Hoover S3083-030 manual

HOOVER Model Owner’s i Celebrity II TM .S3083-030 Manual j Cleaner &L[...]

Fill in and retain ! The vacuum cleaner you have just purchased is a combination cleaner. It has a motorized power nozzle for carpet and floor cleaning and has cleaning tools for above the floor cleaning. Your cleaner is a model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..*.......................... a[...]

Importantsafeguards! l Read all instructions. l Warning: Electric shock could occur if used outdoors or on wet surfaces. l Close supervision is necessary when any appliance is used by or near children. Do not allow vacuum cleaner to be used as a toy or to run unattended at any time. l Keep hands, feet, loose clothing, and hair away from rotating ag[...]

14 A I 1. FURNITURE GUARD 2. COMBINATION CARPET AND FLOOR ‘POWERMATIC’ NOZZLE Powermatic nozzle automatically adjusts to different carpet pile height. Has setting for “Carpet” and “Bare Floor”. 3. SURFACE SELECTOR INDICATOR Shows “Carpet” or “Bare Floor” setting of Surface Selector Lever. 4. SURFACE SELECTOR LEVER Push lever wit[...]

6. WALL/FLOOR BRUSH 7. HOSE CORD CONNECTION TO CLEANER Plug hose cord into cleaner base to receptacle. 8. CASTERS Provide easier towing; pull cleaner using hose to guide the cleaner easily over carpet, throw rugs, and door sills. 9. ON-OFF SWITCH A convenient switch is located near front of cleaner. 10. CORD STORAGE HOOKS II. EXTENSION WANDS Connec[...]

TO CONNECT AND REMOVE HOSE To connect hose, insert hose into opening of cleaner lining up the arrow on the hose with the dot on the cleaner. Turn the hose clockwise until it lines up with the bar on the cleaner and latch locks into place. When the hose is attached properly, the hose cord plug will reach to the receptacle on the cleaner. Insert the [...]

HOW TO USE HANDLE ADJUSTMENTS The handle has two positions when used with the power nozzle: Storage and Low. Step on the Han- dle Adjustment Latch to lower the handle. Use the low position for reaching under low furniture. Raise the handle straight up for the storage position. CARPET AND RUG CLEANING When using the power nozzle for carpet and rug c[...]

FOR HARD SURFACE FLOOR CLEANING The power nozzle can be used for cleaning hard sur- face floors such as wood, linoleum, vinyl, asphalt and rubber tile, sealed cork, concrete and terrazzo as well as carpet. You will find it particularly con- venient when cleaning rugs to adjust the power noz- zle to “Bare Floor” and continue cleaning the sur- ro[...]

HOW TO USE THE ‘CELEBRITY II’ CLEANER WITH CLEANING TOOLS CLEANING TOOLS The cleaning tools have many uses. Select the tool best suited for the cleaning task from the descrip- tions below. Adjust the Suction Regulator to select the amount of suction appropriate to the cleaning task. FURNITURE NOZZLE For upholstered furniture, draperies, tapestr[...]

TO CLEAN HARD TO REACH AREAS Use the curved wand with the extension wands. The tools attached to the curved wand will enable you to clean many hard to reach areas; especially crown moldings, tops of drapery rods, shelves, and picture frames, etc. TO CLEAN STAIRS Clean stairs by placing the cleaner on its side as pictured in the illustration. Clean [...]

When To Replace Check bag from time to time. When the bag is filled with dirt, the cleaner will not operate effectively. Discard used bag. CAUTION: Very fine materials, such as face powder, cornstarch, fire- place ashes or fireplace soot, may seal the throw away bag and may cause it to burst even though it is only partially full of dirt. When the c[...]

HOW TO CLEAN SECONDARY FILTER DISCONNECT CLEANER FROM ELECTRICAL OUTLET BEFORE REMOVING FILTER The secondary filter is a foam disc located on top of the motor and protects the motor from dirt par- ticles. When the filter becomes dirty, either clean or replace it. To remove, pull filter from top of motor. Clean by rinsing it in water. When dry, slid[...]

To provide space for grasping the agitator, remove end of hose from holder, Fig. 3. Then grip agitator and pull out. Fig. 4. Remove old belt. Place one end of the new belt around agitator pulley with smooth side of belt against the pulley. Fig. 5. 5 Line up metal projection on end of agitator (opposite the belt) with groove on inside wall of nozzle[...]

Place a screwdriver under the belt as illus- trated. Fig. 8. 8 Bracing the end of the screwdriver against the end of the motor shaft, slide belt over end of shaft. Fig. 9. Remove screwdriver. Check to be sure belt is not twisted. 9 Rotate the agitator by hand to properly align the belt on the motor shaft. Agitator should rotate freely. Fig. 10. IO [...]

NOZZLE HOSE The Nozzle Hose carries the dirt from the nozzle to the extension wand and to the throw away bag. If the hose becomes obstructed, cleaning effectiveness will sharply decrease. Remove bottom plate as de- scribed in preceding section, and slide end of hose out of the holder. Clear hose and reinsert into holder. Replace bottom plate as des[...]

LOCATOR Remove brushes by pulling them from agitator with pliers. Slide new brushes into the channels - small ends first - pushing them in as far as possible. (Fig. 4). Replace end plate and shaft, lining up locator on end section with slot in agitator. Replace other end section and end plate and tighten. (Fig. 5). 5 END SECTION WAS BEARIN Should y[...]

HOW TO REPLACE THE BOTTOM PLATE BRUSH Disconnect cleaner from electrical outlet and disconnect Powermatic nozzle from extension wand. 1 Put the Surface Selector Lever in the “Carpet” Position. This will allow for easier removal of the brush. Turn Power- matic nozzle over. Remove bottom plate by unscrewing the 2 Phillips head screws at the back [...]

USER CHECK LIST This appliance was inspected thoroughly and was in good operating condition when it was shipped from the factory. If a minor problem develops, it usually can be remedied quite easily when the cause is identified. Accordingly, this check list is provided for your convenience. PROBLEM POSSIBLE CAUSE POSSIBLE SOLUTION A. CLEANER 1. Not[...]

LUBRICATION The motor is equipped with one ball bearing and one roller bearing. These bearings contain sufficient lubrication for the life of the motor. The addition of lubricant could cause damage. Therefore, do not add lubricant to either motor bearing. The agitator is equipped with two ball bearings that should be lubricated periodically. This s[...]

VCMA VACUUM CLEANER MANUFACTURERS ASSOCIATION (HOOVER - AN ASSOCIATION MEMBER) Service To The Consumer Since 19 13 This information has been compiled by the Vacuum Cleaner Manufacturers Associ- ation from Governmental and Private Sources concerned with product safety. These basic guidelines are for your protection and convenience. TO AVOID ELECTRIC[...]