Exmark 4500-435 manual

ST ANDON For Serial Nos. 790,000 & Higher Part No. 4500-435 Rev . A[...]

Exmark reser ves the right to make changes or add improv ements to its products at an y time without incurring any obligation to make such changes to products man ufactured previousl y . Exmark, or its distributors and dealers, accept no responsibility f or v ariations which may be evident in the actual specications of its products and the state[...]

Introduction CONGRATULATIONS on the purchase of your Exmark StandOn. This product has been carefully designed and man ufactured to gi ve y ou a maxim um amount of dependability and years of trouble-free operation. This manual contains assembly , operating, maintenance, adjustment, and safety instr uctions for your StandOn. BEFORE OPERATING Y OUR MO[...]

Contents Introduction . . . . . .. . . . . . . . . . . .. . . . . . . . . . . .. . . . . . . . . . . .. . . . . . . . . . .. .. . . . 3 Safety .. . . . .. .. . . .. .. . . .. . . . . . . . . . . .. . . . . . . . . . .. .. . . .. .. . . .. .. . . .. . . . . . . . . . 5 Safety Alert Symbol . . .. . . . . . . . . . .. .. . . .. .. . . .. .. . . .. . .[...]

Safety Safety Safety Alert Symbol This Safety Alert Symbol (Figure 2) is used both in this man ual and on the mac hine to identify important safety messages which m ust be follow ed to av oid accidents This symbol means: ATTENTION! BECOME ALERT! Y OUR SAFETY IS INV OL VED! Figure 2 1. Safety alert symbol The safety alert symbol appears abov e infor[...]

Safety DANGER Operating on wet grass or steep slopes can cause sliding and loss of control. Loss of control and/or loss of operator’s footing could result in a fall with an ar m or leg getting under the mow er or engine deck which may result in serious injur y , death or drowning . • Mow across slopes, nev er up and down. • Do Not mow slopes [...]

Safety Safety and Instructional Decals • Keep all safety signs legible . Remo ve all grease, dirt and debris from safety signs and instr uctional labels . • R eplace all w orn, damag ed, or missing safety signs . • When replacement components are installed, be sure that current safety signs are afx ed to the replaced components . • If an[...]

Specications Specications Model Numbers Serial Nos: 790,000 and Higher ST ANDON Dimensions Length Width Height W eight 35.4 inches (89.9 cm) 18.5 inches (47.0 cm) 14.9 inches (37.9 cm) 50 lb (23kg) T ire T read Size Semi-Pneumatic Tire Smooth 11 x 4.00–5 F or Operators o ver 250 lb it is recommended to use pneumatic tire assembly P/N 103-37[...]

Setup Setup Assembly Diagram Item Quantity Description 1 8 Nut, Nyloc 3/8-16 Flg 2 2 Plate, Back-Up 3 2 Plate, Adapter 4 8 Screw , HH 3/8-16 x 1 1/4 5 1 Asm, F rame Pull W/Decals 6 1 Asm, Pull Arm W/Brgs 7 1 Guard, T op 8 1 Screw , HH 3/8–16 x 4 3/4 9 1 Nut, Hex Flg-Side Loc k 3/8-16 10 1 Asm, Sulky F rame W/Decals 11* 2 Decals , R eplacement (T [...]

Setup Installing the StandOn Rider to Mower Mounting the Pull Frame 1. Locate the pull frame and tw o adapter plates . Install the pull frame to the adapter plates using four 3/8-16 x 1 1/4 inc h hex capscrews and four 3/8-16 inch nyloc nuts as shown in Figure 4. 3 4 4 2 1 1 2 G009397 Figure 4 1. 3/8-16 inch nyloc nuts 2. Adapter plate 3. Pull fram[...]

Setup Figure 7 1. Replacement decals e. Align the pull frame and adapter plate assembly to the rear surface of the engine deck. Measure the distance from the bottom of the pull frame to the g round. Choose the mount holes that will attain a distance appro ximately 8 inc hes (20 cm). Install the mount brac kets to the mow er engine dec k using tw o [...]

Setup Figure 10 1. Pull arm assembly 3. Pull frame 2. Quick connect pins 2. R emov e the 3/8-16 x 4 3/4 inc h hex capscrew . spring disc w asher , and 3/8-16 inc h hex ange side loc k n ut from the piv ot hub . 3. Locate the sulky frame assembly and align with the pull ar m assembly . R e-install the 3/8-16 x 4 3/4 inc h hex capscrew , spring di[...]

Operation Operation Note: Deter mine the left and right sides of the machine from the nor mal operating position. Pre-Start 1. Make sure y ou understand the controls , their locations , their functions , and their safety requirements . 2. Practice operating the machine without the StandOn until familiar with the controls . 3. Practice operating the[...]

Maintenance Maintenance Note: Deter mine the left and right sides of the machine from the normal operating position. W ARNING While maintenance or adjustments are being made, someone could star t the engine. Accidental star ting of the engine could seriously injure y ou or other bystanders. Remo ve the k ey from the ignition s witch, engage parking[...]

Maintenance Lubricate Caster Wheel Hubs Service Interval: Y early 1. Stop engine , w ait for all mo ving parts to stop , and remov e key . Engag e parking brake . Figure 13 1. Seal guard 2. Spacer nut with wrench ats 2. R emov e the caster wheel from the sulky frame . 3. R emov e seal guards from the wheel hub . 4. R emov e one of the spacer nut[...]

Maintenance Adjustments Adapter Plate and T ire Adjustment Important: F or optimal perfor mance, the StandOn pull ar m top surface should be horizontal to the ground surface. T o obtain a horizontal pull ar m, the adapter plates and the platfor m wheel can be repositioned (see Figure 14). Figure 14 1. Adapter plates can be moved to adjust height po[...]

Conditions and Products Co vered Exmark Mfg. Co. Inc. and its aff iliate, Ex mark W arranty Company , pursuant to an agreement between them, jointly warrant on the terms and conditions herein, that we will repair , replace or adjust any part on these products and found by us (in the ex ercise of our reasonable discretion) to be defective in factory[...]

Service Record Date: Description of Work Done: Service Done By: 18[...]

19[...]

MID-MOUNT RIDING A CCESSORIES AND OPTIONS SEE EXMARK’S COMPLETE LINE OF A CCESSORIES AND OPTIONS W ALK-BEHIND A CCESSORIES AND OPTIONS GRASS CA TCHER MICRO-MULCH SYSTEM TURF STRIPER ST ANDON CUST OM RIDE SEA T SUSPENSION SYSTEM FULL SUSPENSION SEA T DECK LIFT ASSIST KIT HITCH KIT LIGHT KIT 12 V PO WER POR T MICRO-MULCH SYSTEM OPERA T OR CONTROLLE[...]