Intel PCI-471LF M2 manual

USER ’ S MANUAL PCI-471LF Celeron ® M Half Size CPU Card With VGA/LAN PCI-471LF M2[...]

Copyright Notice PCI-471LF Celeron® M Hal Size CPU Card With VGA /LAN OPERATION MANUAL COPYRIGHT NOTICE This operation m anual is meant to assist bot h Embedded Computer manufacturers and end users in inst alling and setting up the system. The information contained in this document is subject to change without any notice. This manual is copyrighte[...]

Copyright Notice FCC NOTICE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Ru les. These limits are designed to provide reasonable protection against harm ful interference when the equ ipment is operated in a comm ercial environment. Thi s equipment genera tes, uses, a[...]

Contents TABLE OF CONTENTS CHAPTER 1 INTRODUCTION 1-1 About This Manual ........................................................ 1-2 1-2 System Specification ...................................................... 1-3 1-3 Safety Precautions ......................................................... 1-5 CHAPTER 2 HARDWARE CONFIGURATION 2-1 Jumper &[...]

Contents 2-29 PCI Slot 3.3V Voltage Selection ..….............................. 2-21 2-30 Inverter Connector …………………………………….. 2-21 2-31 Reset / NMI / Clear Watchdog Selection ……………… 2-22 2-32 AT/ATX Power Selection …………………………….. 2-23 2-33 LVDS Connector …………………………?[...]

Contents APPENDIX A EXPANSION BUS PCI Bus Pin Assignment ..............................................…......... A-2 EPCI Connector ..........................………....................….......... A-3 Compact Flash Card Conn ector Pin Assignm ent ……………. A-4 APPENDIX B TECHNICAL SUMMARY Block Diagram ................................[...]

Page:1-1 INTRODUCTION This chapter gives you t he information for PC I-471LF. It also outlines the System specification. Section includes: z About This Manual z System Specifications z Safety precautions Experienced users can skip to chapter 2 on page 2-1 for Quick Start. CHAPTER 1[...]

Chapter 1 Introduction Page: 1-2 PCI-471LF USER ′ S MANUAL 1-1. ABOUT THIS MANUAL Thank you for purchasi ng our PCI-471LF Intel ® Celeron® M Half Si ze Card enhanced with VGA / LAN, which is ful ly PC / AT compatible. PCI-471LF provides faster processin g speed, greater exp andability and can handle more task than before. This ma nual is design[...]

Chapter 1 Introduction PCI-471LF USER ′ S MANUAL Page: 1-3 1-2. SYSTEM SPECIFICATION z CPU : Intel® Celeron® M processor ULV Celeron M 600MHz, without L2 cache System bus frequency at 400MHz Auto detect voltage regulat or z SYSTEM CHIPSET : Intel® 852GM chipset z MEMORY : Supports up to 1GB DDR266 SDR AM. One 200-pin DDR SO-DIMM sockets on boa[...]

Chapter 1 Introduction Page: 1-4 PCI-471LF USER ′ S MANUAL z DISPLAY : Built in Intel 852GM, support CRT, LVDS (18 bit). z IDE INTERFACE : One IDE ports support up to four IDE devices. Supports UDMA 33/66/100. z FLOPPY DISK DRIVER INTERFACE : Supports up to two Floppy Di sk Drives, 3.5" and 5.25". z LAN INTERFACE : Dual ports. LAN 1: In[...]

Chapter 1 Introduction PCI-471LF USER ′ S MANUAL Page: 1-5 z INTERRUPT CONTROLLERS : 82C59 x 2 z INTERRUPT LEVELS : 15 z OPERATING TEMPERATURE : 0 to 60 ° C (32 ° F to 140 ° F) z INPUT POWER REQUIREMENT : ATX power: +5V, +12V. AT power: z BOARD DIMENSION : 185mm x 122mm (7.28” x 4.8”) z BOARD NET WEIGHT : 230 grams (0.51 lb) 1-3. SAFETY PR[...]

Page 2-1 HARDWARE CONFIGURATION ** QUICK START ** CHAPTER 2 Helpful informati on describes the jumper & connector settings, and component locati ons. Section includes: z Jumper & Connector Quick R eference Table z Component Locati ons z Configuration and Jum per settings z Connector’s Pin Assignm ents[...]

Chapter 2 Hardware Config uration Page: 2-2 PCI-471LF USER ′ S MANUAL 2-1. JUMPER & CONNECTOR QUICK REFERENCE TABLE COM Port Connector ....................…..................……… COM1, COM2 COM1 Port RI/Voltage Selection …………………… JP6 COM2 Port RI/Voltage Selection …………………… JP7 RS232/422/485 (COM2) Select[...]

Chapter 2 Hardware Config uration PCI-471LF USER ′ S MANUAL Page: 2-3 2-2. COMPONENT LOCATIONS PCI-471LF Connector, Jumper and Component locations[...]

Chapter 2 Hardware Config uration Page: 2-4 PCI-471LF USER ′ S MANUAL 2-3. HOW TO SET THE JUMPERS You can configure your board by setti ng jumpers. Jum per is consists of two or three met al pins with a plasti c base mounted on the card, and by using a small pl astic " cap " , Also known as the jum per cap (with a meta l contact inside)[...]

Chapter 2 Hardware Config uration PCI-471LF USER ′ S MANUAL Page: 2-5 JUMPER DIAGRAMS 2 pin Jumpe r loo ks l i ke t his Ju mper Ca p looks like this 3 pin Jumpe r loo ks l i ke t his Ju mper Bl ock loo ks l i ke t his JUMPER SETTINGS Looks like this 3 pin Jump er 2-3 pin close( ena bl ed) Looks like this Jumper Bl ock 1-2 pin close( ena bl ed) 2 [...]

Chapter 2 Hardware Config uration Page: 2-6 PCI-471LF USER ′ S MANUAL 2-4. COM PORT CONNECTOR COM1 : COM1 Connector COM1 is fixed as RS-232. The pin assignment is as follows : PIN ASSIGNMENT 1 NDCDA 2 NSINA 3 NSOUTA 4 NDTRA 5 GND 6 NDSRA 7 NRTSA 8 NCTSA 9 NRIA 10 NC COM2 : COM2 Connector The COM2 is selectable as R S-232/422/485. The pin assignme[...]

Chapter 2 Hardware Config uration PCI-471LF USER ′ S MANUAL Page: 2-7 2-5. COM1 RI & VOLTAGE SELECTION JP6 : COM1 RI & Voltage Selection The selections are as follows: SELECTION JUMPER SETTINGS JUMPER ILLUSTRATION RI 1-2 VCC12 3-4 VCC 5-6 ***Manufacturing Default – R I.[...]

Chapter 2 Hardware Config uration Page: 2-8 PCI-471LF USER ′ S MANUAL 2-6. COM2 RI & VOLTAGE SELECTION JP7 : COM2 RI & Voltage Selection The selections are as follows: SELECTION JUMPER SETTINGS JUMPER ILLUSTRATION RI 1-2 VCC12 3-4 VCC 5-6 ***Manufacturing Default – R I.[...]

Chapter 2 Hardware Config uration PCI-471LF USER ′ S MANUAL Page: 2-9 2-7. RS232/422/485 (COM2) SELECTION JP8 : RS-232/422/485 (COM 2) Selection This connector is used to set the COM 2 function. The jumper settings are as follows : COM 2 Function Jumper Settings (pin closed) Jumper Illustrations RS-232 OPEN, OPEN, OPEN RS-422 1-2, 3-4, 9-10 RS-48[...]

Chapter 2 Hardware Config uration Page: 2-10 PCI-471LF USER ′ S MANUAL 2-8. KEYBOARD OR PS/2 MOUSE CONNECTOR DIN : Keyboard or PS/2 M ouse Connector DIN connector can support keyboard, Y-cable, or PS/2 M ouse, user may select the right device to used on “Keyboard or PS/2 M ouse Selection”. The pin assignments are as follows : ASSIGNMENT PIN K[...]

Chapter 2 Hardware Config uration PCI-471LF USER ′ S MANUAL Page: 2-11 2-10. EXTERNAL KEYBOARD CONNECTOR EXKB1 : External Keyboard Connector The pin assignment is as follows : PIN ASSIGNMENT 1 L _ KCLK 2 L _ KDAT 3 GND 4 PS2V5 2-11. RESET CONNECTOR JPAENL (9,11) : Reset Connector. The pin assignment is as follows : PIN ASSIGNMENT 9 GND 11 RST_SW [...]

Chapter 2 Hardware Config uration Page: 2-12 PCI-471LF USER ′ S MANUAL 2-13. ATX POWER BUTTON JPANEL (10,12) : ATX Power Button The pin assignment is as follows : PIN ASSIGNMENT 10 PULL HIGH 12 PWB_SIOJ 2-14. EXTERNAL SPEAKER CONNECTOR JPANEL (1,3) : External Speaker Connector The pin assignment is as follows : PIN ASSIGNMENT 1 SPK3 3 SPK_VCC 2-1[...]

Chapter 2 Hardware Config uration PCI-471LF USER ′ S MANUAL Page: 2-13 2-16. KEYLOCK CONNECTOR JPAENL (13,14) : Keylock Connector The pin assignment is as follows: PIN ASSIGNMENT 13 KEYLOCK 14 GND 2-17. IRDA CONNECTOR JPANEL(17,18,19,20) : IrDA (Infrared) Connector The pin assignments are as follows: PIN ASSIGNMENT 17 VCC 18 GND 19 IRTX2 20 IRRX2[...]

Chapter 2 Hardware Config uration Page: 2-14 PCI-471LF USER ′ S MANUAL 2-19. SYSTEM FAN CONNECTOR JSFAN1 : System Fan connector The pin assignment is as follows: PIN ASSIGNMENT 1 GND 2 +12V 3 FAN0 2-20. CLEAR CMOS DATA SELECTION JP10 : Clear CMOS Data Selection The selections are as follows : FUNCTION JUMPER SETTING (pin closed) JUMPER ILLUSTRATI[...]

Chapter 2 Hardware Config uration PCI-471LF USER ′ S MANUAL Page: 2-15 2-21. VGA CONNECTOR VGA : VGA CRT Connector The pin assignments are as follows: PIN ASSIGNMENT 1 RED 2 GREEN 3 BLUE 4 NC 5 GND 6 GND 7 GND 8 GND 9 VCC 10 GND 11 NC 12 VGA DDA 13 HSYNC 14 VSYNC 15 VGA DDC CLK[...]

Chapter 2 Hardware Config uration Page: 2-16 PCI-471LF USER ′ S MANUAL 2-22. HARD DISK DRIVE CONNECTOR IDE1: Hard Disk Drive Connector The pin assignments are as follows: PIN ASSIGNMENT PIN ASSIGNMENT 1 IDERST 2 GND 3 PDD7 4 PDD8 5 PDD6 6 PDD9 7 PDD5 8 PDD10 9 PDD4 10 PDD11 11 PDD3 12 PDD12 13 PDD2 14 PDD13 15 PDD1 16 PDD14 17 PDD0 18 PDD15 19 GN[...]

Chapter 2 Hardware Config uration PCI-471LF USER ′ S MANUAL Page: 2-17 2-23. FLOPPY DISK DRIVE CONNECTOR FDD1 : Floppy Disk Drive Connector You can use a 34-pin daisy-chain cable to connect two-FDDs. On one end of this cable is a 34-pin fl at cable to attach the FDD on the board, and the other side is attaches two FDDs. The pin assignments are as[...]

Chapter 2 Hardware Config uration Page: 2-18 PCI-471LF USER ′ S MANUAL 2-24. PRINTER CONNECTOR PRNT1 : Printer Connector As to link the Printer t o the card, you need a cable to connect both DB 25 connector and parallel port. The pin assignments are as follows : PIN ASSIGNMENT PIN ASSIGNMENT 1 STB 14 AFD# 2 PDR0 15 ERROR# 3 PDR1 16 PAR_INIT# 4 PD[...]

Chapter 2 Hardware Config uration PCI-471LF USER ′ S MANUAL Page: 2-19 2-25. UNIVERSAL SERIAL BUS CONNECTOR USB1: Universal Serial Bus Connector The pin assignments are as follows: PIN ASSIGNMENT 1 VCC 2 USBC0N 3 USBC0P 4 GND 5 GND 6 VCC 7 USBC1N 8 USBC1P 9 GND 10 GND 2-26. LAN CONNECTOR LAN1: LAN Connector The pin assignments are as follows: PIN[...]

Chapter 2 Hardware Config uration Page: 2-20 PCI-471LF USER ′ S MANUAL 2-27. ATX POWER CONNECTOR PW1 : ATX Power Connector The pin assignments are as follows: PIN ASSIGNMENT 1 VCC 2 VCC 3 GND 4 GND 5 VCC12 6 V5SB 7 VCC 8 GND 9 PS_ON 10 VCC12J 2-28. 5VSB CONNECTOR JP3 : ATX Power Signal Connector The pin assignments are as follows: PIN ASSIGNMENT [...]

Chapter 2 Hardware Config uration PCI-471LF USER ′ S MANUAL Page: 2-21 2-29. PCI SLOT 3.3V VOLTAGE SELECTION JP9 : PCI Slot 3.3V Voltage Sel ection. The selections are as follows: FUNCTION JUMPER SETTING (pin closed) JUMPER ILLUSTRATION 3.3V from Mainboard 1-2 3-4 1 2 3 4 3.3V from Backplane open 1 2 3 4 2-30. INVERTER CONNECTOR JP14 : Inverter C[...]

Chapter 2 Hardware Config uration Page: 2-22 PCI-471LF USER ′ S MANUAL 2-31. RESET/NMI/CLEAR WATCHDOG SELECTION JP2 : Reset/NMI/C lear Watchdog Selection The selections are as follows: FUNCTION JUMPER SETTING (pin closed) JUMPER ILLUSTRATION RESET 1-2 JP2 NMI 3-4 JP2 CLEAR WATCHDOG 5-6 JP2 SMI 9-10 JP2 ***Manufacturing Default is set as open. [...]

Chapter 2 Hardware Config uration PCI-471LF USER ′ S MANUAL Page: 2-23 2-32. AT/ATX POWER SELECTION JP1, JP2 (1-2), JP15 : AT/ ATX Power Selection The selections are as follows: JUMPER SETTING (pin closed) FUNCTION JP1 JP2 (1-2) JP15 JUMPER ILLUSTRATION AT Open Close Close ATX Close Open Open ***Manufacturing Default is set as ATX.[...]

Chapter 2 Hardware Config uration Page: 2-24 PCI-471LF USER ′ S MANUAL 2-33. LVDS CONNECTOR CNT3 : LVDS Connector. The pin assignments are as follows: 2 1 CN T 3 PIN ASSIGNMENT PIN ASSIGNMENT 1 LCD_VCC 2 GND 3 ZCM 4 ZCP 5 GND 6 Z2M 7 Z2P 8 GND 9 Z1M 10 Z1P 11 Z3P 12 Z3M 13 Z0P 14 Z0M 15 GND 16 YCP 17 YCM 18 GND 19 Y2P 20 Y2M 21 GND 22 Y1P 23 Y1M [...]

Chapter 2 Hardware Config uration PCI-471LF USER ′ S MANUAL Page: 2-25 2-34. LVDS PANEL VOLTAGE SELECTION JP12 : LVDS Panel Voltage Selection. The selections are as follows: SELECTION JUMPER SETTING JUMPER ILLUSTRATION LVDS_VCC3 2-3 LVDS_VCC5 1-2[...]

Page: 3-1 SOFTWARE UTILITIES This chapter comprises the detaile d inform ation of VGA driver, LAN driver, and Flash BIOS update . It also describes how to install the watchdog tim er configuration. Section includes: z VGA Driver Utility z Flash BIOS Update z LAN Driver Utility z Intel® Chipset Software Installation Utility z USB2.0 Chipset Softwar[...]

Chapter 3 Software Configuration Page:3-2 PCI-471LF USER ′ S MANUAL 3-1. INTRODUCTION Enclosed with our PCI-471LF packag e is our driver utility, which may comes in a form of a CD ROM disc or floppy diskettes. For CD ROM disc user, you will only need some of the files contained in the CD ROM disc, please kindly refer to the following chart: Filen[...]

Chapter 3 Software Configuration PCI-471LF USER ′ S MANUAL Page:3-3 3-2-1. Installation of VGA Driver: To install the VGA Driver, simp ly follow the following steps: 1. Place insert the Utility Disk into Floppy Disk Drive A/B or CD ROM drive. 2. Under Windows 9X/NT4.0/2000/XP system, go to t he directory where VGA driver is located. 3. Click Setu[...]

Chapter 3 Software Configuration Page:3-4 PCI-471LF USER ′ S MANUAL FLASH MEMORY WRITER v7.XX (C) Award Software 2001 All Ri ghts Reserved Flash Type – SST 49LF004A /3.3V File Name to Program: H20bxxxx.bin Checksum: XXXXX Error Message: Do You W ant To Save BIOS (Y/N) If you want to save up the original B IOS, enter " Y " and press &l[...]

Chapter 3 Software Configuration PCI-471LF USER ′ S MANUAL Page:3-5 FLASH MEMORY WRITER v7.XX (C) Award Software 2001 All Ri ghts Reserved Flash Type – SST 49LF004A /3.3V File Name t o Program: H20bxxxx.bin Checksum: XXXXX Reset System or Power off to accomplish update process! F1: Reset F10: Exit Please reset or power off the system, and then [...]

Chapter 3 Software Configuration Page:3-6 PCI-471LF USER ′ S MANUAL 3-5. INTEL® C HIPSET SOFTWARE INSTALLATION UTILITY 3-5-1. Introduction The Intel® Chipset Software Installatio n Utility installs to the target system the Windows* INF files that outline to the operating system how the chipset components will be confi gured. This is needed for [...]

Chapter 3 Software Configuration PCI-471LF USER ′ S MANUAL Page:3-7 3-6. USB2.0 SOFTWARE INSTALLATION UTILITY 3-6-1. Installation of Utility for Windows 98SE/ 2000/XP Intel USB 2.0 Enhanced Host Controller dri ver can only be used on Windows 98SE, Windows 2000 and Windows XP on Intel Desktop boards. It should be installe d right after the OS inst[...]

Chapter 3 Software Configuration Page:3-8 PCI-471LF USER ′ S MANUAL 3-7. WATCHDOG TIMER CONFIGURATION The I/O port address of the watchdog tim er is 2E(hex) and 2F(hex). 2E (hex) is the address port. 2F(hex) is the data port . User must first assign t he address of register by writing address value into add ress port 2E(hex ), then write/read dat[...]

Chapter 3 Software Configuration PCI-471LF USER ′ S MANUAL Page:3-9 Mov al, 07h ; Select Logical Device 8 of watchdog tim er Out dx,al Inc dx Mov al, 08h Out dx,al ;----------------------------------------------------------- Dec dx ; Set second as counting unit Mov al, 0f5h Out dx,al Inc dx In al,dx And al,not 08h Out dx,al ;---------------------[...]

Page: 4-1 AWARD BIOS SETUP This chapter shows how to set up the Award BIOS. Section includes: z Introduction z Entering Setup z The Standard CMOS Features z The Advanced BIOS Features z The Advanced Chipset Features z Integrated Peripherals z Power Management Setup z PNP/PCI Configurati on z PC Health Status z Frequency Control z Load Fail-Safe Def[...]

Chapter 4 Award BIOS Setup Page: 4-2 PCI-471LF USER ′ S MANUAL 4-1. INTRODUCTION This chapter will show you the function o f the BIOS in managing the features of your system . The PCI-471LF Celeron® M Half Size CPU Card is equipped with the BIOS for system ch ipset from Award Software Inc. This page briefly explains the functi on of the BIOS in [...]

Chapter 4 Award BIOS Setup PCI-471LF USER ′ S MANUAL Page: 4-3 4-2. ENTERING SETUP When the system is powered on , the BIOS will enter th e Power-On Self Test (POST) routines and the following message will appear on the lower screen: PRESS <DEL> TO ENTER SETUP, ESC TO SKIP MEMORY TEST As long as this message i s present on the screen you ma[...]

Chapter 4 Award BIOS Setup Page: 4-4 PCI-471LF USER ′ S MANUAL 4-3. THE STANDARD CMOS FEATURES Highlight t he 〝 STANDARD CMOS FEATURES 〞 and press the <ENTER> key and the screen will d isplay the following tab le: Phoenix - AwardBIOS CMOS Setup Utility Standard CMOS Features Date (mm:dd:yy) Time (hh:mm:ss) Wed, Jan 1 2003 22 : 58 : 59 I[...]

Chapter 4 Award BIOS Setup PCI-471LF USER ′ S MANUAL Page: 4-5 IDE Primary Master / Slav e: IDE Secondary Master / Slav e: The BIOS can automatically detect th e specificati ons and optimal operating mode of al most al l IDE hard drives. When you select type AUTO for a hard drive, the BIOS detect its specifica tions during POST, every time syst e[...]

Chapter 4 Award BIOS Setup Page: 4-6 PCI-471LF USER ′ S MANUAL  LBA (Logical Block Addressing): During drive accesses, the IDE controller transforms the dat a address described by sector, head and cylinder number into a physical block address, significantly i mproving data transfer rates. For drives greater than 1024 cylinders. DRIVE A AND DRI[...]

Chapter 4 Award BIOS Setup PCI-471LF USER ′ S MANUAL Page: 4-7 HARD DISK ATTRIBUTES: Type Cylinders Heads V-P comp LZone Sect Capacity 1 306 4 128 305 17 10 2 615 4 300 615 17 20 3 615 6 300 615 17 30 4 940 8 512 940 17 62 5 940 6 512 940 17 46 6 615 4 65535 615 17 20 7 642 8 256 511 17 30 8 733 5 65535 733 17 30 9 900 15 65535 901 17 112 10 820 [...]

Chapter 4 Award BIOS Setup Page: 4-8 PCI-471LF USER ′ S MANUAL 4-4. THE ADVANCED BIOS FEATURES Choose the 〝 ADVANCED BIOS FEATURES 〞 in the main menu, the screen shown as below. Phoenix - AwardBIOS CMOS Setup Utility Advanced BIOS Features Item Help CPU L1 & L2 Cache Quick Power On Self Test First Boot Device Second Boot Device Boot Up Fl[...]

Chapter 4 Award BIOS Setup PCI-471LF USER ′ S MANUAL Page: 4-9 FIRST/SECOND/ BOOT DEVICE: The BIOS attempt to load the operating system from the devices in the sequence selected in these items. BOOT UP FLOPPY SEEK: You may enable / disable this item to define whether the system will look for a floppy disk drive to boot at power-on, or proceed dir[...]

Chapter 4 Award BIOS Setup Page: 4-10 PCI-471LF USER ′ S MANUAL OS SELECT FOR DRAM >64MB : Select the operating sy stem that is running with greater t han 64MB or RAM on the system. You m ay choose OS2 or Non-OS2. 4-5. ADVANCED CHIPSET FEATURES Choose the 〝 ADVANCED CHIPSET FEATURES 〞 fr om t he main men u, the screen shown as below. Phoen[...]

Chapter 4 Award BIOS Setup PCI-471LF USER ′ S MANUAL Page: 4-11 DRAM DATA INTEGRITY MODE: Select Parity or ECC (error-correcting c ode), according to the type of installed DRAM. SYSTEM BIOS CACHEABLE: Selecting Enabled allows caching of the system BIOS ROM at F0000h- FFFFFh, resulting in better system perform ance. However, if any program writes [...]

Chapter 4 Award BIOS Setup Page: 4-12 PCI-471LF USER ′ S MANUAL 4-6. INTEGRATED PERIPHERALS Choose 〝 INTEGRATED PERIPHERALS 〞 fro m th e ma in se tu p men u , a display will be shown o n screen as below: Phoenix - AwardBIOS CMOS Setup Utility Integrated Peripherals Item Help X OnChip IDE Device X Onboard Device X SuperIO Device Watch Dog Time[...]

Chapter 4 Award BIOS Setup PCI-471LF USER ′ S MANUAL Page: 4-13 VIA ONCHIP IDE DEVICE: The options for these item s are found in its sub m enu. By pressing the <ENTER> key, you are prom pt to enter the sub m enu of the detailed opt ions as shown below: Phoenix – Award CMOS Setup Utility VIA OnChip IDE Device Item Help OnChip Primary PCI I[...]

Chapter 4 Award BIOS Setup Page: 4-14 PCI-471LF USER ′ S MANUAL hard drive and your system software bot h support Ultra DMA/33, select Auto to enable BIOS support. 4. IDE HDD Block Mode Block mode is also called block transfer, multiple commands, or multiple sector read/write. If your IDE hard drive supports block mode (most new drives do), selec[...]

Chapter 4 Award BIOS Setup PCI-471LF USER ′ S MANUAL Page: 4-15 SUPER IO DEVICE: The options for these item s are found in its sub m enu. By pressing the <ENTER> key, you are prom pt to enter the sub m enu of the detailed opt ions as shown below: Phoenix – Award CMOS Setup Utility SuperIO Device Item Help Onboard FDC Controller Onboard Se[...]

Chapter 4 Award BIOS Setup Page: 4-16 PCI-471LF USER ′ S MANUAL This item allows you to select IR transmission routes, one is RxD2m, TxD2 (COM Port) and the other is IR-R x2Tx2 8. Onboard Parallel Port This item allows you to determine access onboard parallel port controller with which I/O address. 9. Parallel Port Mode Select an operating m ode [...]

Chapter 4 Award BIOS Setup PCI-471LF USER ′ S MANUAL Page: 4-17 4-7. POWER MANAGEMENT SETUP Choose 〝 POWER MANAGEMENT SETUP 〞 option on the m ain me nu, a display will be shown o n screen as below : Phoenix - AwardBIOS CMOS Setup Utility Power Management Setup ACPI Function Power Management Video Off Method Video Off In Suspend MODEM Use IRQ [...]

Chapter 4 Award BIOS Setup Page: 4-18 PCI-471LF USER ′ S MANUAL VIDEO OFF OPTION: When enabled, this feature allows the VGA adapter to operate in a power saving mode. Always On Monitor will remain on during power saving modes. Suspend --> Off Monitor blanked when the systems enters the Suspend mode. Susp,Stby --> Off Monitor blanked when th[...]

Chapter 4 Award BIOS Setup PCI-471LF USER ′ S MANUAL Page: 4-19 RESUME BY ALARM: When Enabled, your can set the date and tim e at which the RTC (real-time clock) alarm awakens the system from Suspend mode. PM EVENTS: PM events are I/O events whose o ccurrence can preven t the system from entering a power saving m ode or can aw aken the system fro[...]

Chapter 4 Award BIOS Setup Page: 4-20 PCI-471LF USER ′ S MANUAL 4-8. PNP/PCI CONFIGURATION Choose 〝 PNP/PCI CONFIGURATION 〞 f ro m th e main men u , a d is pl ay will be shown on screen as below: Phoenix - AwardBIOS CMOS Setup Utility PnP/PCI Configurations Reset Configuration Data [Disabled] Item Help Resources Controlled By x IRQ Resources [...]

Chapter 4 Award BIOS Setup PCI-471LF USER ′ S MANUAL Page: 4-21 RESOURCE CONTROLLED BY: The Award Plug and Play B ios can automat ically configure all of the booth and Plug and Play-compatible devices. However, this capability means absolutely nothing unl ess you are using a Plug and Play operating system such as Windows 95. By choosing “manual[...]

Chapter 4 Award BIOS Setup Page: 4-22 PCI-471LF USER ′ S MANUAL 4-9. PC HEALTH STATUS Choose 〝 PC HEALTH STATUS 〞 from the main menu, a display will be shown on screen as below: Phoenix - AwardBIOS CMOS Setup Utility PC Health Status Item Help Current Warning Temperature Current CPU Temperature Current SYSTEM Fan Speed Current CPU Fan Speed V[...]

Chapter 4 Award BIOS Setup PCI-471LF USER ′ S MANUAL Page: 4-23 VCORE: This item shows you the current system voltage. 3.3V / +5V / +12V / -12V / -5V: Show you the voltage of 3.3V/ +5V/+12V/-12V/-5V. 4-10. FREQUENCY CONTROL Choose 〝 FREQUENCY CONTROL 〞 fr om t he main men u, a d is pl ay will be shown on screen as below: Phoenix - AwardBIOS C[...]

Chapter 4 Award BIOS Setup Page: 4-24 PCI-471LF USER ′ S MANUAL 4-11. LOAD FAIL-SAFE DEFAULTS By pressing the <ENTER> key on this item , you get a confirm ation dialog box with a message si milar t o the following: Load Fail-Safe Defaults ( Y/N ) ? N To use the BIOS default values, change the prom pt to "Y" and press the <Enter[...]

Chapter 4 Award BIOS Setup PCI-471LF USER ′ S MANUAL Page: 4-25 4-13. PASSWORD SETTING User is allowed to set eit her supervisor or user password, or both of them. The difference is that the supervisor password can ente r and change the options of the setup m enus while t he user password can enter only but do not have the authority to change the[...]

Chapter 4 Award BIOS Setup Page: 4-26 PCI-471LF USER ′ S MANUAL 4-14. SAVE & EXIT SETUP After you have complet ed adjusting all the sett ings as required, you m ust remember to save these setting into the CMOS RAM. To save th e settings, select “SAVE & EXIT SETUP” and press <Enter>, a display will be shown as follows: Phoenix - [...]

Chapter 4 Award BIOS Setup PCI-471LF USER ′ S MANUAL Page: 4-27 4-15. EXIT WITHOUT SAVING If you wish to cancel any changes you have m ade, you ma y select the “EXIT WITHOUT SAVING” and the orig inal setting stored in the CMOS will be retained. The screen will be sho wn as below: Phoenix - AwardBIOS CMOS Setup Utility ► Standard CMOS Featur[...]

Page: A-1 EXPANSION BUS This appendix indicates the pi n assignments. Section includes: z PCI BUS Pin Assignment z PPCI BUS Pin Assignment z Compact Flash Ca rd Connector Pin Assignm ent APPENDIX A[...]

Appendix A Expansion Bus Page: A-2 PCI-471LFUSER ′ S MANUAL PCI BUS PIN ASSIGNMENT Like ISA-BUS connector, the PCI-BUS edge connector i s also divided into two sets: one consists of 98-pi n; the other consists of 22-pi n. The pin assignments are as follows : B52 A52 B62 A 62 A49 B49 B1 A1 B A B A PIN ASSIGNMENT PIN ASSIGNMENT PIN ASSIGNMENT PIN A[...]

Appendix A Expansion Bus PCI-471LF USER ′ S MANUAL Page: A-3 EPCI CONNECTOR You will find a EPCI connector in our PCI-471LF. The pin assignments are as follows: PIN ASSIGNMENT PIN ASSIGNMENT A1 GND B1 GND A2 AD0 B2 AD1 A3 AD2 B3 AD3 A4 AD4 B4 AD5 A5 AD6 B5 AD7 A6 AD8 B6 AD9 A7 AD10 B7 AD11 A8 VCC B8 VCC A9 AD12 B9 AD13 A10 AD14 B10 AD15 A11 AD16 [...]

Appendix A Expansion Bus Page: A-4 PCI-471LFUSER ′ S MANUAL COMPACT FLASH CARD CONNECTOR PIN ASSIGNMENT The pin assignments of Compact Flash Card connector are stated below. PIN ASSIGNMENT PIN Assignment 1 GND 26 -CD1 2 D03 27 D111 3 D04 28 D121 4 D05 29 D131 5 D06 30 D141 6 D07 31 D151 7 -CS0 32 -CS11 8 A102 33 -VS1 9 -ATASEL 3 4 -IORD 10 A092 3[...]

Page: B-1 TECHNICAL SUMMARY This section introduce you the m aps concisely. Section includes: z Block Diagram z Interrupt Map z RTC & CMOS RAM Map z Timer & DMA C hannels Map z I / O & Memory M ap APPENDIX B[...]

Appendix B Technical Summary Page: B-2 PCI-471LF USER ′ S MANUAL BLOCK DIAGRAM[...]

Appendix B Technical Summary PCI-471LF USER ′ S MANUAL Page: B-3 INTERRUPT MAP IRQ ASSIGNMENT 0 System TIMER 1 Keyboard 2 Cascade 3 Serial port 2 4 Serial port 1 5 Available 6 Floppy 7 Parallel port 1 8 RTC clock 9 Available 10 Available 11 Available 12 PS/2 Mouse 13 Math coprocessor 14 IDE1 15 IDE2[...]

Appendix B Technical Summary Page: B-4 PCI-471LF USER ′ S MANUAL RTC & CMOS RAM MAP CODE ASSIGNMENT 00 Seconds 01 Second alarm 02 Minutes 03 Minutes alarm 04 Hours 05 Hours alarm 06 Day of week 07 Day of month 08 Month 09 Year 0A Status regist er A 0B Status register B 0C Status register C 0D Status regist er D 0E Diagnostic status byte 0F Sh[...]

Appendix B Technical Summary PCI-471LF USER ′ S MANUAL Page: B-5 TIMER & DMA CHANNELS MAP Timer Channel Map : Timer Channel Assignment 0 System timer interrupt 1 DRAM Refresh request 2 Speaker tone generator DMA Channel Map : DMA Channel Assignment 0 Available 1 Available 2 Floppy 3 Available 4 Cascade 5 Available 6 Available 7 Available[...]

Appendix B Technical Summary Page: B-6 PCI-471LF USER ′ S MANUAL I/O & MEMORY MAP Memory Map : MEMORY MAP ASSIGNMENT 0000000-009FFFF Sy stem memory used by DOS and application 00A0000-00BFFFF Display buffer memory for VGA/ EGA / CGA / MONOCHROME adapter 00C0000-00DFFFF Reserved for I/O device BIOS ROM or RAM buffer. 00E0000-00EFFFF Reserved f[...]