Hunter Fan MB519-01 manual

MB519-01 • 03/13/15 • © Hunter F an Company www .HunterF anInternational.com ENGLISH[...]

Befor e installation and usage of this produc t, please read this manual and keep it for future ref erence .[...]

www .HunterF anInternational.com PA G E 12 PA G E 5 30 inches 7 feet PA G E 2 What to Expect with Y our Installation Ceiling Br acket Ladder PA G E 3 T ools Needed Maintenanc e & Cleaning T roubleshooting Swit ch Housing Light Kit T able of C ontents PA G E 6 PA G E 9 Wiring C anopy Downrod PA G E 10 Blades PA G E 4 Mounting Options PA G E 13 P[...]

www .HunterF anInternational.com MB519-01 • 03/13/15 • © Hunter F an Company What t o Expec t with Y our Installation 2 Know your wiring If you are unfamiliar with wiring , use a qualied electrician. Y ou may need a friend to help you . Check box to see fan weight Assess ceiling angle Ceiling angles greater than 34° will require an Angled [...]

www .HunterF anInternational.com T ools Needed Ladder Po wer Drill (optional) 9/64” Drill Bit (optional) Screwdrivers Pliers Wire Strippers If mounting to a support structure, you will also need these tools . 3 MB519-01 • 03/13/15 • © Hunter F an Company[...]

www .HunterF anInternational.com If you ha ve an angled ceiling: 1. Y ou will need a longer downrod (sold separately) . 2. If your ceiling angle is greater than 34°, y ou will also need an Angled Mounting Kit (sold separately) . Guide T ouches BOTH Ceiling & Wall S I T U A T I O N 1 Guide T ouches W all but NOT Ceiling S I T U A T I O N 2 Y ou[...]

www .HunterF anInternational.com C eiling Bracket Refer to warning w .1 on pg. 2 T o avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location. F or angled ceilings, point opening toward peak. Make sure all four bumpers are still a[...]

6 Downrod Slid e Slid e 1 2 3 4 5 6 7 8 9 10 Sold Separately Included Longer Downrod for angled ceilings or ceilings 3 m (10’) or higher Shorter Downrod for fans installed close to ceiling Standard Downrod for ceilings 2,4-3 m (8-10’) high Option 1 Option 2 Option 3 skip to next page If you need a diff erent downrod length follo w these steps: [...]

7 KEEP! 20 cm (8”) 1 cm (3/8”) C U T & S T R I P (not to scale) Remove the pr e-installed setscrew so that the downrod can be inserted. Hand tighten the downrod (at least 4-5 full turns) until it stops. The wires can be cut, but leave at least 8” extending from the top of the downr od. Downrod (c ontinued) 20 cm (8”) 1 cm (3/8”) Tight[...]

www .HunterF anInternational.com Downrod (c ontinued) DO NO T PICK THE F AN UP BY THE CANOPY OR WIRES. Place the downrod ball int o the slot in the ceiling bracket. Put the wires and do wnrod through the canopy . Let the canopy sit loosely on t op of the fan. 8 MB519-01 • 03/13/15 • © Hunter F an Company[...]

www .HunterF anInternational.com Wiring F R O M F A N F R O M C E I L I N G B R A C K E T F R O M F A N Using an orange wire connector from the hardware bag , connect the 3 grounding wires (green, green/yello w stripe, or bare c opper) coming from the ceiling , downrod , and hanging bracket. (Grounding) Green/Y ellow Stripe Green/Y ellow Stripe Whi[...]

www .HunterF anInternational.com Canop y Lift the canopy into place so that the screw holes are aligned . Position the canop y so that, when lifted into place , the canopy ts int o the hanging bracket as shown. Screw Holes Insert the two canopy screws found in the hardware bag . 10 MB519-01 • 03/13/15 • © Hunter F an Company[...]

www .HunterF anInternational.com Blades 11 Put the blade washers , found in the hardware bag , onto the blade screws, f ound in the hardware bag. T hen install the blade screws to secure each blade to a blade ir on. 11 Lightly attach the blade irons to the motor with screws found in the hardware bag , then securely tighten after both screws are att[...]

www .HunterF anInternational.com Make sure the upper switch housing is securely attached to the mounting plate. F ailure to properly secure all 3 assembly screws could result in the switch housing xture falling. S witch Housing F eed the wire plug through the center hole of the upper switch housing , then lift the keyhole slots around the screws[...]

13 Light Kit Partially install two of the light kit assembly screws, f ound in the hardware bag, into the upper switch housing . Lif t the light kit assembly and connect the plugs from the upper and lower switch housings . Mak e sure to line up the colored markings on the connectors. Align the keyhole slots in the light k it assembly with the two s[...]

14 Install a CFL bulb into each of the sockets. When necessary , replace with bulbs of the same type and wattage. Lift the inner glass ush against the metal plate and install the globe keeper . Thread the pull chains through the holes in the nial cap . Screw the nial onto the threaded rod . Raise the outer glass to the light kit and align [...]

www .HunterF anInternational.com Light Kit (c ontinued) C ONGRA TULA TIONS! Y OU’RE DONE! See next page for fan opera tion instruc tions. T o attach the outer glass, install the thumbscrews and tighten securely . Connect the appropriate pull chain pendant to each of the short chains. The fan pull chain controls the speed: from high to off . The l[...]

www .HunterF anInternational.com Maintenanc e & Cleaning ON T urn Po wer Changing the direction of air ow - unscrew the nial and remov e it from the threaded rod . Remove the nial cap and unscrew the globe keeper while supporting the inner glass with your other hand . Carefully remov e the inner glass. Move the re vers e switch to the [...]

www .HunterF anInternational.com T roubleshooting Exc essive w obbling • Tighten all of the blade and blade iron screws until they are snug . • T urn the power off , suppor t the fan carefully , and check that the hanger ball is properly seated . • Use the provided balancing kit and instruc tions to balance the fan. Noisy Operation • Tighte[...]