir cuits (PVCs) • A TM U BR traffic class • A TM A daption Layers 0, 5 • PDU encapsula[...]

Installation Overview XSR Getting Started Guide 1-11 • Switched PPP Multilink connections • Backup using ISDN & MLPPP connections • Dialer interface spoofing • Dialer watch Inst allation Overview Installing the XSR consists of performing the fo llowing general steps. For detailed instructions, ref er to Chapters 2 and 3 of this manual. [...]

Installation Overview 1-12 Overview[...]

XSR Getting Started Guide 2-1 2 Hardware Installation Introduction This chapter provides a checklist to verify your shipment, suggestions for the installation si te, and describes how to instal l the following XSR har dware: • NIM cards • Optional - CompactFlas h card (standard with ADSL NIM) • Connecting cables V erifying Y our Shipment Befo[...]

Installing NIM Cards and Rack Mounting 2-2 Hardware Installation • Each XSR AC power supply requires a thr ee-pr onged power receptacle capable of delivering the current and voltage specified in Appendix A . An AC outlet on a separately fused circuit is requir ed for each XSR to provide power r edundancy , and must be located within 182 centimete[...]

Installing NIM Cards and Rack Mounting XSR Getting Started Guide 2-3 4. Remove the NIM slot cover , as shown in Figur e 2-2 , by grasping the handle and pulling it to the side befor e taking it out. Figure 2-2 Removing NIM Slot Cov er 5. Gently attach the NIM car d(s) to the connecto r on the motherboar d and secure with f our screws, as shown in F[...]

Installing NIM Cards and Rack Mounting 2-4 Hardware Installation 7. Attach the rack brackets to the chassi s with the scr ews supplied, as shown in Fi gure 2-4 . Figure 2-4 Fastening Rack Bracket s 8. Mount the bracketed XSR to your rack, as shown in Figur e 2-5 . Figure 2-5 Att aching XSR to Rack NIM 1 NIM 2 1000 GBIC Link TX 10/100/1000 10/100/10[...]

Installing a CompactFlash Memory Card XSR Getting Started Guide 2-5 Inst alling a Comp actFlash Memory Card An optional CompactFlash (CF) memory card provides additional non-volatile storage capabilities in various increments. The CF’s controll er interfaces with a host system allowing data to be written to and read from the CF’s flash memory m[...]

Installing a CompactFlash Memory Card 2-6 Hardware Installation 2. Seat the card in the PCMCIA interface as shown in Fi gure 2-8 . Gently insert the CF into the sl ot, taking care that the CF’s wider gr ooved edge fits into the wider track of the PCMCIA interfa ce. If the car d does not seat easily but stops halfway in to the slot, do not force i[...]

Connecting Cables XSR Getting Started Guide 2-7 Connecting Cables Perform any of the following steps to connect your cabling to optiona l W A N or LAN NIMs, GigabitEthernet ports, and power supply: 1. Connect the serial COM cable pro vided in the packing box to your P C connector , as shown in Figur e 2-9 . Figure 2-9 Connecting Seri al COM (Consol[...]

Connecting Cables 2-8 Hardware Installation Figure 2-1 1 Connecting High Speed Ser ial Connector Figure 2-12 Att aching T3/E3 BNC Connectors NIM 1 NIM 2 SECURITY ROUTERS XSR-3020 NIM 1 NIM 2 S E C U R ITY R O U TE R S XSR-3020 ALARM LOS ENABLE LOF Tx Rx id[...]

Connecting Cables XSR Getting Started Guide 2-9 Figure 2-13 Connecting ADSL Connector A CompactFlash card is provided with the XSR ADSL NIM. It is loaded with the Digital Signal Processing (DSP) firmware ( adsl.fls ) r equired to communicate with your DSLAM. When inserted into the Compa ct Flash slot - upon firs t configu ring an A TM interface - t[...]

Connecting Cables 2-10 Hardware Installation 3. Connect the Ethernet port(s) to your LAN connectors with a cable, as shown in Figure 2-15 . Figure 2-15 Att aching Ethernet Connector 4. Insert the Mini-GBIC module in the GBIC slot then connect the optical cable, as shown in Figure 2- 16 . Figure 2-16 Inserting Mini-GBIC Module 1000 G BIC Link TX 10/[...]

Connecting Cables XSR Getting Started Guide 2-11 5. Attach either the Ethernet or Fi ber E thernet LAN NIM, as shown in Figur e 2-17 and Figure 2- 18 , respectively . Figure 2-17 Att aching Ethernet LAN NIM Connector Figure 2-18 Att aching Ethernet Fiber LAN NIM Connector NIM 1 NIM 2 SECURITY ROUTERS XSR-3020 A C T LIN K N IM - ETH R - 01 NIM 1 NIM[...]

Connecting Cables 2-12 Hardware Installation 6. Attach the power supply cord to the connec tor at the r ear of the XSR, as shown in Figure 2-19 and plug in the country-specific power cor d co nnects to a wall socket. The XSR will power up. Figure 2-19 Connecting Power Supply Cord Y ou are now r eady to configure the softwar e and initialize the XSR[...]

XSR Getting Started Guide 3-1 3 Software Configuration This chapter describes how to init ializ e, quickly set up and verify your configurati on for the XSR. Refer to the XSR CLI Referenc e Guide for a more thor ough explanation of commands and parameter options. The chapter also includes sample co nfiguration scripts, de tailed XSR rebooting chara[...]

Initializing XSR Software 3-2 Software Configuration • ETH 10/100/1000 LEDs turn ON and OFF a fe w times during initialization as the XSR pro ce ed s f rom bo ot rom to po we r u p d ia gn os ti cs to so ft wa re i ma ge , t hen th e y rem ai n ON or OFF depending on the LA N type. • ETHERNET Activity LEDs bl ink when frames pass on the LAN. ?[...]

Opening a COM (Console) Session XSR Getting Started Guide 3-3 first error will be reported, along with a count of the sum of err ors incurred. In the case of a single err or , only the error line will be r eported. Error messages will be logged as well. Because the result of cont inuing to pr ocess a flawed startup-config is not pr edictable, the n[...]

Optional: Configuring Remote Auto In stall 3-4 Software Configuration same node - 10.10.1.2 (configuration of DNS and TF TP servers are not shown here). In short, the DNS server should map IP addresses 133.133.1.2 and 133.133.1.3 to hostnames. On the TF TP server , you should create a startup-config file with names <hostname>-confi g in a dir[...]

Optional: Configuring Remote Auto Install XSR Getting Started Guide 3-5 ****************** REMOTE AUTO INSTA LL TERMINATING***************** + The RAI process is complete and is preoceding to s ystem in itialization where it will process the new startup- config file. Configuring RAI fo r DHCP over LAN The following example configures DHCP server to[...]

Optional: Configuring Remote Auto In stall 3-6 Software Configuration virtual-template 1 pppoe limit per-mac 10 + This is an optional command. pppoe limit max-sessions 32000 + This is an optional command. interface GigabitEthernet1/0/0 no ip address negotiation auto ! interface GigabitEthernet1/0/0.10 encapsulation dot1Q 20 pppoe enable pppoe max-s[...]

Configuring the XSR Name and User Information XSR Getting Started Guide 3-7 + The XSR waits one minute for the PPPoE connection to come up. Phase 4 - ADSL - IP is connected on 0/35, prepare to load startup config + The XSR starts downloading the startup-file. Phase 6 - ATM/ADSL - retrieving file 0000019876543210-confg from tftp server 25 5.255.255.[...]

Configuring the LAN Ports 3-8 Software Configuration XSR(config)#sntp-server enable Remember to save your conf iguration after all edits. Configuring the LAN Port s 1. Enter interface gigabitethernet < 1 | 2 | 3 > to acquir e Interface mode and se lect the first, second or third GigabitEthernet port. 2. Enter ip address <xxx.xxx.xxx.xxx>[...]

Configuring the WAN Ports XSR Getting Started Guide 3-9 The value you set must match the type and format of fered by your service pr ovider and must correlate with the NIM card you ar e configuring: sf or esf for T1 cards , and crc4 or no-crc 4 for E1 cards. 7. Enter linecode < ami | b8zs | hdb3 > to configure the encoding type. Th i s s e tt[...]

Configuring the WAN Ports 3-10 Software Configuration 3. Enter no shutdown to keep the BRI interface enabled. 4. Enter frame-relay lmi-type <ilmi | ansi | q933a | auto | none > to select the Local Management Interface type. 5. Enter interface bri 0:<1 | 2>.<1-30> multi-point to acquire BRI Sub-interface mode and select the BRI por[...]

Configuring the WAN Ports XSR Getting Started Guide 3-11 ADSL Configuration ADSL can be configur ed using three dif ferent ty pes of encapsulatio n: PPPoA, PPPoE, and IPoA. Continue configuration with th e ADSL type of your choice. PPPoE The following commands configure a sample PPPoE topology . The first set configures the LAN interface with dire [...]

Firewall Sample Configuration 3-12 Software Configuration The commands below configur e the A TM interface and sub-interface with a negotiated IP address, CHAP username and pa sswor d, and bans keepalives. XSR(config)#interface ATM 0 XSR(config-if<ATM0/0>)#no shutdown XSR(config-if<ATM0/0.1>)#interface A TM 0.1 XSR(config-if<ATM0/0.1[...]

Firewall Sample Configuration XSR Getting Started Guide 3-13 Figure 3-1 XSR with Firewall T opology In this configuration , the firewall pr ovides protected access from th e private to dmz networks. That is, access is restricted to W eb and mail traffic onl y . The hosts in the private network ar e provided full access to the Internet but access is[...]

Setting Up RIP Routing 3-14 Software Configuration T rial load the completed configuration into the firewall engine, and if successful, load the configuration: XSR(config)#ip firewall load trial XSR(config)#ip firewall load Complete LAN and W AN interface configuration: XSR(config)#interface gigabitetherne t 1 XSR(config-if<G1>)#ip address 22[...]

Configure OSPF Routing XSR Getting Started Guide 3-15 12. Enter network < xxx.xxx.xxx.xxx > (IP address) of the network to be advertised. Repeat the command to configure additional networks. 13. Enter passive-interface type num if you want t o prevent RIP tr ansmissions on the interface. 14. Enter no receive-interface if you want to disable r[...]

Setting Up an SNMP Community String, Traps and V3 Values 3-16 Software Configuration 7. Enter map-class frame-relay < name > to designate this map-class and acquire Map-Class mode. 8. Enter frame-relay cir out < bits > to set the outgoing CIR (the de fault is 56000 bps). Refer to the XSR User ’ s Guide for more deta ils. 9. Enter fram[...]

Configuring Message Logging and Severity Level XSR Getting Started Guide 3-17 Groups of fer users authorization ch oices and read/write privileges. 6. Optional. For SNMPv3, enter snmp-server view < name > { oid-tree | treeEntryName }{ includ ed | excluded } to specify a view . V iews offer use rs selective access to the family tr ee or Object[...]

Connecting Remotely via the Web 3-18 Software Configuration Connecting Remotely via the W eb 1. Enter configure to acquire Configuration mode. 2. Enter ip http server enable to access the XSR over the W eb. 3. Point your terminal’s W eb browser at the XSR’s IP addr ess. Enter http://<XSR IP address> . The initial W eb access wind ow appea[...]

Connecting Remotely via the Web XSR Getting Started Guide 3-19 Click on Pr oduct V ersion to bring up the Pr oduct V ersion window for a hos t of hardwar e, bootrom, and softwar e information as shown in Figure 3-3 . Figure 3-3 Web Produc t V ersion Window Product V ersion Copyright 2004 by Enterasys Networks, Inc. Ha rdw are : Processor boar d ID:[...]

LAN-PPP Services Sample Configuration 3-20 Software Configuration LAN-PPP Services Sample Configuration The sample configuration below , see Figur e 3-4 , creates a PPP , fractional T1 leased line connection from the XSR branch node to the Central Site router and a backup serial dial up link to the Back up Si t e re g i on a l ro u te r . Figure 3-[...]

Frame Relay WAN Link with PPP Backup Sample Configuration XSR Getting Started Guide 3-21 XSR(config-controller<T1-1/0>)#no sh utdown + Enables T1 controller XSR(config)#interface serial 1/0:0 + Configures Serial interface 1, port 1 us ing channel group 0 and acquires Interface mode XSR(config-if<S1/0:0>)#encapsulation ppp + Enables PPP [...]

Frame Relay WAN Link with PPP Backup Sample Configuration 3-22 Software Configuration Configure Users and Passwords XSR(config)#username bob password cl eartext bobspassword + Adds a user and unencrypted password Configure LAN Interface XSR(config)#interface gigabitetherne t 1 + Configures the local LAN port and acquires In terface mode XSR(config-[...]

Frame Relay WAN Link with PPP Backup Sample Configuration XSR Getting Started Guide 3-23 XSR(config-pmap-c<priority-server>)# priority medium 20 6400 + Gives medium priority queue a peak 20% of bandw idth & burst size of 6400 bits per second XSR(config)#policy-map data_policy + Adds a policy map and acquires Policy Map mode XSR(config-pma[...]

Frame Relay WAN Link with PPP Backup Sample Configuration 3-24 Software Configuration Apply QoS XSR(config)#map-class frame-relay CL ASS-FRP + Adds a FR map class and acquires F R Map Class mode XSR(config-map-class<CLASS-FRP>)#fra me-relay cir out 48000 + Sets this map class’ CIR rate at 48000 bits per second XSR(config-map-class<CLASS-[...]

Frame Relay WAN Link with PPP Backup Sample Configuration XSR Getting Started Guide 3-25 XSR(config)#access-list 125 deny ip host 192.168.1.15 any XSR(config)#access-list 125 permit i p 192.162.2.0 0.0.0.255 any XSR(config)#access-list 125 permit i p 192.162.2.0 0.0.0.255 XSR(config)#interface fastethernet 1 XSR(config-if<F1>)#ip access-group[...]

VPN Site-to-Site Sample Configuration 3-26 Software Configuration Configure SNMP The previo usly configured ACL will be applied to all SNMP r equests. Stricter ACLs can be written if tighter security controls ar e required. XSR(config)#snmp-server community to Monitor1 ro 26 + Adds an SNMP community with read-only privileges at tached to ACL 26 XSR[...]

VPN Site-to-Site Sample Configuration XSR Getting Started Guide 3-27 Generate Master Encryption Key If you have not alr eady generated a master encryption key , you must do so now to confi gure the VPN. A master key need only be generated once. Generate the master key: XSR(config)#crypto key master genera te New key is 2173 4521 3764 2ff5 163b 4bdf[...]

VPN Site-to-Site Sample Configuration 3-28 Software Configuration Create a T ransform Set The following tra nsform-set specifies t he sp ecified encryption/data integrity choices, 768-bit Diffie-Hellman, and an SA lifetime expr essed in kilobytes . The SA seconds lifetime value is di sabled. Some commands are abbr eviated. XSR(config)#crypto ipsec [...]

VPN Sample Configuration with Network Extension Mode XSR Getting Started Guide 3-29 XSR(config)#interface vpn 57 multi-p oint XSR(config-int-vpn)#ip address 192.1 68.2.1 255.255.255.0 XSR(config)#router rip XSR(config-router)#network 112.16.10 .0 XSR(config-router)#passive-interface gigabitethernet 2 XSR(config-router)#no receive-interf ace gigabit[...]

VPN Sample Configuration with Network Extension Mode 3-30 Software Configuration Figure 3-6 VPN T opology with NEM, EZ-IPSec and Internet Access If you have not alr eady generated a master encryption key , you must do so now to confi gure the VPN. A master key need only be generated once. Generate the master key . Refer to the following sampl e key[...]

VPN Sample Configuration with Network Extension Mode XSR Getting Started Guide 3-31 Configur e AAA authenti cation by assignin g a virtual subnet t o the DEF AUL T AAA group, associate it with DNS and WINs servers, and add two AAA users with passwords. When a remote XSR tunnels into the local XSR, it will be assigned these DNS, WINS and PP TP value[...]

XSR Rebooting Characteristics 3-32 Software Configuration XSR(config)#access-list 103 permit i p any 10.10.10.0 0.0.0.255 Create crypto map statements for each ACL entry with the mor e protective tunnel mode set by default. Match statements r ender associated ACLs bi-directional: XSR(config)#crypto map test 101 XSR(config)#set transform-set ez-esp [...]

XSR Rebooting Characteristics XSR Getting Started Guide 3-33 CPU: Broadcom BCM1250 Rev 2 VxWorks version: VxWorks5.4.2 Bootrom version: 1.5 Creation date: Aug 26 2003, 10:12:36 Warm Start : from cli Testing Bootrom Integrity << PASSED >> auto-booting... Verifying flash:xsr3000.fls file ... Router S/W size=11989192 sum=0xedd1 compressed_[...]

XSR Rebooting Characteristics 3-34 Software Configuration Power-Up Reboot If you power cycle the XSR by flipping the switc h on the back panel, the XS R will cold r eboot. The startup-config file stor ed in Flash becomes the r unning configuration. Reload Command from the CLI Y ou can reboot the XSR firmwar e by issuing the com mand reload <cold[...]

Bootrom Monitor Mode Commands XSR Getting Started Guide 3-35 • Bootrom is valid. • The software image in Flash is valid. Bootrom Monitor Mode Commands Bootrom monitor mode of fers special user access when the XSR lacks val id softwar e or runs abnormally . Enter the mode by pressing the key combination ( CTRL-C ) during the first five seconds o[...]

Bootrom Monitor Mode Commands 3-36 Software Configuration XSR-3020:bp Enter current password: Enter new password: ****** Re-enter new password: ****** Password has changed. bu This command updates the bootrom from a local file. Y ou are pr ompted to enter data by the following script. When the “ Proceed with erasing Bootrom in flash ...” stat e[...]

Bootrom Monitor Mode Commands XSR Getting Started Guide 3-37 copy This command copies a file using the syntax copy <source name> <destination name> . Y ou can copy files from flash: to cflash: and vice versa. da This command shows system date/time with the sample output below: XSR-3020:da Date: Thursday, 29-MAY-2003. Time: 10:14:07 df T[...]

Bootrom Monitor Mode Commands 3-38 Software Configuration ff This command formats the Flash f ile system. W e recommend that you first save any .dat, .cert, .cfg , and your startup-config files t o cflash: or a PC since any fil es in flash: will be deleted. Y ou are pr ompt ed to enter data by the following script: XSR-3020: ff You will lose all fi[...]

Bootrom Monitor Mode Commands XSR Getting Started Guide 3-39 Local target name (robo1) : Autoboot (yes) : Quick boot (no) : Permanently save the network paramet ers? (y/n) ns This command saves a file over the network using a remote IP addr ess/file path. remove This command removes a file using the syntax remove <sour ce name> <destinatio[...]

Bootrom Monitor Mode Commands 3-40 Software Configuration BadVAddr=08112233 PP - Crashed Task Stack (sp=85febb90 ): 0x85feb790 ffffffff 00000000 00 000008 ffffffff 0x85feb7a0 00000000 00000001 00 000000 00000001 0x85feb7b0 00000000 8214ab00 00 00000a 82142ee0 0x85feb7c0 ffffffff 85feb7c0 ff ffffff bf3285a4 0x85feb7d0 00000000 00000002 ff ffffff 85f[...]

Bootrom Monitor Mode Commands XSR Getting Started Guide 3-41 Local target name : XSR1 Autoboot : enabled Quick boot : no Current GigabitEthernet 0 MAC addres s is: 00:01:f4:2b:3e:1b Current GigabitEthernet 1 MAC addres s is: 00:01:f4:2b:3e:1c Current GigabitEthernet 1 MAC addres s is: 00:01:f4:2b:3e:1d sv This command shows the bootr om version wit[...]

Bootrom Monitor Mode Commands 3-42 Software Configuration[...]

A-1 A Specifications System S pecifications This appendix details XSR data about har dware functionality including : • Process or , system memory , chassis, powe r supply , interfaces • Required cabling, optional Comp actFlash and other accessories • Pinout assignments for W AN and LAN interfaces •L E D b e h a v i o r Refer to tables throu[...]

Cable, CompactFlash and Accessory Specifications A-2 Cable, Comp actFlash and Accessory Specifications Refer to the following table for s pecifications of cables, CompactFlash and accessories for the XSR. This equipment can all be obtained separately fr om Enterasys Networks or thr ough any computer supply retailer . Power Consum ption T ypical val[...]

Cable, CompactFlash and Accessory Specifications XSR Getting Started Guide A-3 2-port sy nch/asynch card 4-port sy nch/asynch card 68-pin, male SCSI III NIM-SER-02 NIM-SER-04 Serial NIM cards 6’ DB-15, X.21 DTE, twisted-pair cab le NIM-X21-CAB-04 Serial link to high speed serial line: 2 or 4 port 6’ DB-25, EIA -232/530 DTE twisted -pair cable N[...]

Cable, CompactFlash and Accessory Specifications A-4 COM (Console) Po rt The XSR comes equipped with a COM serial port useful for initial configuration and management. Using a serial ( null modem) cable, you can attach the router ’s DB-9 COM port to a data terminal port and directly configur e the XSR over th e asynchro nous connection. Then, ope[...]

Cable, CompactFlash and Accessory Specifications XSR Getting Started Guide A-5 GigabitEtherne t Port s The XSR comes equipped with three GigabitEthernet (LAN) ports that support full-duplex 10, 100, or 1000 Mbps transmission. The ports conform to IEEE 802.3 standar d s with 8-pin modular RJ-45 connectors. Because these ports ha ve internal MDI cr o[...]

Cable, CompactFlash and Accessory Specifications A-6 Copper/Fiber-optic Ethernet NIMs The single-port Copper or Fiber - optic Ethernet NIMs, shown in Figure A-3 and Figure A-4 , provide interfaces for half and full-d uplex 10/10 0Base-T or fiber-optic 100Base-F transmission over LAN or W AN networks, respectively . The Co pp er Ethernet NIM incorpo[...]

Cable, CompactFlash and Accessory Specifications XSR Getting Started Guide A-7 2/4-Port Serial NIM Card Port The High Speed Serial NIM car d, as shown in Figure A-6 , provides a W AN interface supporting a serial link to four differ ent types of DTEs: DB-15, 25 , 37, and V . 35. This interface supports dual and quad traffic up to 8 Mbps. Figure A-6[...]

Cable, CompactFlash and Accessory Specifications A-8 Figure A-8 E IA-232/5 30 DTE Pin Assignments 17 18 19 3 RxD2 + RxD 2 1 2 3 11 5 10 4 7 6 8 12 13 15 16 9 14 6 22 3 16 2 14 4 19 5 13 15 12 17 9 7 20 23 1 DSR0+ DS R0 - RxD0 + RxD 0- TxD 0 + TxD0- RTS 0 + RT S0- CTS 0 + CT S0- TxC 0 + TxC0- RxC0 + RxC 0- Si gnal GND Shield GND Si gnal GND DTR 0 + [...]

Cable, CompactFlash and Accessory Specifications XSR Getting Started Guide A-9 Figure A-9 EIA-449 DTE Pin Assignment s 17 18 19 27 21 1 2 3 11 5 10 4 7 6 8 12 13 15 16 9 14 11 29 6 24 4 22 7 25 9 27 5 23 8 26 37 12 30 1 ON0+ ON0- RD0+ RD 0 - SD0+ SD 0 - RS0+ RS 0 - CS0+ CS 0 - ST0+ ST0 - RT0+ RT0 - SG0 Shie ld GND RC0 TR0+ TR 0 - 35 36 37 45 39 44 [...]

Cable, CompactFlash and Accessory Specifications A-10 Figure A-10 Combined V .35/EI A-232/530 DTE Pin Assignment s 1 2 3 11 5 10 4 7 6 8 12 13 15 16 9 14 3 16 2 14 4 19 5 13 15 12 17 9 7 20 23 1 RxD3+ RxD3- TxD3+ TxD3- RTS3+ RTS3- CTS3+ CTS3- TxC3+ TxC3- RxC3+ RxC3- Signal GND Signal GND DTR3+ DTR3- J1 J2 6 22 DSR3+ DSR3- 35 37 45 39 44 38 49 40 50[...]

Cable, CompactFlash and Accessory Specifications XSR Getting Started Guide A-11 Figure A-1 1 V .35 DTE Pin Assignment s 17 19 27 21 1 3 11 5 10 4 15 6 16 12 13 9 14 E R T P S C D Y AA V X B H A DSR 0 RD0+ RD 0 - SD0+ SD 0 - RTS 0 CTS 0 SC T 0 + SC T0- SCR0 + SC R 0 - Si g nal GND Shield G ND Si g nal GND 35 37 45 39 44 38 40 46 47 49 50 43 48 J1 J2[...]

Cable, CompactFlash and Accessory Specifications A-12 T1/E1/ISDN PRI NIM Card Port s The T1/E1/ISDN PRI NIM comes equipped with either 1, 2 or 4 Ethernet (W AN) ports that support fractional T1/E1 transmissi on in full-channel, fractional or u nchannelized format with 8- pin modular RJ-48C connectors and includ e a built-in DSU/CSU, as shown in Fig[...]

Cable, CompactFlash and Accessory Specifications XSR Getting Started Guide A-13 Balun for E1 or PRI NIM Cards Some overseas electrical systems r equire that yo u use a balun and grounding shunt when utilizing an E1 or PRI NIM card on the XSR. A balun is an adapte r employed to connect a 75-ohm coaxial cable pair (2 BNC connectors) to a 120- ohm twi[...]

Cable, CompactFlash and Accessory Specifications A-14 Inst alling Shunt/T erminal Strip T o install the shunt or terminal strip, attach two dual-pin units vertically to each four-pin jumper (P2, P3, P4, or P5) corresponding to the RJ-48C port using a balun, as shown in Figure A-16 . Any other RJ-48C ports on the NIM car d connected to 120-ohm lines[...]

Cable, CompactFlash and Accessory Specifications XSR Getting Started Guide A-15 T3/E3 NIM Card The T3/E3 full and sub-rate NIM, as shown in Figur e A-17 , is equipped with 1 Ethernet (W AN) port that supports fractional T3 /E3 transm ission in un-channelize d or clear channel mode with BNC connectors. User data ar e encapsulated in HDLC packets bef[...]

Cable, CompactFlash and Accessory Specifications A-16 1/2-Port BRI-S/T NIM Card Port s The XSR offers a serial NIM car d for 1 or 2 W A N interfaces over an ISDN-S/T BRI line, as shown in Figure A -18 . Port 0 and 1 LEDs shine when the li nes are active and r eady to r eceive traf fic. Refer to Figure A-19 for pinout assignments. Figure A-18 ISDN B[...]

Cable, CompactFlash and Accessory Specifications XSR Getting Started Guide A-17 T ermination Shunt for the ISDN BRI-S/T NIM Card ISDN BRI-S/T terminal equipment devices may be connected at ra ndom points of the cable in point-to-point or point-to-multipoint configuratio ns. Line termination resistors must be pr ovided at both ends of the transmit/r[...]

Cable, CompactFlash and Accessory Specifications A-18 1/2-Port BRI-U NIM Card Port s The XSR provides a serial NIM car d for 1 or 2 W A N interfaces over an ISDN BRI-U line, as shown in Figure A- 21 . The Port 0 and 1 LEDs shine when the line s are active and ready to r eceive traffic. Figure A-21 ISDN BR I-U NI M Card (RJ-49C port s shown) Refer t[...]

Cable, CompactFlash and Accessory Specifications XSR Getting Started Guide A-19 1-Port ADSL NIM Card Port The XSR’s Asymmetric Digital Subscriber Line (A DSL) NIM card, as shown in Figur e A-23 , provides 1 W AN port on an ADSL over POTS (A nnex A/C) or ISDN (Annex B) line with a 6-pin RJ-1 1 connector . The ADSL NIM supports both G. dmt and G.li[...]

Cable, CompactFlash and Accessory Specifications A-20 T1/E1 Drop & Insert (D&I) NIM The XSR’s 2-port T1/E1 D& I NIM card, as shown in Figur e A-25 , is designed as an intermed iary between the Central Of fice T1/E1 line and a PBX. It de-couples Channel Associated Si gnaling (CAS) and V oice DS0 timeslots and redirects them to a PBX, a[...]

Cable, CompactFlash and Accessory Specifications XSR Getting Started Guide A-21 Comp actFlash Memory Card The optional plug-in CompactFlash (CF) memory card, shown in Figure A-27 , comprises a single chip controller and flash memory modules in a matchbook-sized package with a 50-pin, PC MCIA connector consisting of two r ows of 25 female contacts e[...]

Cable, CompactFlash and Accessory Specifications A-22 PWR ON XSR is powered up and Bootrom initi alized OFF XSR is powered down VPN ON/OFF VPN tunnel is up/No tunnel con nected COM(munication) Blinking/OFF Port is transmitting or receiving data/idle Ethernet Port 1, 2, 3 Amber only ON 10Base-T link is auto-detected Green only ON 100Base-T link is a[...]

Index-1 Index B Balun description A-13 Balun adapter A-3 BRI S/T card part numbers A-3 BRI S/Tpin assignments A-16 BRI U card part numbers A-3 BRI-U pin assignme nts A-18 , A-19 , A-20 Broadcom 1250 processor 1-2 C cable/accessory guide A-2 cabling part numbers A-2 Canadian notices iii channelized card specifications A-3 chassis dimensions 1-2 spec[...]

Index-2 how to attach the Ethernet serial cable 2-10 how to attach the internal power supply cord 2-12 how to attach the serial COM (console) cable 2-7 how to attach the WAN cables 2-7 how to configure Frame Relay 3-15 how to configure IP routing 3-14 how to configure the C OM port A-4 how to enable Web access 3-18 how to install a Co mpactFlash ca[...]