Grizzly H5571 manual

COPYRIGHT © SEPTEMBER, 2003 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. PRINTED IN TAIWAN ONLINE MANUAL DISCLAIMER THE INFORMATION IN THIS MANUAL REPRESENTS THE CONFIGURATION OF THE MACHINE AS IT IS CURRENTLY BEING SHIPPED. THE MACHIN[...]

For Your Own Safety Read Instruction Manual Before Operating This Equipment Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury. Indicates a potentially hazardous situation which, if not a[...]

H5571 34˚ Framing Nailer Kit -2 - 10. USE PROPER AIR HOSE for the tool. Make sure your air hose is in good condition and is long enough to reach your work without stretching. 11. WEAR PROPER APPAREL. DO NOT wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Non-slip footwear is recommend[...]

H5571 34˚ Framing Nailer Kit -3 - Operating this nailer can propel objects into the air, causing immedi- ate eye damage. To protect yourself, always wear American National Standards Institute (ANSI) approved safety glasses or goggles when oper- ating this equipment. In addition, this nailer discharges at 85-90 decibels. To protect your hearing, al[...]

H5571 34˚ Framing Nailer Kit -4 - INTRODUCTION Commentary Most important, we stand behind our tools. If you have any service questions or parts requests, please call or write us at the location listed below. Grizzly Industrial, Inc. 1203 Lycoming Mall Circle Muncy, PA 17756 Phone: (570) 546-9663 Fax: (800) 438-5901 E-Mail: techsupport@grizzly.com [...]

H5571 34˚ Framing Nailer Kit -5 - Compressed Air System Safety Yoke Mechanism Exceeding the maximum permissible operating pressure may cause the nailer to explode, blowing metal frag- ments in all directions. To protect yourself from serious personal injury, DO NOT allow your air compressor to exceed the recommended pressure when connected to this[...]

H5571 34˚ Framing Nailer Kit -6 - OPERATION Loading Nailer To load your nailer: 1. Disconnect the air supply from the nailer! 2. Pull the magazine pusher all the way back until it locks in place. 3. Place a stick of nails into the maga- zine as shown in Figure 2 . Make sure the pointed ends of the nails are fac- ing down. 3. Slide the stick of nai[...]

The nose of the gun houses a depth adjustment knob for setting the depth that the nailer drives nails into the workpiece. To adjust the depth: 1. If the nail is driven too far into the workpiece, rotate the knob clockwise as shown in Figure 4 ) 2. If the nail is not driven far enough into the workpiece, rotate the knob counter clockwise. H5571 34˚[...]

-8 - H5571 34˚ Framing Nailer Kit Clearing Jammed Nails The most frequent situation with any type of nailer is a nail jam. A jammed nail must be cleared before using the nailer again. The two places where a nail can get jammed are the magazine and the discharge area. To clear a jammed nail from the magazine: 1. Disconnect the nailer from the air s[...]

H5571 34˚ Framing Nailer Kit -9 - Cleaning Nailer Use a good solvent to clean the nose assembly of the nailer. Always be sure that the nailer is dry before using it again. Do not allow dust, chips, sand, etc. into the air connectors or into the body of the nail- er; this may result in leaks and damage to the nailer and the air fittings. Never use [...]

H5571 34˚ Framing Nailer Kit -10 - Replacing Pistons/O-Rings If you use your nailer day in and day out, Grizzly offers repair pistons as cheap insurance against wasted down time and lost profits in the event that a piston or pis- ton shaft becomes worn out. 5. The top of the piston should now be visible inside the cylinder, which is housed in the [...]

H5571 34˚ Framing Nailer Kit -11 - H5571 PART BREAKDOWN 25 95 68 84 65 85 67 88 30 28 27 59 26 39 40 38 37 7 92 91 56 24 30 35 29 83 28 82 31 35 66 35 62 97 96 63 64 73 82 74 80 89 90 36 32 34A 61 85 6 5 4 2 7 1 23 22 19 21 20 16A 21-1 100 50 49 48 47 45 46 44 42 43 41 53A 52 51 78 72 58 57 10 12-1 8 9 12-1 14 13 12 11 60 87 70 15-1 15-2[...]

H5571 34˚ Framing Nailer Kit -12 - 1 PSB115M BTN HD CAP SCR M6-1 X 16 2 PH5571002 EXHAUST COVER 4 PH5571004 RUBBER WASHER 10MM 5 PSB06M CAP SCREW M6-1 X 25 6 PH5571006 CAP 7 PW09M FLAT WASHER 7MM 8 PH5571008 SPACER 9 PH5571009 PISTON STOPPER 10 PH5571010 SPRING 11 PH5571011 O RING 12 PH5571012 PISTON HEAD VALVE 12-1 PH5571012-1 SPACER 13 PH5571013[...]

TROUBLESHOOTING Air leaking at trigger valve area. Air leaking between hous- ing and hose. Air leaking between hous- ing and cap assembly. Tool skips nails while dis- charging. Tool runs slowly or has a loss of power. Fasteners frequently jam the nailer. Nailer does not fire. 1. O-rings must be replaced & operation of safety yoke must be checke[...]

H5571 34˚ Framing Nailer Kit -14 - Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main- tenance. This is Grizzly’s sole[...]

Name __________________________________________________________ Street __________________________________________________________ City ____________________ State ________ Zip _________ Phone Number ____________ E-Mail ___________________ FAX ____________ Model # _______________Serial#________________ Order # ______________ The following information[...]

FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT NAIL Name________________________________ Street________________________________ City______________State______Zip_______ Send a Grizzly Catalog to a friend: Place Stamp Here[...]