Gefen EXT-IP-2-RS2322 manual

Audio Embedder 3GSDI EXT-IP-2-RS2322 User Manual IP to RS-232 Converter *Pr eferred Release A1[...]

ii 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this product near water . 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer ’s instructions. 8. Do not install or place this product near any heat sources su[...]

iii Gefen warrants the equipment it manufactures to be free from defects in material and workmanship. If equipment fails because of such defects and Gefen is notied within two (2) years from the date of shipment, Gefen will, at its option, repair or replace the equipment, provided that the equipment has not been subjected to mechanical, electric[...]

iv T echnical S upport (818) 772-9100 (800) 545-6900 8:00 AM to 5:00 PM Monday - Friday , Pacic T ime Fa x (818) 772-9120 Email support@gefen.com We b http://www .gefen.com Mailing Addr ess Gefen, LLC c/o Customer Service 20600 Nordhoff St. Chatsworth, CA 9131 1 Pr oduct R egistr ation Register your product here: http://www .gefen.com/kvm/Regist[...]

v v Operating Notes • When using the IP to 2 x RS-232 Converter for the rst time, it is recommended that the unit be congured using the Gefen Discovery T ool. The Gefen Discovery T ool is free software that is available from the Support > Downloads section of the Gefen Web site. IP to 2 x RS-232 Converter is a trademark of Gefen, LLC. ©[...]

vi Features and Packing List Features • Allows IP control of two RS-232-enabled devices • Supports T elnet and UDP protocols • Each of the RS-232 devices can be addressed independently • Congurable via Web server interface • Independently congurable RS-232 baud rate and line delay for each RS-232 port • Gefen Discovery T ool-compa[...]

vii[...]

viii Table of Contents 1 Get ting St arted Introduction............................................................................................................ 2 Installation ............................................................................................................. 4 Connection Instructions ...................................[...]

[...]

[...]

IP to RS-232 Converter 1 Ge t ting St ar t ed Introduction............................................................................................................ 2 Installation ............................................................................................................. 4 Connection Instructions ................................[...]

page | 2 Introduction RS-232 1 Power IP Reset EXT -IP-2-RS2322 Gefen 5V DC IP control RS-232 2 IP to 2xRS-232 Converter RS-232 1 Power IP Reset EXT -IP-2-RS2322 Gefen 5V DC IP control RS-232 2 IP to 2xRS-232 Converter RS-232 1 Power IP Reset EXT -IP-2-RS2322 Gefen 5V DC IP control RS-232 2 IP to 2xRS-232 Converter 6 4 5 3 2 Getting S tart ed Gettin[...]

page | 3 Introduction ID Name Description 1 IP Reset Resets the unit to its default IP settings. 2 RS-232 1 Connect an RS-232 cable from this port to an RS-232 device. See Installation (page 4 ) for more information. 3 Power This LED will glow bright blue when the unit is powered. 4 5V DC Connect the included 5V DC power supply to this power recept[...]

page | 4 Installation Getting S tart ed Connection Instructions 1. Connect an Ethernet cable between the IP-based control device and the IP control port on the IP to 2 x RS-232 Converter . An Ethernet switch can also exist between the IP to 2 x RS-232 Converter and the IP-based control device (see Sample Wiring Diagram below). 2. Connect an RS-232 [...]

[...]

[...]

page | 7 IP to RS-232 Converter 2 A dv anced Oper ation RS-232 and IP Conguration ................................................................................ 8 Conguration using the Gefen Discovery Tool .............................................. 8 Conguration using RS-232 ...........................................................[...]

page | 8 RS-232 and IP Conguration Adv anced Oper ation Adv anced Oper ation Configuration using the Gefen Discovery Tool When using the IP to 2 x RS-232 Converter for the rst time, it is recommended that the unit be congured using the Gefen Discovery T ool. The Gefen Discovery T ool is free software that is available from the Support >[...]

page | 9 Adv anced Oper ation Configuration using RS-232 T o congure the IP settings of the IP to 2 x RS-232 Converter using RS-232 commands, use the following procedure: 1. Connect a null-modem (“crossover”) cable from the RS-232 port on the computer to the IP to 2 x RS-232 Converter . The null-modem cable can be connected to either RS-232 [...]

page | 10 RS-232 and IP Conguration Adv anced Oper ation Adv anced Oper ation 5. Set the gateway (router) IP address using the #set_gateway command. 6. Set the T elnet listening port using the #set_tcp_term_port command. 7. Set the HTTP listening port using the #set_http_port command. 8. Set the UDP remote IP address using the #set_udp_rip comma[...]

page | 1 1 Adv anced Oper ation Command Description #help Displays a list of all available commands #set_add_delim Enables or disables option to add delimiter to data #set_device_descr Sets the device description #set_end_del Sets the end frame delimiter #set_gateway Sets the gateway (router) IP address #set_http_port Sets the HTTP listening port o[...]

page | 12 Adv anced Oper ation Adv anced Oper ation Commands Command Description #show_serial_params Displays the settings of the specied RS-232 port #show_telnet_pass Displays the current TCP terminal password #show_ver_data Displays the rmware and hardware version of the IP to RS-232 Converter #system_wide_reset Restarts the IP to 2 x RS-23[...]

page | 13 Adv anced Oper ation Commands #help Displays help on a specic command. If no command is specied ( param1 ), then a list of all available commands will be displayed. Set param1 to “full” to display a list of all commands. S yntax #help P ar amet ers param1 Command (optional) Example #help #set_add_delim Cmd #set_add_delim: Set Ad[...]

page | 14 Commands Adv anced Oper ation Adv anced Oper ation #help #show_ipcong #set_ipadd #set_netmask #set_gateway #set_http_port #set_tcp_term_port #set_udp_port #show_ver_data #show_telnet_pass #set_telnet_pass #use_tcp_term_pass #set_udp_rip #set_udp_rport #use_udp_access #use_udp_echo #use_tcp_access #set_serial_params #show_serial_params [...]

page | 15 Commands Adv anced Oper ation #set_add_delim Enables or disables the option to include a delimiter as part of the data sent to the control system. S yntax #set_add_delim param1 param2 P ar amet ers param1 V alue [1 ... 2] param2 State [0 ... 1] V alue Description 0 Off 1 On Example #set_add_delim 1 Add delimiter mode to ON R elated C omma[...]

page | 16 Commands Adv anced Oper ation Adv anced Oper ation #set_device_descr Sets the device description. The device description cannot exceed 30 characters in length S yntax #set_device_descr param1 P ar amet ers param1 Description [30 chars max.] Example #set_device_descr LivingRoom_Bridge2 Device Description changed to: LivingRoom_Bridge2 R el[...]

page | 17 Commands Adv anced Oper ation #set_end_del Sets the end-delimiter mode and value for the specied serial port. The End Delimiter value must be specied in hexadecimal. Before executing this command, the Start Delimiter must be set, using the #set_start_del command. S yntax #set_end_del param1 param2 param3 P ar amet ers param1 Serial [...]

page | 18 Commands #set_gateway Sets the gateway address. The gateway must be typed using dot-decimal notation. The matrix must be rebooted after executing this command. The default gateway is 192.168.1.1 . S yntax #sgateway param1 P ar amet ers param1 Gateway Example #set_gateway 10.5.64.1 New IP Gateway set to: 10.5.64.1 R elated C ommands #set_a[...]

page | 19 Commands #set_http_port Species the Web server listening port. The unit must be rebooted after executing this command. The default port setting is 80 . S yntax #set_http_port param1 P ar amet ers param1 Port [1 ... 1024] Example #set_http_port 82 New HTTP port set to: 82 R elated C ommands #set_gateway #set_ipadd #set_netmask #show_ipc[...]

page | 20 Commands #set_ipadd Species the IP address of the IP to 2 x RS-232 Converter . The IP address must be specied using dot-decimal notation. The unit must be rebooted after executing this command. The default IP address is 192.168.1.72 . S yntax #set_ipadd param1 P ar amet ers param1 IP address Example #set_ipadd 10.5.64.187 New IP set[...]

page | 21 Commands #set_netmask Sets the subnet mask. The subnet mask must be entered using dot-decimal notation. The unit must be rebooted after executing this command. The default net mask is 255.255.255.0 . S yntax #snetmask param1 P ar amet ers param1 Net mask Example #snetmask 255.255.0.0 New IP Mask set to: 255.255.0.0 R elated C ommands #set[...]

page | 22 Commands #set_send_byte_cnt Sets the send-byte count value for bridging mode. S yntax #set_send_byte_cnt param1 P ar amet ers param1 Serial port [1 ... 2] param2 Byte count [0 ... 255] Example #set_send_byte_cnt 1 100 UART 1 bridging send byte count limit is set to 100 bytes R elated C ommands #set_add_delim #set_end_del #set_serial_mode [...]

page | 23 Commands #set_send_time_out Sets the time-out value for sending data collected from a device to the control system in Bridging Mode when a Start Delimiter and End Delimiter have been set. If no data has been collected for the specied time, the data is sent without waiting for the End Delimiter . S yntax #set_send_time_out param1 P ar a[...]

page | 24 Commands #set_serial_descr Assigns a descriptor to the specied serial port. The serial port description cannot exceed 20 characters in length. The default description is None . S yntax #set_serial_descr param1 param2 P ar amet ers param1 Port [1 ... 2] param2 Description [20 chars max.] Example #set_serial_descr 1 DVD_Ctrl Serial port [...]

page | 25 Commands #set_serial_mode Sets the mode of the specied serial port. The default mode for all serial ports (1 - 2) is TCP Bridge mode. S yntax #set_serial_mode param1 param2 P ar amet ers param1 Port [1 ... 2] param2 State [1 ... 3] Mode Description 1 TCP bridge 2 UDP bridge 3 T erminal mode Example #set_serial_mode 1 2 Serial port 1 wo[...]

page | 26 Commands Adv anced Oper ation Adv anced Oper ation #set_serial_params Assigns the settings to the specied serial port. S yntax #set_serial_params param1 param2 param3 param4 param5 param6 P ar amet ers param1 Port [1 ... 3] param2 Word length [5 ... 8] param3 Stop bits [1 ... 2] param4 Parity Parity Description n None e Even o Odd m Ma[...]

page | 27 Commands Adv anced Oper ation Example #set_serial_params 1 8 1 N 19200 1000 Serial port 1 parameters: Word length = 8 bits Stop bits = 1 bit Parity = None Baud Rate = 19200 Bps Line Delay = 1000 ms R elated C ommands #show_serial_params[...]

page | 28 Commands Adv anced Oper ation Adv anced Oper ation #set_start_del Sets the Start Delimiter mode and value for the specied serial port. The Start Delimiter must always be specied before the End Delimiter . S yntax #set_start_del param1 param2 param3 P ar amet ers param1 Serial port [1 ... 2] param2 State [0 ... 1] Mode Description 1 [...]

page | 29 Commands Adv anced Oper ation #set_tcp_br_port Sets the TCP bridge listening port for the specied serial port. The default port settings for RS-232 1 and RS-232 2 ports are 49200 and 49201, respectively . S yntax #set_tcp_br_port param1 param2 P ar amet ers param1 Serial port [1 ... 2] param2 TCP port [1 ... 65535] Example #set_tcp_br_[...]

page | 30 Commands Adv anced Oper ation Adv anced Oper ation #set_tcp_term_port Sets the TCP terminal listening port. The default port settings is 23 . S yntax #set_tcp_term_port param1 P ar amet ers param1 TCP port [1 ... 65535] Example #set_tcp_term_port 23 New TCP Terminal port set to: 23 R elated C ommands #set_tcp_br_port #set_udp_br_port[...]

page | 31 Commands Adv anced Oper ation #set_telnet_pass Sets the TCP T erminal password. The password cannot exceed 20 characters in length. param3 is used to verify the new password. The default password is Admin . S yntax #set_telnet_pass param1 param2 param3 P ar amet ers param1 Old password [20 chars max.] param2 New password [20 chars max.] p[...]

page | 32 Commands Adv anced Oper ation Adv anced Oper ation #set_udp_br_port Sets the UDP bridge listening port. The default UDP bridge port settings for RS-232 1 and RS-232 2 ports are 50200 and 50201, respectively . S yntax #set_udp_br_port param1 param2 P ar amet ers param1 Serial port [1 ... 2] param2 Port [1 ... 65535] Example #set_udp_br_por[...]

page | 33 Commands Adv anced Oper ation #set_udp_echo_br Enables or disables UDP bridge echo. S yntax #set_udp_echo_br param1 param2 P ar amet ers param1 Serial port [1 ... 2] param2 State [0 ... 1] State Description 0 Disabled 1 Enabled Example #set_udp_echo_br 1 1 The echo of UDP Bridge port 1 is enabled R elated C ommands #set_udp_br_port #set_u[...]

page | 34 Commands Adv anced Oper ation Adv anced Oper ation #set_udp_port Sets the UDP server listening port S yntax #set_udp_port param1 P ar amet ers param1 Serial port [1 ... 65535] Example #set_udp_port 50007 New UDP server port set to: 50007 R elated C ommands #set_udp_br_port #set_udp_remote_br #set_udp_echo_br #set_udp_rip #set_udp_rport[...]

page | 35 Commands Adv anced Oper ation #set_udp_remote_br Assigns the UDP Bridge settings for the specied serial port. param2 must be entered in dot-decimal notation. S yntax #set_udp_remote_br param1 param2 param3 P ar amet ers param1 Serial port [1 ... 2] param2 Address param3 Remote port [1 ... 65535] Example #set_udp_remote_br 1 192.168.1.7[...]

page | 36 Commands Adv anced Oper ation Adv anced Oper ation #set_udp_rip Sets the remote UDP IP address. The IP address must be entered using dot-decimal notation. Each digit can range between 0 and 255. S yntax #set_udp_rip param1 P ar amet ers param1 IP address Example #set_udp_rip 192.168.1.205 New Remote UDP IP set to: 192.168.1.205 R elated C[...]

page | 37 Commands Adv anced Oper ation #set_udp_rport Sets the remote UDP listening port. The default port settings is 50008 . S yntax #set_udp_rport param1 P ar amet ers param1 Port [1 ... 65535] Example #set_udp_rport 50006 New UDP Remote port set to: 50006 R elated C ommands #set_udp_br_port #set_udp_echo_br #set_udp_remote_br #set_udp_rip[...]

page | 38 Commands Adv anced Oper ation Adv anced Oper ation #show_del_prms Displays the current delimiter parameters for the specied serial port. S yntax #show_del_prms param1 P ar amet ers param1 Port [1 ... 2] Example #show_del_prms 1 Delimiter Param’s in bridge mode, UART 1 Line Delay = 1000ms Time To Force Send = 30ms Count Byte To Force [...]

page | 39 Commands Adv anced Oper ation #show_device_descr Displays the device description. S yntax #show_device_descr P ar amet ers None Example #show_device_descr Device Description: IP_BRIDGE R elated C ommands #set_device_descr[...]

page | 40 Commands Adv anced Oper ation Adv anced Oper ation #show_ipcong Displays the current TCP/IP and UDP settings. S yntax #show_ipcong P ar amet ers None Example #show_ipcong --------- IP to 2 x RS-232 Converter settings --------- MAC addr = 00:1C:91:01:0F:FF IP addr = 10.5.64.254 Net Mask = 255.255.255.0 Gateway = 192.168.1.254 Web [...]

page | 41 Commands Adv anced Oper ation #show_me Enables or disables the ashing of the LED on the device. When enabled, the LED indicator will ash red and blue. The default setting is disabled. S yntax #show_me param1 P ar amet ers param1 State State Description 0 Disabled 1 Enabled Example #show_me 1 Show me is Enabled R elated C ommands #us[...]

page | 42 Commands Adv anced Oper ation Adv anced Oper ation #show_serial_descr Displays the description of the specied serial port. S yntax #show_serial_descr param1 P ar amet ers param1 Port [1 ... 2] Example #show_serial_descr 1 Serial port 1 Description: DVD_Ctrl R elated C ommands #set_serial_descr[...]

page | 43 Commands Adv anced Oper ation #show_serial_mode Displays the mode of the specied serial port. S yntax #show_serial_mode param1 P ar amet ers param1 Port [1 ... 2] Example #show_serial_mode 1 Serial port 1 working mode is: TCP Bridge Mode R elated C ommands #set_serial_mode[...]

page | 44 Commands Adv anced Oper ation Adv anced Oper ation #show_serial_params Displays the current settings of the specied serial port. S yntax #show_serial_params param1 P ar amet ers param1 Port [1 ... 2] Example #show_serial_params 1 Serial port 1 parameters: Word length = 8 bits Stop bits = 1 bit Parity = None Baud Rate = 19200 Bps Line D[...]

page | 45 Commands Adv anced Oper ation #show_telnet_pass Displays the current TCP terminal password. S yntax #show_telnet_pass P ar amet ers None Example #show_telnet_pass TCP Terminal password: b055man R elated C ommands #set_telnet_pass[...]

page | 46 Commands Adv anced Oper ation Adv anced Oper ation #show_ver_data Displays the current software and hardware version. S yntax #show_ver_data P ar amet ers None Example #show_ver_data Firmware version 1.48 Release date: May 12 2014 Release time: 14:09:37[...]

page | 47 Commands Adv anced Oper ation #system_wide_reset Restarts the IP to 2 x RS-232 Converter according to the supplied parameter . S yntax #system_wide_reset param1 P ar amet ers param1 V alue [0 ... 3] V alue Description 0 Reboot only 1 Reset IP settings 2 Reset serial port settings 3 Reset all and reboot Example #system_wide_reset 3 System [...]

page | 48 Commands Adv anced Oper ation Adv anced Oper ation #use_discovery Enables or disables discovery access mode. If this mode is disabled, then the IP to 2 x RS-232 Converter will not be discoverable when using the Gefen Discovery T ool. The default setting is enabled . S yntax #use_discovery param1 P ar amet ers param1 State State Descriptio[...]

page | 49 Commands Adv anced Oper ation #use_tcp_access Enables or disables TCP access mode. This mode must be enabled before using RS-232 command to congure the IP to 2 x RS-232 Converter . S yntax #use_tcp_access param1 P ar amet ers param1 V alue [0 ... 1] V alue Description 0 Disable TCP access 1 Enable TCP access Example #use_tcp_access 1 T[...]

page | 50 Commands Adv anced Oper ation Adv anced Oper ation #use_tcp_term_pass Enables or disables the use of the password during terminal sessions. S yntax #use_tcp_term_pass param1 P ar amet ers param1 V alue [0 ... 1] V alue Description 0 Do not use password 1 Require password Example #use_tcp_term_pass 1 TCP Terminal password at login is set t[...]

page | 51 Commands Adv anced Oper ation #use_udp_access Enables or disables UDP access. S yntax #use_udp_access param1 P ar amet ers param1 V alue [0 ... 1] V alue Description 0 Disable UDP access 1 Enable UDP access Example #use_udp_access 1 UDP Access is set to Enabled R elated C ommands #set_udp_br_port #set_udp_echo_br #set_udp_remote_br #set_u[...]

page | 52 #use_udp_echo Enables or disables UDP echo. S yntax #use_udp_echo param1 P ar amet ers param1 V alue [0 ... 1] V alue Description 0 Disable UDP echo 1 Enable UDP echo Example #use_udp_echo 1 UDP echo is set to Enabled R elated C ommands #set_udp_echo_br Commands Adv anced Oper ation Adv anced Oper ation[...]

page | 53 Adv anced Oper ation Web Interface Using the built-in Web Interface Access the built-in Web interface by entering the IP address of the IP to 2 x RS-232 Converter that was specied in step 3 under Conguration using RS-232 (page 9) . The built-in Web interface is divided into three pages: RS-232, Network, and System. Each main page is[...]

page | 54 Web Interface RS-232 Select RS-232 Port Select the RS-232 port from the drop-down list. Options: 1 , 2 Description Enter a description for the device that is connected to the selected RS-232 port. RS-232 Mode Select the desired mode from the drop-down list. Options: TCP Bridge , UDP Bridge , T erminal Adv anced Oper ation Adv anced Oper a[...]

page | 55 Web Interface Baud Rate Select the baud rate used by the RS-232 device from this drop-down list. Options : 1 10, 300, 600, 1200, 2400, 4800, 9600, 14400, 19200, 28800 Data Bits Select the number of data bits in each character from this drop-down list. For most applications, 8 data bits should be selected. 9 data bits are rarely used. Opti[...]

page | 56 Web Interface Line Delay (ms) Enter the line delay in this eld. Range : 0 ... 10000 Force Send (ms) If no data is received from the controlled device within the specied time interval, send the collected data to the control system. Range : 0 ... 30 Force Send (bytes) If the specied number of bytes is received from the controlled d[...]

page | 57 Web Interface Add Delimiters to data sent Include the delimiter characters in the data sent to the control system. Check the Add box to enable this feature. Options : Enable (checked), Disable (unchecked) Use Start Delimiter Includes the Start Frame Delimiter , used at the end of the preamble of an Ethernet frame. Options : Enable (checke[...]

page | 58 Web Interface End Delimiter V alue This value can be up to three ASCII characters (3 bytes), in length. The value must be entered in hexadecimal Range : 00 ... FF (“wildcard” characters, such as **, are acceptable) TCP Port Enter the TCP port in this eld. Range : 0 ... 65535 UDP Local Port Enter the UPD local port in this eld. R[...]

page | 59 Web Interface Destination IP Enter the destination (where the data will be sent) IP address in this eld. Range (per byte) : 0 ... 255 Destination Port Enter the destination port in this eld. Range : 1024 ... 65535 UDP Echo Useful in troubleshooting and measuring response times and end-to-end connectivity . Options : Enable (checked)[...]

page | 60 Web Interface Network tab MAC Address The MAC address of the IP to RS-232 Converter . The MAC address cannot be changed. Mode Select the network mode from the drop-down list. Options : Static , DHCP IP Address Enter the IP address of the IP to 2 x RS-232 Converter . Range (per byte) : 0 ... 255 Subnet Enter the subnet mask of the IP to 2 [...]

page | 61 Web Interface Gateway The gateway (router) IP address to with the IP to 2 x RS-232 Converter is connected. Range (per byte) : 0 ... 255 HTTP Port Select the network mode from the drop-down list. Range (per byte) : 1 ... 1024 Adv anced Oper ation[...]

page | 62 Web Interface Enable TCP Access Enables or disables TCP access. Options : Enable (checked) , Disable (unckecked) Require Password on Connect Forces password prompt for T elnet sessions. Options : Enable (checked) , Disable (unckecked) User Name Displays the user name for TCP sessions. The user name cannot be changed. Old Password T ype th[...]

page | 63 Web Interface New Password T ype the new password in this eld. The password is automatically masked when entered. The password is case-sensitive. Maximum length: 8 characters Conrm Password Re-type the new password in this eld. The password must match the same password that was entered in the New Password eld. Maximum length: [...]

page | 64 Web Interface Enable UDP Access Enables or disables UDP access. Options : Enable (checked) , Disable (unckecked) UDP Port Sets the UDP port. Range : 1 ... 1024 Enable UDP Echo Enables or disables UDP echo. Options : Enable (checked) , Disable (unckecked) Adv anced Oper ation Adv anced Oper ation[...]

page | 65 Web Interface Destination UDP IP Address Enter the remote UDP IP address in this eld. Range (per byte) : 0 ... 255 Destination UDP Port T ype the remote UDP port in this eld. Range : 1 ... 1024 Enable Discovery Enables or disables discovery mode. This feature must be enabled in order for the Gefen Discovery T ool to detect the unit [...]

page | 66 Web Interface Adv anced Oper ation Adv anced Oper ation System tab Download (Download Current Conguration) Saves the current conguration of the IP to 2 x RS-232 Converter to a le. Browse... (Restore Conguration) Selects the conguration le to load. See the Download button, above. Restore Click this button to upload the se[...]

page | 67 Web Interface Adv anced Oper ation Browse... (Firmware Update) Click this button to select the rmware le to be uploaded. Update Click this button to upload the selected rmware le. See the Browse... button, above. Factory Reset Use these check boxes to select the type of factory-reset to perform. Placing a check mark in the des[...]

[...]

IP to RS-232 Converter 3 Appendix Default Settings ................................................................................................... 70 RS-232 ........................................................................................................ 70 Network .........................................................................[...]

page | 70 Default Settings Appendix Appendix The following table lists the default setting of the IP to 2 x RS-232 Converter , as displayed under the built-in Web interface. RS-232 RS-232 Settings Select RS-232 Port • 1 Description • None RS-232 Mode • TCP Bridge Baud Rate • 19200 Data Bits • 8 Parity • None Stop Bits • 1 Bridging Set[...]

page | 71 Appendix Network IP Settings MAC Address • Device-dependent (cannot be changed) Mode • Static IP Address • 192.168.1.72 Subnet • 255.255.255.0 Gateway • 192.168.1.254 HTTP Port • 80 TCP / T elnet Settings Enable TCP Access • Disabled Require Password on Connect • Disabled User Name • Admin (cannot be changed) Old Passwor[...]

page | 72 Appendix Connectors, Indicators, and Controls RS-232 • 2 x DB-9, male IP control • 1 x RJ-45 Power • 1 x 5V DC, locking Power indicator • 1 x LED, blue IP Reset button • 1 x T act-type, recessed Operational Power • 5V DC Power consumption • 1W (max.) Physical Dimensions (W x H x D) • 4.3” x 1” x 3.4” (1 10mm x 26mm x[...]

[...]

20600 Nordhoff St., Chatsworth CA 91311 1-800-545-6900 818-772-9100 fax: 818-772-9120 www.gefen.com support@gefen.com Stretch it. Switch it. Split it. Gefen’s got it. ® 20600 Nordhoff St., Chatsworth CA 91311 1-800-545-6900 818-772-9100 fax: 818-772-9120 www.gefen.com support@gefen.com *Pr eferred[...]