Essick Air ECR 4000 manual

ESSICK AIR PRODUCTS LITTLE ROCK, ARKANSAS 72209 50209-3 O WNERS MANU AL MODEL NO . ECR 3301 ECR 4000 ECR 4500 ECR 5200 ECR 6600 ECR 7200 CA UTION: Read All Instructions Carefully Bef ore Star ting The Installation. ESSICK CONVER TIBLE DO WN/FR ONT OUTLET EV APORA TIVE AIR COOLER[...]

2 INST ALLA TION T ools and Supplies Y ou Need ......................................... 3 Saf ety Rules ................................................................... 3 Data ................................................................................ 3 Locating Y our Cooler ...................................................... 4 Conv er [...]

3 T OOLS AND SUPPLIES Y OU WILL NEED • Pliers • Screwdriv ers • Adjustable Wrenches • T ubing Cutter • 5 / 32 He x Ke y Wrench • Electric Dr ill • Drill Bits • Hammer • Duct Caulking • #10 Sheet Metal Screws • Wiring Supplies, as Required by Local Electrical Code •L e v e l • Duct. As Required (a local sheetmetal shop can [...]

4 LOCA TING Y OUR COOLER This new design Essic k cooler may be installed as a bot- tom or side air outlet cooler . The cooler must be securely f astened to a frame or pad mount. A roof kit is av ailable from Essick. A duct must be attached to the cooler outlet. The duct must be the same size as the cooler outlet. Sudden duct size changes will decre[...]

5 1. Remove both louv ers and set them where they will not fall. See pg. 11. 2. Remove f our louver clips on side opposite motor . 3. Remov e a reser voir b y pushing the water crossov er tube from the grommet and lifting out the reservoir . 4. Remov e the second reser voir as abov e. 5. Remove the scre w that holds the wir ing box. 6. Remov e 1 / [...]

6 INST ALLA TION Lift at cabinet cor ners. The cooler may be lifted by putting a bar or strap through the panel hole and lifting by means of the bar or strap . LIFTING COOLER CA UTION: DO NO T LIFT ON THE LOUVERS. REMO VE THE LOUVERS BEFORE LIFTING. DO NO T LIFT ON THE CENTER OF THE CABINET FLANGES. MOUNTING COOLER 1. Prepare duct to fit model used[...]

7 INST ALLA TION ELECTRICAL CONNECTIONS The wiring must comply with local codes. If you are not f amiliar with the codes or wiring practices, get prof essional help. Use only an Essick ECR-5 or ECR-7 w all mounted switch. This new cooler does not require pre wetting the pads bef ore star ting cooling and does not hav e a pump . Existing switches wi[...]

8 INST ALLA TION FINAL ASSEMBL Y AND ADJUSTMENT PUT FLO A T V AL VE IN COOLER Put the float valv e through the spout hole and cabinet hole. Tighten the ring nut. Be sure the float mov es straight up and do wn. TURN THE FLO A T UNTIL A NARRO W SIDE IS UP . Snap the Splash Guard Cov er into the W ater Spout as shown. The W a ter Spout and Splash Guar[...]

9 IMPOR T ANT NO TE: When checking amperage with the ampmeter , all louv ers must be in place in the cooler , otherwise incorrect setting of the drive pulle y will occur . MO T OR PULLEY ADJUSTMENT NO TE: ALL DUCT CONNECTED COOLERS MUST BE ADJUSTED . Long or small air ducts hav e e xcessive air resistance which decreases air output and motor ampera[...]

10 HO W Y OUR COOLER WORKS Y our cooler evaporates water to cool air . Evaporative air cooling is the same natural cooling that happens when a breeze springs up after a summer shower . Y ou f eel cool because the rain water e vaporates and carries aw ay heat. Y our new cooler has a motor (1) driv en blower (2) which dra ws outside air through pads [...]

11 CARE OF Y OUR COOLER NEVER WEAR SHOES WITH SLICK SOLES WHEN Y OU W ORK ON A ROOF . Y OU MA Y SLIP WHEN Y OU LEAST EXPECT IT . NEVER DRAIN W A TER ONTO A R OOF . W A TER RESIDUE MA Y CA USE Y OU T O SLIP OR MA Y ST AIN Y OUR ROOF . USE A DRAIN HOSE T O R UN W A TER TO A RAIN GUTTER OR T O THE GROUND . F ALL CARE: Drain the cooler and water line t[...]

12 Operation of Roto Belt Coolers in “Hardwater” Areas. 1. Clean the cooler frequently . 2. Remov e mineral buildup from water troughs and Roto Belt to prev ent clogging. 3. A water analysis will determine: mineral content, what water treatments can be used, what cleaning agents should be used. 4. A “ bleed-off ” kit (Stock No . 8C190) shou[...]

13 REPLA CEMENT P ADS MODEL NUMBER P AD NUMBER ECR 3301 EP-30 ECR 4000 EP-40 ECR 4500 EP-40 ECR 5200 EP-50 ECR 6600 EP-60 PUTTING ON NEW P AD (Fig. 20) THE P ADS NEED NO PREWETTING. 1. Put the lower roller in pad. 2. Fit the low er roller into the bottom slots in the frame. 3. Push the top roller through the pad. Fit the roll end ov er the pad moto[...]

14 ESSICK CONVERTIBLE DO WN/FRONT OUTLET EV APORA TIVE AIR COOLER MODEL NOS. ECR 3301, ECR 4000, ECR 4500, ECR 5200, ECR 6600, ECR 7200 REP AIR P ARTS[...]

15 ESSICK CONVERTIBLE DO WN/FRONT OUTLET EV APORA TIVE AIR COOLER MODEL NOS. ECR 3301, ECR 4000, ECR 4500, ECR 5200, ECR 6600, ECR 7200 NO TICE: Order by P AR T NUMBER, not by K ey Number . Refer to the bac k cover of this man ual for par ts ordering information. KEY P ART NUMBER NO. ECR 3301 ECR 4000/4500 ECR 5200 ECR 6600/7200 P ART NAME 1 30439 [...]

ESSICK AIR PRODUCTS 5800 MURR Y • LITTLE ROCK, ARKANSAS 72209 501-562-1094 owners manual MODEL NO . ECR 3301 ECR 4000 ECR 4500 ECR 5200 ECR 6600 ECR 7200 HO W T O ORDER REP AIR P ARTS ESSICK CONVER TIBLE DO WN/FR ONT OUTLET EV APORA TIVE AIR COOLER The model number of y our cooler will be found on a label fastened to the housing. WHEN ORDERING RE[...]