Husqvarna 966004701 manual

Operator's Manual 200 9 -0 2 115145227 Blower Kit - 52" Collection System Operator's Manual 966004701[...]

CONTENTS CONGRA TULA TIONS on the purchase of a new collection system. It has been designed, engineered and manufactured to give you the best possible dependability and performance. Should you experience any problem you cannot easily remedy , please contact your nearest authorized service center/ department. They have competent, well-trained techni[...]

4 SAFETY RULES SAFE OPERA TION PRACTICES FOR RIDE-ON MOWERS DANGER ! THIS CUTTING MACHINE IS CAP ABLE OF AMPUT A TING HANDS AND FEET AND THROWING OBJECTS. F AILURE TO OBSER VE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESUL T IN SERIOUS INJURY OR DEA TH. GENERAL OPERA TION • Read, understand and follow all instructions in the manual and on the m[...]

5 SAFETY RULES SAFE OPERA TION PRACTICES FOR RIDE-ON MOWERS DO NOT • Donot turn on slopes unless necessary , and then, turn slowly and gradually downhill, if possible. • Donot mow near drop-off, ditches, or embankments.Themowercouldsuddenlyturn over if a wheel is over the edge of a cliff or ditch, or if an edge [...]

6 SAFETY RULES SAFE OPERA TION PRACTICES FOR RIDE-ON MOWERS • Keep machine free of grass, leaves, or other debris buildup. Clean oil or fuel spillage. Allow machine to cool before storing. • Stopandinspecttheequipmentifyoustrikean object. Repair , if necessary , before restarting. • Nevermakeadjustmen[...]

7 UNP ACKING INSTRUCTIONS • Removeallpartsandpackingmaterialsfrom carton. TOOLS REQUIRED • 7 / 16 "Wrenchorratchetandsocket • ½"Wrenchorratchetandsocket • 7 / 8 "Socket • T orque Wrench • Phillips Head Screwdriver • Hacksaw • Pliers NOTE: W[...]

8 1. Removethedischargechutefromthedeck.(Deck congurationwillvarybysizeandmodel) 2. Lowerdecktothelowestcuttingposition. 3. Removetherighthand(dischargeside)beltcover fromthedeck. 4. Relievethetensionfromthedeckbeltandrem[...]

9 3 MOUNTING BLOWER ASSEMBL Y Outer Pulley Cover Pin Hairpin Cotter RearMountBracket Contact Area 1. Position blower over the discharge tabs on the deckandsetblowerontothedeck. 2. Besuretheblowerissittingushagainstthe outsideofthedeck. 3. Installthefrontmountbracket[...]

10 Install the bagger mount tube to the rear guard 1. with 5 / 16 -18x3¼boltsandangenutsfromkit. NOTE: Depending on model, rear guard hole may need to be drilled out to 5 / 16 "ifkithardwareistoo large. Installkitsupportstrapsontheoutsideofthe 2. mount tube as shown in th[...]

11 1. Position upper chute support against bagger inlet, ushatouteredges.SeeIllustration. 2. Using support as a template, drill two 3 / 8 holes into bagger hood. Upper Chute Support Bagger Inlet Nut Bagger Hood Flat W ashers Hex Bolt Flex T rim 3. Secure upper chute support to hood with hex bolts, washers and nyloc nuts. ASSEMBL Y[...]

12 TIPS FOR IMPROVED BAGGING Follow the mower operation instructions in you mower operator ’s manual. When operating your grass catcher on a lawn where grass and leaf bagging equipment has not been used,youarepickingupthatchanddebristhathas accumulated for long periods of time. The amount collected and the total time[...]

13 OPERA TION CAUTION • DONOToperatemowerwith grass catcher partially installed. • Disengagebladesandstop engine before leaving mower seat to empty containers, unclogging chutes, etc. • Closecoverbeforestarting. • Disengagemowerbladeswhen crossing driveways or gravel surfaces and o[...]

14 4 5 7 8 9 10 11 13 14 T orque to 30 ft/lbs 15 16 17 18 19 20 21 22 23 39 26 25 29 30 38 28 24 1 2 3 6 10 12 14 15 23 33 34 35 36 31 44 32 37 44 43 11 40 47 48 50 51 52 48 51 42 45 46 27 49 48 41 45 40 47 44 55 11 59 56 11 40 56 11 60 12 REP AIR P AR TS 57 54 53 61[...]

15 539 101977 1.. .... 1 .... TRACTION SPRING 539 976952 2.. .... 1 .... SCREW 10-24 x .625 RD 539 10441 1 3.. .... 1 .... KNOB W/STUD 539 104763 4.. .... 1 .... RET AINER U TYPE 539 105785 5.. .... 1 .... DECAL, W ARNING 539 106741 6.. .... 1 .... DECAL, SEVERING 539 108084 7.. .... 1 .... W ASHER, 3 / 16 x ¾ x 16 GA 539 108088 8.. .... 1 .... LA[...]

16 6 5 4 4 3 3 1 9 2 12 10 7 8 11 REP AIR P AR TS[...]

17 539 108081 1.. .... 1 .... SCREW , SPEC 10-14 x ½ 539 108082 2.. .... 1 .... INDICA TOR, BAG DUMP 539 108083 3.. .... 2 .... SCREW 10-24 x 1 1 / 8 539 108084 4.. .... 3 .... W ASHER 3 / 16 x ¾ 539 108085 5.. .... 2 .... SP ACER, SPLIT 539 108086 6.. .... 2 .... NUT , ACORN 10-24 ITEM P ART NO. QTY . DESCRIPTION ITEM P ART NO. QTY . DESCRIPTION[...]

18 REP AIR P AR TS 1 2 3 4 5 7 8 9 10 11 12 13 14 15 16 17 18 19 20 6 18 9 18 18[...]

19 ITEM P ART NO. QTY . DESCRIPTION ITEM P ART NO. QTY . DESCRIPTION REP AIR P AR TS 539 130307 1.. .... 1 .... SHIELD, BEL T 539 130320 2.. .... 1 .... PULLEY 539 105743 3.. .... 1 .... DECAL, NO STEP 539 130347 4.. .... 1 .... BEL T 539 100472 5.. .... 2 .... RHSNB 5 / 16 -18 x 1¼ 539 990717 6.. .... 2 .... NUT 5 / 16 -18 HEX NYLOC 539 131091 7.[...]

SECTION 1: LIMITED WARRANTY Husqvarna Professional Products, Inc (“Husqvarna”) warrants the original purchaser the Husqvarna branded product to which this warranty apply (the “Product”) that the Product shall be free from defects in material and workmanship from the date of purchase for the period of the applicable “Warranty Schedule” o[...]

† Refer to Section 3 for items not covered by this warranty *All consumer product use must have been limited to the owner s residence. Warranted for noncommercial, nonprofessional, noninstitutional and nonincome producing use. **HUV 2 Year or 2,000 Hour Powertrain (The engine assembly, unitized transaxle assembly (gasoline vehicle), motor, and ma[...]

P/N 1 15 145227 IR 02/05/09[...]