Impex SM-4008 manual

NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Pack Assembly Instruction Parts List Warranty Ordering Parts Model SM-4008 Retain This Manual for Reference 100806 OWNER'S MANUAL MARCY ® SMITH MACHINE SM-4008 IMPEX ® INC. 2801 S. Towne Ave., Pomona, CA 91766 Tel: (800) 999-8899 F[...]

TABLE OF CONTENTS BEFORE YOU BE GIN..................................................................……………. 1 IMPORTANT SAFETY NOTI CES.................................................................… 2 SMITH MACHINE HARDWARE PACK….......…............................................. 4 SMITH MACHINE ASSEMBLY INSTRUCTIONS ..........[...]

IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In par ticular, note the following safety precautions: 1. Keep children and pets away from the ma[...]

The warning labels shown here have been placed on th e Rear Base, and Bench Rear Stabilizer. If the labels are missing or illegible, please call custom er service at 1-800-888-8899 for replacements. Apply the labels in the location shown. 3 SMITH MACHINE HARDWARE PACK[...]

NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 4[...]

SMITH MACHINE HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 5[...]

SMITH MACHINE HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 6[...]

SMITH MACHINE HARDWARE PACK 7[...]

SMITH MACHINE ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended that two or more people assemble this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Do not tighten Nuts and Bolts until instructed to do so. B.) Insert a Base Frame (#5) into the Rear [...]

STEP 2 (See Diagram 2) A.) Do not tighten the Nuts and Bolts until instructed to do so. B.) Insert a Guide Rod (#24) into the hole on le ft Base Frame (#5). Secure it with one M8 x 2 3/8” Allen Bolt (#103), two Ø 5/8” Washer s (#106), and one M8 Aircraft Nut (#109). Slide the Left Lower Safety Stop Frame (#26) onto the Guide Rod, and then slid[...]

10 STEP 3 (See Diagram 3)[...]

A.) Do not tighten all Nuts and Bolts until instructed to so. B.) Attach the Middle Vertical Frame (#9) under the Rear Top Beam (#6) and onto the Rear Base Frame (#8). C.) Attach the Lower Pulley Frame (#16) to the Middle Vertical Frame from rear. Attach the Foot Plate (#32) to the Middle Vertical Fram e from front. Secure them together with two M1[...]

12 STEP 4 (See Diagram 4) A.) Attach the Butterfly Base (#11) to the fr ont of Middle Vertical Frame (#9). Attach the Butterfly Pulley Bracket (#14) to the Middle Ve rtical Frame. Secure them together with two[...]

M10 x 2 ½” Carriage Bolts (#88), two Ø ¾” Washers (#107), and two M10 Aircraft Nuts (#110). B.) Attach the Butterfly Stopper (#31) to Butterfly Base. Secure it with two M6 x 3/8” Allen Bolts (#58). C.) Attach the Backrest Board (#39) to Middle Vert ical Frame. Secure it with two M8 x 2 3/8” Allen Bolts (#103) and two Ø 5/8” Washers (#[...]

(#87). Push the Butterfly Arm Foam Roll (#64) to Right Butterfly. Repeat same step to install the Left Butterfly (#12). B.) Insert two Swivel Pulley Brackets (#15) into the holes on the Butterfly Pulley Bracket (#14). Secure each Swivel Pulley Bracket with one M 12 x 5” Hex Bolt (#100), two Ø 1” Washer (#108), and one M12 Aircraft Nut (#111). [...]

15 STEP 6 (See Diagram 6 & Cable Loop Diagram) A.) Attach one end of 113” Butterfly Cable (#45) to t he clip on Left Butterfly (#12). Draw the Cable to the left Swivel Pulley Bracket (#15).[...]

B.) Attach a Pulley (#62) and two Cable Retainers (#78) to the Bracket. C.) Secure them with one M10 x 2” Allen Bolt ( #94), two Ø ¾” Washers (#107), and one M10 Aircraft Nut (#110). D.) Draw the Cable around the Pulley then downward. Attach an Angled Floating Pulley Bracket (#52) to the Cable. Repeat Procedure B above to install a Pulley wit[...]

A.) Attach the two Cross-over Swivel Pulley Br ackets (#10) to left and right Upper Side Frame (#7). Secure each Bracket with four M8 x 3/8” Allen Bolts (#101) and four Ø 5/8” Washers (#106). B.) Remove the U-shaped Connector, Big Washer, and Ball Stopper from one end of 266” Upper Cable (#47). C.) Attach a Pulley (#62) to the left Swivel Br[...]

18 DIAGRAM 7-2[...]

19 UPPER CABLE (#47) LOOP DIAGRAM[...]

20 STEP 8 (See Diagram 8 & Cable Loop Diagram)[...]

A.) Attach one end of the 97” Sliding Weight Post Cable (#46) to the Rear Upper Frame (#18). Secure it with one M10 x 2 3/8” Allen Bolt (#118), two Ø ¾” Washers (#107), and one M10 Aircraft Nut (#110). B.) Attach a Pulley (#62) to top holes on the tw o Double Floating Pulley Brackets (#33). Secure the Pulley with one M10 x 2” Allen Bolt ([...]

DIAGRAM 8 22[...]

STEP 9 (See Diagram 9) A.) Draw the 152” Lower Cable (#44) through t he opening on Foot Plate (#32) to the opening on bottom of Middle Vertical Frame (#9). B.) Attach a Pulley (#62) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#95), two Ø 1” x ½” Pulley Bushings (#57), and one M10 Aircraft Nut (#110). C.) Draw the Cable unde[...]

DIAGRAM 9 24[...]

STEP 10 (See Diagram 10) A.) NOTE: Help of another person is strongly recommended for this step. Place the Lifting Sleeve (#28) in between the two Safety Stop Frames (#25). Align the holes. Insert the Weight Bar (#29) into the Safety Stop Fr ame from one end and through the Lifting Sleeve to the other Safety Stop Frame on the opposite side. Secure [...]

26[...]

SMITH MACHINE PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Front Left Vertical Frame 1 61 1 ½” Square End Cap 1 2 Front Right Vertical Frame 1 62 Pulley 20 3 Rear Left Vertical Frame 1 63 Small Pulley 4 4 Rear Right Vertical Frame 1 64 Butterfly Arm Foam Roll 2 5 Base Frame 2 65 1 ¾” Square End Cap 5 6 Rear Top Beam 1 66 Left Safety Rubber Bumper [...]

MULTI-PURPOSE BENCH HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 28[...]

MULTI-PURPOSE BENCH HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 29[...]

MULTI-PURPOSE BENCH ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended that this machine be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Do not tighten Nuts and Bolts until instructed to do so. B.) Attach the Front Post [...]

STEP 2 (See Diagram 2) A.) Attach the Incline Support (#8) to the middle si de holes on the two Backrest Supports (#7). Secure it with one M10 x 6 7/8” Allen Bolt (#26), two Ø ¾” Washers (#35), and one M10 Aircraft Nut (#37). Do not tighten the Nut and Bolt yet. B.) Attach the bottom side holes on Backrest Supports to the pivot on Main Frame [...]

STEP 3 (See Diagram 3) A.) Place the Backrest Board (#11) onto the Ba ckrest Supports (#7). Secure it with four M8 x 1 5/8” Allen Bolts (#32) and  5/8” Washers (#36). B.) Place the Seat Pad (#10) onto the two Seat Brackets (#4). Secure it with four M8 x 1 1/8” Allen Bolts (#31) and  5/8” Washers (#36). DIAGRAM 3 32[...]

STEP 4 (See Diagram 4) A.) Attach the Leg Developer (#5) to the open bracke t on the Front Post (#2). Secure it with one M10 x 3” Allen Bolt (#29), two  ¾” Washers (#35), and one M10 Aircraft Nut (#37). B.) Insert the Leg Developer Weight Post (#6) into the hole on Leg Developer. Secure it with one M10 x 2 3/8” Allen Bolt (#30), two Ø ¾[...]

33[...]

34 MULTI-PURPOSE BENCH PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Main Frame 1 2 Front Post 1 3 Rear Stabilizer 1 4 Seat Bracket 2 5 Leg Developer 1 6 Leg Developer Weight Post 1 7 Backrest Support 2 8 Incline Support 1 9 Front Stabilizer 1 10 Seat Pad 1 11 Backrest Board 1 12 5/8” x 1 1/8” End Cap 4 13 Foam Tube 3 14 Foam Roll 6 15 Olympic Sleeve[...]

SM-4008 WEIGHT RESISTANCE CHART Station Ratio Example Low Pulley 100% 10 lb. plate creates 10 lb. resistance Butterfly (both arms) 100% 10 lb. plate creates 5 lb. resistance Left Cross-Over 50% 10 lb. plate creates 5 lb resistance Right Cross-Over 50% 10 lb. plate creates 5 lb resistance *Numbers are approximate. Actual resistance may vary. 36[...]

IMPEX ® INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX ® ") warrants this product to be free from defec ts in workmanship and material, under normal use and service conditions, for a period of two years on t he Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obli gation under this Warranty i[...]