Jet Tools HVBS-56M manual

OW NER'S M A NU A L HVBS-56M Horizont al/Vertical Bandsa w JET EQU I P MEN T & TOOLS, I NC . P.O. BO X 134 9 Phone : 253-351-6000 A W MH C ompany Auburn, WA 98071-1349 Fax: 1- 800-2 74- 6 840 www.j ettoo ls. co m e-ma il jet@j ett ools.c om M-414458 12 /2000[...]

2 Important Information 1-YE AR J ET off e rs a on e -yea r limite d LIM ITED WA RRA NTY warranty on this product R EP LA C EM EN T P A R TS Replac em en t parts f or this tool are a v ail abl e dir ectly fr om JET Equipment & T ools. To pl ace an order, call 1- 800-274-6848. Please ha v e t he f oll ow i ng i nformati on ready: 1. Vi sa, Maste[...]

3 WARNING Read an d understan d the enti re instructio n manual bef ore op erating mach ine. Thi s mach ine is d es i gned and intended fo r use b y pro perl y train ed and experi enced personnel only. I f you are not familiar wi th the proper saf e use of band saws, do not use this machin e until pro per t raining and knowl edge h as been obtained[...]

4 Speci fi cati ons: H VBS- 56M Stoc k Nu mber................................................................................................................................ 414458 Hori zontal Capac ity: Round @ 90 ° ...................................................................................................................................[...]

5 U npacki ng and C lean- U p Note: Read and under stand the enti re manual bef ore attem pting setup or operati on. 1. Rem o v e all cont ents f orm the shippi ng cart on. 2. Inspect cont ents f or shippi ng damage and report any dam age t o your di stribut or. 3. W ipe bed and v ise ass em bl y with c lean cl oth to rem o v e e x c ess oil us ed [...]

6 5. Att ach a cross brace to t he opposite end of the bed usi ng three 5/ 16”x1” hex cap bolt s, six 5/ 16” fl at w asher s, and secure wit h thr ee 5/16” hex nut s. Ti ghten t he nut on the end of t he bed fi rst foll owed by the nuts on t he sides. 6. Att ach a leg to the cross brace using f our 5/16”x 3/ 4” carri age bolt s, f our 5[...]

7 11. Sli de pull ey c o v er ( A, Fi g. 5) ar ound m otor shaft and w orm gear shaf t. Secure wit h tw o hex c ap s c rews and washer s (B, Fig. 5). 12. Lif t m otor with one hand whi le the ot her hand plac es V-belt (C, Fi g.5) on bot h pulley s. 13. Att ach the t ension br acket (D, Fi g. 5) t o the saw bow wit h one 5/16”x 3/4” hex head bo[...]

8 4. Rem o v e two screw s (D, Fig. 7) and plat e (E, Fig . 7). 5. Gui de blade t hrough sl ot in tabl e (A, Fi g. 8) and fasten tab le with tw o screws (B, Fig. 8). 6. Fasten support br acket t o underside of t able using scre w (C, Fig. 8) and he x nut. 7. Ti ghten bolt ( B, Fig 7). El ectri cal Conn ecti ons WA RNING All electri cal conn ections[...]

9 Changing Blade Speed 1. Disco nnect the mach ine from the power sou rce. 2. Pl ace saw arm i n the horizont al posit ion. 3. Loosen tensi oning pl at e he x nut (A, Fi g.10). 4. Open pull ey cov er (B, Fig. 10) . Lif t mot or with one hand whil e pl acing t he belt (C, Fi g. 10) on t he desired pull ey com b i nati on. 5. Tensi on belt by pr ess [...]

1 0 Changing Blades 1. Disco nnect machin e f r o m the power sou rce. 2. Raise the saw arm t o the v er tical positi on and loc k in place wit h lock l e v er. 3. Open bl ade cover by r e m ov ing the sm all knob found on t he topsi de o f t he bow. 4. Rem o v e r ed blade guards by removi ng t w o scr e w s. WA RNING It i s essenti al t hese two [...]

1 1 A dj usting Blade Tracking WA RNING Blad e tracking adjust ment requires ru nning th e saw with the back cover op en! Thi s adj ustment must be co m p let e d b y qualifi ed per sons only ! Fai lure to co m p ly may cause seri ous injury! Bl ade tracki ng has been set at t he f actory and should not need adj ustm ent. If bl ade tracki ng needs [...]

1 2 Adjusting Automat ic Shut-Off The saw should stop af t er the cut has been com pleted: • If the saw com plet es the cut and conti nues to run, ad j ust the stop ti p (A, Fig. 17) down. • If the saw shuts off be f ore the c ut is com plete, adj ust the stop t ip (A, Fi g. 17) up. • If the saw stops cutt i ng but conti nues to run, adjust t[...]

1 3 Breakdown for Bow As semb ly[...]

1 4 Breakdown for Base A s sembly[...]

1 5 Parts Li st for th e HVB S-56M Band saw Inde x Par t No. No . Descrip tion Siz e Qty. 1 .......... TS- 0051031 .............................. He x C ap Bo lt ......................................... 5/1 6”x3/4” ................... 4 2 .......... TS- 0561011 .............................. He x N ut...........................................[...]

1 6 Inde x Par t No. No . Descrip tion Siz e Qty. 52 ........ TS- 0081071 .............................. Hex C ap Bo lt ......................................... 5/1 6”x1- 1/2” ................ 1 53 ........ TS- 0091071 .............................. Hex C ap Scr ew ..................................... 7 /16” x 2” ...................... 1 [...]

1 7 Inde x Par t No. No . Descrip tion Siz e Qty. 99 ........ HVBS 462-099 ........................... Spa cer .................................................. ................................... 1 10 0 ...... HVBS 462-100 ........................... Fla t Cro ss He ad Scre w .......................... 5/3 2”x3/8” ................... 8 10 1 .[...]