Intel HS-872P manual

HS-872P Half-size Single Board Computer User ’ s Manual Edition: 1.0 2007/01/12[...]

HS-872P User’s Manual 2 Copyright Copyright 2007. All rights reserved. This document is copyright ed and all rights are reserved. The information in this docume nt is subject to change without prior notice to make improvements to the products. This document contains pr oprietary information and protected by copyr ight. No part of this document ma[...]

HS-872P User’s Manual 3 Packing List: Please check the package material before you inst all the system. Hardware: HS-872P Single Board Computer x 1 Cable Kit: Audio Port Cable x 1 4-pin to 3-pin A TX cable x 1 PS/2 Keyboard & Mouse Cable x 1 Floppy flat cable x 1 DB25 & DB9 cable x 1 (HS872PDG only) Dual DB9 cable x 1 (HS872PDG2 only) CPU[...]

HS-872P User ’ s Manual 4 Inde x Chapter 1 <Introduction> .................................................................... 6 1.1 <Product Overview> .............................................................................. 6 1.2 <Product Sp ecificatio n> ...................................................................[...]

HS-872P User’s Manual 5 2.15 <Switch and Indicator > ...................................................................... 36 Chapter 3 <System Configuration> ........................................... 38 3.1 <Video Memo ry Setup>........................................................................ 38 Chapter 4 <BIOS Set[...]

HS-872P User ’ s Manual Introduction Product Overv iew 6 Chapter 1 <Introduction> 1.1 <Product Overview> The HS-872P is an all-in-one singl e board computer with PISA bus. with supporting Intel Core 2 Duo / Core Duo / Core solo / Celer on M processor for 533/667MHz front side bus, Intel 945GM and ICH7-M chipset, integrated GMA950 grap[...]

HS-872P User ’ s Manual Introduction Product Spe cification 7 1.2 <Product Specification> General Specification Form Factor Half-size PISA CPU card CPU Intel® Core 2 Duo/ Core Duo/ Core Solo/ Celeron M processor Package type: Micro- FCPGA478 Front side bus: 533/667MHz Memory 1 x 240-pin DDR2 400/533/667MHz SDRAM up to 2GB Unbufferred, none[...]

HS-872P User ’ s Manual Introduction Product Specification 8 Type Triple speed 10/100/1000Base-T auto-switching Fast Ethernet Full duplex, IEEE802.3U compliant Connector External two RJ45 connectors with LED on rear I/O panel Solid St ate Disk Interface Flash Type Compact Flash Type II for Compact Flash Card or Micro Drive ISA Interface ISA Bridg[...]

HS-872P User ’ s Manual Introduction Mechanical Draw in g 9 1.3 < Mechanical Drawing >[...]

HS-872P User ’ s Manual Introduction Block Diagram 10 1.4 <Block Diagram> Intel Y onah Processo r Intel GMA950 Graphics 945GM ICH7-M BIOS AC97 A LC655 HDTV ＆ LV D S ＆ DVI W83627THG 2 x SA T A CompactFlash ＆ IDE 2 x Serial port s 4 x USB2.0 port s 8-bit GPIO Intel 82573L 2 x GLAN 1 x 240-pin DDR2 533/667MHz up to 2GB 1 x Parallel port [...]

HS-872P User ’ s Manual 11 (This Page is Left for Blank)[...]

HS-872P User ’ s Manual Hardw are Setup Connector Location 12 Chapter 2 <Hardware Setup> 2.1 <Connector Location> SYSF AN CN_IR IDE CN_L VDS CDIN CN AUDIO CN_DIO SA T A 1/2 JFRNT CN_PS DC_IN CN_HDTV CN_COM2 CPUF AN CN_USB1/2 CN_DVI FDD MINIPCI CN_INV CN_A TKB CN_LPT DDRII_A CN_COM1[...]

HS-872P User ’ s Manual Hardw are Setup Connector Location 13 PS2 RJ45_1 RJ45_2 CRT CF[...]

HS-872P User ’ s Manual Hardw are Setup Connector Reference 14 2.2 <Connector Reference> 2.2.1 <Internal Connecto r> Connector Function Remark DDRII_A 240 –pin DDR2 SDRAM DIMM socket S tandard IDE 44-pin primary IDE connector Slim FDD 26-pin floppy connector Slim S_A T A1/2 7-pin Serial A T A connector S tandard DC_IN 4-pin A T pow [...]

HS-872P User ’ s Manual Hardw are Setup Jumper Reference 15 2.3 <Jumper Reference> Jumper Function JRTC CMOS Operating/Clear Setting JVLCD LCD Panel V oltage Setting JCRT CR T attach select setting JCSEL1/2 COM2 RS232/422/485 mode setting JRTC JVLCD JCSEL1 JCSEL2 JCRT[...]

HS-872P User ’ s Manual Hardw are Setup CPU & Memory Setup 16 2.4 < CPU and Memory Setup > 2.4.1 <CPU Setup> The board comes with the socket47 9 for Intel Core 2 Dual/Core Dual /Core so lo processor , it supports new generation of Intel Core 2 Dual/C ore Dual /Core sol o processor with 533/667MHz of front side bus and 2MB L2 cache[...]

HS-872P User ’ s Manual Hardw are Setup Memory Setup 17 2.4.2 <Memory Setup> HS-872P has one 240-pin DDR2 DIMM support up to 2GB of memory capacity . The memory frequency supports 533/667MHz. Only Non-ECC memor y is supported. Dual-Channel technology is supported while applying t wo same modules on one of each group. Notice: When appl ying [...]

HS-872P User ’ s Manual Hardw are Setup CMOS Setup 18 2.5 <CMOS Setup> The board’s data of CMOS can be setting in BIOS. If the board refus es to boot due to inappropriate CMOS setting s, here is how to proc eed to clear (reset) t he CMOS to its default values. Jumper: JRTC T ype: Onboard 3-pin jumper JRTC Mode 1-2 Clear CMOS 2-3 Normal Op[...]

HS-872P User ’ s Manual Hardw are Setup Enhanced IDE Interface 19 2.6 <Enhanced IDE Interface> The board has one Ultra A T A33 IDE interf ace to sup port up to 2 A T API devices, and one Compact Flash T ype II socket on the solder side. IDE 1 44[...]

HS-872P User ’ s Manual Hardw are Setup Serial A T A Interface 20 2.7 <Serial A T A interface> Based on Intel ICH7-M, the board provides two Se rial A T A interfaces w ith up to 150MB/s of transfer rate . 2.8 <LAN Interface> The Intel 82573L supports triple speed of 10 /100/1000Base-T , with IEEE802.3 compliance and W ake-On-LAN suppo[...]

HS-872P User ’ s Manual Hardw are Setup Onboard Display Interface 21 2.9 <Onboard Display Interface> Based on Intel 945GM chipset with built-in G MA (Graphic Media Accelerator) 950 graphics, the board provides one DB15 connector on real external I/O port, and one 40-pin L VDS interface with 5-pin LCD backlight inverter connector . The board[...]

HS-872P User ’ s Manual Hardw are Setup Digita l Display 22 2.9.2 <Digit al Display > The board provides one 40-p in L VDS connector for 18-bit dual channel panels, supports up to 1600 x 1200 (UXGA) of resolution, with one LCD backlight inve rter connector and one jumper for panel voltage setting CN_L VDS 39 40 1 2 CN_INV 5 1 JVLCD 3 1[...]

HS-872P User ’ s Manual Hardw are Setup Digita l Display 23 Connector: CN_INV Connector: JVLCD Type: 5-pin LVDS Power Header Type: 3-pin Pow er select Header Connector model: JST B5B-XH-A Pin Description Pin Description 1 +12V 1 VCC(5V) 2 GND 2 LCDVCC 3 GND 3 VCC3(3.3) 4 GND 5 ENABKL Connector: CN_LVDS Type: onboard 40-pin connector for LVDS conn[...]

HS-872P User ’ s Manual Hardw are Setup Digita l Display 24 To setup the LCD, y ou need the component below: 1. A panel with LVDS interfaces. 2. An inverter for panel’s backlight power. 3. A LCD cable and an inverter cable. For the cables, pleas e follow the pin assignment of t he connector to m ake a cable, becaus e every panel has it s own pi[...]

HS-872P User ’ s Manual Hardw are Setup DVI Interface 25 2.9.3 <DVI Interface > The board also comes with a DVI interface with Chrontel CH7307C for digital video interface. Connector: CN_DVI Connector type: 26-pin header connector (pitch = 2.54mm) Pin Number Assignment Pin Number A ssign ment 1 TX1+ 2 TX1- 3 Ground 4 Ground 5 TXC+ 6 TXC- 7 [...]

HS-872P User ’ s Manual Hardw are Setup TV-out Interface 26 2.9.4<TV-out Interface> The board provides an HDT V interface with Intel 945GM, supports P AL and NTSC of TV system, and display (clone or extended de sktop) function with CR T ,L VDS,DVI. Connector: CN_HDTV Connector type: 10-pin header HDTV connector (pitch = 2.54mm) Pin Number A[...]

HS-872P User ’ s Manual Hardw are Setup TV-out Interface 27 To connect the TV set, please follow the diagram below to setup y our system: YPrPb Component Cable ( For HDTV )[...]

HS-872P User ’ s Manual Hardw are Setup TV-out Interface 28 After setup the devices w ell, you need to select the LCD p anel type in the BIOS. The panel type mapping is list below : BIOS panel type se lection form 18 bits Single chann el 24 bits Dual channel NO. Output format NO. Output format 1 640 x 480 9 1024 x 768 2 800 x 600 10 1280 x 768 3 [...]

HS-872P User ’ s Manual Hardw are Setup Onboard A udio Interface 29 2.10 <Onboard Audio Interface> T The board provides the onboar d AC97 5.1-channel audio interface with Realtek ALC655 Connector: CN_A UDIO Type: 10-pin (2 x 5) 1.27mm x 2.54mm-pitch header Pin Description Pin Description 1 LIN_L 2 Ground 3 LIN_R 4 MIC 2 5 MIC 2 6 Ground 7 N[...]

HS-872P User ’ s Manual Hardw are Setup USB2.0 Interface 30 2.11 <USB2.0 Interface> Based on Intel ICH7-M , the board provides 4 USB2.0 ports. The USB2.0 interface provides up to 480Mbps of transferring rate. Interface USB2.0 Controller ICH7-M T ransfer Rate Up to 480Mb/s Output V oltage 500mA CN_USB1/2 1 10 CN_IR 1 5[...]

HS-872P User ’ s Manual Hardw are Setup USB2.0 Interface 31 Connector: CN_IR Type: 5-pin header for SIR Port Pin Description 1 Vcc 2 N/C 3 IRRX 4 Ground 5 IRTX Connector: CN_USB1/2 Type: 10-pin (5 x 2) header for USB Port Pin Description Pin Description 1 VCC 2 VCC 3 Data0- 4 Data1- 5 Data0+ 6 Data1+ 7 Ground 8 Ground 9 Ground 10 N/C PS: The USB2[...]

HS-872P User ’ s Manual Hardw are Setup Serial Port Jumper Setting 32 2.12 <Serial Port Jumper Setting > The board supports one RS232 serial port and on e jumper selectable RS232/422/485 ser ial ports. The jumper JCSEL1 & JCSEL2 can let you configure the communicating mo des for COM2. Connector: CN_COM1/2 Type: 10-pin (5 x 2) 2.54mm x 2[...]

HS-872P User ’ s Manual Hardw are Setup Pow er and Fan Inst allation 33 2.13 <Power and Fan Installation> The board comes with a 4-pin A T power connector for powering the board, three fan connectors for Northbridge, CPU and system. T he boar d also provides a 3- pin A TX function connector . Y ou can just connect the two power connectors w[...]

HS-872P User ’ s Manual Hardw are Setup Power and Fan Installa tion 34 2.13.2 <Fan Connecto rs> Connector: CPUFAN Type: 4-pin fan wafer connector Pin Description Pin Descrip tion 1 Ground 2 +12V 3 Fan Speed Detection 4 Fan Control Connector: SYSFAN Type: 3-pin fan wafer connector Pin Description Pin Description Pin Description 1 Ground 2 +1[...]

HS-872P User ’ s Manual Hardw are Setup GPIO Interface 35 2.14 <GPIO Interface> The board provides a 12-pin General Purpose I/O interface, with programmable 8-bit I/O (4-bit input & 4-bit output). Connector: CN_DIO Type: onboard 2 x 6-pin header, pitch=2.0mm Pin Description Pin Description 1 Ground 2 Ground 3 GP10 4 GP14 5 GP11 6 GP15 7[...]

HS-872P User ’ s Manual Hardw are Setup Switch and Indicator 36 2.15 <Switch and Indicator> The JFRNT provides front control p anel of the board, such a s power button, re set and beeper , etc. Please check well before you connecting the cables on the chassis. Connector: JFRNT Type: onboard 14-pin (2 x 7) 2.54-pitch header Function Signal P[...]

HS-872P User ’ s Manual 37 (This Page is Lef t for Blank)[...]

HS-872P User ’ s Manual System Configuration Video Memory Setup 38 Chapter 3 <System Configuration> 3.1 <V ideo Memory Setup> Based on Intel ® 945GM chipset with GMA (Graphic Media Accelerator) 950, the b oard supports Intel ® DVMT (Dynamic Video Memory T echnology) 3.0, which would allow the video memory to be allocated up to 224MB[...]

HS-872P User ’ s Manual System Configuration Video Memory Setup 39 Fixed + DVMT Memory Size: Y ou can s elect the fixed amount an d the DVMT amount at the same time for a guar anteed video memory and additiona l dynamic video memory , please check the table belo w for available setting. System Memory On-Chip Frame Buffer Size Fixed Memory Size DV[...]

HS-872P User ’ s Manual BIOS Setup BIOS Setup 40 Chapter 4 <BIOS Setup> The motherboard uses the Award BIOS for the s ystem configuration. The Award BIOS in the single board comp uter is a customized ve rsion of the in dustrial standard BIOS for IBM PC AT-compatible computers. It supports Inte l x86 and com patible CPU architecture base d p[...]

HS-872P User ’ s Manual 41 (This Page is Left for Blank)[...]

HS-872P User ’ s Manual I/O Port Pin A ssignment IDE Port 42 Appendix A <I/O Port Pin Assignment> A.1 IDE Port Connector: I D E Type: 44-pin (22 x 2) box header Pin Description Pin Descrip tion 1 Reset 2 Ground 3 D7 4 D8 5 D6 6 D9 7 D5 8 D10 9 D4 10 D11 11 D3 12 D12 13 D2 14 D13 15 D1 16 D14 17 D0 18 D15 19 Ground 20 N/C 21 REQ 22 Ground 23[...]

HS-872P User ’ s Manual Floppy Port 43 A.3 < Floppy Port > Connector: FDD Type: 26-pin connector Pin Description Pin Description 1 VCC 2 INDEX 3 VCC 4 DR0 5 VCC 6 DSKCHG 7 N/C 8 N/C 9 N/C 10 MT R0 11 DRVDE0 12 DIR 13 N/C 14 STEP 15 Ground 16 WRITE DAT A 17 Ground 18 WRITE GAT E 19 Ground 20 TRAK 0 2 1 N / C 2 2 W R P T O 23 Ground 24 RDATA-[...]

HS-872P User ’ s Manual I/O Port Pin A ssignment VGA Port 44 A.6 <VGA Port> Connector: CRT Type: 15-pin D-sub female connector on bracket Pin Description Pin Description Pin Description 1 RED 6 Ground 11 N/C 2 GREEN 7 Ground 12 5VCDA 3 BLUE 8 Ground 13 HSYNC 4 N/C 9 LVGA5V 14 VSYNC 5 Ground 10 Ground 15 5VCLK A.7 <LAN Port> Connector:[...]

HS-872P User ’ s Manual A T Keyboard Port 45 A.9 <A T Keyboard Port> Connector: CN_ATKB Type: 5-pin box header Pin 1 2 3 4 5 Description VCC Ground N/C DAT A CLK A.10 <PS/2 Keyboard & Mouse Port> Connector: PS2 Type: 6-pin Mini-DIN connector on bracket Pin 1 2 3 4 5 6 Description KBD MSD Ground VCC KBC MSC Note: The PS/2 connector[...]

HS-872P User ’ s Manual 46 (This Page is Lef t for Blank)[...]

HS-872P User ’ s Manual Flash BIOS BIOS A uto Flash T ool 47 Appendix B <Flash BIOS> B.1 BIOS Auto Flash T ool The board is based on Award BIOS and can be updated easily by the BIOS auto flash tool. You can download the tool online at the address below : TU ht t p: / / www.a wa rd . co m UT TU ht t p: / / www.c o mm e ll . co m .t w/ s uppo[...]

HS-872P User ’ s Manual System Resources I/O Port A ddress Map 48 Appendix C <System Resources> C1.<I/O Port Address Map>[...]

HS-872P User ’ s Manual System Resources I/O Port A ddress Map 49[...]

HS-872P User ’ s Manual System Resources Memory A ddress Map 50 C2.<Memory Address Map>[...]

HS-872P User ’ s Manual System Resources System IRQ Resources 51 C3.<System IRQ Resources>[...]

HS-872P User ’ s Manual Watch Dog timer Setting W atch Dog timer Setting 52 Appendix D <Watch Dog timer Setting > The watchdog timer makes the system auto-reset while it stops to work for a period. The integrated watchdog timer can be setup as sy stem reset mode by program. Timeout Value Range - 1 to 255 - Second or Minute Program Sample Wa[...]

HS-872P User ’ s Manual 53 (This Page is Lef t for Blank)[...]

HS-872P User ’ s Manual Contact Informatio n Conta ct Information 54 Contact Information Any advice or comment about our pr oducts and service, or anything we can help you please don’t hesitate to contact with us. W e will do our best to support you for your products, project s and business T aiwan Commate Computer Inc. Address 8F , No. 94, Sec[...]