Harbor Freight Tools 44846 manual

34 INCH FLOOR RADIAL DRILL PRESS Model 44846 ASSEMBL Y AND OPERA TING INSTR UCTIONS Visit our website at: http://www .harborfreight.com Read this material bef ore using this pr oduct. F ailure to do so can result in serious injury . SA VE THIS MANU AL. Cop yright © 2000 b y Harbor F reight T ools ® . All rights reser ved. No por tion of this manu[...]

P age 2 SKU 44846 Specifications Save This Manual Y ou will need the manual f or the safety w ar nings and precautions, assemb ly instructions, operating and maintenance procedures , par ts list and diagram. K eep y our in voice with this manual. Write the in voice n umber on the inside of the front cov er . K eep the manual and inv oice in a safe[...]

P age 3 SKU 44846 5. Do not for ce tool . It will do the job better and more safely at the rate f or which it was intended. Do not use inappropr iate attachments in an attempt to e xceed the tool capacity . 6. Use the right tool for the job . Do not attempt to force a small tool or attachment to do the work of a larger industrial tool. There are ce[...]

P age 4 SKU 44846 replacement par ts. Use of any other par ts will v oid the warr anty . Only use accessor ies intended f or use with this tool. Approv ed accessories are av ailab le from Harbor F reight T ools. 19. Do not operate tool if under the influence of alcohol or drugs . Read warning labels on prescriptions to deter mine if your judgment [...]

P age 5 SKU 44846 8. When finished with the Drill Press, alwa ys press the Switch to the OFF position. 9. Do not mount (or adjust) the workpiece on the Drill Press T able while the motor is running. 10. When drilling or cutting large holes, use the slow er speeds and securely f asten the workpiece to the table using a mounted vise . 11. Do not use[...]

P age 6 SKU 44846 5. Install the T able Support (B7), with attached table Ar m (B14), o ver the Column (B1) and slide it down. Engage the gears onto the Rack (B2). Tighten the T able Clamp (B13). 6. Slide the Column Collar (B19) ov er and do wn the Column (B1) about 8 inches. Tighten Screw (B11). 7. Place the Extend Ar m (B15) into the Arm (B14), a[...]

P age 7 SKU 44846 a wrench. - Rotate the T able until it is square to the bit. - Retighten the He x Bolt (B12). Operation W arning: A v oid personal injuries. Before operating this machine, revie w all Safety W arn - ings and Precautions listed on pages 2 through 5. Drilling While f ollowing these procedures , ref er to the photo on page 5. 1. Loos[...]

P age 8 SKU 44846 5. T o retur n the Head to the 90 degree position, do these procedures in re v erse. Moving the Head Horizontall y 1. Loosen the left-side Clamping Le v er (30) and rotate the Head Assembly up to 360 degrees . 2. Retighten the Clamping Le v er . Moving the Head Forwar d or Bac kward. 1. Loosen the right-side Clamping Lev er (30). [...]

P age 9 SKU 44846 4. Push the Motor (22) backw ard and hold. Retighten the Thumb Nut. Note : T o test the proper belt tension, push in on the center of each belt at its center . It should mov e only 1/2 inch (in or out). 5. Close the Belt Guard Lid. Maintenance W arning: Before perf orming an y maintenance to this machine, remo ve the line cor d fr[...]

P age 10 SKU 44846 3. With the screwdriv er still in place, loosen the (inner) He x Nut (7) until the Cap Spr ing notch disengages from the Spring Retainer (10) -- about 1/8 inch. 4. T ur n the screwdriv er counterclockwise and engage the ne xt Cap Spring notch. Leav e the screwdriver in place . 5. Tighten the (inner) He x Nut just enough to engage[...]

P age 11 SKU 44846 T roubleshooting SY MPT OM POSSI B LE C A USE S O L UT I O N Drill bi t b ur ns or smok es - I ncorrec t spi ndle speed - Du ll drill bit - Drillin g t oo slo wly - Lac king lubri cati on - Change spindle speed - Replace wit h new bit - D ri l l f a s t e r - Lubricate cutting area Mak e s un u sual noise - Belt tensi on set wron[...]

P age 12 SKU 44846 Item # Descript ion 1 S elf -tapping Scr e w , 4.2 2 No-V olt Sw itch 3 S crew , P an Hd., M 5x12 4 Switch Bo x 5 Scre w S et, Sp eci al 6 Nut, He x 7 Nut , He x, M 12 8 Cap Spring 9 S pr i ng , T or s i o n 10 R etai ner Spring 11 Seat Spring 12 Roll P in 13 Scre w , Sock et Hd. 14 Head 15 Loc king Shoe 16 Guide Pin 17 Ret ainin[...]

P age 13 SKU 44846 Pulley and Spindle Assemb ly P ar ts List Item # Descript ion A1 V -bel t, M58 A2 Pull ey Nut A3 Spindle Pul le y A4 Inser t Pul le y A5 Ret ai ning Ring A6 Loc ki ng Ring A7 W asher A8 Ball Bearing, 60203 A9 W ash er , Rub ber A10 Q uil l T ube A11 Chuc k Ke y A12 Chuc k A13 A rbor Item # Descript ion A14 Drift Ke y A15 Sp i ndl[...]

P age 14 SKU 44846 Base and T able Assembl y P ar ts List Item # Descrip t ion B1 Col umn B2 R a ck B3 Scre w , M10x12 B4 Col umn Sup por t B5 H ex Bolt , M10x40 B6 Base B7 T ab l e Sup por t B8 Cr a n k B10 Pin Gear B11 Scre w , M6x1 0 B12 H ex Bolt , M16x35 B13 T ab le Clamp B14 Arm B15 Exte nd Ar m B16 Su ppor t Clamp B17 Gear , H elical B18 W o[...]

P age 15 SKU 44846 LIMITED 1 YEAR / 90 D A Y W ARRANTY Harbor F reight T ools Co . makes ev er y effor t to assure that its products meet high qual- ity and durability standards , and warr ants to the original purchaser that f or a period of ninety da ys from date of purchase that the engine/motor , the belts (if so equipped), and the b lades (if s[...]