Impex BF-1201 manual

NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Pack Assembly Instruction Parts List Warranty Ordering Parts Model BF-1201 Retain This Manual for Reference 100714 OWNER'S MANUAL MARCY ® Deluxe Elliptical Machine BF-1201 IMPEX ® INC. 2801 S. Towne Ave., Pomona, CA 91766 Tel: (800[...]

TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................…. 1 IMPORTANT SAFETY NOTICES ..................................................................…. 2 HARDWARE PACK ……….....…....................................................................…. 4 ASSEMBLY INSTRUCT IONS[...]

IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipm ent. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the ma[...]

WARNING LABELS PLACEMENT The Warning Labels shown here have been placed on the Rear Stabilizer, Front Post, and Main Frame. If the labels are missing or illegible, please call customer service at 1-800-999-8899 for replacement. Apply the labels in location shown. 3[...]

HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.[...]

4 ASSEMBLY INSTRUCTION Tools Required For Assembling the Machine: One Crossing Wrench and Allen Wrench, provided by manufacturer. NOTE: It is strongly recommended that two or more people assemble this machine to avoid possible injury. STEP 1 (See Diagram1) A.) Do not tighten the Nuts and Bolts until instructed to do so. B.) Attach the Front Stabili[...]

5 STEP 2 (See Diagram 2) A.) Note: Extra help may be needed to hold the Fr ont Post (#42) while connecting the computer wires. B.) Connect the Upper Computer Wire (#91) from t he bottom of Front Post to the Lower Computer Wire (#92) from the main Fame (#32). C.) Attach the Front Post to Main Frame. Secure them together with four M8 x ¾” Allen Bo[...]

6[...]

STEP 3 (See Diagram 3) A.) Note: In order to install the Pedal Supports (#30 & #38), extra help may be needed. B.) Do not tighten Nuts and Bolts until instructed to do so. C.) Attach the Left Pedal Support (#38) onto the groove on left Roller Wheel (#49). D.) Insert the pivot on Left Pedal Support into the hole on the left Connecting Bracket (#[...]

STEP 4 (See Diagram 4) A.) Cover the heads of the two M8 x ¾” Hex Bolts (#6) pre-installed by factory with two M8 Nut Caps (#5). B.) Cover the two M8 Aircraft Nuts (#23) insta lled in Step-3 with two M8 Nut Caps (#5). DIAGRAM 4 8[...]

STEP 5 (See Diagram 5) A.) Attach the two Pedals (#29) onto the Left & Right Pedal Support (#38 & #30). Secure each Pedal with three M8 x 1” Allen Bolts (#28). DIAGRAM 5 9[...]

STEP 6 (see Diagram 6) A.) Insert the Right Stride Handle (#2) into the Right Connecting Rod (#15). Insert the Left Stride Handle (#44) into the Right Connecting Rod (#41). B.) Securely tighten each Handle with two M8 x 2” Carriage Bolts (#11), two Ø 5/8” Curved Washers (#24), two Ø 5/8” Lock Washers (#7), and two M8 Acorn Nuts (#37). DIAGR[...]

STEP 7 (See Diagram 7) A.) Attach the Water Bottle Rack (#18) to the Fr ont Post (#42). Secure it with two M5 x 5/8” Philips Screws (#17). B.) Store the Water Bottle (#14) in the Rack. DIAGRAM 7 11[...]

STEP 8 (See Diagram 8) A.) Attach the Stationary Handle (#27) to Front Po st (#42). Secure it with four M8 x ¾” Allen Bolts (#21), four Ø 5/8” Lock Washers ( #7), and four Ø 5/8” Flat Washers (#22). DIAGRAM 8 12[...]

STEP 9 (See Diagram 9) A.) Remove the four M5 x 5/8” Computer Ph ilips Screws (#43) from the Computer (#45). B.) Connect the Upper Computer Wire (#91) to the wire on Computer. C.) Plug the sensor wire (#93) on the Fr ont Post (#42) into the Computer. D.) Attach the Computer to the bracket on Front Post. Secure it with the four (removed previously[...]

STEP 10 (See Diagram 10) A.) Plug the AC Adapter (#34) to110v outlet, and plug the power cord into the Main Frame (#32). Note: Only use the original AC Adapter from manufacturer. Do not use any Adapter, which is not from manufacturer. DIAGRAM 10 14[...]

EXPLDOED DIAGRAM 15[...]

16[...]

PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Stride Handle Cover Cap 2 51 Ø 1 1/8” x Ø 7/8” Spacer 2 2 Right Stride Handle 1 52 Ø 1 1/8” x ½” Bushing 2 3 Ø 1 ½” Stride Handle Bushing 2 53 Ø 1 1/8” x ¼” Spacer 2 4 Stationary Handle Grip 2 54 Connecting Bracket 2 5 M8 Nut Cap 4 55 Ø 1 1/8” x 5/8” Bushing 2 6 M8 x ¾” Hex Bolt [...]

OPERATION POWER Plug the AC Adapter to power outlet before exer cise. Un-plug AC Adapter when exercises are finished. SELECT EXERCISE PROGRAM Turn on Computer and select the desired exerci se program. Please refer to the Computer Manual for exercise program selection. FOOT POSITIONING Step both feet on the two Pedals and hold t he Stride Handles wi[...]

IMPEX ® INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX ® ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is l[...]

19[...]