Haier HC18-60A1VAR/S manual

No.0010572324 K 10 to 13 SEER 1.5 to 5 T ons Models: HC18-60A1V AR/S HC18-60C1V AR HC18-60D1V AR Installation & Operation Manual Central Air Conditioner The information contained in this booklet is subject to change without notice.[...]

! W ARNING These instructions are intended as an aid to qualified, licensed service personnel for proper installation, adjustment and operation of this unit. Read these instructions thoroughly before attempting installation or operation. Failure to follow these instructions may r esult in improper installation, adjustment, service or maintenance po[...]

1 T ABLE OF CONTENT 1.Introduction --------------------------------------------------------------------------------------- 2.Nomenclature for Model Number ------------------------------------------------------------- 3.Specification ------------------------------------------------------------------------------------- 4.Unit Inspection -------------[...]

2 3.SPECIFICA TION The dimensions for the condensing unit are illustrated in Figure 1 . Physical and electrical specifications are provided in T able 1 for 10 SEER systems respectively . Model:HC18-60A1V AR/S 40 35 45 50 60 18.3 15.8 21.3 24.4 26.9 28.9 130 90 130 140 149 165 1.43 1.43 1.43 1/3 1/3 1/3 1075 1075 1075 3/8" [9.52] 3/8"[9.52[...]

Figure 1 Minimum Circuit Amps 15 25 25 30 40 35 40 60 60 Rated Load Amps 7.4 9.6 1 1.8 13.0 16.7 15.8 18.7 26.6 28.9 Compressor Locked Running Amps 48 60 73 85 105 90 135 155 165 Full Load Amps 0.86 1.4 1.4 1.43 1.43 1.43 1.43 Fan Motor Rated HP 1/8 1/5 1/5 1/3 1/3 1/3 1/3 Nominal RPM 850 1075 1075 1075 1075 1075 1075 Liquid Line OD - In (mm) 3/8&q[...]

4 Outdoor Unit With This Indoor Air handler Model Number HC18C1V AR HB2400VC1M20 HC24C1V AR HB2400VC1M20 HC30C1V AR HB3600V A1M20 HC36C1V AR HB3600VC1M25 HC42C1V AR HB4800V A1M25 HC48C1V AR HB4800V A1M25 HC60C1V AR HB6000VC1M25 41800 2900 58000 12 Bristol T able 4:System Cooling Capacity Air Handler Cooling Capacity (Btu/h) SEER Rated Sensible T ot[...]

5 4.UNIT INSPECTION This product has been inspected at the factory and released to the transportation agency without known damage. Inspect exterior of carton for evidence of rough handling in shipment. Unpack carefully . If damage is found, report immediately to the transportation agency . 5.EQUIPMENT PROTECTION FROM ENVIRONMENT The metal parts of [...]

Provide a level concrete slab. T o prevent transmission of noise or vibration, slab should not be connected to building structure. Some sort of sound-absorbing material should be placed between the condenser and the slab. A good material to use is rubber and cork pad. For rooftop application, make sure the building construction can support the weig[...]

OUTDOOR UNIT LIQUID LINE PITCH SUCTION LINE TOW ARD OUTDOOR UNIT 1/2" FRO EVER Y 10' OF LINE INDOOR UNIT ABOVE OR LEVEL TO OUTDOOR UNIT INDOOR UNIT OUTDOOR UNIT ADDITIONAL SUCTION LINE OIL TRAP FOR EACH 20 FOOT RISE OF PIPE INDOOR UNIT LIQUID LINE SUCTION LINE OIL TRAP WHEN INDOOR UNIT IS 4 FEET OR MORE BELOW OUTDOOR UNIT INDOOR UNIT BELO[...]

The factory charge is suf ficient for 25 feet of standard liquid line. For longer or shorter liquid line lengths, adjust the charge as follows: 1/4" Line +/- 0.3 oz. Per foot 5/16" Line +/- 0.4 oz. Per foot 3/8" Line +/- 0.6 oz. Per foot 1/2" Line +/- 1.2 oz. Per foot V ertical Separation between Indoor and Outdoor Units Maximum[...]

9 1.T ubing should be cut square. Make sure it is round and free of burrs at the connecting ends. Clean the tubing to prevent contamination from entering the system. 2.Make sure that both refrigerant stop valves at the outdoor unit are closed. 3.Push the tubing into the fitting until it stops. This prevents flux from getting into the system. 4.Remo[...]

1.Fully open both shutoff valves. 2.Connect service gage manifold to the valve service ports, being sure to evacuate lines. 3.Startup the system (Refer to the Section 7 - "System Startup"). Run system at least 10 minutes to allo pressure to stabilize. 4.T emporarily install thermometer on suction (large) line near condensing unit. Be sure[...]

1 1 The condensing unit rating plate and the tables of "Physical and Electrical Specifications / Outdoor Units" (T able 1 and 2) provide pertinent data necessary for the selection of proper size electrical service and over-current protection devices. T able 9 provides data on the minimum copper wire size as a function of supply wire lengt[...]

12 8.OPERA TION Most single phase units are operated without start relay or start capacitor . Such systems should be off for a minimum of 5 minutes before restarting to allow equalization of pressures. The thermostat should not be moved to cycle unit without waiting 5 minutes. T o do so may cause the compressor to stop on an automatic open overload[...]

13 Run or start capacitor defective Replace Loose connection Check and tighten all connections. Condenser fan runs, Compressor stuck, grounded or open W ait for 2 hours for overload to reset. compressor doesn't motor winding, open internal overload Replace compressor if still open. Low voltage condition At compressor terminals, voltage must be[...]

5 PU EL E C T RIC HE A TER KIT RD BL Air Conditioner Wi ri ng Diagram 1) Confi r m sy stem selec t ion. Opti onal com ponents m ay be f iel d or f act or y i ns t all ed . 2) If LP S an d /o r H PS n o t in s t all e d o r r em o v ed , a ju m p er w i r e m us t b e p r es en t acr oss circu i t f o r syst em t o o p er at e. 3) For pr o per syste[...]

Made in P .R.C.[...]