Extron electronic XTP T UWP 202 manual

User Guide XTP T UWP 202 XTP Extender T wo Input XTP T ransmitter – Decora ® W allplate 68-2033-01 Rev . A 03 14[...]

Safety Instructions • English WARNING: This symbol, , when used on the product, is intended to alert the user of the presence of uninsulated danger ous voltage within the product’ s enclosure that may pr esent a risk of electric shock. A TTENTION: This symbol, , when used on the product, is intended to alert the user of important operating and [...]

FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part15 of the FCC rules. The ClassA limits provide r easonable protection against harmful interfer ence when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radi[...]

Conventions Used in this Guide Notifications The following notifications are used in this guide: W ARNING: A warning indicates a situation that has the potential to result in death or severe injury . CAUTION: A caution indicates a situation that may result in minor injury . A TTENTION: Attention indicates a situation that may damage or destroy the [...]

Contents SIS Configuration and Control ..................... 18 Host Device Connection ................................... 18 SIS Programming Guide ................................... 18 Host-to-Device and Device-to-Host Communication ........................................... 18 Device-Initiated Message .............................. 18 Error Re[...]

XTP T UWP 202 W allplate T ransmitter • Contents vi[...]

XTP T UWP 202 W allplate T ransmitter • Intr oduction 1 Intr oduction This section contains general information about this guide and the Extron XTP T UWP 202 W allplate T ransmitter , and selected device features. T opics in this section include: • About this Guide • About the XTP T UWP 202 • Key Features About this Guide This guide contain[...]

XTP T UWP 202 W allplate T ransmitter • Intr oduction 2 Figure 1 shows a typical point-to-point application of the XTP T UWP 202 with two input sources. PWR HDCP HDMI HDMI IN LAN VGA RESET CONFIG AUDIO CLIP AUTO SWITCH AUDIO IN VGA IN Ext ron XT P T UWP 20 2 Univ ersa l XT P T ransmit te r POWER 12V HDMI --A MAX Rx G Tx RS-232 IR R L Rx Tx - + - [...]

XTP T UWP 202 W allplate T ransmitter • Intr oduction 3 EDID Minder — Automatically manages EDID communication between connected devices to ensure that all sour ces properly power up and reliably display content. Key Minder — Authenticates and maintains continuous HDCP encryption between input and output devices to ensure quick and r eliable [...]

XTP T UWP 202 W allplate T ransmitter • Installation and Operation 4 Installation and Operation This section contains information for mounting, connecting, and wiring the XTP T UWP 202. T opics in this section include: • Installation Overview • Installing the Metal Junction Box or Mud Ring • Rear and Side Panel Connectors • Mounting the X[...]

XTP T UWP 202 W allplate T ransmitter • Installation and Operation 5 4. Route and connect cables to the rear and side panel connectors (see Rear and Side Panel Connectors on page 7). 5. Mount the XTP T UWP 202 to the mud ring or metal junction box (see Mounting the XTP T UPW 202 on page 9). 6. Connect inputs to the front panel connectors (see Fr [...]

XTP T UWP 202 W allplate T ransmitter • Installation and Operation 6 Installing the Mud Ring Backing Clip Mounting Sc re w Rotate the backing clip out of the way to insert the mud ring into the wall. Figure 2. Installing the Mud Ring with Backing Clips 1. Place 1.25 inches (3.18 cm) long or 0.75 inch (1.90 cm) #6-32 thread machine scr ews through[...]

XTP T UWP 202 W allplate T ransmitter • Installation and Operation 7 Installing a UL Listed Metal Junction Box Metal junction boxes may differ slightly fr om model to model. Check with the manufacturer for specific installation instructions. A TTENTION: Use metal junction boxes only . Signal Output Cable Cable Clam p Screws or Nails Wall opening [...]

XTP T UWP 202 W allplate T ransmitter • Installation and Operation 8 A XTP output connector — Connect a twisted pair cable to the RJ-45 connector labeled XTP Out on the XTP T UWP 202 and the XTP input port on another XTP device to pass all signals (see TP Cable T ermination and Recommendations on page 12). This cable carries the following signa[...]

XTP T UWP 202 W allplate T ransmitter • Installation and Operation 9 Mounting the XTP T UWP 202 NOTE: If desired, connect a host device to the fr ont panel Config port (see figure 8 , E ) befor e mounting to configure the transmitter (see SIS Configuration and Control on page 18 or XTP System Configuration Softwar e on page 23). Disconnect the ho[...]

XTP T UWP 202 W allplate T ransmitter • Installation and Operation 10 Fr ont Panel Connectors PWR HDCP HDMI HDMI IN LAN VGA RESET CONFIG AUDIO CLIP AUTO SWITCH AUDIO IN VGA IN A D B C E A HDMI input connector B Analog audio input connector C Analog video input connector D LAN connector (LAN models only) E Configuration port Figure 8. Front Panel [...]

XTP T UWP 202 W allplate T ransmitter • Installation and Operation 11 Selected Video Input HDMI Embedded Audio Present Analog Audio Present Audio Sent Over XTP VGA N/A Ye s Analog audio VGA N/A No No audio HDMI Ye s No HDMI embedded audio HDMI Ye s Ye s HDMI embedded audio HDMI No Ye s Analog audio HDMI No No No audio C Analog video input connect[...]

XTP T UWP 202 W allplate T ransmitter • Installation and Operation 12 TP Cable T ermination and Recommendations Use the following pin configurations for twisted pair cables. 12345678 RJ-45 Connector Inser t T wisted P air Wires Pins: Pin 1 2 3 4 5 6 7 8 Wire color White-green Green White-orange Blue White-blue Orange White-brown Brown Wire color [...]

XTP T UWP 202 W allplate T ransmitter • Installation and Operation 13 RS-232 and IR Over XTP Communication The RS-232 and IR Over XTP connector is for pass-through transmission of serial signals, such as projector contr ol signals, and infrared data. T o pass bidirectional serial command signals between XTP-compatible devices, connect a control d[...]

XTP T UWP 202 W allplate T ransmitter • Installation and Operation 14 Power Connection Apply power to the transmitter locally with the provided power supply or r emotely with a power injector or an XTP matrix switcher . A TTENTION: XTP remote power is intended for indoor use only . No part of the network that uses XTP remote power should be r out[...]

XTP T UWP 202 W allplate T ransmitter • Installation and Operation 15 Remote power The XTP T UWP 202 can be powered r emotely through an XTP Power Injector or through an XTP matrix switcher . A TTENTION: XTP remote power is intended for indoor use only . No part of the network that uses XTP remote power should be r outed outdoors. Power injector [...]

XTP T UWP 202 W allplate T ransmitter • Installation and Operation 16 Operation After all transmitters, all receivers, and their connected devices ar e powered up, the system is fully operational. If any problems ar e encountered, verify that the cables are r outed and connected properly . If problems persist, call the Extron S3 Sales & T ech[...]

XTP T UWP 202 W allplate T ransmitter • Installation and Operation 17 Reset Modes PWR HDCP HDMI HDMI IN LAN VGA RESET CONFIG AUDIO CLIP AUTO SWITCH AUDIO IN VGA IN A Figure 16. Reset Button (LAN Model Shown without the Decora Faceplate) Use the recessed Reset button on the fr ont panel of the transmitter to return the device to default settings o[...]

XTP T UWP 202 W allplate T ransmitter • SIS Configuration and Contr ol 18 SIS Configuration and Contr ol The XTP T UWP 202 can be configured and contr olled using Extron Simple Instruction Set (SIS) commands or the XTP System Configuration Software (see XTP System Configuration Software on page 23). This section contains basic SIS communication d[...]

XTP T UWP 202 W allplate T ransmitter • SIS Configuration and Contr ol 19 Error Responses When the XTP T UWP 202 receives an SIS command and determines that it is valid, it performs the command and sends the corresponding r esponse to the host device. If the command is determined invalid or contains invalid parameters, the switcher returns an err[...]

XTP T UWP 202 W allplate T ransmitter • SIS Configuration and Contr ol 20 Command and Response T ables for SIS Commands Command ASCII Command (Host to Device) Response (Device to Host) Additional Description Input Commands Input selection Select input X! ! In X!] Select input X! . View the selected input ! In X! ] V iew the selected input. Auto s[...]

XTP T UWP 202 W allplate T ransmitter • SIS Configuration and Contr ol 21 Command ASCII Command (Host to Device) Response (Device to Host) Additional Description Black signal for audio only NOTE: The switcher uses a black signal to simulate a 720p or 1080p, 50 Hz or 60 Hz signal so audio can be passed without video. Enable black signal E B1AFMT }[...]

XTP T UWP 202 W allplate T ransmitter • SIS Configuration and Contr ol 22 Command ASCII Command (Host to Device) Response (Device to Host) Additional Description EDID Commands NOTE: For EDID management, use the XTP System Configuration Software (see EDID Minder on page 34). Advanced Configuration Commands HDCP authorized device (HDMI input only) [...]

XTP T UWP 202 W allplate T ransmitter • XTP System Configuration Softwar e 23 XTP System Configuration Softwar e This section contains installation and configuration procedur es for the XTP System Configuration Software for configuring and contr olling the XTP T UWP 202. It can also be controlled with SIS commands (see SIS Configuration and Contr[...]

XTP T UWP 202 W allplate T ransmitter • XTP System Configuration Softwar e 24 Using the XTP System Configuration Softwar e The XTP T UWP 202 can be controlled dir ectly from the front panel Config port or r emotely from an XTP matrix switcher . Connections When opening the XTP System Configuration Software, the Connections scr een opens first. Th[...]

XTP T UWP 202 W allplate T ransmitter • XTP System Configuration Softwar e 25 T op Menu The top menu bar contains three menus for configuring softwar e settings. File menu The File menu contains options for disconnecting from the transmitter and exiting the program. T o access the menu, click the File menu. Figure 20. File Menu Disconnect This op[...]

XTP T UWP 202 W allplate T ransmitter • XTP System Configuration Softwar e 26 Update Firmware This option uploads firmware fr om the host device to the connected device. NOTE: If necessary , download new firmware fr om the Extron website (see Downloading Firmware on page 38). 1. From the Tools menu, select Update Firmware . A dialog box opens to [...]

XTP T UWP 202 W allplate T ransmitter • XTP System Configuration Softwar e 27 Help menu The Help menu contains a way to access XTP System Configuration Software information, a link to the help file, and a link to the Extron website. Figure 24. Help Menu NOTE: The Tutorial (System Configuration) option is not available when directly connected to t[...]

XTP T UWP 202 W allplate T ransmitter • XTP System Configuration Softwar e 28 Device Settings The Device Settings screen allows a user to view and edit various device settings for the device directly connected to the PC running the XTP softwar e. Click the Device Settings icon (see figure 26, 1 ) on the Global Navigation bar to open the Device Se[...]

XTP T UWP 202 W allplate T ransmitter • XTP System Configuration Softwar e 29 Input/Output tab Click the Input/Output tab (see figure 27, 1 ) to open the Input/Output scr een. It contains input information and options to apply automatic settings to individual inputs. Figure 27. Input/Output T ab 2 Input — Displays the input name. 3 Signal T ype[...]

XTP T UWP 202 W allplate T ransmitter • XTP System Configuration Softwar e 30 Analog Video tab Click the Analog Video tab (see figure 28, 1 ) to open the Analog Video scr een. It contains signal sampling, image shifting, and saving and recalling input pr eset options. Figure 28. Analog Video T ab Image Settings panel Signal sampling optimizes the[...]

XTP T UWP 202 W allplate T ransmitter • XTP System Configuration Softwar e 31 Audio tab Click the Audio tab (see figure 29, 1 ) to open the Audio scr een. It contains settings for audio input format and analog audio gain. Figure 29. Audio T ab Input format panel 2 Input format — From the Audio Format dr op-down list, select the format for input[...]

XTP T UWP 202 W allplate T ransmitter • XTP System Configuration Softwar e 32 General tab Click the General tab (see figure 30, 1 ) to open the General scr een. It contains settings for auto switch mode and factory reset. Figure 30. General T ab Auto-input Switching panel 2 Auto-input Switching — Click the Enable Auto-Input Switching check box [...]

XTP T UWP 202 W allplate T ransmitter • XTP System Configuration Softwar e 33 Device Information panel The Device Information panel on the right side of the software scr een displays device information and settings. General Information section 1 Model — Displays the device model. 2 Firmware version — Displays the full firmwar e version. Signa[...]

XTP T UWP 202 W allplate T ransmitter • XTP System Configuration Softwar e 34 EDID Minder Use the EDID Minder screen to assign unique EDID to the input or match curr ent output resolutions to the input. Click the EDID Minder icon (see figur e 31, 1 ) on the global navigation bar . The EDID Minder screen opens. The EDID Minder screen displays a ta[...]

XTP T UWP 202 W allplate T ransmitter • XTP System Configuration Softwar e 35 Import EDID 1. On the EDID Minder screen, click the Add EDID to Library button (see figur e 31, 8 ). The Browse window opens. 2. Select the desired EDID file and click Open . The EDID appears in the A vailable EDID panel (see figure 31, 4 ). 3. Assign the EDID from the [...]

XTP T UWP 202 W allplate T ransmitter • Refer ence Information 36 Refer ence Information This section contains mounting information and instructions for updating firmware. T opics in this section include: • Updating Firmware with Firmwar e Loader • Mounting T emplate Updating Firmwar e with Firmwar e Loader T o upload and update firmware for [...]

XTP T UWP 202 W allplate T ransmitter • Refer ence Information 37 Figure 34. Navigating to Firmwar e Loader 3. Click the F link and navigate to Firmware Loader (see figur e 34, 3 ). 4. Click the Download link on the right that corresponds with the pr ogram (see figure 34, 4 ). 5. Submit any requir ed information to start the download. Note where [...]

XTP T UWP 202 W allplate T ransmitter • Refer ence Information 38 Downloading Firmware Figure 35. Downloading Firmwar e from the Extron W ebsite 1. On the Extron website , click the Download tab (see figur e 35, 1 ). 2. On the left sidebar , click the Firmware link (see figure 35, 2 ). 3. Navigate to the XTP T UWP 202. 4. Ensure the available fir[...]

XTP T UWP 202 W allplate T ransmitter • Refer ence Information 39 Installing Firmware with Firmwar e Loader Use the Firmware Loader utility to upload firmwar e to the transmitter when connected directly to the device. 1. Connect the host device to the front panel USB port. 2. Open Firmware Loader and establish a connection between the computer an[...]

XTP T UWP 202 W allplate T ransmitter • Refer ence Information 40 Mounting T emplate Figure 37 is a example of a mounting template for pr eparing mounting surfaces. It is not to full size. 4.26" (10.83 cm) 4.28" (10.87 cm) Recommended cut-out area f or the installation surface. T op P anel SURF AC E CUT -OUT AREA FOR W ALL MOUNT 3.75&qu[...]

Extron Headquarters +1.800.633.9876 (Inside USA/Canada Only) Extron USA - W est Extron USA - East +1.714.491.1500 +1.919.850.1000 +1.714.491.1517 F AX +1.919.850.1001 F AX Extron Europe +800.3987.6673 (Inside Europe Only) +31.33.453.4040 +31.33.453.4050 F AX Extron Asia +65.6383.4400 +65.6383.4664 F AX Extron Japan +81.3.3511.7655 +81.3.3511.7656 F[...]