Português dropdown-ico

Giant 1-Feb manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26

Ir para a página of

Manuais similares

Bom manual de uso

As regras impõem ao revendedor a obrigação de fornecer ao comprador o manual com o produto Giant 1-Feb. A falta de manual ou informações incorretas fornecidas ao consumidor são a base de uma queixa por não conformidade do produto com o contrato. De acordo com a lei, pode anexar o manual em uma outra forma de que em papel, o que é frequentemente utilizado, anexando uma forma gráfica ou manual electrónicoGiant 1-Feb vídeos instrutivos para os usuários. A condição é uma forma legível e compreensível.

O que é a instrução?

A palavra vem do latim "Instructio" ou instruir. Portanto, no manual Giant 1-Feb você pode encontrar uma descrição das fases do processo. O objetivo do manual é instruir, facilitar o arranque, a utilização do equipamento ou a execução de determinadas tarefas. O manual é uma coleção de informações sobre o objeto / serviço, um guia.

Infelizmente, pequenos usuários tomam o tempo para ler o manual Giant 1-Feb, e um bom manual não só permite conhecer uma série de funcionalidades adicionais do dispositivo, mas evita a formação da maioria das falhas.

Então, o que deve conter o manual perfeito?

Primeiro, o manual Giant 1-Feb deve conte:
- dados técnicos do dispositivo Giant 1-Feb
- nome do fabricante e ano de fabricação do dispositivo Giant 1-Feb
- instruções de utilização, regulação e manutenção do dispositivo Giant 1-Feb
- sinais de segurança e certificados que comprovam a conformidade com as normas pertinentes

Por que você não ler manuais?

Normalmente, isso é devido à falta de tempo e à certeza quanto à funcionalidade específica do dispositivo adquirido. Infelizmente, a mesma ligação e o arranque Giant 1-Feb não são suficientes. O manual contém uma série de orientações sobre funcionalidades específicas, a segurança, os métodos de manutenção (mesmo sobre produtos que devem ser usados), possíveis defeitos Giant 1-Feb e formas de resolver problemas comuns durante o uso. No final, no manual podemos encontrar as coordenadas do serviço Giant na ausência da eficácia das soluções propostas. Atualmente, muito apreciados são manuais na forma de animações interessantes e vídeos de instrução que de uma forma melhor do que o o folheto falam ao usuário. Este tipo de manual é a chance que o usuário percorrer todo o vídeo instrutivo, sem ignorar especificações e descrições técnicas complicadas Giant 1-Feb, como para a versão papel.

Por que ler manuais?

Primeiro de tudo, contem a resposta sobre a construção, as possibilidades do dispositivo Giant 1-Feb, uso dos acessórios individuais e uma gama de informações para desfrutar plenamente todos os recursos e facilidades.

Após a compra bem sucedida de um equipamento / dispositivo, é bom ter um momento para se familiarizar com cada parte do manual Giant 1-Feb. Atualmente, são cuidadosamente preparados e traduzidos para sejam não só compreensíveis para os usuários, mas para cumprir a sua função básica de informação

Índice do manual

  • Página 1

    CHAPTER Installing and Starting Up the Hub 2-1 2 Installing and Star ting Up the Hub This chapter provides installation w arnings, guidelines, requirements, and package contents and the follo wing procedures: • Unpacking the hub • Po wering up the hub and running the power -on self-test (POST) • Installing the hub on a tabletop or shelf, in a[...]

  • Página 2

    Warnings FastHub 400 10/100 Series Installation and Configuration Guide 2-2 Warnings T ranslated v ersions of the follo wing safety warnings are provided in Appendix E, “T ranslated Safety W arnings. ” W arning Only trained and qualified personnel should be allo wed to install or replace this equipment. W arning Do not work on the system or co[...]

  • Página 3

    Installing and Starting Up the Hub 2-3 EMC Regulatory Statements W arning This equipment is intended to be grounded. Ensure that the host is connected to earth ground during normal use. W arning When installing the unit, the ground connection must always be made first and disconnected last. W arning Do not stack the chassis on an y other equipment[...]

  • Página 4

    Installation Guidelines and Requirements FastHub 400 10/100 Series Installation and Configuration Guide 2-4 Installation Guidelines and Requirements When determining where to place the hub, ensure the following conditions are met: • Cable distances from the hub to network equipment and workstations are within the limits described in Appendix B, ?[...]

  • Página 5

    Installing and Starting Up the Hub 2-5 Package Contents Pac kage Contents Each hub is shipped with the following items: • F astHub 400 10/100 Series Cabling and Start Up • This F astHub 400 10/100 Series Installation and Configuration Guide • Cisco Documentation CD-R OM • AC po wer cord • Mounting kit containing the following items: — [...]

  • Página 6

    Powering Up the Hub and Running POST FastHub 400 10/100 Series Installation and Configuration Guide 2-6 Powering Up the Hub and Running POST Before installing and cabling the hub, you might want po wer up the hub and verify that it is operational. T o power up the hub, connect one end of the AC po wer cord to the AC po wer connector on the hub and [...]

  • Página 7

    Installing and Starting Up the Hub 2-7 Installing the Hub on a Table or Shelf Installing the Hub on a T able or Shelf T o install the hub on a table or shelf, follow these steps: Step 1 Be sure the hub is po wered of f and is not connected to a power source. Step 2 Locate the adhesiv e strip with the rubber feet that shipped with the hub. Step 3 At[...]

  • Página 8

    Installing the Hub in a Rack FastHub 400 10/100 Series Installation and Configuration Guide 2-8 Installing the Hub in a Rac k This section describes how to install the hub in 19- and 24-inch standard and telco racks. Note Be sure the hub is po wered off and is not connected to a po wer source before you perform the steps in the sections that follow[...]

  • Página 9

    Installing and Starting Up the Hub 2-9 Attaching the Brackets to the Hub Figure 2-2 Attaching Brac kets for 19- and 24-inc h Racks (Rear P anel Forward) Figure 2-3 Attaching Brac kets for 19- and 24-inc h Racks (Mid-Mount) H10186 19" configuration Phillips flat-head screws O R REMOTE S UPPLY N MANUAL + 12V @ 1A H10187 24" configuration Ph[...]

  • Página 10

    Installing the Hub in a Rack FastHub 400 10/100 Series Installation and Configuration Guide 2-10 Attaching the Hub to the Rac k After the brackets are attached, use two of the Phillips machine scre ws to securely attach each bracket to the rack, as sho wn in Figure 2-4. Figure 2-4 Attaching the Hub to a Rac k (Front P anel Forward) H10559 RPS MODE [...]

  • Página 11

    Installing and Starting Up the Hub 2-11 Attaching the Cable Guide to the Bracket Attaching the Cab le Guide to the Brac ket Attaching the cable guide and securing the cables in the cable guide prev ent the cables from obscuring the hub and other de vices in the rack. If the hub is in a 19- or 24-inch rack, you can attach the cable guide to the left[...]

  • Página 12

    Installing the Hub on a Wall FastHub 400 10/100 Series Installation and Configuration Guide 2-12 Installing the Hub on a W all This section describes how to attach the hub in parallel and v ertically to a wall. Note Be sure the hub is po wered off and is not connected to a po wer source before you perform the steps in the sections that follow . Att[...]

  • Página 13

    Installing and Starting Up the Hub 2-13 Attaching the Hub to a Wall Attaching the Hub to a W all For the best support of the hub and cables, mak e sure the hub is securely attached to a wall stud or to a firmly attached plywood mounting backboard, as sho wn in Figure 2-7. Y ou must supply your own scre ws to attach the hub to the wall. Note If you[...]

  • Página 14

    Connecting to the Console Port (FastHub 400M Models) FastHub 400 10/100 Series Installation and Configuration Guide 2-14 Connecting to the Console P or t (F astHub 400M Models) T o connect the RJ-45 console port of a FastHub 400M model to a management station or modem, you must use the supplied RJ-45-to-RJ-45 rollov er console cable and the appropr[...]

  • Página 15

    Installing and Starting Up the Hub 2-15 Connecting to the Console Port (FastHub 400M Models) Step 2 Connect one end of the supplied rollov er console cable to the console port, as shown in Figure 2-8. Caution Do not connect an actual telephone line, an ISDN line, or an Ethernet cable to this console port. Damage to the hub can result. Make sure you[...]

  • Página 16

    Assigning IP Information to the Hub (FastHub 400M Models) FastHub 400 10/100 Series Installation and Configuration Guide 2-16 Assigning IP Inf ormation to the Hub (F astHub 400M Models) After you install the hub and connect it to a management station, you can assign IP information to the hub . IP information identifies the hub to the network and i[...]

  • Página 17

    Installing and Starting Up the Hub 2-17 Assigning IP Information to the Hub (FastHub 400M Models) Step 5 Enter the IP address of the default gate way (for e xample: 10.1.105.254): Enter IP default gateway: 10.1.105.254 Note If the management station from which the FastHub 400 series Hub Manager is used is not on the same IP subnet as the hub, you m[...]

  • Página 18

    Connecting to the 10/100 Network Ports and Uplink Port FastHub 400 10/100 Series Installation and Configuration Guide 2-18 Connecting to the 10/100 Netw ork P or ts and Uplink P or t Y ou can connect the 10/100 network ports and the uplink port to the ports on any 10BaseT or 100BaseTX network de vice, such as workstations, servers, switches, router[...]

  • Página 19

    Installing and Starting Up the Hub 2-19 Connecting to the 10/100 Network Ports and Uplink Port • Connecting to devices that do not autonegotiate or that ha ve their speed setting manually set can reduce performance or result in no link. T o maximize performance, choose one of these methods for configuring the 10/100 ports: — Let both ports aut[...]

  • Página 20

    Accessing the Management Interfaces (FastHub 400M Models) FastHub 400 10/100 Series Installation and Configuration Guide 2-20 Step 2 Connect the other end of the cable to the 10BaseT or 100BaseTX port of the network de vice. Step 3 Check to see that the port LED for the port that you connected in Step 1 comes on. If the port LED does not come on, c[...]

  • Página 21

    Installing and Starting Up the Hub 2-21 Accessing the FastHub 400 Series Hub Manager Accessing the F astHub 400 Ser ies Hub Manager T o access the hub manager, all you need is the IP information of the hub (and the password if one has been assigned). IP information for the hub is usually assigned when the hub is first started up after installation[...]

  • Página 22

    Accessing the Management Interfaces (FastHub 400M Models) FastHub 400 10/100 Series Installation and Configuration Guide 2-22 Figure 2-10 Home P age Note Y ou can bookmark the hub IP address to retrieve the hub manager for later use. If you are using Communicator , choose the Communicator menu option, and select Bookmarks > Add Bookmark . If you[...]

  • Página 23

    Installing and Starting Up the Hub 2-23 Accessing the CLI Accessing the CLI Y ou can access the CLI • From a console terminal connected to the hub console port. For more information, see the “Connecting to the Console Port (FastHub 400M Models)” section on page 2-14. • Through a T elnet session from a remote host by entering the telnet comm[...]

  • Página 24

    Accessing the Management Interfaces (FastHub 400M Models) FastHub 400 10/100 Series Installation and Configuration Guide 2-24 • CISCO-SIBU-MAN A GERS-MIB.my contains the MIB module for management interfaces on the FastHub 400M models. • CISCO-SIBU-ST A CKABLE-DU AL-SPEED-HUB-MIB.my contains the MIB module that extends the REPEA TER-MIB to manag[...]

  • Página 25

    Installing and Starting Up the Hub 2-25 Accessing the MIB Files through SNMP Using CCO to Access the MIB Files T o access the MIB files from CCO, click Software & Support to display the Software Center site. CCO serves a wide v ariety of users through two interfaces that are updated and enhanced simultaneously: a character-based v ersion and a[...]

  • Página 26

    Where to Go Next FastHub 400 10/100 Series Installation and Configuration Guide 2-26 Where to Go Next Now that you ha ve installed the hub and, if you hav e a FastHub 400M models, assigned IP information to the hub, you can continue to • Chapter 3, “Configuring and Monitoring from the Hub Manager” for configuration and monitoring informatio[...]